0RFND(VVHQWLDOV &XEH - Mocka - Australia...Mocka Essentials 4 Cube 5 6 Fli Four Cube oer so eet stan...
Transcript of 0RFND(VVHQWLDOV &XEH - Mocka - Australia...Mocka Essentials 4 Cube 5 6 Fli Four Cube oer so eet stan...
Phillips & Flathead screwdriver required *We recommend using a Flathead screwdriver to tighten all locking nuts 100% before first use.Please clear any loose wood from the locking nut holes before inserting the nut to ensure it locks 100%.
WARNING: Any furniture that is not anchored to a wall has the potential to tip over in certain circumstances, i.e. if a child attempts to climb up on the furniture or in the event of an earthquake. Accordingly, we recommend that all furniture is anchored to a wall. We supply a free safety wall anchor with all furniture sold and we recommend these are used to prevent your product tipping. The fixing device provided should fit most wall types, but please note that different wall materials may require different fixing devices from
x20
BA
x20
C D
E F G H I J
x8x4
x2
x4
x4 x12x2
x20
8 mm
12 mm
35 mm
x1washer
Z
WallScrew
r/washerscrew
x1
Y
wall anchor
x1
X
SafetyStrap
W
Hardware Supplied
Wall Strap
1mocka.co.nz | mocka.com.au
Mocka Essentials 4 CubeAssembly InstructionsThank you for your purchase. Please follow the instructions below for correct assembly.
1 2
First screw in hardware (B) into side panels [1] and [3]. Slide both panels together with the middle shelves [2] and [4], making sure the grooved ends line up. Insert hardware (A) into the holes on shelves [2] and [4].
Tighten (A) with a screwdriver. Slide cupboard back panel [6] into grooves as shown. Screw hinge pins (F) into the holes in the cupboard door. Lower door into pin hole in shelf [4].
x8
A
B
x8
3
1
4
2
6 7
F
x2
HFB
A
1
2mocka.co.nz | mocka.com.au
Mocka Essentials 4 CubeAssembly Instructions
1 2
First screw in hardware (B) into side panels [1] and [3]. Slide both panels together with the middle shelves [2] and [4], making sure the grooved ends line up. Insert hardware (A) into the holes on shelves [2] and [4].
Tighten (A) with a screwdriver. Slide cupboard back panel [6] into grooves as shown. Screw hinge pins (F) into the holes in the cupboard door. Lower door into pin hole in shelf [4].
x8
A
B
x8
3
1
4
2
6 7
F
x2
HFB
A
1
3 4
Screw in hardware (B) into base panel [8]. Place base panel on top while sliding the ends of (B) into holes on the top of the side panels. Make sure the door hinge pin (F) slots in. Insert and tighten hardware (A) with screwdriver.
Attach feet blocks (D) to base panel using long screws (C) and the pre-drilled holes in the base panel. Fasten clip plate (E) to the cupboard door. Attach the magnetic clip (I) inside the cupboard using screws (G).
C
D
8
Ax6
x1H
E
x1G
I
B
A
3mocka.co.nz | mocka.com.au
Assembly InstructionsMocka Essentials 4 Cube
5 6
Flip Four Cube over so feet stand on the floor. Slide cupboard back panel [6] into grooves as shown. Screw hinge pins (F) into the holes in the cupboard door. Lower door into pin hole in shelf [4].
Screw in hardware (B) into top panel [5]. Place panel on top of side panels while sliding the ends of (B) into the holes. Make sure the door hinge pin (F) also fits ino top panel [5]. Insert and tighten hardware (A).
6
F
x2
HF
5
7
Ax6
B
A
Mocka Essentials 4 CubeAssembly Instructions
4mocka.co.nz | mocka.com.au
Jolt WardrobeASSEMBLY INSTRUCTIONS
5
mocka.co.nz | mocka.com.au
5 6
Flip Four Cube over so feet stand on the floor. Slide cupboard back panel [6] into grooves as shown. Screw hinge pins (F) into the holes in the cupboard door. Lower door into pin hole in shelf [4].
Screw in hardware (B) into top panel [5]. Place panel on top of side panels while sliding the ends of (B) into the holes. Make sure the door hinge pin (F) also fits ino top panel [5]. Insert and tighten hardware (A).
6
F
x2
HF
5
7
Ax6
B
A
7 8
Fasten clip plate (E) to the cupboard door using screws (H). Attach the magnetic clip (I) inside the cupboard using screws (G). Check door closes.
Use stickers (J) to cover the holes where the hardware (A) is used.
x1G
I
x1H
E
Mocka Essentials 4 CubeAssembly Instructions
5mocka.co.nz | mocka.com.au
9 10
Attach the safety strap (W) to the top of the back side of the unit using screw (Y). Tighten with a screwdriver.
Once assembled lift furniture into place, do not drag. Use a drill to create a small hole lining up with the top of the safety strap (W). Fasten to wall using wall anchor (X), washer (Z) and screw. Ensure the unit is balanced and steady before use. You’re done, enjoy!
Wall Mount
Y
W
x1Y
W
WXZ
x1
WasherStrap
wall anchor
wall screw
wall screw
Mocka Essentials 4 CubeAssembly Instructions
6mocka.co.nz | mocka.com.au