114A4774 KLIK3U Universal Remote Control Owner's Manualwebwalkway.com/manuals/garage_door.pdfThe...

To prevent possible SERIOUS INJURY or DEATH from a moving gate or door:• ALWAYSkeepremotecontrolsoutofreachofchildren.NEVERpermitchildrentooperate,orplaywithremotecontrol

transmitters.• ActivategateordoorONLYwhenitcanbeseenclearly,isproperlyadjustedandtherearenoobstructionstodoortravel.• ALWAYSkeepgateordoorinsightuntilcompletelyclosed.NEVERpermitanyonetocrosspathofmovinggateordoor.

Universal Remote Control

Read instructions thoroughly BEFORE beginning.

If using the Universal Remote Control with residential door openers, the remote control must be used only with door openers manufactured after 1993 that utilize photoelectric sensors. The photoelectric sensors are always located on or near the bottom of the door track.

STOP

MODEL KLIK3U

TaBLE OF COnTEnTsGeTTInG STaRTed ........................................................................... 2LOCaTe THe PROGRaM/LeaRn BUTTOn ......................................3-7

Chamberlain® products ................................................................ 3Genie® products ............................................................................ 4Linear® products........................................................................... 5Wayne dalton® products .............................................................. 5LiftMaster® products .................................................................... 6Overhead door® products ............................................................ 6Stanley® products ......................................................................... 7

GaRaGe dOOR OPeneRS ..............................................................8-9Programming to a garage door opener with a Program/LeaRn button ................................................................ 8Programming to a Genie® Intellicode® 2 garage door opener ...................................................................... 9

Commercial door Operators .......................................................... 10Programming to a commercial door operator with a Program/LeaRn button ................................................... 10

GaTe OPeRaTORS .....................................................................11-13Program to a gate operator with a Program/LeaRn button ................................................... 11Programming to a GTO/Mighty Mule gate operator without a remote control ............................................ 12Programming to a GTO/Mighty Mule gate operator with a remote control .................................................. 13

exTeRnaL ReCeIveRS ..............................................................14-15Programming to an external receiver with dIP switches ....................................................................... 14Programming to an external receiver with a Program/LeaRn button ................................................... 15

aLTeRnaTe PROGRaMMInG OPTIOnS .....................................16-17alternate programming option for products with a Program/LeaRn button ................................................... 16alternate programming option for products with dIP switches ....................................................................... 17

need HeLP? ................................................................................... 18BaTTeRy ........................................................................................ 19

2

gETTIng sTaRTED

The remote control can be programmed to activate up to two products, such as a garage door opener, gate operator, or commercial door operator. The images throughout this manual are for reference only and your product may look different.

Button 2ProgrammedseparatelyfromButton1.

Garage door Opener Commercial door OperatorGate Operator

Button 1ProgrammedseparatelyfromButton2.

Program Button Usedforprogrammingproducts.

depending on your product, there is a button (Program/LeaRn button) or dIP switches used for programming. you will need to locate the Program/LeaRn button or dIP switches on your product before you start programming.

dIP Switches UsedforprogrammingproductswithDIPswitches.

GaRaGe dOOR OPeneRSTheProgram/LEARNbuttonorDIPswitchesaretypicallylocatedonthebackorsidepanelofyourgaragedooropener.YourProgram/LEARNbuttonmayhaveadifferentname(SMARTbutton,SETbutton,etc.).ForhelplocatingyourProgram/LEARNbuttonorDIPswitchesrefertotheTableofContentsinthismanualorcontactyourgaragedooropenermanufacturer.

COMMeRCIaL dOOR OPeRaTORSTheProgram/LEARNbuttonorDIPswitchesaretypicallylocatedonthelogicboardofyouroperator.YourProgram/LEARNbuttonmayhaveadifferentname(RADIObutton,XMITTERbutton,etc.).ForhelplocatingyourProgram/LEARNbuttonorDIPswitchescontactyourdooroperatormanufacturer.

GaTe OPeRaTORSTheProgram/LEARNbuttonorDIPswitchesaretypicallylocatedonthecontrolboardofyouroperator.YourProgram/LEARNbuttonmayhaveadifferentname(RADIObutton,XMITTERbutton,etc.).ForhelplocatingyourProgram/LEARNbuttonorDIPswitchescontactyourgateoperatormanufacturer.

exTeRnaL ReCeIveRSomeproductsdonothaveaProgram/LEARNbuttonorDIPswitches.Inthiscase,theProgram/LEARNbuttonorDIPswitcheswillbelocatedinanexternalreceiver.Thereceiverwillbelocatedontheproductormountednearby.Followtheprogramminginstructionsforanexternalreceiver.

3

LOCaTE ThE PROgRaM/LEaRn BUTTOn

ChaMBERLaIn PRODUCTs

4


gEnIE PRODUCTs

LearnCodeButton

ProgramSetButton

5


LInEaR PRODUCTs

WaYnE DaLTOn PRODUCTs

LearnButton

LearnButton

ProgramSWButton

6


LIFTMasTER PRODUCTs

OvERhEaD DOOR PRODUCTs

YellowLearnButton

PurpleLearnButton

OrangeLearnButton

GreenLearnButton

LearnCodeButton

7

LOCaTE ThE LEaRn BUTTOn

sTanLEY PRODUCTs

LearnButton

8

gaRagE DOOR OPEnERs

Programming to a garage Door Opener with a Program/LEaRn ButtonThe Program/LeaRn button is typically located on the back or side panel of the garage door opener or an external receiver. For help locating your Program/LeaRn button refer to the Help section in this manual or contact your garage door opener manufacturer. If you have a Genie® Intellicode® 2 garage door opener go to the next page.Theimagesthroughoutthismanualareforreferenceonlyandyourproductmaylookdifferent.

ProgramButton

1 PresstheprogrambuttonontheremotecontroluntiltheLEDturnson.

2 PressandreleasetheProgram/LEARNbutton*onyourgaragedooropener.

3 Pressandreleasetheremotecontrolbutton,theLEDwillflash.WhentheLEDstopsflashing,continuetopressandreleasethebutton(maximumof9times)untilyourgaragedooropenerrespondsbyclicking,blinking,oractivating.

4 Presstheprogrambuttonontheremotecontroltosave.

5 Testtheremotecontrolbypressingthebutton.Ifthegaragedooropenerdoesnotactivate,repeattheprogrammingstepsorfollowthealternativeprogrammingoption.

ProgramButton

*Dependingonyourproduct,theProgram/LEARNbuttonmayhaveadifferentname(usethebuttonforprogrammingremotecontrols).

LED

9

Programming to a genie® Intellicode® 2 garage Door OpenerBefore starting, you MUST have a Genie® Intellicode® 2 remote control with at least one button already programmed to the garage door opener.Theimagesthroughoutthismanualareforreferenceonlyandyourproductmaylookdifferent.

gaRagE DOOR OPEnERs (continued)

1 PresstheprogrambuttonontheUniversal Remote ControluntiltheLEDturnson.

2 Selectabuttontoprogramandpressthatbutton5times,ensuring the LED stops flashing after each press.

3 PresstheprogrambuttonontheUniversal Remote Control.

4 Onthegaragedooropener,pressandholdthe Program/SetbuttonuntilboththelongandshortLEDlightupBLUE.

5 ReleasetheProgram/SetbuttonandonlytheroundLEDwillbelitinBLUE.

6 PressandreleasetheProgram/SetbuttonandthelongLEDwillflashPURPLE.

7 OntheUniversalRemoteControl,pressandreleasethesamebuttonyouhavealreadyselectedinstep2.BothLEDsonthegaragedooropenerwilllightupPURPLE.

8

OntheUniversal Remote Control,pressandreleasethesamebuttonagain.BothLED’sonthegaragedooropenerwilllightupBLUE.

OntheGenie®remotecontrol,pressandreleasethebuttonthatisalreadyprogrammedtothegaragedooropener.BothLED’swillflashPURPLE.

9 OntheUniversal Remote Control,pressandreleasethesamebuttonagain.Thiswillactivatethegaragedooropenerandprogrammingiscomplete.Ifthedoordoesnotactivate,repeatthesteps.

10

ProgramButton

ProgramButton

LED

10

COMMERCIaL DOOR OPERaTORs

Programming to a Commercial Door Operator with a LEaRn ButtonThe Program/LeaRn button is typically located on the logic board of the operator or an external receiver. For help locating your Program/LeaRn button contact your commercial door operator manufacturer. Theimagesthroughoutthismanualareforreferenceonlyandyourproductmaylookdifferent.


2 PressandreleasetheProgram/LEARNbutton*onyourcommercialdooroperator.

3 Pressandreleasetheremotecontrolbutton,theLEDwillflash.WhentheLEDstopsflashing,continuetopressandreleasethebuttonuntilyourcommercialdooroperatorrespondsbyclicking,blinking,oractivating.


5 Testtheremotecontrolbypressingthebutton.Ifthecommercialdooroperatordoesnotactivate,repeattheprogrammingstepsorfollowthealternativeprogrammingoption.

Program/LEARNButton*


ProgramButton

ProgramButton

LED

11

Programming to a gate Operator with a Program/LEaRn ButtonThe Program/LeaRn button is typically located on the control board of the operator or an external receiver. For help locating your Program/LeaRn button contact your gate operator manufacturer.Theimagesthroughoutthismanualareforreferenceonlyandyourproductmaylookdifferent.

gaTE OPERaTORs


2 PressandreleasetheProgram/LEARNbutton*onyourgateoperator.

3 Pressandreleasetheremotecontrolbutton,theLEDwillflash.WhentheLEDstopsflashing,continuetopressandreleasethebuttonuntilyourgateoperatorrespondsbyclicking,blinking,oractivating.


5 Testtheremotecontrolbypressingthebutton.Ifthegateoperatordoesnotactivate,repeattheprogrammingstepsorfollowthealternativeprogrammingoption.

Program/LearnButton*


ProgramButton

ProgramButton

LED

12

Programming to a gTO/Mighty Mule gate Operator without a Remote ControlIf you have an existing GTO remote control go to the next page. Theimagesthroughoutthismanualareforreferenceonlyandyourproductmaylookdifferent.

SettheremotecontrolDIPswitches1-9toanycombination.

gaTE OPERaTORs (continued)


2

3 Pressandreleasetheremotecontrolbutton,theLEDwillflash.WhentheLEDstopsflashing,continuetopressandreleasethebutton20times,ensuring the LED stops flashing after each press.Thecodeisacceptedwhenthegateoperatorisactivated.


5 Programtheremotecontroltothegateoperator(refertothegateoperatorinstructions).

6 Testtheremotecontrolbypressingthebutton.Ifthegateoperatordoesnotactivate,repeattheprogrammingsteps.

ProgramButton

ProgramButton

LED

13

Programming to a gTO/Mighty Mule gate Operator with a Remote Control

gaTE OPERaTORs (continued)

InITIaL sETUP

If you don’t have an existing GTO remote control go to the previous page.Before beginning, check the dIP switches on the GTO remote control. If any of the dIP switches are in the "0" position, move them to either the "+" or "-" position and reprogram the GTO remote control to the gate operator (refer to the gate operator instructions).Theimagesthroughoutthismanualareforreferenceonlyandyourproductmaylookdifferent.

2-BUTTOn GTO ReMOTe COnTROLIftherightbuttonontheGTOremotecontrolisprogrammedtothegateoperator,theGTOremotecontrolwillneedtobereprogrammedusingtheleftbutton.

3-BUTTOn GTO ReMOTe COnTROLIfthemiddlebuttonontheGTOremotecontrolisprogrammedtothegateoperator,theGTOremotecontrolwillneedtobereprogrammedusingeithertheleftorrightbutton.

STOP

nODIPswitchesinthe"0"position

1 MatchtheUniversal Remote ControlDIPswitchestotheGTOremotecontrolDIPswitches: GTO “+” = Universal Remote Control “ON” GTO“-”=UniversalRemoteControl“OFF”

2 2-BUTTOn GTO ReMOTe COnTROLS OnLy:Setthe9thDIPswitchontheUniversal Remote Controltothe“ON”position.3-BUTTOn GTO ReMOTe COnTROLS OnLy:Setthe9thDIPswitchontheUniversal Remote Controltothe“ON”positionifusingtheGTOleftbuttonorthe“OFF”positionifusingtheGTOrightbutton.

3 PresstheprogrambuttonontheUniversal Remote Control untiltheLEDturnson.

4 PressandreleasetheUniversal Remote Controlbutton,theLEDwillflash.WhentheLEDstopsflashing,continuetopressandreleasethebutton20times,ensuring the LED stops flashing after each press.Thecodeisacceptedwhenthegateoperatorisactivated.

5 PresstheprogrambuttonontheUniversal Remote Control tosave.

6 TesttheUniversal Remote Controlbypressingthebutton.Ifthegateoperatordoesnotactivate,repeattheprogrammingsteps.

ProgramButton

ProgramButton

LED

14

Programming to an External Receiver with DIP switches

EXTERnaL RECEIvERs

1 PresstheprogrambuttonontheUniversalRemoteControluntiltheLEDturnson.

2MatchtheDIPswitchesbetweentheexistingremotecontrolorexternalreceiverandtheUniversal Remote Control.TurnextraswitchesOFF.

3

External Receiver

DIPSwitchesDIPSwitches

Existing Remote Universal Remote Control


If using the Universal Remote Control with residential door openers, the remote control must be used only with door openers manufactured after 1993 that utilize photoelectric sensors. The photoelectric sensors are always located on or near the bottom of the door track. The external receiver is typically located on the product or mounted near the product. Theimagesthroughoutthismanualareforreferenceonlyandyourproductmaylookdifferent.

PressandreleasetheUniversalRemoteControlbutton,theLEDwillflash.WhentheLEDstopsflashing,continuetopressandreleasethebuttonuntilyourproductrespondsbyclicking,blinking,oractivating.

4 PresstheprogrambuttonontheUniversalRemoteControltosave.

5 TesttheUniversalRemoteControlbypressingthebutton.Iftheproductdoesnotactivate,repeattheprogrammingstepsorfollowthealternativeprogrammingoption.

STOP

ProgramButton

ProgramButton

LED

3 Position DIP Switch:

For Chamberlain remotes DO NOT use the “0” position, use “+” or “-”. If you already have a 3-button remote, DIP switch #1 must be set to “-” if the large button is to open the door. It may be necessary to reprogram original remote controls.


If programming fails reverse DIP switches (OFF to ON and ON to OFF).

TIPs

15

Programming to an External Receiver with a Program/LEaRn Button

EXTERnaL RECEIvERs (continued)


2 PressandreleasetheProgram/LEARNbutton*ontheexternalreceiver.

3 Pressandreleasetheremotecontrolbutton,theLEDwillflash.WhentheLEDstopsflashing,continuetopressandreleasethebuttonuntilyourproductrespondsbyclicking,blinking,oractivating.


5 Testtheremotecontrolbypressingthebutton.Iftheproductdoesnotactivate,repeattheprogrammingstepsorfollowthealternativeprogrammingoption.

Program/LEARNButton*

If using the Universal Remote Control with residential door openers, the remote control must be used only with door openers manufactured after 1993 that utilize photoelectric sensors. The photoelectric sensors are always located on or near the bottom of the door track. The external receiver is typically located on the product or mounted near the product. Theimagesthroughoutthismanualareforreferenceonlyandyourproductmaylookdifferent.

*Dependingonyourproduct,theProgram/SMART/LEARNbuttonmayhaveadifferentname(usethebuttonforprogrammingremotecontrols).

STOP

ProgramButton

ProgramButton

LED

16

alternative programming option for products with a Program/LEaRn ButtonThe Program/LeaRn button is typically located on the product or an external receiver. For help locating your Program/LeaRn button refer to the Help section in this manual or contact your product manufacturer. Theimagesthroughoutthismanualareforreferenceonlyandyourproductmaylookdifferent.

**LiftMaster,Do-It,MasterMechanic,Raynor,TrueValueandSearsCraftsmanarecompatiblewithChamberlaintechnology.

aLTERnaTIvE PROgRaMMIng OPTIOns


2 PressandreleasetheProgram/LEARNbutton*onyourproduct.

3 Pressandreleasetheremotecontrolbutton... ...8 times (Chamberlain®**productwithyellowProgram/LEARNbutton). ...3 times (Chamberlain®**productwithpurple Program/LEARNbutton). ...2 times (Chamberlain®**productwithorangeProgram/LEARNbutton). ...4 times (Chamberlain®**productwithgreen Program/LEARNbutton). ...5 or 6 times (OverheadDoor® Genie® Intellicodeproduct). ...1 time (Linear®Mega-Codeproduct). ...7 times (Stanley®SecureCodeproduct). ...9 times (WayneDalton®RollingCodeproduct).TheLEDontheremotecontrolmuststopblinkingbetweeneachpressofthebutton.Thecodeisacceptedwhentheproductrespondsbyclicking,blinking,oractivating.


5 Testtheremotecontrolbypressingthebutton.Iftheproductdoesnotactivate,repeattheprogrammingsteps.


ProgramButton

ProgramButton

LED

17

alternative programming option for products with DIP switches

aLTERnaTIvE PROgRaMMIng OPTIOns (continued)

PressandreleasetheUniversalRemoteControlbutton... ...11 times (Chamberlain®**productwith9 DIPswitches). ...12 times (Chamberlain®**Canadaproductwith9 DIPswitches). ...13 times (Genie®productwith12 DIPswitches). ...14 times (LinearMulticode®with10 DIPswitches). ...15 times (Chamberlain®*productwith8 DIPswitches). ...16 times (Stanley/Multicode®productwith10 DIPswitches). ...17 times (Genie®productwith9 DIPswitches). ...18 times (Linear®,Moore-O-Matic®productwith8 DIPswitches). ...19 times (Chamberlain®**productwith7 DIPswitches).TheLEDontheUniversalRemoteControlmuststopblinkingbetweeneachpressofthebutton.Thecodeisacceptedwhenthegaragedooropenerrespondsbyclicking,blinking,oractivating.

1 PresstheprogrambuttonontheUniversalRemoteControluntiltheLEDturnson.

2MatchtheDIPswitchesbetweentheexistingremotecontrolorexternalreceiverandtheUniversalRemoteControl.TurnextraswitchesOFF.

3

5 PresstheprogrambuttonontheUniversalRemoteControltosave.

6 TesttheUniversalRemoteControlbypressingthebutton.Iftheproductdoesnotactivate,repeattheprogrammingsteps.

External Receiver

DIPSwitchesDIPSwitches

Existing RemoteUniversal Remote Control

If using the Universal Remote Control with residential door openers, the remote control must be used only with door openers manufactured after 1993 that utilize photoelectric sensors. The photoelectric sensors are always located on or near the bottom of the door track. The dIP switches are typically located on the product or an external receiver. For help locating your dIP switches contact your product manufacturer. Theimagesthroughoutthismanualareforreferenceonlyandyourproductmaylookdifferent.

**LiftMaster,Do-It,MasterMechanic,Raynor,TrueValueandSearsCraftsmanarecompatiblewithChamberlaintechnology.

STOP


ProgramButton

ProgramButton

LED


For Chamberlain remote controls DO NOT use the “0” position, use “+” or “-”. If you already have a 3-button remote, DIP switch #1 must be set to “-” if the large button is to open the door. It may be necessary to reprogram original remote controls.


If programming fails reverse DIP switches (OFF to ON and ON to OFF).

TIPs

18

nEED hELP?

The remote control will not program to a product with dIP switches.• Checkthebatteryintheremotecontrol.TheLEDshouldlightwhenyoupressabutton.Replacethebatteryifnecessary.

• Ifprogrammingwith2positionDIPswitches,reversetheDIPswitches(OFFtoONandONtoOFF),thenrepeattheprogrammingsteps.

• ForChamberlainremotecontrolsDONOTusethe“0”position,use“+”or“-”.Ifyoualreadyhavea3-buttonremote,DIPswitch#1mustbesetto“-”ifthelargebuttonistoopenthedoor.Itmaybenecessarytoreprogramoriginalremotecontrols.

• RepeattheprogrammingstepsbutmakesuretheLEDstopsflashingbetweeneachpressoftheremotecontrolbutton.

• TryprogrammingusingtheAlternativeProgrammingOptionforproductswithaLEARNbutton.

The remote control will not program to a product with a Program/LeaRn button.• Checkthebatteryintheremotecontrol.TheLEDshouldlightwhenyoupressabutton.Replacethebatteryifnecessary.

• RepeattheprogrammingstepsbutmakesuretheLEDstopsflashingbetweeneachpressoftheremotecontrolbutton.

• TryprogrammingusingtheAlternativeProgrammingOptionforproductswithDIPswitches.

The remote control Led will not light or it is dim.• Replacethebattery.

The remote control Led does not activate the product until it is close to the product.• Replacethebattery.

To prevent possible SERIOUS INJURY or DEATH:• NEVER allow small children near batteries.• If battery is swallowed, immediately notify doctor.To reduce risk of fire, explosion or chemical burn:• Replace ONLY with 3V2032 coin batteries.• DO NOT recharge, disassemble, heat above 212°F (100°C)

or incinerate.

NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Chamberlain and LiftMaster are Trademarks of Chamberlain Group. Genie is a Trademark of Overhead Door Corporation. Overhead Door is a Trademark of Overhead Door Corporation. Linear is a Trademark of Linear Corporation. Master Mechanic is a Trademark of TruServ. Sears is a Trademark of Sears & Roebuck. Stanley is a Trademark of The Stanley Works. Wayne Dalton is a trademark of Wayne Dalton Corporation. Do It is a trademark of Do It Best Corporation. Mighty Mule and GTO are trademarks of Nortek Inc.

© 2014, The Chamberlain Group, Inc. All Rights Reserved

114A4774

www.chamberlain.com 1-800-442-1255

Battery

BATTERY

To replace the battery, pry open the cover with visor clip or screwdriver, as shown. Insert batteries positive side up (+).

Dispose of batteries properly.

Replace ONLY with 3V2032 coin batteries.

KLIK3U Universal Remote ControlTable of Contentsgetting startedLocate the PROGRAM/LEARN BUTTONChamberlain productsGENIE productsLINEAR productsWAYNE DALTON productsLiftMaster productsOverhead Door productsStanley products

Programming to a Garage Door Opener with a Program/LEARN ButtonProgramming to a Genie® Intellicode® 2 Garage Door OpenerProgramming to a Commercial Door Operator with a LEARN ButtonProgramming to a Gate Operator with a Program/LEARN ButtonProgramming to a GTO/Mighty Mule Gate Operator without a Remote ControlProgramming to a GTO/Mighty Mule Gate Operator with a Remote ControlProgramming to an External Receiver with DIP SwitchesProgramming to an External Receiver with a Program/LEARN ButtonAlternative programming option for products with a Program/LEARN ButtonAlternative programming option for products with DIP SwitchesNEED HELP?BATTERY

114A4774 KLIK3U Universal Remote Control Owner's Manualwebwalkway.com/manuals/garage_door.pdfThe...

Documents

Transcript of 114A4774 KLIK3U Universal Remote Control Owner's Manualwebwalkway.com/manuals/garage_door.pdfThe...