11-ZXPOS CNT Operation Guide

7/27/2019 11-ZXPOS CNT Operation Guide

http://slidepdf.com/reader/full/11-zxpos-cnt-operation-guide 1/58

ZXPOS CNT Operation guide

ZTE University

XXX Team



Objectives

At the end of this course, you will be able to:

Master the functions of ZXPOS CNT

Master the usage of ZXPOS CNT



Contents

Summarize

Preparation

Coverage test

CS service test

PS service test

HSDPA service test

Indoor coverage test



Summarize

Radio network optimization (RNO) is the important step in network construction.

RNO adjust the planning and design reasonably , improve the network coverage,

increase the network capacity, improve the network service quality and resource

utilization ratio. Make the network operation more stably , and provide excellent

service.

Data collection is the necessary premise of analysis and adjustment. Optimization

data including：Driving test data（DT）,Call quality test data（CQT）,OMC

performance data, Customer’s complains, Alarm data , signaling data and other

data.

ZXPOS CNT ( UMTS Edition， for Short CNT) is the professional network

optimization test software developed by ZTE . CNT helps the RNO engineer to do

the test and analysis. Locate network problem and evaluate network quality and

capacity, constitute the optimization solution.



Contents

Summarize

Preparation

Coverage test

CS service test

PS service test

HSDPA service test




PreparationEdit the site information table

CNT can support Excel format site information table load and unload, the

detailed content you can check the attachment：

The requirement of the site information table, at least must including 9

parameters as follows:



PreparationCreate map and design testing route

2 methods to create map：

1. Import the MapInfo format map

2. Use MapInfo convert JPG or BMP format file to Tab format file.

Steps of convert JPG or BMP format file to Tab format file ：

1. Download the city map via the accessorial software ( for

exampleSupperget2000 series ).

2. Use MapInfo open the map

Figure ①





3.Click <Register> on figure 2 to calibrate the map。

4. Select 3-5 points from Google earth or by GPS test, Click <Add>，Enter the

right longitude and latitude as figure 3 and figure 4.

5.Click <OK>，the software will generate map automatic, then the calibration is

finished.

Figure ②

F i g

ur e

③





Figure ④

Figure ⑤ Method to design the testing route：

Some times you need prepare the testing route at first, The method to design

the route in MapInfo as follows:

1. Open MapInfo, open the map file. Click <New Table>, Create a new layer

on the map layer. The detailed setting see figure 6 and 7.




Method to design the testing route：

Figure ⑧ 4. Now the new layer is displayed in the status bar, Select the drawing tools to design

the testing route. See figure 9.

Figure ⑨

5.Save the route.



Preparation

Here the test equipment is ZTE T6 mobile phone

Double click setup. exe to install.

UE driver installation

UE driver installation:



Preparation

Double click to install.

Software installation

CNT/CAN software installation：



PreparationHardware license driver install and upgrade

Driver install：

First plug the USB dog, if inform “find new hardware”，click <cancel>. Click [ Start

→Program→ZTE WiNOM →ZXPOS CNT-UMTS →Micro Dog Install Driver ], Open the

install window.

Select install USB dog driver to install.



PreparationConnect the equipment

Methods：

The figure shows how to connect the equipment，List the equipment for test, such as

GPS 、 GPS antenna 、 RS-232 cable 、 Test Mobile phone 、 Mobile cable 、 CNT

hardware license、Laptop。



PreparationBuild the test environment

1. Connect all equipment

2. Start the software. In the left of the window, add mobile and GPS.

Parameter description：

Build In：（1）Sim Navigator：Simulate a GPS，when no

GPS connect to computer, software will

simulate a GPS, will generate location

information randomly

（2）Indoor Navigator：If do the indoor test,

selection this option

COM：The port connect the equipmentAPT File：load or unload test data.

CellSite File：load or unload site

information




3.Click[ My computer →Management→ Device management→ port（COM and

LPT）], Check the port information.

4.Right click to detect GPS and UE. Then right click test phone, select<Test

Mode> to active test. Select a folder to save the test data in the pop-

window.




5.Load map and testing route: Click Button to show map window. Click

to add map and testing route.

Notice：If the map file is tab format, you can select Automatic labels on

the Properties window, to show the route name.




6.Load site information.

Click [ File->Load Cell Site„] to load site information.

Notice：Click [ File->Unload Cell Site ] can unload the site information.

If already load site information, then you add other site information

table, former will be unload.




Display style setting：

1.Click button，Set the NB Line and cell site label parameters




Display style setting：

2.Click to set the Theme



Contents

Summarize

Preparation

Coverage test

CS service test

PS service test

HSDPA service test




Coverage testSummarize

The aim of coverage test is to know the cell coverage

range, relationship between capacity and coverage.

Compare different service, it is uplink limited or

downlink limited.

Coverage test including pilot coverage test and traffic

channel coverage test.



Coverage testPilot coverage test

1. Build the test environment, and start record the test data.

2. Click ，Open the pilot set window to test.



Coverage testPilot coverage test

3.Tool bar introduction



Coverage testTest data replay

ZXPOS CNT ( UMTS Edition ) Save the test data as apt format, support data replay.

Click [ File->Open APT… ] , select a file to replay.

You can analyze data, to location the network problem.

Control the replay speed



Contents

Summarize

Preparation

Coverage test

CS service test

PS service test

HSDPA service test




CS service testSummarize

ZXPOS CNT support powerful voice auto-dial test function. The

details as follows:

Powerful service planning sequence function. You can define the

auto-test plan flexibly.Support WCDMA/GSM mode test

Locate the call failure reason through layer 3 message, offer the

call statistic information.

Record the time information during call test.



CS service test

1.Build the test environment, Click [View → Phone→ Voice Call Test]，Start the

voice auto-dial test. See figure A.

2.Setting the parameters on figure B.

Figure A Figure B



CS service test

Parameter description

Plan Name：

Call Number ：Called number

Service Option：Generally, select CS12.2K

Call Pattern：Origination or Termination

Continuous Call：

Redial On Drop：

On Continuous Call mode，

redial after call dropCall Count：

Setup Time：Max time for call setup

Call Time：Conversation duration

Tear Down Time：Time for link release

Idle Time：

Apply：

Ignore：



CS service test

3. After setting the parameter, Click <Apply>，Click <Start Call>，Pop the Call

Statistics window

This window including call procedure, time and statistic information (Call originate, hung-up, air

interface message, status etc.)



CS service test

Call statistic parameter description

Current Call column shows all information as follows:Phone Modal：

Phone State： Service status

Setup Time：

Conversation Time：

Tear Down Time： Idle Time：

Current Plan column shows all the statistic information as

follows:

Call Success： Call success time and ratio

Call Block：Time and ratio

Call Drop：Time and ratioCall Fail：Time and ratio

Link Error：Call error and link fault because of UE link broken

Call Prerelease：

Call Remain：Conversation duration

Call Count： Call times



CS service test

4.In Time Statistics window, record all the time statistic message during

conversation, including access request count, call setup time, call time,teardown time, and Idle time.



Contents

Summarize

Preparation

Coverage test

CS service test

PS service test

HSDPA service test




PS service test

1.Click [View → Phone→ Data Call Test]，Start data service test. See figure A.

2.Setting all the parameter in figure B

Figure A Figure B



PS service test

Plan parameter description

Name：Plan name

Continuous：Whether test continuously

Count：Repeat times；

Duration：Conversation time

Idle Time：Timing interval between to test.

Different service, the parameter is different.

（1）Connection test

Entry：Name of dial-up network，Click to setting.

User Name： Password：

Redial if Drop：

Notice：Connect is not a individual test，it’s used to establish

the dial-up connection automatically. So the engineer don’t

need to dial manually. It’s recommend to be the first test

item.

Used to create a new connection；



PS service test


（2）.PPP service testSetting is the same with connection test.

（3).FTP service test：

Host：

Port：

PASV：Setup the connection on passive mode of notUser Name：

Password：

Anonymous：

Timeout (s)：

Direction: Upload or download

Restore：Restore the connection when it’s fault.

Local File：

Remote File：



PS service test


（4）. Http service test

URL：

Direction: Upload or download

Timeout (s)：

Local File：

（5）.Ping service test

Host：

Packet Size (bytes)：

Timeout (ms)：

Ping Count：

Delay (ms): Timing interval between to test.

、



PS service test

(6)、TCP/UDP service test

Down Link，Up Link：

TCP，UDP：

Server Address：

Port： Datagrams Length (bytes)：

Speed (KBits/s)：


3. Click to add or delete a test plan

Click <Apply>，Then <Start Call>，Pop the Message window, start the test.



PS service test

4.Click <Throughput> to check the throughput, status of data transmit and

statistic message.



PS service test


(1)Color Different to identify different service.

(2)Right click menu

Update 500ms：

Update 1000ms：

Update 1500ms：

Show In Kbytes： Option：Color and style of the throughput line

(3) Transfer information

Service Type：

Status：

Total Data(Kbytes): Totally data size will be transmit.

Load Data(Kbytes)： Transmitted data size.Direction: Upload or download

Percent：Progress

Duration：Transmit duration

Avg Throughput(Kbps)：



PS service test

(4)PPP call information

TotalSended(Kbytes)：

TotalReceived(Kbytes)：

Band Width(Kbps)：

Duration（s）： Call Count：

Success Count：

Fail Count：

Drop Count：




Contents

Summarize

Preparation

Coverage test

CS service test

PS service test

HSDPA service test




HSDPA Service test

HSDPA service test, test equipment must support HSPA function.

1.Build the test environment，Click [View→ Phone→ WCDMA]，Start HSDPA test.



HSDPA Service test

2.Open the window according to the information you want to check.



HSDPA Service test

HSDPA parameter description：

(1)HS-SCCH information



HSDPA Service test


(2)HS-DPCCH information



HSDPA Service test


(3)HS-DSCH DL throughput



HSDPA Service test


(4)HS-DSCH BLER information



HSDPA Service test


(5) HSDPA decode status



Contents

Summarize

Preparation

Coverage test

CS service test

PS service test

HSDPA service test




Indoor coverage testSummarize

Indoor coverage test will record the test data without

GPS. You can input the location information according to

the map information. This function used in the place

that GPS is invalid. Means you can define the test route,

and use the “Click and walk” method to do the test.



Indoor coverage testButton instruction

11-ZXPOS CNT Operation Guide

Documents

Transcript of 11-ZXPOS CNT Operation Guide