2007-2008 Ducati Monster S4R/S - Dynojet...
Transcript of 2007-2008 Ducati Monster S4R/S - Dynojet...
i733-411 www.powercommander.com 2007-2008 Ducati S4R/S - PCIII USB - 1
2007-2008 Ducati Monster S4R/SInstallation Instructions
Dynojet Research 2191 Mendenhall Drive North Las Vegas, NV 89031 (800) 992-4993 www.powercommander.com
Parts List1 Power Commander1 USB Cable1 CD-ROM1 Installation Guide1 Power Adapter2 Power Commander Decals2 Dynojet Decals4 Zip ties
You can also download the PowerCommander software and latest mapsfrom our web site at:
www.powercommander.com
The ignition MUST be turnedOFF before installation!
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
Button Adjustment Display
Faceplate Buttons
USB PortExpansion Port
i733-411 www.powercommander.com 2007-2008 Ducati S4R/S - PCIII USB - 2
1 Remove the seat and left hand sidepanel.
2 Prop the fuel tank in the uprightposition.
3 Remove the airbox lid by disconnect-ing the two hooks on either side of theairbox (Fig A). Unscrew the bolts oneither side of the rear of the airbox orjust lift up to remove the air box.
4 Disconnect the two hoses going to theairbox.
5 Remove the velocity stacks by turningthem counter-clockwise and lifting up(Fig B).
6 Remove the bolt on the underside ofthe airbox (Fig. C).It may be necessary to drop the radia-tor from it’s upper mounts to accessthis bolt.
7 The airbox can now be moved out ofthe way.
Fig
. A
Fig
. B
Fig
. C
Remove this bolt
Hooks
View from left side of bike
Fig
. E
Fig
. F
i733-411 www.powercommander.com 2007-2008 Ducati S4R/S - PCIII USB - 3
11 Unplug the stock connectors from theinjectors (Fig F). Release the springclips to remove each connector. **Do not discard spring clip.**Do not mix up the stock front andrear connectors.
Fig
. D
Unplug these connectors
9 Using the supplied zip ties secure thePCIII to the left hand frame tube(Fig. E).
10 Secure the PCIII harness to the stockwiring harness using the stock bandclamps.
8 Route the PCIII harness underneaththe left hand frame tube as in FigureD and go towards the front of thebike.PCIII harness
PCIII harness
14 Using the supplied wire tap crimp iton the ORANGE wire of the TPSharness (Fig. J).
15 Connect the GREY wire from thePCIII to the wire tap (Fig. J).It is recommended to use dielectricgrease on these connections.
16 Connect the TPS harness back on tothe throttle body.
Fig
. G
Fig
. J
i733-411 www.powercommander.com
12 Plug the connectors from the PCIII in-line of the stock connectors (Fig G). The ORANGE colored wires from thePCIII go to the front cylinder The YELLOW colored wires go to therear cylinder. Reinstall spring clips.
2007-2008 Ducati S4R/S - PCIII USB - 4
Wire tap
Fig
. H
13 Locate the Throttle Position Sensor.Unplug the stock wiring harness fromthe TPS (Fig. H).This connection is located on the lefthand side of the front throttle body.
Unplug TPS harness
Grey wire from PCIII
17 Attach the ground wire from the PCIIIto the negative side of the battery(Fig. K).
18 Reinstall airbox and bodywork.
Fig
.K
i733-411 www.powercommander.com 2007-2008 Ducati S4R/S - PCIII USB - 5
PCIII ground wire