Post on 06-May-2015
description
Biodiesel Technical Training Course
BIO 2.1: Understanding Diesel
FuelPresented by the National Biodiesel
Board
National Biodiesel Board
• The National Biodiesel Board (NBB) is the trade association for the U.S. Biodiesel Industry
• Receives funding from 3 sources:– Soybean Check-off program (i.e. farmers)– Government Grants and programs– Biodiesel Producer contributions
• Technical, Regulatory, Marketing and Lobbying• Over $100MM over last 15 years
2
Objectives
• Understand the new face of diesel fuels• What are today’s diesel fuel quality standards• How are these standards set?• How do these fuel standards affect the diesel
engine operation? - performance - emissions - fuel economy
Learning Outcomes
• Understand the ASTM diesel fuel quality parameters• Understand the ASTM biodiesel fuel quality
parameters • Understand the key differences and similarities
between biodiesel and diesel• Understand the importance of biodiesel fuel quality
and the BQ-9000 program
4
Emissions Regulations in the driver’s seat
• The Clean Air Act of 1970 gave EPA broad authority to regulate motor vehicle pollution, and the Agency's emission control policies have become progressively more stringent since the early 1970's.
QuickTime™ and aTIFF (Uncompressed) decompressor
are needed to see this picture.
Diesel Emission Reductions
Fuel technology
Combustion technology
Aftertreatment technology
Fuel system technology
Better understanding of combustion
Alternate Fuels (Biodiesel)Low sulfur De-NOx
DOC
PM trap
Rate controlHigh pressure Multi-injection
EGR technology
Others
Control technology
Technology Pathway
What is Diesel Fuel
Various Petroleum Components:• Paraffins• Isoparaffins• Napthenes• Olefins• Aromatic Hydrocarbons
How is diesel made?
• Petroleum coke is heated up to separate the complex mixture of hydrocarbons into usable products like diesel.
• Each petroleum derived product is distinguished by its boiling point.
• Diesel fuel undergoes a hydro-treating process to remove sulfur.
Typical Refinery Products
Solid Petroleum Coke
1000 + 540 + Asphalt
650 - 1200 340 - 650 Residual Oil
650 - 1000 340 - 540 Lube Oils
350 - 650 180 - 340 #2 Diesel, Furnace Oil
340 - 515 170 - 270 Kerosene, Jet Fuel, #1 Diesel
80 - 40030 - 200Gasoline
-40 - 31 -40 - 0 LPG
Product Boiling RangeDeg. F
Boiling RangeDeg. C
From: Schmidt, G.K. and Forster, E.J., “Modern Refining for Today’s Fuels and Lubricants,” SAE Paper 861176, 1986.
Grades of Diesel Fuel
• 1-D ( S15)• 1-D ( S500)• 1-D (S5000)• 2-D ( S15)• 2-D ( S500)• 2-D (S5000)• 4-D
S15, S500, & S5000 relate to sulfur content
Off-road versus On-road use
Varied in density and viscosity
ASTMAmerican Society of Testing & Materials
Diesel Fuel Specifications and Quality
13
ASTM Specifications for Diesel Fuel -ASTM D 975
Grade Grade Grade Grade Grade Property LS #1 LS #2 No. 1-D No. 2-D No. 4-D Flash point ° , C min 38 52 38 52 55
, Water and sediment % , .vol max 0.05 0.05 0.05 0.05 0.50
., Distillation temp° , 90%C .Min -- 282 -- 282 -- .Max 288 338 288 338 --
, Kinematic Viscosity mm2/ 40s at °C .Min 1.3 1.9 1.3 1.9 5.5 Ma .x 2.4 4.1 2.4 4.1 24.0
,Ramsbottom carbon residue 10%, % , .on mass max 0.15 0.35 0.15 0.35 -- , % , .Ash mass max 0.01 0.01 0.01 0.01 0.10
, % , Sulfur mass max 0.05 0.05 0.50 0.50 2.00 , Copper strip corrosion
3 50Max hours at°C . 3No . 3No . 3No . 3No -- , .Cetane Number min 40 40 40 40 30
One of the following :Properties must be met (1) cetane index 40 40 -- -- -- (2) , Aromaticity % , vol max 35 35 -- -- --
Diesel Fuel Specification ASTM D 975
• Flashpoint• Water and
Sediment• Distillation• Kinematic
Viscosity• Ramsbottom
Carbon Residue• Ash
• Sulfur• Copper Strip
Corrosion• Cetane
Number• Cetane Index• Aromaticity• Cloud Point
Cetane Number
• Measures the readiness of a fuel to auto-ignite.• High cetane means the fuel will ignite quickly at the
conditions in the engine (does not mean the fuel is highly flammable or explosive).
• Most fuels have cetane numbers between 40 and 60.• ASTM D 975 requires a minimum cetane number of 40• Premium Diesel fuel typically has a cetane of 47• ASTM methods are ASTM D-613 (ISO 5165) and D-
6890
Cetane
• Cetane engine shown above from petroleum testing facility• Ignition Delay: the period that occurs between the start of fuel
injection and the start of combustion; the higher the cetane number, the shorter the ignition delay and the better the quality of combustion.
3 PROPANEMETHANOL ETHANOL
8 ISO OCTANE (GASOLINE)
20 CETANE (DIESEL FUEL)
Benzene
Toluene Xylene
Low Cetane Impact
Poor Ignition QualityLong ignition delay
Abnormal CombustionPossible High Combustion Pressure
Increased Engine stressExcessive Engine Knock
Smoke on Cold start
Cetane Index
• Cetane index is used as a substitute for the cetane number.
• The cetane index is calculated based on the fuel's density and boiling range.
• Two methods used ASTM D-976 or D-4737. • Cetane improvers that may be added are not
accounted for in the index
Boiling Point and Volatility
• Diesel fuel volatility needs vary for engine load, size, & speed
• Buses & trucks benefit from more volatile fuel
• ASTM D975 sets a min-max range
• Defines the upper and lower limits for 90% distilled point.
– No. 1 diesel: no lower limit, upper = 288 C– No. 2 diesel: lower limit = 282 C, upper = 338 C.
• 282C - 338C
90% Distillation Temperature
• Volatility or Boiling Point is controlled by the Distillation specification or T90
• Primarily used to separate diesel fuels into different grades. • Limits the amount of wax allowed in No. 1• If distillation temperatures are too low, then the fuel may
have difficulty meeting the flashpoint requirement.• If distillation temperatures are too high, then there is an
increased tendency of the fuel to deposit on the cylinder wall, where it can be swept down past the rings and into the lube oil.
Viscosity
• Low viscosity = power loss, component wear due to injector leaking or injection pump leak-down
• Low viscosity = poor lubrication ability
• High viscosity = Poor fuel dispersion, i.e. improper injector spray pattern
• High viscosity = high pump resistance and early pump failure
• Critical property for fuel injection system performance
• Measured with ASTM D 445.• #1 diesel fuel = 1.3 – 2.4 mm2/s• #2 diesel fuel = 1.9 – 4.1 mm2/s
Carbon Residue
• Measure of a diesel fuel’s tendency to form engine deposit
• Tests basically involve heating a sample of fuel to a temperature where the fuel will pyrolyze (decompose without oxygen), leaving a carbon-rich deposit (about 500°C)
• Test is frequently done on the 10% residue of fuel distillation.
• Limitation is 0.35 mass percent for No. 2 D• Limitation is 0.15 mass percent for No. 1 D
Ramsbottom Carbon Residue
• There are many tests for carbon residue:– Ramsbottom (D 524)– Conradson (D 189)– Micro Method (D 4530)
• Diesel fuel specification requires Ramsbottom• Carbon reside can vary with refinery processes
Sulfur Content• Sulfur can impact engine wear and deposits due
varying levels• Sulfur in diesel will now harm new emission control
devices of 2007 & newer vehicles• Sulfur burns to sulfur dioxide and sulfur trioxide,
which can combine with water to form sulfuric acid.• Small droplets of sulfuric acid and other sulfates
contribute to particulate emissions.• Sulfur is limited by the EPA for both on & off road
diesel fuels: In 1993: Reduced from 5000 ppm to 500 ppmIn 2006: Reduced from 500 ppm to 15 ppm
Sulfur Testing
• ASTM D 129 was traditional method but did not have sensitivity for new low sulfur fuels. (Bomb method)
• ASTM D 2622, X-Ray Spectrometry, is more sensitive but may not be adequate for 15 ppm diesel fuels.
Flashpoint
• Measures the temperature at which the vapors above the liquid can be ignited.
• Primarily used to determine whether a liquid is flammable or combustible
• Flashpoint is important for safety and hazard rating • Both DOT and OSHA say that any liquid with a flash
point below 100F is flammable• ASTM D 93 is most common test for diesel fuels.• Can also be used to identify contamination from other
fuels.• No. 1 = 38°C, No. 2 = 52°C
Flashpoint
Low temperature Operation
• Cloud point is the measurement of low temperate operation
• It dictates the temperature at which fuel first starts to crystallize and wax up when cooled
• Cloud point can predicate fuel filter clogging in some fuel delivery systems, but not all
• Other Low temp tests include:CFPP: Cold Filter Plugging PointLTFT: Low Temperature Flow TestPour Point and Cold Soak Filtration Test
Cloud Point
• No specific value is given in ASTM D975.• Requirements vary depending on geography.• 10th percentile temperature map
corresponds to the minimum temperature that would be reached no more than 3 days out of 30 for the month.
• ASTM D 975 contains similar maps for other low temperature months in the United States.
Ash
• Abrasive Solids• Soluble metallic soaps• Originates from
inorganic fuel components
• D 975 requires ash to be < 0.01%, by mass
• Injector & Fuel pump wear
• Piston and Ring wear• Solids = engine deposits• Low ash lubricating oils
- NEW
Copper Strip Corrosion
• Used to predict problems with copper, brass, or bronze components in a fuel system
• A measure of corrosiveness • Polished copper strip is placed in fuel for 3 hours at
50°C, then cleaned with a solvent and inspected for tarnish or corrosion.
• The strip is given a score between 1 and 4 with subdivisions indicated by letters, i.e. 2c means moderate tarnish with lavender coloring.
• Diesel fuel is allowed to be No. 3, which allows all tarnish but no actual corrosion.
Water and Sediment
• Measures free, not emulsified,
water and insoluble particles.• Uses a centrifuge and cone-shaped
or pear-shaped bottles.• Total volume of water and
sediment must be < 0.05%. (500 ppm)• Contamination issue in supply line• Engine impact: Filter plugging, fuel
injection system wear, and corrosion, and opportunity for microbial growth
Lubricity
• Lubricity test methods are continually improving and being evaluated
• Most common tests available to test lubricity: – SLBOCLE (scuffing load ball on
cylinder lubricity evaluator)• ASTM D 6078-99
– HFRR (high frequency reciprocating rig)
• ASTM D 6079-99• D975 points to the HFRR test• Limitation is 520 micron max of
wear at 60C
SLBOCLE
• SLBOCLE “ Scuffing Load Ball-On Cylinder Lubricity Evaluator”
• Steel ball bearing on a steel rotating-ring• Immersed in the test fluid• Weight is applied until a “scuff” mark is
seen on the rotating ring• Tangential force recorded• High Friction coefficient = scuffing• 3100 grams without scuffing passes the
SLBOCLE. (SWRI)
HFRR
• High Frequency Reciprocating Rig (HFRR)
• A steel ball • Reciprocated (1mm) • 200g load at 50 Hz for 75
minutes• 2 mL of Fuel• Adjust to 25 °C or 60 °C (77
°F or 140 °F– 60°C preferred
• Ball contacts test disk (in fuel)
Enhanced Lubricity
Ultra-low Sulfur Diesel
0100200300400500600700800
0.0 1.0 2.0 3.0 4.0 5.0
Biodiesel Blend (%)
HFRR WSD (micron)
• Equipment benefits– Superior lubricity– B2 has up to 66% more
lubricity than #2 Diesel
• EPA required sulfur reduction in diesel
• No overdosing concerns
Density
• Specific gravity – ratio of the density of the fuel to the density of water.– #1 diesel = 0.81– #2 diesel = 0.840 – 0.855
• API gravity – common in petroleum industry. API = 141.5/SG – 131.5
• Can be one indicator of fuel economy, power, deposits, wear, and exhaust smoke
• For example, a low API (or high density) has bore BTUs/gallon which could improve fuel economy
Energy Content
• Heating value of the fuel
• Not specified by ASTM• Typically expressed as
BTUs/gallon• Engine Manufacturers• Impact fuel ecomony• No. 2 D can vary up 15%
between supplier & season
No. 2 D 130,000 BTUs/gallon
Gasoline 114,200 BTUs/gallon Biodiesel (B100) 120,000 BTUs/gallon
Thermal & Oxidative Stability
• Chemical degradation occurs with contact with oxygen for long periods or at high temperatures.
• Oxidation of diesel fuel can form insolubles and peroxides
• Peroxides increase deposits and gumming on fuel pumps and injection systems
• Filter plugging will also occur• ASTM D975 now specifies a
stability parameter
Diesel Fuel Additives
QuickTime™ and aTIFF (Uncompressed) decompressor
are needed to see this picture.
Recent Changes in Diesel Fuel specification
• Acid Number• Allowance of up to 5 % biodiesel content • Lubricity• Stability
Resources for Diesel Fuel Properties
• ASTM International• EPA, Environmental Protection Agency• Changes in Diesel Fuel• USDA Biodiesel education• Internal Combustion Engine Fundamentals, John B. Heywood,
McGraw Hill, 1988 ISBN 0-07-100499-8• Automotive Fuels Reference Book, Keith Owen, Trevor Coley
SAE, 1995, ISBN 1-56091-589-7
Biodiesel Resources
www.biodiesel.org•Biodiesel Training Toolkit
•News Releases & Information Resources
•Technical Library, Spec Sheets & Videos
•OEM Warranty Positions on Biodiesel
• U.S. Diesel Vehicle List
www.BQ-9000.org •Listing of BQ-9000 Certified Companies
www.biotrucker.com•Listing of BioTrucker retail sites
www.biodieselautomotive.org•Dedicated to information exchange for biodiesel & diesel technicians
45
Thank You!Questions…?
Rachel BurtonOEM Diesel Technician Training Programwrenchwench@blast.comTel: 919-444-3495
Call NBB at 1-800-841-5849Visit www.biodiesel.org
46