1 / 3
STAMPED CONCRETE APPLICATION
FAST AND EASY
FIRST DAY-STEP 1: First add to concrete mixer Style Beton Fibbers. The fibbers are very strong to acids and to alkalis and perfectly stable to ultraviolet rays, to bacteria and muffs, have a good adhesion to cement thanks to chemical bonds that develop.
FIRST DAY-STEP 2: Reinforce the concrete floor with a metal grid. Ensure reinforcement, inserts, embedded parts, and formed joints are not disturbed during concrete placement.
FIRST DAY-STEP 3: Deposit concrete so that specified slab thickness will be obtained after finishing operations.
2 / 3
FIRST DAY-STEP 4: Make the concrete surface smooth, using a trowel.
FIRST DAY-STEP 5: Make the concrete edges smooth, using hand edger.
FIRST DAY-STEP 6: After the concrete surface is poured and floated, Style Beton Color Hardener, which is a tinted, powdery sub-stance blended of mineral-based pigments, portland cement, silica and quartz, is applied and worked into the surface using a trowel.
FIRST DAY-STEP 7: Make the concrete surface smooth, using a trowel.
FIRST DAY-STEP 8: Dust the surface using Style Beton Release Powder, which adds two-tone color on the concrete and prevents the stamps to stick to the surface.
3 / 3
FIRST DAY-STEP 9: Use proper tamp tools into the stamp surface to achieve the required texture, with uniformity of pattern and depth of stamping.
AFTER THREE DAYS-STEP 10: After the concrete cures, it is rinsed with clean water to remove loose Release Powder.
THE SAME DAY-STEP 11: When the floor is dry, seal, using Style Beton Sealer, a UV resistant sealer that prevents color changes or fading caused by the sun. It is pure acrylic-based resin in virgin solvents for improved clarity and anti-yellowing characteristics.
Visit our website: www.stylebeton.com for more information and videos for all our products.
1 / 2
NANO-TOP APPLICATION
FAST AND EASY SELF LEVELING FLOOR
STEP 1:
We spread the surface, where Nano-Top will be applied, with
Acrylic Primer.
We continue spreading the surface, where Nano-Top will be
applied, with Acrylic Primer.
STEP 2:
We mix very well one bag Nano-Top (25kg) with 6 lt fresh and
clean water using low speed mixing.
We mix very well one bag Nano-Top (25kg) with 6 lt fresh
and clean water using low speed mixing.
2 / 2
STEP 3:
We apply Nano-Top, self leveling flooring.
We apply Nano-Top, self leveling flooring.
STEP 4:
We help a little bit in spreading Nano-Top with a trowel or
roller.
We help a little bit in spreading Nano-Top with a trowel or
roller.
Nano Top is ready.
You can find it in several colors, which can also be combined to
each other and create a “unique game of colors” or after the
floor is completely dry, it can be applied Acid Stain (see Acid
Stain Application).
Visit our website: www.stylebeton.com for more information and videos
about all our products.
1 / 2
DECO PEBBLE APPLICATION
FAST AND EASY
FIRST DAY-STEP 1: We mix every sack of Decopebble (25kg) with 5kg cement, gray or white.
FIRST DAY-STEP 2: We apply on concrete sub-base the mix of Decopebble. a) We apply minimum 2 cm (31,5kg/m²)Decopebble (wet-on-wet) on fresh concrete surface, which we have left to absorb the water. b) We apply minimum 4 cm (63kg/m²) Decopebble on old concrete surface, on which we have applied earlier a coat of Polystyle.
FIRST DAY-STEP 3: We apply the mix.
FIRST DAY-STEP 4: We make the surface smooth and leave the mix to absorb the surface water.
2 / 2
FIRST DAY-STEP 5: We spread the surface with Style Lack and cover the surface with nylon.
SECOND DAY-STEP 6: We rinse the surface, using water pump and fresh water.
SECOND DAY-STEP 7: Decopebble Floor is ready and we can apply Style Sealer, when the surface is dry.
Visit our website: www.stylebeton.com for more information and videos about all our products.
1 / 4
DECO CREATE APPLICATION
NEW IMPROVED FORMULATION
TWO DAYS PROCEDURE – LESS TIME, LESS COST
10 EASY STEPS
STEP 1:
Spread the surface, where you will apply Deco Create, with Style
Contact.
STEP 2:
Mix the ready to made plaster Deco Create with 5 lt (±0,500 Kg)
fresh and clean water .
Deco Create should be as thick as shown in the picture.
STEP 3:
Apply the first coat Deco Create (1-2mm) and right after that
continue with STEP 5. First and second coat should be applied wet to
wet.
2 / 4
STEP 4:
Apply the second coat Deco Create (1-5 cm), depending on the
pattern of the stamp you have choose.
STEP 5:
Make the surface smooth.
STEP 6:
Check the difference in thickness between first and second coat.
STEP 7:
Apply Style Liquid Release on the stamp, using a brush.
STEP 8:
Start stamping the plaster.
Continue stamping, covering all the surface.
3 / 4
Continue stamping, covering all the surface
STEP 9:
The same day, 3-4hours after stamping, Deco Create is still soft and
you can correct some details using Deco Create Tools.
STEP 10:
The second day you can start coloring using Decochrom, which is in
8 basic colors that you can mix. Try to begin with light colors and
small quantities.
You can use sponges to spread the colors on the surface.
It can be used a brush to painted joints, if it is not applicated from
the beginning colored plaster Deco Create.
A clean sponge can be used to remove the paint that has come off
plaster’s joints.
4 / 4
This is the final result of stamped wall Deco Create. You can change
the color if after some years you don’t like it.
1 / 3
BRICK-CREATE APPLICATION
LESS TIME – LESS COST THAN BRICK
STEP 1:
Apply the first coat Deco Create® (1-2mm).
STEP 2:
Apply the second coat Deco Create® (1.5cm) wet on
wet.
STEP 3:
Make the surface smooth.
2 / 3
Make the surface smooth.
STEP 4:
Apply the third coat Deco Create® (2 mm) wet on wet,
choosing the desirable color.
STEP 5:
Make the surface smooth.
Make the surface smooth.
3 / 3
STEP 6:
The next day use special tools Deco Create® to create
joints horizontally. During the summer you can do it the
same day, after some hours.
Also, use special tools Deco Create® to create joints
vertically.
Continue and create the look of brick, covering all the
surface.
LESS TIME-LESS COST THAN BRICK
1 / 5
ROCK-CREATE APPLICATION
STEP 1:
We cut the blocks of polystyrene and model them in
order to achieve shapes, very similar to natural rocks.
The same.
Final shape like a natural stone. We can assemble the
blocks using polyurethane foam.
2 / 5
STEP 2:
We spread the surface, where we will apply Rock
Create, with Style Contact.
STEP 3:
We install fiber glass mesh as a reinforcement of the
plaster.
STEP 6:
We apply primer Rock Create.
The same.
3 / 5
The result after the primer Rock Create.
STEP 4:
We apply Rock Create using a plaster sprayer.
We continue.
STEP 5:
We start texturing the surface using Style Beton®
stamps and Style Liquid Release.
4 / 5
The same.
The result after the texturing.
STEP 6:
We start coloring the surface using Rock Staining with
a brush, a sponge or a sprayer.
We continue.
5 / 5
We continue.
We color the surface using Rock Staining with a brush,
a sponge or a sprayer, until the wanted result.
Top Related