2070 Input File Layout - Connect NCDOT and Signals... · 2013. 4. 2. · Two examples of the input...
Transcript of 2070 Input File Layout - Connect NCDOT and Signals... · 2013. 4. 2. · Two examples of the input...
SHEET OF
Features:
A
1
U
2 3 4 5 6 7 8 9 1O 11 12 13 14
(front view)
FS
ST
L
U
L
SLOT EMPTY
SLOT EMPTY
FS = FLASH SENSE
ST = STOP TIME
ISOLATOR
DC
ISOLATOR
DC
EX. : 1A, 2A, ETC. = LOOP NO.’S
INPUT FILE POSITION LAYOUT
FILE
"I"
FILE
"J"
SLOT EMPTY
SLOT EMPTY
PRE = PREEMPT
ISOLATOR
AC
PRE1
NOT
USED
5
4
4C1A
1
NOT
USED1B
1
6/SYS
SLOT EMPTY
SLOT EMPTY
SLOT EMPTY
SLOT EMPTY
SLOT EMPTY
SLOT EMPTY
SLOT EMPTY
NOT
USED
6 PED
ISOLATOR
DC
2 PED
ISOLATOR
DC
NOT
USED
NOT
USED
SLOT EMPTY
2C
2D
2
2
2A
2B
2
2
A
STD. NO.
2070 Input File Layout
1
U
2 3 4 5 6 7 8 9 1O 11 12 13 14
(front view)
FS
ST
L
U
L
SLOT EMPTY
SLOT EMPTY
FS = FLASH SENSE
ST = STOP TIME
ISOLATOR
DC
ISOLATOR
DC
EX. : 1A, 2A, ETC. = LOOP NO.’S
INPUT FILE POSITION LAYOUT
FILE
"I"
FILE
"J"
SLOT EMPTY
SLOT EMPTY
NOT
USED
1A
1
2A
2B
2
2
2C
2D
2
2
2E
2
NOT
USED
NOT
USED
3A
3
NOT
USED
7
7A
6
6E
NOT
USED
6
6
6C
6D
6
6
6A
6B
NOT
USED
5A
5
SYS.
DET.
S2
SYS.
DET.
S1
4
4A
4
4B
4
4C
4
4D
4
4E
NOT
USED
SYS.
DET.
S4
SYS.
DET.
S3
8
8E
NOT
USED
8
8
8C
8D
8
8
8A
8B
4 PED
ISOLATOR
DC
2 PED
ISOLATOR
DC
8 PED
ISOLATOR
DC
6 PED
ISOLATOR
DC
PRE = PREEMPT
ISOLATOR
DC
ISOLATOR
DC
PRE3
PRE5
ISOLATOR
DC
ISOLATOR
PRE4
PRE6
DC
ISOLATOR
AC
ISOLATOR
AC
PRE1
PRE2
NOT
USED
3A
3 4
4A
4
4B
8
8
8A
8B
NOT
USED
7
7A
SYS.
DET.
S2
SYS.
DET.
S1
connected to the controller.
harness pin. Neither of the output pins for slot 10 are
pins jumpered together and wired to a single controller
controller. Slots 1, 4, 5 and 8 have the two output
every output terminal is independently connected to the
isolator. Each slot has two output terminals, but not
2-channel inductive loop detector, AC isolator or DC
Each input file has 14 slots. Each slot can hold a
5A 6A
6B
6
6 6/SYS
6C/S3
6D/S4
controller detectors can be easily reassigned as needed.
phase settings should be followed as much as practical,
detector, a system detector, or both. While the default
the lower half. A channel can be assigned to a local
upper half of the block while the loop name is shown in
each channel, the function of the loop is shown in the
detail by a block in the layouts shown on the left. For
channels. Each channel is represented on the electrical
up for inductive loop detector cards. Each card has two
Inductive Loop Detectors - Input file slots 1-9 are set
1 3
8.0
NORTH CAROLINA DEPARTMENT OF TRANSPORTATIONTRANSPORTATION MOBILITY AND SAFETY DIVISION
SIGNALS MANAGEMENT SECTION
pole mounted 336 cabinet has only the ’I’ file.
332 cabinet has two input files, labeled ’I’ and ’J’. The
or other functions deemed necessary. The base mounted
traffic detection, pedestrian pushbuttons, preempt calls
cabinet has one or two input files to accept inputs for
NCDOT uses 2070L controllers in type 170 cabinets. Each
Enable, respectively. Both channels of J11 are spares.
I-File are assigned to Manual Advance and Manual Control
unused. The upper and lower channels of Slot 11 in the
10 is not wired to the controller and is therefore
NCDOT reserves them for system detectors instead. Slot
slot 9 are assigned as local detectors by default, but
Econolite Oasis software. The controller detectors for
correspond to the default input assignments in the
drawings. The functions shown for slots 1-8 and 12-14
example shows how the rack is represented on the start
mounted 332 cabinet are shown left. The upper
Two examples of the input file layout for the base
2070 Input File Layout (332)
2-12