4 small fragment

MEDICAL ADVANCED TECHNOLOGY


MAT GmbH & Co.KGFriedrich-Wöhler Straße 1078576 Emmingen-Liptingen, GermanyPhone: +49 (0)7465 909 188 · Fax : +49 (0)7465 909 024 www.mat-medical.com · [email protected]

Small fRagment inStRumentSand implantS

2

INSTRUCTIONS FOR USE 3. (gB) Warning: the implants described may only be used in combination with mat products!

OSTEOSYNTHESIS – STEEL IMPLANTS(Bone: plates / Screws / pins / Wires / Clips) non-sterile

IMPLANT MATERIAL:implants made from steel in accordance with iSO 5832 – 1 stainless steel ; iSO 5832 – 9 high nitrogen stainless steel manufactured by mat mediCal ad-VanCed teCHnOlOgY. the surface of these implants is chemically passive: not magnetic. these implants can be combined with the standardised material provided that its composition lies within the analysis stipulated in the ISO 5832 – 1 / ISO 5832 – 9 standard and the required specifications. Material alloys with chrome-nickel (implant steel) components can trigger a so-called chrome-nickel allergy by their nature; there are no other known biocompatible hazards! We would point out that implants only function correctly if the following basic rules are observed:

- When selecting implants (bone: plates / screws / pins wires / clips), care must be taken to choose the appropriate implants on the basis of the weight and level of activity of the patient, and the bone fracture to be treated. - note that by making the correct choice of biomechanics the forces to be transferred by the implants remain low.- extreme deformation of the implants must be avoided; the cautious bending of wires, plates and pins does not, however, lead to implant damage provided it is done with sufficient care.- Repeated deformation should be avoided at all costs as it will fatigue the implant material.- the re-use of implants is absolutely forbidden (single use).- We strongly advise you to inform patients of the advantages and disadvantages of implants.- excessive strain as a result of body weight and the level of activity of the patient should be avoided due to the limited strength of the im plants. failure to observe these precautionary measures can have serious consequences for the healing process.

INDICATIONSthese relate to the current practice of applications of implants in osteosynthesis (e.g. see literature aO/aSif instruments and implantstexhammer*Colton iSBn 3-540-56895-6 / iSBn 0-387-56895-6).

CONTRAINDICATIONSacute and chronic infections; muscle, nerve or vascular diseases that endanger the affected extremity; a lack of bony tissue or poor bone quality (e.g. severe osteoporosis); local bone tumours. Systemic diseases and metabolic disorders; infections and falls; drug dependence; obesity; highly physical activities together with activitiesinvolving extreme vibrations which can lead to overstraining of the implants.

NOTESthe user should record and keep all information provided to the patient. it should be checked before use whether the patient tolerates the material to be implan-ted. the implants described in these instructions for use may only be used (implanted) by surgeons with the appropriate experience.

POSSIBLE NEGATIVE EFFECTS (RISKS)failure of the fracture to heal, allergy to the material, failure of the product (break, bending), bone deformation and refracture, infection.

REMOVAL OF IMPLANTSthe implants are normally removed once the fracture has healed.

CLEANING AND STERILISATION OF UNSTERILE IMPLANTSBefore use, the implants must be sterilised using a validated procedure (autoclaved).

MAT MEDICAL ADVANCED TECHNOLOGY VALIDATED PROCEDURES

STERILISER: Steam autoclave: temperature = 121° to 123° Celsius; pressure = 1-1.2 bar (15 to 17 psi) with an exposure time of at least 30 minutes in the packaged state.

STERILISER:Autoclave with prevacuum: During the prevacuum phase the air is extracted from the chamber before the steam flows in. Standard circulation for packaged objects: 132° to 135° Celsius; pressure = 2 – 3 bar (27 to 30 psi) with an exposure time of at least 4 to 10 minutes.

IMPORTANT NOTES: Every time the implants are used or sterilised you must first check that they function perfectly!in the event of failure to observe these instructions or demonstrable violation, no guarantee or compensation for damages can be provided.

Small fRagment manual fOR uSe 3.

ContactFriedrich-Wöhler-Straße 1078576 Emmingen, Germanyphone +49(0)74 65 / 909188Fax +49(0)74 65 / 909024

[email protected] for use under our Hompage:www.mat-medical.com

3

Set-011-0010-002 Small fRagment Set COmplete, inClude inStRumentS and implantS

(Steel Implants are included in Set are manufactured according to Raw-Material Standard ISO 5832-1 and biocompatibility ISO 10993-1)

SET-LISTING-CONTENT PAGE 4 UP TO PAGE 6. STEEL TRAY-011-0010-002 AND SET-011-0010-002

4


SET - LISTING-CONTENT PAGE 1.: INSTRUMENTS REF.: PRODUCT - DESCRIPTION: PCS.:TRAY-011-0010-002 tray Steel for Small fragment Set (graphic Case) -1-pcs.

005-0210-025 drill Bit-aO Shaft Ø 2.5 mm x l. 110 / 85 mm -2-pcs.

005-0210-035 drill Bit-aO Shaft Ø 3.5 mm x l. 110 / 85 mm -2-pcs.

005-0210-089 Small Countersink Ø 3.5 mm used for Ø 2.7 / Ø 3.5 / Ø 4.0 mm Screws -1-pcs.

005-0211-032 tap aO Shaft Ø 3.5 mm, cortical pitch 1.25 mm used for Ø 3.5 mm cortical Screws -2-pcs.

005-0211-036 tap aO Shaft Ø 4.0 mm with cancellous pitch 1.75 mm used for Ø 4.0 cancellous Screws -2-pcs.

005-0211-043 tap Handle with aO-Quickcoupling -1-pcs.

005-0212-020 drill guide 2.0 mm within 3/1 Hole used for Ø 2.0 mm drill Bit and K-Wire Ø 2.0 mm -1-pcs.

005-0212-027 double drill guide 3.5 mm / 2.5 mm used for tap Ø 3.5 mm and drill Bit Ø 2.5 mm -1-pcs.

005-0212-044 insert drill Sleeve Ø 3.5 mm / Ø 2.5 mm x l. 42 mm used for Ø 3.5 mm Shaft Screws -1-pcs.

005-0214-003 Small Hexagonal Screw driver - aO Shaft Standard (hexagonal flats 2.5 mm) used for Ø 2.7 mm / Ø 3.5 mm / 4.0 mm Screws

005-0222-032 universal drill guide 3.5 mm / 2.5 mm used for tap Ø 3.5 mm and drill Bit Ø 2.5 mm applicable for neutral load and compression position

-1-pcs.

005-0219-004 depth gauge used for Ø 2.7 up to Ø 4.0 mm Screws -1-pcs.

005-0219-039 Sharp Hook, length 155 mm -1-pcs.

005-0229-004 Bending iron for 3.5 mm plates -1-pcs.

005-0229-005 Bending iron for 2.7 mm plates -1-pcs.

005-0229-055 Bending template for Small plates 7 Holes -1-pcs.

005-0229-057 Bending template for Small plates 9 Holes -1-pcs.

009-0390-025 Small Hexagonal Screw driver with Self-Holding Sleeve (hexagonal flats Ø 2.5 mm) used for Ø 3.5 mm / Ø 4.0 mm Screws

-1-pcs.

010-0020-070 Self-Centring Bone Holding forceps, length 150 mm, Jaw 9.0 mm -1-pcs.

010-0020-090 Small fragment Repostion forceps, length 135 mm -1-pcs.

010-0020-092 Repostion forceps with Ratchet fixation, length 145 mm -1-pcs.

010-0020-350 Small Hohmann Retractor 6.0 mmn -1-pcs.

010-0020-352 Small Hohmann Retractor 8.0 mmn -1-pcs.

010-0020-354 Hohmann Retractor with broad Shank -2-pcs.

010-0020-802 periosteal elevator small, straight edge, curved Blade with 6.0 mm -1-pcs.

005-0219-097 Screw forceps -1-pcs.


5



SET - LISTING- CONTENT PAGE 2.: STEEL IMPLANTS SCREwS AND wASHER

REF.: PRODUCT - DESCRIPTION: PCS.:

Fullthreaded - Cortical Screws Ø 3.5 mm001-0004-010 Ø 3.5 mm x length 10.0 mm -8-pcs.001-0004-012 Ø 3.5 mm x length 12.0 mm -8-pcs.001-0004-014 Ø 3.5 mm x length 14.0 mm -8-pcs.001-0004-016 Ø 3.5 mm x length 16.0 mm -8-pcs.001-0004-018 Ø 3.5 mm x length 18.0 mm -8-pcs.001-0004-020 Ø 3.5 mm x length 20.0 mm -8-pcs.001-0004-022 Ø 3.5 mm x length 22.0 mm -8-pcs.001-0004-024 Ø 3.5 mm x length 24.0 mm -8-pcs.001-0004-026 Ø 3.5 mm x length 26.0 mm -8-pcs.001-0004-028 Ø 3.5 mm x length 28.0 mm -8-pcs.001-0004-032 Ø 3.5 mm x length 32.0 mm -8-pcs.001-0004-036 Ø 3.5 mm x length 36.0 mm -8-pcs.001-0004-040 Ø 3.5 mm x length 40.0 mm -8-pcs.001-0004-045 Ø 3.5 mm x length 45.0 mm -6-pcs.001-0004-050 Ø 3.5 mm x length 50.0 mm -6-pcs.

REF.: Fullthreaded - Cancellous Screws Ø 4.0 mm PCS.:001-0007-014 Ø 4.0 mm x length 14.0 mm -6-pcs.001-0007-016 Ø 4.0 mm x length 16.0 mm -6-pcs.001-0007-018 Ø 4.0 mm x length 18.0 mm -6-pcs.001-0007-020 Ø 4.0 mm x length 20.0 mm -6-pcs.001-0007-022 Ø 4.0 mm x length 22.0 mm -6-pcs.001-0007-024 Ø 4.0 mm x length 24.0 mm -6-pcs.001-0007-026 Ø 4.0 mm x length 26.0 mm -6-pcs.001-0007-028 Ø 4.0 mm x length 28.0 mm -6-pcs.001-0007-030 Ø 4.0 mm x length 30.0 mm -6-pcs.001-0007-032 Ø 4.0 mm x length 32.0 mm -6-pcs.001-0007-035 Ø 4.0 mm x length 35.0 mm -6-pcs.001-0007-040 Ø 4.0 mm x length 40.0 mm -6-pcs.001-0007-045 Ø 4.0 mm x length 45.0 mm -6-pcs.001-0007-050 Ø 4.0 mm x length 50.0 mm -6-pcs.001-0007-055 Ø 4.0 mm x length 55.0 mm -4-pcs.001-0007-060 Ø 4.0 mm x length 60.0 mm -4-pcs.

REF.: Short Threaded Cancellous Screws Ø 4.0 mm PCS.:001-0006-012 Ø 4.0 mm x length 12.0 mm / thread l. 5.0 mm -6-pcs.001-0006-014 Ø 4.0 mm x length 14.0 mm / thread l. 5.0 mm -6-pcs.001-0006-016 Ø 4.0 mm x length 16.0 mm / thread l. 6.0 mm -6-pcs.001-0006-018 Ø 4.0 mm x length 18.0 mm / thread l. 7.0 mm -6-pcs.001-0006-020 Ø 4.0 mm x length 20.0 mm / thread l. 8.0 mm -6-pcs.001-0006-022 Ø 4.0 mm x length 22.0 mm / thread l. 9.0 mm -6-pcs.001-0006-024 Ø 4.0 mm x length 24.0 mm / thread l. 10.0 mm -6-pcs.001-0006-026 Ø 4.0 mm x length 26.0 mm / thread l. 12.0 mm -6-pcs.001-0006-028 Ø 4.0 mm x length 28.0 mm / thread l. 14.0 mm -6-pcs.001-0006-030 Ø 4.0 mm x length 30.0 mm / thread l. 14.0 mm -6-pcs.001-0006-035 Ø 4.0 mm x length 35.0 mm / thread l. 14.0 mm -6-pcs.001-0006-040 Ø 4.0 mm x length 40.0 mm / thread l. 14.0 mm -6-pcs.001-0006-045 Ø 4.0 mm x length 45.0 mm / thread l. 15.0 mm -6-pcs.001-0006-050 Ø 4.0 mm x length 50.0 mm / thread l. 15.0 mm -6-pcs.001-0013-001 Washer for Ø 3.5 mm and Ø 4.0 mm Screws -6-pcs.

6


SET - LISTING-CONTENT PAGE 3.: STEEL IMPLANTS K-wIRES AND PLATESREF.: PRODUCT - DESCRIPTION: PCS.:

Kirschner wires with Trocar Point and Round Shaft End004-0310-012 K-Wire Ø 1.2 mm x length 150 mm -12-pcs.

004-0310-016 K-Wire Ø 1.6 mm x length 150 mm -12-pcs.

004-0310-020 K-Wire Ø 2.0 mm x length 150 mm -12-pcs.

T-Plates, Right angled used with Ø 3.5 mm / Ø 4.0 mm ScrewsPL-1043-33 3/3 Holes x length 50 mm -1-pcs.

PL-1043-44 4/4 Holes x length 56 mm -1-pcs.

REF.: T-Plates, Oblique angled used with Ø 3.5 mm / Ø 4.0 mm Screws PCS.:PL-1041-33 3/3 Holes x length 52 mm -1-pcs.

PL-1041-53 5/3 Holes x length 74 mm -1-pcs.

REF.: One Third Tubular Plates used with Ø 3.5 mm / Ø 4.0 mm Screws PCS.:PL-1020-02 2 Holes x length 28 mm -1-pcs.

PL-1020-03 3 Holes x length 40 mm -1-pcs.






REF.: Cloverleaf Plates used with Ø 3.5 mm / Ø 4.0 mm Screws PCS.:PL-1039-03 3 Holes x length 88 mm -1-pcs.


REF.: DC-Plates within Dynamic Compression Holes used with Ø 3.5 mm / Ø 4.0 mm Screws PCS.:PL-1017-06 6 Holes x length 74 mm -2-pcs.





Recommended Sterilization Container for Set-011-0010-002

CB-105-135 Container Bottom non perforated 580 x 280 x 138 mm

CL-100-010 Container lid 580 x 280 mm

7

Small fRagment fulltHReaded-CORtiCal SCReWS Ø 3.5 mm

IMPORTANT TECHNICAL DIMENSION:

- Head diameter = 6.0 mm- Hexagonal Socket width = 2.5 mm- thread diameter = 2.4 mm- pitch = 1.25 mm- applicable drill Bit for thread Hole = 2.5 mm- applicable tap = 3.5 mm x 1.25 mm pitch- material = Steel according to iSO 5832-1 and Biocompatibility iSO 10993-1

REF.: COMPLETE LENGTH REF.: COMPLETE LENGTH

001-0004-010 10 mm 001-0004-044 44 mm

001-0004-012 12 mm 001-0004-045 45 mm

001-0004-014 14 mm 001-0004-046 46 mm

001-0004-016 16 mm 001-0004-048 48 mm

001-0004-018 18 mm 001-0004-050 50 mm

001-0004-020 20 mm 001-0004-055 55 mm

001-0004-022 22 mm 001-0004-060 60 mm

001-0004-024 24 mm 001-0004-065 65 mm

001-0004-026 26 mm 001-0004-070 70 mm

001-0004-028 28 mm 001-0004-075 75 mm

001-0004-030 30 mm 001-0004-080 80 mm

001-0004-032 32 mm 001-0004-085 85 mm

001-0004-034 34 mm 001-0004-090 90 mm

001-0004-036 36 mm 001-0004-095 95 mm

001-0004-038 38 mm 001-0004-100 100 mm

001-0004-040 40 mm 001-0004-105 105 mm

001-0004-042 42 mm 001-0004-110 110 mm

8


- Head diameter = 6.0 mm- Hexagonal Socket width = 2.5 mm- Core diameter = 2.4 mm- thread diameter = 3.5 mm- pitch = 1.25 mm- applicable drill Bit for thread Hole = 2.5 mm- applicable tap = note! tapping is not necessary- material = Steel according to iSO 5832-1 and Biocompatibility iSO 10993-1

Small fRagment fulltHReaded-CORtiCal SCReWS Ø 3.5 mm, Selftapping


001-0004-010S 10 mm 001-0004-044S 44 mm

001-0004-012S 12 mm 001-0004-045S 45 mm

001-0004-014S 14 mm 001-0004-046S 46 mm

001-0004-016S 16 mm 001-0004-048S 48 mm

001-0004-018S 18 mm 001-0004-050S 50 mm

001-0004-020S 20 mm 001-0004-055S 55 mm

001-0004-022S 22 mm 001-0004-060S 60 mm

001-0004-024S 24 mm 001-0004-065S 65 mm

001-0004-026S 26 mm 001-0004-070S 70 mm

001-0004-028S 28 mm 001-0004-075S 75 mm

001-0004-030S 30 mm 001-0004-080S 80 mm

001-0004-032S 32 mm 001-0004-085S 85 mm

001-0004-034S 34 mm 001-0004-090S 90 mm

001-0004-036S 36 mm 001-0004-095S 95 mm

001-0004-038S 38 mm 001-0004-100S 100 mm

001-0004-040S 40 mm 001-0004-105S 105 mm

001-0004-042S 42 mm 001-0004-110S 110 mm

9

- Head diameter = 6.0 mm- Hexagonal Socket width = 2.5 mm- Core diameter = 1.9 mm- thread diameter = 4.0 mm- pitch = 1.75 mm- applicable drill Bit for thread Hole = 2.5 mm- applicable tap = 4.0 mm x 1.75 mm pitch- material = Steel according to iSO 5832-1 and Biocompatibility iSO 10993-1

Small fRagment fulltHReaded-CanCellOuS SCReWS Ø 4.0 mm



001-0007-010 10 mm 001-0007-028 28 mm

001-0007-012 12 mm 001-0007-030 30 mm

001-0007-014 14 mm 001-0007-032 32 mm

001-0007-016 16 mm 001-0007-035 35 mm

001-0007-018 18 mm 001-0007-040 40 mm

001-0007-020 20 mm 001-0007-045 45 mm

001-0007-022 22 mm 001-0007-050 50 mm

001-0007-024 24 mm 001-0007-055 55 mm

001-0007-026 26 mm 001-0007-060 60 mm

10


- Head diameter = 6.0 mm- Hexagonal Socket width = 2.5 mm- Shaft diameter = 2.4 mm- Core diameter = 1.9 mm- thread diameter = 4.0 mm- pitch = 1.75 mm- applicable drill Bit for thread Hole = 2.5 mm- applicable tap = 4.0 mm x 1.75 mm pitch- material = Steel according to iSO 5832-1 and Biocompatibility iSO 10993-1

REF.: COMPLETE LENGTH THREAD LENGTH

001-0006-010 10 mm 5 mm

001-0006-012 12 mm 5 mm

001-0006-014 14 mm 5 mm

001-0006-016 16 mm 6 mm

001-0006-018 18 mm 7 mm

001-0006-020 20 mm 8 mm

001-0006-022 22 mm 9 mm

001-0006-024 24 mm 10 mm

001-0006-026 26 mm 12 mm

001-0006-028 28 mm 14 mm

001-0006-030 30 mm 14 mm

001-0006-035 35 mm 14 mm

001-0006-040 40 mm 14 mm

001-0006-045 45 mm 15 mm

001-0006-050 50 mm 15 mm

001-0006-055 55 mm 16 mm

001-0006-060 60 mm 16 mm

Small fRagment SHORt tHReaded-CanCellOuS SCReWS Ø 4.0 mm

Small fragment Washer for Ø 3.5 mm and Ø 4.0 mm Screws

material = Steel according to iSO 5832-1 and Biocompatibility iSO 10993-1

Ref. no.: 001-0013-001

11

PROFILE:

- Profile = 3.0 mm- thickness = 10.0 mm- distance between Holes = 12.0 mm and 16.0 mm- material = Steel according to iSO 5832-1 and Biocompatibility iSO 10993-1

REF.: HOLES LENGTH

PL-1017-02 2 26 mm

PL-1017-03 3 38 mm

PL-1017-04 4 50 mm

PL-1017-05 5 62 mm

PL-1017-06 6 74 mm

PL-1017-07 7 86 mm

PL-1017-08 8 98 mm

PL-1017-09 9 110 mm

PL-1017-10 10 122 mm

PL-1017-12 12 146 mm

Small fRagment plateS WitHin dYnamiC COmpReSSiOn HOleS uSed WitH Ø 3.5 mm / 4.0 mm

Screws Applicable for Fixation Ulna and Radius Fractures

12

PROFILE:

- Profile = 1.0 mm- thickness = 9.0 mm- distance between Holes = 12.0 mm and 16.0 mm- material = Steel according to iSO 5832-1 and Biocompatibility iSO 10993-1

REF.: HOLES LENGTH

PL-1020-02 2 28 mm

PL-1020-03 3 40 mm

PL-1020-04 4 52 mm

PL-1020-05 5 64 mm

PL-1020-06 6 76 mm

PL-1020-07 7 88 mm

PL-1020-08 8 100 mm

PL-1020-09 9 112 mm

PL-1020-10 10 124 mm

PL-1020-12 12 148 mm

One - tHiRd tuBulaR plateS uSed WitH Ø 3.5 mm / 4.0 mm SCReWS

Applicable for Fixation Fibula / Middle - Hand - and Middle Foot Fractures

13

PROFILE:

- Profile = 2.8 mm- thickness = 10.0 mm- distance between Holes = 12.0 mm - material = Steel according to iSO 5832-1 and Biocompatibility iSO 10993-1

REF.: HOLES LENGTH

PL-1025-05 5 58 mm

PL-1025-06 6 70 mm

PL-1025-07 7 82 mm

PL-1025-08 8 94 mm

PL-1025-09 9 106 mm

PL-1025-10 10 118 mm

PL-1025-12 12 142 mm

PL-1025-14 14 166 mm

PL-1025-16 16 190 mm

PL-1025-18 18 214 mm

PL-1025-20 20 238 mm

PL-1025-22 22 262 mm

ReCOnStRuCtiOn plateS, StRaigHt WitHin COmpReSSiOn HOleS uSed WitH Ø 3.5 / 4.0 mm SCReWS

Applicable for main fixation in Pelvic and Acetabular Fractures also they may sometimes be used in Fractures of the distal Humeral (dorsallateral aspect), the clavicle and calcanius.

The Plates can be bended in three Dimensions. Note for Caution!By Plate bending, bend the plates not greater than 15° at any one site should be avoided !

14

PROFILE:

- Profile = 3.6 mm- thickness = 10.0 mm- distance between Holes = 12.0 mm- pre- bended Radius = 100.0 mm- material = Steel according to iSO 5832-1 and Biocompatibility iSO 10993-1

REF.: HOLES LENGTH

PL-1026-06 6 70 mm

PL-1026-08 8 94 mm

PL-1026-10 10 118 mm

PL-1026-12 12 142 mm

PL-1026-14 14 166 mm

PL-1026-16 16 190 mm

PL-1026-18 18 214 mm

pRe - Bend ReCOnStRuCtiOn plateS, CuRVed WitHin COmpReSSiOn HOleS uSed WitH Ø 3.5 mm / Ø 4.0 mm SCReWS

Applicable for main fixation in Pelvic and Acetabular Fractures

15

PROFILE:

- thickness (Shaft) = 2.0 mm- thickness in Colverleav Section = 1.2 mm- Broad (Shaft) = 15.2 mm - material = Steel according to iSO 5832-1 and Biocompatibility iSO 10993-1

REF.: HOLES LENGTH

PL-1039-03 3 88 mm

PL-1039-04 4 104 mm

PL-1039-05 5 120 mm

PL-1039-06 6 136 mm

ClOVeRleaf plateS uSed WitH Ø 3.5 / 4.0 mm SCReWS

Applicable for Fixation comminuted Fractures of the distal Tibia to Buttress its medial Side and also can be used for proximal Humeral

16

PROFILE (SHAFT):

- thickness = 1.2 mm- Broad (Shaft) = 11.0 mm - material = Steel according to iSO 5832-1 and Biocompatibility iSO 10993-1

REF.: HOLES (SHAFT) HOLES (HEAD) LENGTH

PL-1043-33 3 3 50 mm

PL-1043-44 4 4 56 mm

PL-1043-53 5 3 67 mm

PL-1043-64 6 4 78 mm

t-plateS, RigHt angled uSed WitH Ø 3.5 / 4.0 mm SCReWS

Applicable for Fixation Fractures volar aspect of the distal Radius Left and Right

17

PROFILE (SHAFT):


REF.: HOLES HOLES (HEAD) LENGTH

PL-1041-33 3 3 52 mm

PL-1041-43 4 3 63 mm

PL-1041-53 5 3 74 mm

t-plateS, OBliQue angled uSed WitH Ø 3.5 / 4.0 mm SCReWS

Applicable for Fixation Fractures dorsal aspect of the distal Radius Left and Right

18

PROFILE (SHAFT):


REF.: LENGTH DESCRIPTION

PL-4862-01 73 mm large - plate

PL-4863-01 55 mm Small - plate

CalCaneuS plateS uSed WitH Ø 3.5 / 4.0 mm SCReWS

Applicable for Fixation Fractures of the Left and Right Calcaneus

19

PROFILE (SHAFT):


REF.: HOLES LENGTH DESCRIPTION

PL-4333-03 3 78 mm left - plate


PL-4330-03 3 78 mm Right - plate

PL-4330-04 4 87 mm Right - plate

BalzeR ClaViCula HOOK plateS uSed WitH Ø 3.5 / Ø 4.0 mm SCReWS

Applicable for Fixation Clavicula Fractures ( Left and Right Plates )

20

PROFILE (SHAFT):

- thickness = 2.5 mm- Broad (Shaft) = 10.0 mm - distance between Holes = 12.0 mm- material = Steel according to iSO 5832-1 and Biocompatibility iSO 10993-1

REF.: HOLES LENGTH

PL-4334-04 4 85 mm

PL-4334-06 6 109 mm

ClaViCula HOOK plateS, StRaigHt uSed WitH Ø 3.5 / 4.0 mm SCReWS

Applicable for Fixation Clavicula Fractures Left and Right

21

PROFILE (SHAFT):


anatOmiCal pRe-Bend ClaViCula HOOK plateS uSed WitH Ø 3.5 / 4.0 mm SCReWS

Applicable for Fixation Clavicula Fractures ( Left and Right Plates )

REF.: HOLES LENGTH DESCRIPTION





PL-4332-04 4 85 mm Right - PlatePL-4332-05 5 97 mm Right - PlatePL-4332-06 6 106 mm Right - PlatePL-4332-08 8 128 mm Right - Plate

22

PROFILE (SHAFT):


Y - ReCOnStRuCtiOn plateS uSed WitH Ø 3.5 / 4.0 mm SCReWS

Applicable for Fixation Distal Humeral Fractures Left and Right

REF.: HOLES LENGTH

PL-4861-03 3 36 mm

PL-4861-04 4 48 mm

PL-4861-05 5 60 mm

PL-4861-06 6 72 mm

PL-4861-07 7 84 mm

PL-4861-08 8 96 mm

23

005-0210-019 drill Bit - aO Shaft Ø 2.0 mm x length 100 mm / 75 mm




geneRal inStRumentS fOR Small fRagment plate - and SCReW SYStem

005-0210-219 drill Bit - Round Shaft Ø 2.0 mm x length 85 mm / 70 mm



005-0211-032 tap - aO Shaft Ø 3.5 mm with cortical pitch 1.25 mm used for Ø 3.5 mm cortical Screw

005-0211-036 tap - aO Shaft Ø 4.0 mm with cancellous pitch 1.75 mm used for Ø 4.0 mmcancellous Screw

005-0210-089 Small Countersink Ø 3.5 mm used for Ø 2.7 mm / Ø 3.5 mm / Ø 4.0 mm Screws

005-0214-003 Small Hexagonal Screw driver - aO Shaft standard ( hexagonal flats 2.5 mm ) usedfor Ø 2.7 mm / Ø 3.5 mm / Ø 4.0 mm Screws

005-0214-005 Small Hexagonal Screw driver - aO Shaft long ( hexagonal flats 2.5 mm ) used forØ 2.7 mm / Ø 3.5 mm / Ø 4.0 mm Screws for use with Self-holding SleeveRef. 009-030-052 and coupling Self-holding Sleeve Ref. 009-390-060 (page no. 24)

24

005-0211-043 tap Handle with aO - Quickcoupling


005-0211-044 t-Handle Small with aO - Quickcoupling

MA-30-06-16-1600 t - Handle large with aO - Quickcoupling

25

009-0390-060 Coupling Self-Holding Sleeve for Screw driver Ref. 009-0368-025

009-0390-025 Small Hexagonal Screw driver with Self-Holding Sleeve ( hexagonal flats Ø 2.5 mm ) used for Ø 3.5 mm / Ø 4.0 mm Screws


009-0390-052 Self-Holding Sleeve for Screw driver Ref. 009-0390-025

009-0368-025 Small Hexagonal Screw driver for Self-Holding Sleeve ( hexagnonal flats 2.5 mm ) used for Ø 3.5 mm / Ø 4.0 mm Screws

26


005-0212-044 insert drill Sleeve Ø 3.5 mm / 2.5 mm x length 42 mm used for Ø 3.5 mm Shaft Screwsfor use with double drill guide 005-0212-027

005-0212-027 double drill guide 3.5 mm / 2.5 mm used for tap Ø 3.5 mm and drill Bit Ø 2.5 mm

005-0212-020 drill guide 2.0 mm within 3 / 1 Hole used for ø 2.0 mm drill Bit and K-Wire ø 2.0 mm

27

005-0222-030 universal drill guide 3.5 mm / 2.5 mm used for tap Ø 3.5 mm and drill Bit Ø 2.5 mm appli-cable for neutral and compression position


005-0222-032 universal drill guide 3.5 mm / 2.5 mm used for tap Ø 3.5 mm and drill Bit Ø 2.5 mm appli-cable for neutral load and compression position

005-0221-012 plate articulated tension device with Joint, to tension of 20 mm also can be used as a distractor. Color Scale: yellow up to 500n, green up to 1000n, red over 1000n

005-0219-004 depth gauge used for Ø 2.7 mm up to Ø 4.0 mm Screws

28

005-0221-016 Combination Wrench width across flats 11 mm used for tension device Ref. 005-0221-012


010-0020-802 periosteal elevator small, straight edge, curved Blade width 6 mm

010-0020-354 Hohmann Retractor with broad Shank

010-0020-350 Small Hohmann Retractor 6 mm

010-0020-352 Small Hohmann Retractor 8 mm

29


005-0219-097 Screw forceps

005-0229-005 Bending iron for 2.7 mm plates

005-0229-004 Bending iron for 3.5 mm plates

005-0229-055 Bending template for Small plates 7 Holes

005-0229-057 Bending template for Small plates 9 Holes

30

005-0219-039 Sharp Hook, length 155 mm


110-0171-400 Bending pliers for Reconstruction plates 2.7 mm / 3.5 mm

300-3649-814 Wire Bending pliers

31


110-0171-402 Bending iron for Reconstruction plates 3.5 mm / 4.5 mm

300-3650-016 Bending Bolt for K - Wires Ø 1.25 mm up to 2.5 mm

300-0007-430 tC - Wire Cutter 180 mm used for soft Wires Ø 2.0 mm - hard Wire Ø 1.5 mm

32


300-0007-434 tC - Wire Cutter 220 mm used for soft Wires Ø 3.0 mm - hard Wire Ø 2.5 mm

300-1833-050 Bending pliers for 2.4 mm up to 4.0 mm plates, length 23.0 cm

300-1833-052 Bending pliers for 1.0 mm up to 2.0 mm plates, lenght 20.0 cm

33

geneRal inStRumentS fOR BOne fRaCtuRe tReatment

300-2430-101 plate Bending press

34

010-0020-090 Small fragment Repostion forceps, length 135 mm

geneRal inStRumentS fOR RepOSitiOn BOne fRaCtuRe tReatment

010-0020-088 Reposition forceps curved with Ratchet fixation, one point tip one one step-pointed tip, length 135 mm

010-0020-092 Reposition forceps with Ratchet fixation, length 145 mm

35

geneRal inStRumentS fOR BOne fRaCtuRe tReatment

INS-8206-00 Verbrügge Bone Holding forceps, length 175 mm




010-0020-070 Self-centering Bone Holding forceps, length 150 mm, Jaw 9 mm

010-0020-072 Size 0 - Self-centering Bone Holding forceps, length 190 mm, extra small Jaw 10 mm

010-0020-074 Size 1 - Self-centering Bone Holding forceps, length 240 mm, small Jaw 10 mm

010-0020-076 Size 2 - Self-centering Bone Holding forceps, length 260 mm, medium Jaw 18 mm

010-0020-078 Size 2 - Self-centering Bone Holding forceps, length 280 mm,large Jaw 23 mm

36

PROFILE:

trocar-Round

- material = Steel according to iSO 5832-1 and Biocompatibility iSO 10993-1

REF.: DIAMETER LENGTH

004-0330-008 Ø 0.8 70 mm

004-0330-010 Ø 1.0 70 mm

004-0330-012 Ø 1.2 70 mm

004-0330-014 Ø 1.4 70 mm

004-0330-015 Ø 1.5 70 mm

004-0330-016 Ø 1.6 70 mm

004-0330-018 Ø 1.8 70 mm

004-0330-020 Ø 2.0 70 mm

004-0330-022 Ø 2.2 70 mm

004-0330-025 Ø 2.5 70 mm

004-0330-030 Ø 3.0 70 mm

KiRSCHneR - WiReS WitH tROCaR pOint and ROund SHaft end


004-0310-008 Ø 0.8 150 mm

004-0310-010 Ø 1.0 150 mm

004-0310-012 Ø 1.2 150 mm

004-0310-014 Ø 1.4 150 mm

004-0310-015 Ø 1.5 150 mm

004-0310-016 Ø 1.6 150 mm

004-0310-018 Ø 1.8 150 mm

004-0310-020 Ø 2.0 150 mm

004-0310-022 Ø 2.2 150 mm

004-0310-025 Ø 2.5 150 mm

004-0310-030 Ø 3.0 150 mm

37

KIRSCHNER - wIRES wITH TROCAR POINT AND ROUND SHAFT END


004-0300-010 Ø 1.0 310 mm

004-0300-012 Ø 1.2 310 mm

004-0300-014 Ø 1.4 310 mm

004-0300-015 Ø 1.5 310 mm

004-0300-016 Ø 1.6 310 mm

004-0300-018 Ø 1.8 310 mm

004-0300-020 Ø 2.0 310 mm

004-0300-022 Ø 2.2 310 mm

004-0300-025 Ø 2.5 310 mm

004-0300-030 Ø 3.0 310 mm

38

trocar-double point



004-0610-008 Ø 0.8 150 mm

004-0610-010 Ø 1.0 150 mm

004-0610-012 Ø 1.2 150 mm

004-0610-014 Ø 1.4 150 mm

004-0610-015 Ø 1.5 150 mm

004-0610-016 Ø 1.6 150 mm

004-0610-018 Ø 1.8 150 mm

004-0610-020 Ø 2.0 150 mm

004-0610-022 Ø 2.2 150 mm

004-0610-025 Ø 2.5 150 mm

004-0610-030 Ø 3.0 150 mm

KIRSCHNER - wIRES wITH TROCAR DOUBLE POINT ( BOTH END wITH TROCAR POINT )


004-0600-010 Ø 1.0 310 mm

004-0600-012 Ø 1.2 310 mm

004-0600-014 Ø 1.4 310 mm

004-0600-015 Ø 1.5 310 mm

004-0600-016 Ø 1.6 310 mm

004-0600-018 Ø 1.8 310 mm

004-0600-020 Ø 2.0 310 mm

004-0600-022 Ø 2.2 310 mm

004-0600-025 Ø 2.5 310 mm

004-0600-030 Ø 3.0 310 mm

PROFILE:

39

trocar-Round, threaded


REF.: DIAMETER LENGTH THREADED LENGTH

004-0740-0161 Ø 1.6 150 mm 5

004-0740-0162 Ø 1.6 150 mm 15

004-0740-0163 Ø 2.0 150 mm 15

004-0740-0164 Ø 2.0 200 mm 15

004-0740-0165 Ø 2.5 200 mm 15

004-0740-0166 Ø 2.5 230 mm 20

THREADED KIRSCHNER - wIRES wITH TROCAR POINT AND ROUND END

PROFILE:



MAT GmbH & Co.KGFriedrich-Wöhler Straße 1078576 Emmingen-Liptingen, GermanyPhone: +49 (0)7465 909 188 · Fax : +49 (0)7465 909 024 www.mat-medical.com · [email protected]

Revision 15.01.2013SMALL FRAGMENT © MAT

4 small fragment

Health & Medicine

Transcript of 4 small fragment