Post on 20-Jan-2017
MEDICAL ADVANCED TECHNOLOGY
MEDICAL ADVANCED TECHNOLOGY
MAT GmbH & Co.KGFriedrich-Wöhler Straße 1078576 Emmingen-Liptingen, GermanyPhone: +49 (0)7465 909 188 · Fax : +49 (0)7465 909 024 www.mat-medical.com · info@mat-medical.com
Small fRagment inStRumentSand implantS
2
INSTRUCTIONS FOR USE 3. (gB) Warning: the implants described may only be used in combination with mat products!
OSTEOSYNTHESIS – STEEL IMPLANTS(Bone: plates / Screws / pins / Wires / Clips) non-sterile
IMPLANT MATERIAL:implants made from steel in accordance with iSO 5832 – 1 stainless steel ; iSO 5832 – 9 high nitrogen stainless steel manufactured by mat mediCal ad-VanCed teCHnOlOgY. the surface of these implants is chemically passive: not magnetic. these implants can be combined with the standardised material provided that its composition lies within the analysis stipulated in the ISO 5832 – 1 / ISO 5832 – 9 standard and the required specifications. Material alloys with chrome-nickel (implant steel) components can trigger a so-called chrome-nickel allergy by their nature; there are no other known biocompatible hazards! We would point out that implants only function correctly if the following basic rules are observed:
- When selecting implants (bone: plates / screws / pins wires / clips), care must be taken to choose the appropriate implants on the basis of the weight and level of activity of the patient, and the bone fracture to be treated. - note that by making the correct choice of biomechanics the forces to be transferred by the implants remain low.- extreme deformation of the implants must be avoided; the cautious bending of wires, plates and pins does not, however, lead to implant damage provided it is done with sufficient care.- Repeated deformation should be avoided at all costs as it will fatigue the implant material.- the re-use of implants is absolutely forbidden (single use).- We strongly advise you to inform patients of the advantages and disadvantages of implants.- excessive strain as a result of body weight and the level of activity of the patient should be avoided due to the limited strength of the im plants. failure to observe these precautionary measures can have serious consequences for the healing process.
INDICATIONSthese relate to the current practice of applications of implants in osteosynthesis (e.g. see literature aO/aSif instruments and implantstexhammer*Colton iSBn 3-540-56895-6 / iSBn 0-387-56895-6).
CONTRAINDICATIONSacute and chronic infections; muscle, nerve or vascular diseases that endanger the affected extremity; a lack of bony tissue or poor bone quality (e.g. severe osteoporosis); local bone tumours. Systemic diseases and metabolic disorders; infections and falls; drug dependence; obesity; highly physical activities together with activitiesinvolving extreme vibrations which can lead to overstraining of the implants.
NOTESthe user should record and keep all information provided to the patient. it should be checked before use whether the patient tolerates the material to be implan-ted. the implants described in these instructions for use may only be used (implanted) by surgeons with the appropriate experience.
POSSIBLE NEGATIVE EFFECTS (RISKS)failure of the fracture to heal, allergy to the material, failure of the product (break, bending), bone deformation and refracture, infection.
REMOVAL OF IMPLANTSthe implants are normally removed once the fracture has healed.
CLEANING AND STERILISATION OF UNSTERILE IMPLANTSBefore use, the implants must be sterilised using a validated procedure (autoclaved).
MAT MEDICAL ADVANCED TECHNOLOGY VALIDATED PROCEDURES
STERILISER: Steam autoclave: temperature = 121° to 123° Celsius; pressure = 1-1.2 bar (15 to 17 psi) with an exposure time of at least 30 minutes in the packaged state.
STERILISER:Autoclave with prevacuum: During the prevacuum phase the air is extracted from the chamber before the steam flows in. Standard circulation for packaged objects: 132° to 135° Celsius; pressure = 2 – 3 bar (27 to 30 psi) with an exposure time of at least 4 to 10 minutes.
IMPORTANT NOTES: Every time the implants are used or sterilised you must first check that they function perfectly!in the event of failure to observe these instructions or demonstrable violation, no guarantee or compensation for damages can be provided.
Small fRagment manual fOR uSe 3.
ContactFriedrich-Wöhler-Straße 1078576 Emmingen, Germanyphone +49(0)74 65 / 909188Fax +49(0)74 65 / 909024
Internetinfo@mat-medical.comManual for use under our Hompage:www.mat-medical.com
3
Set-011-0010-002 Small fRagment Set COmplete, inClude inStRumentS and implantS
(Steel Implants are included in Set are manufactured according to Raw-Material Standard ISO 5832-1 and biocompatibility ISO 10993-1)
SET-LISTING-CONTENT PAGE 4 UP TO PAGE 6. STEEL TRAY-011-0010-002 AND SET-011-0010-002
4
Set-011-0010-002 Small fRagment Set COmplete, inClude inStRumentS and implantS
SET - LISTING-CONTENT PAGE 1.: INSTRUMENTS REF.: PRODUCT - DESCRIPTION: PCS.:TRAY-011-0010-002 tray Steel for Small fragment Set (graphic Case) -1-pcs.
005-0210-025 drill Bit-aO Shaft Ø 2.5 mm x l. 110 / 85 mm -2-pcs.
005-0210-035 drill Bit-aO Shaft Ø 3.5 mm x l. 110 / 85 mm -2-pcs.
005-0210-089 Small Countersink Ø 3.5 mm used for Ø 2.7 / Ø 3.5 / Ø 4.0 mm Screws -1-pcs.
005-0211-032 tap aO Shaft Ø 3.5 mm, cortical pitch 1.25 mm used for Ø 3.5 mm cortical Screws -2-pcs.
005-0211-036 tap aO Shaft Ø 4.0 mm with cancellous pitch 1.75 mm used for Ø 4.0 cancellous Screws -2-pcs.
005-0211-043 tap Handle with aO-Quickcoupling -1-pcs.
005-0212-020 drill guide 2.0 mm within 3/1 Hole used for Ø 2.0 mm drill Bit and K-Wire Ø 2.0 mm -1-pcs.
005-0212-027 double drill guide 3.5 mm / 2.5 mm used for tap Ø 3.5 mm and drill Bit Ø 2.5 mm -1-pcs.
005-0212-044 insert drill Sleeve Ø 3.5 mm / Ø 2.5 mm x l. 42 mm used for Ø 3.5 mm Shaft Screws -1-pcs.
005-0214-003 Small Hexagonal Screw driver - aO Shaft Standard (hexagonal flats 2.5 mm) used for Ø 2.7 mm / Ø 3.5 mm / 4.0 mm Screws
005-0222-032 universal drill guide 3.5 mm / 2.5 mm used for tap Ø 3.5 mm and drill Bit Ø 2.5 mm applicable for neutral load and compression position
-1-pcs.
005-0219-004 depth gauge used for Ø 2.7 up to Ø 4.0 mm Screws -1-pcs.
005-0219-039 Sharp Hook, length 155 mm -1-pcs.
005-0229-004 Bending iron for 3.5 mm plates -1-pcs.
005-0229-005 Bending iron for 2.7 mm plates -1-pcs.
005-0229-055 Bending template for Small plates 7 Holes -1-pcs.
005-0229-057 Bending template for Small plates 9 Holes -1-pcs.
009-0390-025 Small Hexagonal Screw driver with Self-Holding Sleeve (hexagonal flats Ø 2.5 mm) used for Ø 3.5 mm / Ø 4.0 mm Screws
-1-pcs.
010-0020-070 Self-Centring Bone Holding forceps, length 150 mm, Jaw 9.0 mm -1-pcs.
010-0020-090 Small fragment Repostion forceps, length 135 mm -1-pcs.
010-0020-092 Repostion forceps with Ratchet fixation, length 145 mm -1-pcs.
010-0020-350 Small Hohmann Retractor 6.0 mmn -1-pcs.
010-0020-352 Small Hohmann Retractor 8.0 mmn -1-pcs.
010-0020-354 Hohmann Retractor with broad Shank -2-pcs.
010-0020-802 periosteal elevator small, straight edge, curved Blade with 6.0 mm -1-pcs.
005-0219-097 Screw forceps -1-pcs.
(Steel Implants are included in Set are manufactured according to Raw-Material Standard ISO 5832-1 and biocompatibility ISO 109933-1)
5
Set-011-0010-002 Small fRagment Set COmplete, inClude inStRumentS and implantS
(Steel Implants are included in Set are manufactured according to Raw-Material Standard ISO 5832-1 and biocompatibility ISO 109933-1)
SET - LISTING- CONTENT PAGE 2.: STEEL IMPLANTS SCREwS AND wASHER
REF.: PRODUCT - DESCRIPTION: PCS.:
Fullthreaded - Cortical Screws Ø 3.5 mm001-0004-010 Ø 3.5 mm x length 10.0 mm -8-pcs.001-0004-012 Ø 3.5 mm x length 12.0 mm -8-pcs.001-0004-014 Ø 3.5 mm x length 14.0 mm -8-pcs.001-0004-016 Ø 3.5 mm x length 16.0 mm -8-pcs.001-0004-018 Ø 3.5 mm x length 18.0 mm -8-pcs.001-0004-020 Ø 3.5 mm x length 20.0 mm -8-pcs.001-0004-022 Ø 3.5 mm x length 22.0 mm -8-pcs.001-0004-024 Ø 3.5 mm x length 24.0 mm -8-pcs.001-0004-026 Ø 3.5 mm x length 26.0 mm -8-pcs.001-0004-028 Ø 3.5 mm x length 28.0 mm -8-pcs.001-0004-032 Ø 3.5 mm x length 32.0 mm -8-pcs.001-0004-036 Ø 3.5 mm x length 36.0 mm -8-pcs.001-0004-040 Ø 3.5 mm x length 40.0 mm -8-pcs.001-0004-045 Ø 3.5 mm x length 45.0 mm -6-pcs.001-0004-050 Ø 3.5 mm x length 50.0 mm -6-pcs.
REF.: Fullthreaded - Cancellous Screws Ø 4.0 mm PCS.:001-0007-014 Ø 4.0 mm x length 14.0 mm -6-pcs.001-0007-016 Ø 4.0 mm x length 16.0 mm -6-pcs.001-0007-018 Ø 4.0 mm x length 18.0 mm -6-pcs.001-0007-020 Ø 4.0 mm x length 20.0 mm -6-pcs.001-0007-022 Ø 4.0 mm x length 22.0 mm -6-pcs.001-0007-024 Ø 4.0 mm x length 24.0 mm -6-pcs.001-0007-026 Ø 4.0 mm x length 26.0 mm -6-pcs.001-0007-028 Ø 4.0 mm x length 28.0 mm -6-pcs.001-0007-030 Ø 4.0 mm x length 30.0 mm -6-pcs.001-0007-032 Ø 4.0 mm x length 32.0 mm -6-pcs.001-0007-035 Ø 4.0 mm x length 35.0 mm -6-pcs.001-0007-040 Ø 4.0 mm x length 40.0 mm -6-pcs.001-0007-045 Ø 4.0 mm x length 45.0 mm -6-pcs.001-0007-050 Ø 4.0 mm x length 50.0 mm -6-pcs.001-0007-055 Ø 4.0 mm x length 55.0 mm -4-pcs.001-0007-060 Ø 4.0 mm x length 60.0 mm -4-pcs.
REF.: Short Threaded Cancellous Screws Ø 4.0 mm PCS.:001-0006-012 Ø 4.0 mm x length 12.0 mm / thread l. 5.0 mm -6-pcs.001-0006-014 Ø 4.0 mm x length 14.0 mm / thread l. 5.0 mm -6-pcs.001-0006-016 Ø 4.0 mm x length 16.0 mm / thread l. 6.0 mm -6-pcs.001-0006-018 Ø 4.0 mm x length 18.0 mm / thread l. 7.0 mm -6-pcs.001-0006-020 Ø 4.0 mm x length 20.0 mm / thread l. 8.0 mm -6-pcs.001-0006-022 Ø 4.0 mm x length 22.0 mm / thread l. 9.0 mm -6-pcs.001-0006-024 Ø 4.0 mm x length 24.0 mm / thread l. 10.0 mm -6-pcs.001-0006-026 Ø 4.0 mm x length 26.0 mm / thread l. 12.0 mm -6-pcs.001-0006-028 Ø 4.0 mm x length 28.0 mm / thread l. 14.0 mm -6-pcs.001-0006-030 Ø 4.0 mm x length 30.0 mm / thread l. 14.0 mm -6-pcs.001-0006-035 Ø 4.0 mm x length 35.0 mm / thread l. 14.0 mm -6-pcs.001-0006-040 Ø 4.0 mm x length 40.0 mm / thread l. 14.0 mm -6-pcs.001-0006-045 Ø 4.0 mm x length 45.0 mm / thread l. 15.0 mm -6-pcs.001-0006-050 Ø 4.0 mm x length 50.0 mm / thread l. 15.0 mm -6-pcs.001-0013-001 Washer for Ø 3.5 mm and Ø 4.0 mm Screws -6-pcs.
6
Set-011-0010-002 Small fRagment Set COmplete, inClude inStRumentS and implantS
SET - LISTING-CONTENT PAGE 3.: STEEL IMPLANTS K-wIRES AND PLATESREF.: PRODUCT - DESCRIPTION: PCS.:
Kirschner wires with Trocar Point and Round Shaft End004-0310-012 K-Wire Ø 1.2 mm x length 150 mm -12-pcs.
004-0310-016 K-Wire Ø 1.6 mm x length 150 mm -12-pcs.
004-0310-020 K-Wire Ø 2.0 mm x length 150 mm -12-pcs.
T-Plates, Right angled used with Ø 3.5 mm / Ø 4.0 mm ScrewsPL-1043-33 3/3 Holes x length 50 mm -1-pcs.
PL-1043-44 4/4 Holes x length 56 mm -1-pcs.
REF.: T-Plates, Oblique angled used with Ø 3.5 mm / Ø 4.0 mm Screws PCS.:PL-1041-33 3/3 Holes x length 52 mm -1-pcs.
PL-1041-53 5/3 Holes x length 74 mm -1-pcs.
REF.: One Third Tubular Plates used with Ø 3.5 mm / Ø 4.0 mm Screws PCS.:PL-1020-02 2 Holes x length 28 mm -1-pcs.
PL-1020-03 3 Holes x length 40 mm -1-pcs.
PL-1020-04 4 Holes x length 52 mm -1-pcs.
PL-1020-05 5 Holes x length 64 mm -1-pcs.
PL-1020-06 6 Holes x length 76 mm -1-pcs.
PL-1020-07 7 Holes x length 88 mm -1-pcs.
PL-1020-08 8 Holes x length 100 mm -1-pcs.
REF.: Cloverleaf Plates used with Ø 3.5 mm / Ø 4.0 mm Screws PCS.:PL-1039-03 3 Holes x length 88 mm -1-pcs.
PL-1039-04 4 Holes x length 104 mm -1-pcs.
REF.: DC-Plates within Dynamic Compression Holes used with Ø 3.5 mm / Ø 4.0 mm Screws PCS.:PL-1017-06 6 Holes x length 74 mm -2-pcs.
PL-1017-07 7 Holes x length 86 mm -2-pcs.
PL-1017-08 8 Holes x length 98 mm -2-pcs.
PL-1017-10 10 Holes x length 122 mm -2-pcs.
(Steel Implants are included in Set are manufactured according to Raw-Material Standard ISO 5832-1 and biocompatibility ISO 109933-1)
Recommended Sterilization Container for Set-011-0010-002
CB-105-135 Container Bottom non perforated 580 x 280 x 138 mm
CL-100-010 Container lid 580 x 280 mm
7
Small fRagment fulltHReaded-CORtiCal SCReWS Ø 3.5 mm
IMPORTANT TECHNICAL DIMENSION:
- Head diameter = 6.0 mm- Hexagonal Socket width = 2.5 mm- thread diameter = 2.4 mm- pitch = 1.25 mm- applicable drill Bit for thread Hole = 2.5 mm- applicable tap = 3.5 mm x 1.25 mm pitch- material = Steel according to iSO 5832-1 and Biocompatibility iSO 10993-1
REF.: COMPLETE LENGTH REF.: COMPLETE LENGTH
001-0004-010 10 mm 001-0004-044 44 mm
001-0004-012 12 mm 001-0004-045 45 mm
001-0004-014 14 mm 001-0004-046 46 mm
001-0004-016 16 mm 001-0004-048 48 mm
001-0004-018 18 mm 001-0004-050 50 mm
001-0004-020 20 mm 001-0004-055 55 mm
001-0004-022 22 mm 001-0004-060 60 mm
001-0004-024 24 mm 001-0004-065 65 mm
001-0004-026 26 mm 001-0004-070 70 mm
001-0004-028 28 mm 001-0004-075 75 mm
001-0004-030 30 mm 001-0004-080 80 mm
001-0004-032 32 mm 001-0004-085 85 mm
001-0004-034 34 mm 001-0004-090 90 mm
001-0004-036 36 mm 001-0004-095 95 mm
001-0004-038 38 mm 001-0004-100 100 mm
001-0004-040 40 mm 001-0004-105 105 mm
001-0004-042 42 mm 001-0004-110 110 mm
8
IMPORTANT TECHNICAL DIMENSION:
- Head diameter = 6.0 mm- Hexagonal Socket width = 2.5 mm- Core diameter = 2.4 mm- thread diameter = 3.5 mm- pitch = 1.25 mm- applicable drill Bit for thread Hole = 2.5 mm- applicable tap = note! tapping is not necessary- material = Steel according to iSO 5832-1 and Biocompatibility iSO 10993-1
Small fRagment fulltHReaded-CORtiCal SCReWS Ø 3.5 mm, Selftapping
REF.: COMPLETE LENGTH REF.: COMPLETE LENGTH
001-0004-010S 10 mm 001-0004-044S 44 mm
001-0004-012S 12 mm 001-0004-045S 45 mm
001-0004-014S 14 mm 001-0004-046S 46 mm
001-0004-016S 16 mm 001-0004-048S 48 mm
001-0004-018S 18 mm 001-0004-050S 50 mm
001-0004-020S 20 mm 001-0004-055S 55 mm
001-0004-022S 22 mm 001-0004-060S 60 mm
001-0004-024S 24 mm 001-0004-065S 65 mm
001-0004-026S 26 mm 001-0004-070S 70 mm
001-0004-028S 28 mm 001-0004-075S 75 mm
001-0004-030S 30 mm 001-0004-080S 80 mm
001-0004-032S 32 mm 001-0004-085S 85 mm
001-0004-034S 34 mm 001-0004-090S 90 mm
001-0004-036S 36 mm 001-0004-095S 95 mm
001-0004-038S 38 mm 001-0004-100S 100 mm
001-0004-040S 40 mm 001-0004-105S 105 mm
001-0004-042S 42 mm 001-0004-110S 110 mm
9
- Head diameter = 6.0 mm- Hexagonal Socket width = 2.5 mm- Core diameter = 1.9 mm- thread diameter = 4.0 mm- pitch = 1.75 mm- applicable drill Bit for thread Hole = 2.5 mm- applicable tap = 4.0 mm x 1.75 mm pitch- material = Steel according to iSO 5832-1 and Biocompatibility iSO 10993-1
Small fRagment fulltHReaded-CanCellOuS SCReWS Ø 4.0 mm
IMPORTANT TECHNICAL DIMENSION:
REF.: COMPLETE LENGTH REF.: COMPLETE LENGTH
001-0007-010 10 mm 001-0007-028 28 mm
001-0007-012 12 mm 001-0007-030 30 mm
001-0007-014 14 mm 001-0007-032 32 mm
001-0007-016 16 mm 001-0007-035 35 mm
001-0007-018 18 mm 001-0007-040 40 mm
001-0007-020 20 mm 001-0007-045 45 mm
001-0007-022 22 mm 001-0007-050 50 mm
001-0007-024 24 mm 001-0007-055 55 mm
001-0007-026 26 mm 001-0007-060 60 mm
10
IMPORTANT TECHNICAL DIMENSION:
- Head diameter = 6.0 mm- Hexagonal Socket width = 2.5 mm- Shaft diameter = 2.4 mm- Core diameter = 1.9 mm- thread diameter = 4.0 mm- pitch = 1.75 mm- applicable drill Bit for thread Hole = 2.5 mm- applicable tap = 4.0 mm x 1.75 mm pitch- material = Steel according to iSO 5832-1 and Biocompatibility iSO 10993-1
REF.: COMPLETE LENGTH THREAD LENGTH
001-0006-010 10 mm 5 mm
001-0006-012 12 mm 5 mm
001-0006-014 14 mm 5 mm
001-0006-016 16 mm 6 mm
001-0006-018 18 mm 7 mm
001-0006-020 20 mm 8 mm
001-0006-022 22 mm 9 mm
001-0006-024 24 mm 10 mm
001-0006-026 26 mm 12 mm
001-0006-028 28 mm 14 mm
001-0006-030 30 mm 14 mm
001-0006-035 35 mm 14 mm
001-0006-040 40 mm 14 mm
001-0006-045 45 mm 15 mm
001-0006-050 50 mm 15 mm
001-0006-055 55 mm 16 mm
001-0006-060 60 mm 16 mm
Small fRagment SHORt tHReaded-CanCellOuS SCReWS Ø 4.0 mm
Small fragment Washer for Ø 3.5 mm and Ø 4.0 mm Screws
material = Steel according to iSO 5832-1 and Biocompatibility iSO 10993-1
Ref. no.: 001-0013-001
11
PROFILE:
- Profile = 3.0 mm- thickness = 10.0 mm- distance between Holes = 12.0 mm and 16.0 mm- material = Steel according to iSO 5832-1 and Biocompatibility iSO 10993-1
REF.: HOLES LENGTH
PL-1017-02 2 26 mm
PL-1017-03 3 38 mm
PL-1017-04 4 50 mm
PL-1017-05 5 62 mm
PL-1017-06 6 74 mm
PL-1017-07 7 86 mm
PL-1017-08 8 98 mm
PL-1017-09 9 110 mm
PL-1017-10 10 122 mm
PL-1017-12 12 146 mm
Small fRagment plateS WitHin dYnamiC COmpReSSiOn HOleS uSed WitH Ø 3.5 mm / 4.0 mm
Screws Applicable for Fixation Ulna and Radius Fractures
12
PROFILE:
- Profile = 1.0 mm- thickness = 9.0 mm- distance between Holes = 12.0 mm and 16.0 mm- material = Steel according to iSO 5832-1 and Biocompatibility iSO 10993-1
REF.: HOLES LENGTH
PL-1020-02 2 28 mm
PL-1020-03 3 40 mm
PL-1020-04 4 52 mm
PL-1020-05 5 64 mm
PL-1020-06 6 76 mm
PL-1020-07 7 88 mm
PL-1020-08 8 100 mm
PL-1020-09 9 112 mm
PL-1020-10 10 124 mm
PL-1020-12 12 148 mm
One - tHiRd tuBulaR plateS uSed WitH Ø 3.5 mm / 4.0 mm SCReWS
Applicable for Fixation Fibula / Middle - Hand - and Middle Foot Fractures
13
PROFILE:
- Profile = 2.8 mm- thickness = 10.0 mm- distance between Holes = 12.0 mm - material = Steel according to iSO 5832-1 and Biocompatibility iSO 10993-1
REF.: HOLES LENGTH
PL-1025-05 5 58 mm
PL-1025-06 6 70 mm
PL-1025-07 7 82 mm
PL-1025-08 8 94 mm
PL-1025-09 9 106 mm
PL-1025-10 10 118 mm
PL-1025-12 12 142 mm
PL-1025-14 14 166 mm
PL-1025-16 16 190 mm
PL-1025-18 18 214 mm
PL-1025-20 20 238 mm
PL-1025-22 22 262 mm
ReCOnStRuCtiOn plateS, StRaigHt WitHin COmpReSSiOn HOleS uSed WitH Ø 3.5 / 4.0 mm SCReWS
Applicable for main fixation in Pelvic and Acetabular Fractures also they may sometimes be used in Fractures of the distal Humeral (dorsallateral aspect), the clavicle and calcanius.
The Plates can be bended in three Dimensions. Note for Caution!By Plate bending, bend the plates not greater than 15° at any one site should be avoided !
14
PROFILE:
- Profile = 3.6 mm- thickness = 10.0 mm- distance between Holes = 12.0 mm- pre- bended Radius = 100.0 mm- material = Steel according to iSO 5832-1 and Biocompatibility iSO 10993-1
REF.: HOLES LENGTH
PL-1026-06 6 70 mm
PL-1026-08 8 94 mm
PL-1026-10 10 118 mm
PL-1026-12 12 142 mm
PL-1026-14 14 166 mm
PL-1026-16 16 190 mm
PL-1026-18 18 214 mm
pRe - Bend ReCOnStRuCtiOn plateS, CuRVed WitHin COmpReSSiOn HOleS uSed WitH Ø 3.5 mm / Ø 4.0 mm SCReWS
Applicable for main fixation in Pelvic and Acetabular Fractures
15
PROFILE:
- thickness (Shaft) = 2.0 mm- thickness in Colverleav Section = 1.2 mm- Broad (Shaft) = 15.2 mm - material = Steel according to iSO 5832-1 and Biocompatibility iSO 10993-1
REF.: HOLES LENGTH
PL-1039-03 3 88 mm
PL-1039-04 4 104 mm
PL-1039-05 5 120 mm
PL-1039-06 6 136 mm
ClOVeRleaf plateS uSed WitH Ø 3.5 / 4.0 mm SCReWS
Applicable for Fixation comminuted Fractures of the distal Tibia to Buttress its medial Side and also can be used for proximal Humeral
16
PROFILE (SHAFT):
- thickness = 1.2 mm- Broad (Shaft) = 11.0 mm - material = Steel according to iSO 5832-1 and Biocompatibility iSO 10993-1
REF.: HOLES (SHAFT) HOLES (HEAD) LENGTH
PL-1043-33 3 3 50 mm
PL-1043-44 4 4 56 mm
PL-1043-53 5 3 67 mm
PL-1043-64 6 4 78 mm
t-plateS, RigHt angled uSed WitH Ø 3.5 / 4.0 mm SCReWS
Applicable for Fixation Fractures volar aspect of the distal Radius Left and Right
17
PROFILE (SHAFT):
- thickness = 1.5 mm- Broad (Shaft) = 10.0 mm - material = Steel according to iSO 5832-1 and Biocompatibility iSO 10993-1
REF.: HOLES HOLES (HEAD) LENGTH
PL-1041-33 3 3 52 mm
PL-1041-43 4 3 63 mm
PL-1041-53 5 3 74 mm
t-plateS, OBliQue angled uSed WitH Ø 3.5 / 4.0 mm SCReWS
Applicable for Fixation Fractures dorsal aspect of the distal Radius Left and Right
18
PROFILE (SHAFT):
- thickness = 1.5 mm- Broad (Shaft) = 8.5 mm - material = Steel according to iSO 5832-1 and Biocompatibility iSO 10993-1
REF.: LENGTH DESCRIPTION
PL-4862-01 73 mm large - plate
PL-4863-01 55 mm Small - plate
CalCaneuS plateS uSed WitH Ø 3.5 / 4.0 mm SCReWS
Applicable for Fixation Fractures of the Left and Right Calcaneus
19
PROFILE (SHAFT):
- thickness = 3.5 mm- Broad (Shaft) = 10.0 mm - material = Steel according to iSO 5832-1 and Biocompatibility iSO 10993-1
REF.: HOLES LENGTH DESCRIPTION
PL-4333-03 3 78 mm left - plate
PL-4333-04 4 87 mm left - plate
PL-4330-03 3 78 mm Right - plate
PL-4330-04 4 87 mm Right - plate
BalzeR ClaViCula HOOK plateS uSed WitH Ø 3.5 / Ø 4.0 mm SCReWS
Applicable for Fixation Clavicula Fractures ( Left and Right Plates )
20
PROFILE (SHAFT):
- thickness = 2.5 mm- Broad (Shaft) = 10.0 mm - distance between Holes = 12.0 mm- material = Steel according to iSO 5832-1 and Biocompatibility iSO 10993-1
REF.: HOLES LENGTH
PL-4334-04 4 85 mm
PL-4334-06 6 109 mm
ClaViCula HOOK plateS, StRaigHt uSed WitH Ø 3.5 / 4.0 mm SCReWS
Applicable for Fixation Clavicula Fractures Left and Right
21
PROFILE (SHAFT):
- thickness = 2.5 mm- Broad (Shaft) = 10.0 mm - distance between Holes = 11.5 mm- material = Steel according to iSO 5832-1 and Biocompatibility iSO 10993-1
anatOmiCal pRe-Bend ClaViCula HOOK plateS uSed WitH Ø 3.5 / 4.0 mm SCReWS
Applicable for Fixation Clavicula Fractures ( Left and Right Plates )
REF.: HOLES LENGTH DESCRIPTION
PL-4331-04 4 85 mm left - plate
PL-4331-05 5 97 mm left - plate
PL-4331-06 6 106 mm left - plate
PL-4331-08 8 128 mm left - plate
PL-4332-04 4 85 mm Right - PlatePL-4332-05 5 97 mm Right - PlatePL-4332-06 6 106 mm Right - PlatePL-4332-08 8 128 mm Right - Plate
22
PROFILE (SHAFT):
- thickness = 2.0 mm- Broad (Shaft) = 10.0 mm - distance between Holes = 12.0 mm- material = Steel according to iSO 5832-1 and Biocompatibility iSO 10993-1
Y - ReCOnStRuCtiOn plateS uSed WitH Ø 3.5 / 4.0 mm SCReWS
Applicable for Fixation Distal Humeral Fractures Left and Right
REF.: HOLES LENGTH
PL-4861-03 3 36 mm
PL-4861-04 4 48 mm
PL-4861-05 5 60 mm
PL-4861-06 6 72 mm
PL-4861-07 7 84 mm
PL-4861-08 8 96 mm
23
005-0210-019 drill Bit - aO Shaft Ø 2.0 mm x length 100 mm / 75 mm
005-0210-020 drill Bit - aO Shaft Ø 2.0 mm x length 125 mm / 100 mm
005-0210-025 drill Bit - aO Shaft Ø 2.5 mm x length 110 mm / 85 mm
005-0210-035 drill Bit - aO Shaft Ø 3.5 mm x length 110 mm / 85 mm
geneRal inStRumentS fOR Small fRagment plate - and SCReW SYStem
005-0210-219 drill Bit - Round Shaft Ø 2.0 mm x length 85 mm / 70 mm
005-0210-225 drill Bit - Round Shaft Ø 2.5 mm x length 95 mm / 80 mm
005-0210-238 drill Bit - Round Shaft Ø 3.5 mm x length 180 mm / 165 mm
005-0211-032 tap - aO Shaft Ø 3.5 mm with cortical pitch 1.25 mm used for Ø 3.5 mm cortical Screw
005-0211-036 tap - aO Shaft Ø 4.0 mm with cancellous pitch 1.75 mm used for Ø 4.0 mmcancellous Screw
005-0210-089 Small Countersink Ø 3.5 mm used for Ø 2.7 mm / Ø 3.5 mm / Ø 4.0 mm Screws
005-0214-003 Small Hexagonal Screw driver - aO Shaft standard ( hexagonal flats 2.5 mm ) usedfor Ø 2.7 mm / Ø 3.5 mm / Ø 4.0 mm Screws
005-0214-005 Small Hexagonal Screw driver - aO Shaft long ( hexagonal flats 2.5 mm ) used forØ 2.7 mm / Ø 3.5 mm / Ø 4.0 mm Screws for use with Self-holding SleeveRef. 009-030-052 and coupling Self-holding Sleeve Ref. 009-390-060 (page no. 24)
24
005-0211-043 tap Handle with aO - Quickcoupling
geneRal inStRumentS fOR Small fRagment plate - and SCReW SYStem
005-0211-044 t-Handle Small with aO - Quickcoupling
MA-30-06-16-1600 t - Handle large with aO - Quickcoupling
25
009-0390-060 Coupling Self-Holding Sleeve for Screw driver Ref. 009-0368-025
009-0390-025 Small Hexagonal Screw driver with Self-Holding Sleeve ( hexagonal flats Ø 2.5 mm ) used for Ø 3.5 mm / Ø 4.0 mm Screws
geneRal inStRumentS fOR Small fRagment plate - and SCReW SYStem
009-0390-052 Self-Holding Sleeve for Screw driver Ref. 009-0390-025
009-0368-025 Small Hexagonal Screw driver for Self-Holding Sleeve ( hexagnonal flats 2.5 mm ) used for Ø 3.5 mm / Ø 4.0 mm Screws
26
geneRal inStRumentS fOR Small fRagment plate - and SCReW SYStem
005-0212-044 insert drill Sleeve Ø 3.5 mm / 2.5 mm x length 42 mm used for Ø 3.5 mm Shaft Screwsfor use with double drill guide 005-0212-027
005-0212-027 double drill guide 3.5 mm / 2.5 mm used for tap Ø 3.5 mm and drill Bit Ø 2.5 mm
005-0212-020 drill guide 2.0 mm within 3 / 1 Hole used for ø 2.0 mm drill Bit and K-Wire ø 2.0 mm
27
005-0222-030 universal drill guide 3.5 mm / 2.5 mm used for tap Ø 3.5 mm and drill Bit Ø 2.5 mm appli-cable for neutral and compression position
geneRal inStRumentS fOR Small fRagment plate - and SCReW SYStem
005-0222-032 universal drill guide 3.5 mm / 2.5 mm used for tap Ø 3.5 mm and drill Bit Ø 2.5 mm appli-cable for neutral load and compression position
005-0221-012 plate articulated tension device with Joint, to tension of 20 mm also can be used as a distractor. Color Scale: yellow up to 500n, green up to 1000n, red over 1000n
005-0219-004 depth gauge used for Ø 2.7 mm up to Ø 4.0 mm Screws
28
005-0221-016 Combination Wrench width across flats 11 mm used for tension device Ref. 005-0221-012
geneRal inStRumentS fOR Small fRagment plate - and SCReW SYStem
010-0020-802 periosteal elevator small, straight edge, curved Blade width 6 mm
010-0020-354 Hohmann Retractor with broad Shank
010-0020-350 Small Hohmann Retractor 6 mm
010-0020-352 Small Hohmann Retractor 8 mm
29
geneRal inStRumentS fOR Small fRagment plate - and SCReW SYStem
005-0219-097 Screw forceps
005-0229-005 Bending iron for 2.7 mm plates
005-0229-004 Bending iron for 3.5 mm plates
005-0229-055 Bending template for Small plates 7 Holes
005-0229-057 Bending template for Small plates 9 Holes
30
005-0219-039 Sharp Hook, length 155 mm
geneRal inStRumentS fOR Small fRagment plate - and SCReW SYStem
110-0171-400 Bending pliers for Reconstruction plates 2.7 mm / 3.5 mm
300-3649-814 Wire Bending pliers
31
geneRal inStRumentS fOR Small fRagment plate - and SCReW SYStem
110-0171-402 Bending iron for Reconstruction plates 3.5 mm / 4.5 mm
300-3650-016 Bending Bolt for K - Wires Ø 1.25 mm up to 2.5 mm
300-0007-430 tC - Wire Cutter 180 mm used for soft Wires Ø 2.0 mm - hard Wire Ø 1.5 mm
32
geneRal inStRumentS fOR Small fRagment plate - and SCReW SYStem
300-0007-434 tC - Wire Cutter 220 mm used for soft Wires Ø 3.0 mm - hard Wire Ø 2.5 mm
300-1833-050 Bending pliers for 2.4 mm up to 4.0 mm plates, length 23.0 cm
300-1833-052 Bending pliers for 1.0 mm up to 2.0 mm plates, lenght 20.0 cm
33
geneRal inStRumentS fOR BOne fRaCtuRe tReatment
300-2430-101 plate Bending press
34
010-0020-090 Small fragment Repostion forceps, length 135 mm
geneRal inStRumentS fOR RepOSitiOn BOne fRaCtuRe tReatment
010-0020-088 Reposition forceps curved with Ratchet fixation, one point tip one one step-pointed tip, length 135 mm
010-0020-092 Reposition forceps with Ratchet fixation, length 145 mm
35
geneRal inStRumentS fOR BOne fRaCtuRe tReatment
INS-8206-00 Verbrügge Bone Holding forceps, length 175 mm
INS-8206-02 Verbrügge Bone Holding forceps, length 250 mm
INS-8206-04 Verbrügge Bone Holding forceps, length 260 mm
INS-8206-06 Verbrügge Bone Holding forceps, length 270 mm
010-0020-070 Self-centering Bone Holding forceps, length 150 mm, Jaw 9 mm
010-0020-072 Size 0 - Self-centering Bone Holding forceps, length 190 mm, extra small Jaw 10 mm
010-0020-074 Size 1 - Self-centering Bone Holding forceps, length 240 mm, small Jaw 10 mm
010-0020-076 Size 2 - Self-centering Bone Holding forceps, length 260 mm, medium Jaw 18 mm
010-0020-078 Size 2 - Self-centering Bone Holding forceps, length 280 mm,large Jaw 23 mm
36
PROFILE:
trocar-Round
- material = Steel according to iSO 5832-1 and Biocompatibility iSO 10993-1
REF.: DIAMETER LENGTH
004-0330-008 Ø 0.8 70 mm
004-0330-010 Ø 1.0 70 mm
004-0330-012 Ø 1.2 70 mm
004-0330-014 Ø 1.4 70 mm
004-0330-015 Ø 1.5 70 mm
004-0330-016 Ø 1.6 70 mm
004-0330-018 Ø 1.8 70 mm
004-0330-020 Ø 2.0 70 mm
004-0330-022 Ø 2.2 70 mm
004-0330-025 Ø 2.5 70 mm
004-0330-030 Ø 3.0 70 mm
KiRSCHneR - WiReS WitH tROCaR pOint and ROund SHaft end
REF.: DIAMETER LENGTH
004-0310-008 Ø 0.8 150 mm
004-0310-010 Ø 1.0 150 mm
004-0310-012 Ø 1.2 150 mm
004-0310-014 Ø 1.4 150 mm
004-0310-015 Ø 1.5 150 mm
004-0310-016 Ø 1.6 150 mm
004-0310-018 Ø 1.8 150 mm
004-0310-020 Ø 2.0 150 mm
004-0310-022 Ø 2.2 150 mm
004-0310-025 Ø 2.5 150 mm
004-0310-030 Ø 3.0 150 mm
37
KIRSCHNER - wIRES wITH TROCAR POINT AND ROUND SHAFT END
REF.: DIAMETER LENGTH
004-0300-010 Ø 1.0 310 mm
004-0300-012 Ø 1.2 310 mm
004-0300-014 Ø 1.4 310 mm
004-0300-015 Ø 1.5 310 mm
004-0300-016 Ø 1.6 310 mm
004-0300-018 Ø 1.8 310 mm
004-0300-020 Ø 2.0 310 mm
004-0300-022 Ø 2.2 310 mm
004-0300-025 Ø 2.5 310 mm
004-0300-030 Ø 3.0 310 mm
38
trocar-double point
- material = Steel according to iSO 5832-1 and Biocompatibility iSO 10993-1
REF.: DIAMETER LENGTH
004-0610-008 Ø 0.8 150 mm
004-0610-010 Ø 1.0 150 mm
004-0610-012 Ø 1.2 150 mm
004-0610-014 Ø 1.4 150 mm
004-0610-015 Ø 1.5 150 mm
004-0610-016 Ø 1.6 150 mm
004-0610-018 Ø 1.8 150 mm
004-0610-020 Ø 2.0 150 mm
004-0610-022 Ø 2.2 150 mm
004-0610-025 Ø 2.5 150 mm
004-0610-030 Ø 3.0 150 mm
KIRSCHNER - wIRES wITH TROCAR DOUBLE POINT ( BOTH END wITH TROCAR POINT )
REF.: DIAMETER LENGTH
004-0600-010 Ø 1.0 310 mm
004-0600-012 Ø 1.2 310 mm
004-0600-014 Ø 1.4 310 mm
004-0600-015 Ø 1.5 310 mm
004-0600-016 Ø 1.6 310 mm
004-0600-018 Ø 1.8 310 mm
004-0600-020 Ø 2.0 310 mm
004-0600-022 Ø 2.2 310 mm
004-0600-025 Ø 2.5 310 mm
004-0600-030 Ø 3.0 310 mm
PROFILE:
39
trocar-Round, threaded
- material = Steel according to iSO 5832-1 and Biocompatibility iSO 10993-1
REF.: DIAMETER LENGTH THREADED LENGTH
004-0740-0161 Ø 1.6 150 mm 5
004-0740-0162 Ø 1.6 150 mm 15
004-0740-0163 Ø 2.0 150 mm 15
004-0740-0164 Ø 2.0 200 mm 15
004-0740-0165 Ø 2.5 200 mm 15
004-0740-0166 Ø 2.5 230 mm 20
THREADED KIRSCHNER - wIRES wITH TROCAR POINT AND ROUND END
PROFILE:
MEDICAL ADVANCED TECHNOLOGY
MEDICAL ADVANCED TECHNOLOGY
MAT GmbH & Co.KGFriedrich-Wöhler Straße 1078576 Emmingen-Liptingen, GermanyPhone: +49 (0)7465 909 188 · Fax : +49 (0)7465 909 024 www.mat-medical.com · info@mat-medical.com
Revision 15.01.2013SMALL FRAGMENT © MAT