2 Channel Systems Manual
R
INC1185 Stanford Court, Anaheim, CA. 92805Tel:(714) 978-1895 Fax:(714) 978-1540
WWW.Airtronics.net
TRANSMITTER BATTERY INSTALLATION
RECEIVER AND SERVO CONNECTIONS
WARNINGSDO NOT OPERATE YOUR SYSTEM IF SOMEONEELSE IS ON YOUR FREQUENCY AT THE SAMTIME.YOUR MODEL CAN CAUSE SERIOUSDAMAGE OR INJURY SO PLEASE USE CAUTIONAND COURTESY AT ALL TIMES.
DO NOT EXPOSE THE RADIO SYSTEM TO WATER OREXCESSIVE MOISTURE.
PLEASE WATER PROOF THE RECEIVER AND SERVOSBY PLACING THEM IN PLASTIC BAGS OR A WATERTIGHT RADIO BOX WHEN OPERATING R/C BOAT MODELS.
IF YOU HAVE LITTLE OR NO EXPERIENCE OPERATINGR/C MODELS< WE STRONGLY RECOMMEND YOU SEEKTHE ASSISTANCE OF EXPERIENCED MODELERS ORYOUR LOCAL HOBBY SHOP FOR GUIDANCE.
Troubleshooting GuideIf your radio system does not operate properly, pleasecheck the following items:
1. Make sure the batteries are properly installed and check the polarity (+ and -) again.2. Check that both the transmitter and receiver power switches are in the ON position.3. Check the LED Power Indicators and make certain that all three are on. If not, replace the batteries.4. Make sure all the receiver and servo connections are tight.5. Make sure that the proper frequency crystals are installed in the transmitter and receiver.
1. Press down on the battery cover and slide in the direction of the arrow to remove.2. Install 8 pieces “AA” size alkaline batteries as indicated on the battery tray. Make sure to match the polarity (+ and -) as shown in the battery compartment or the transmitter will not function.3. Install the battery cover in place and slide to close.
WARNING: Improper installation of transmitter batteriescan cause serious damage to your system.
Your Blazer or Blazer Sport R/C system is equippedwith a BEC receiver to eliminate the need for aseparate battery receiver pack, but you can use aseparate power supply if desired for your particularmodel. The following diagram shows a typicalconnection for the servos and receiver.Note that the receiver antenna should be located atleast 2” (50 mm) away from any servo leads andswitches. In electric cars, we recommend that it beat least 4” (100mm) from the electric motor.
Extend the receiver antenna to the full length. Failureto do so will cause loss of control. Do not cut or bend thereceiver antenna.Be careful to avoid any metal parts coming in contactwith the servo connectors as this will affect theperformance. Insulate the connectors with tape or use tiewraps to avoid contact with metal car chassis.Please follow the model manufactures recommendationsfor the correct installation of your radio system in yourcar or boat.
R
To Open slide cover Install Batteries To Close slide cover
A B
NP-ADJ
STN
OR
REV
NO
RR
EV
TH
Steering Reverse Switch
Throttle Reverse Switch
Throttle Trigger AdjustmentTrigger Set Screw must beloosened before adjusting
Throttle Trigger Adjustment50/50 or 70/30(Forward and Reverse)
Trigger setScrew
OPE
N
OPE
N
OFF
ON
92621AIRTRONICS
92621AIRTRONICS
Steering Servo
ContenderSpeed Controller
Steering Servo
Throttle Servo
AA Dry Cell Battery Holder
Switch
To Battery
To Motor
Switch
B
#1
#2Speed Controller
To Battery
To Motor
#2
#1
BLAZERSport
THE CHOICE OF CHAMPIONS
ST-TRIM
TM-TRIM
LOW FULL
ADVANCED TECHNOLOGY FOR NEW GENERATION
ERGONOMIC CONCEPTION
AIRTRONICS
Sport
SYSTEM FEATURES
SYSTEM SPECIFICATIONS
(A) Transmitter
Model: Blazer SportOutput power: 500 MWModulation: AM/PPMPower supply: 8 AA alkaline dry cells DC 12VWeight: 14.46 ouncesFrequencies: 27 Mhz- 6 frequencies 75 MHz-30 frequencies
(B) Receiver (Mini BEC type)
Model: 92721Z (27 Mhz) or 92723Z (75 MHz)Modulation: AM/PPMIntermediate frequency: 455 KHzPower supply: DC 6.0-8.4 VWeight: 1.13 ouncesDimensions: 1.9”(L) x 1.3”(W) x .75”(H)
(C) Servo
Model: 94102Z Heavy duty standard servo
Weight: 1.59 ouncesSpeed: 0.18 sec. at 6.0V for 60 deg rotationTorque: 50 oz./inches:Operating Voltage 4.8~6.0
Power supply: 6.0 V throught BEC receiverDimensions: 1.54”(L) x .79”(W) x 1.42”(H)
(D) Accessories97004 BEC switch harnessFrequency flagReceiver dry battery holderInstruction Manual
(E) Options96315 Contender speed controller with reverse96720 Grip Pad99104 Deluxe wrist strap96305Z BL-Racer Speed Controller with reverse96316Z F-2000 Speed Controller with reverse96301Z ES-01 Micro Speed Controller with reverse
Unique and functional pistol grip-transmitter designWell balanced for precise controlWell placed trim and rate functionsHigh power outputColor LED power indicators for easy referenceof battery conditionRetractable transmitter antenna
Servo reversing for easy installation(70/30) Throttle triggerQuick access transmitter crystal.Lightweight, high performance mini receiverReceiver includes BEC (Battery Eliminator Circuit)which allows the use of a common power supply forthe model and receiverHigh torque and high speed 94102Z servoReceiver dry battery holderNiCd Charger Jack in transmitter
We appreciate your purchase of this newAIRTRONICS Blazer Sport Radio ControlSystem. These instructions are intendedto familiarize you with the many uniquefeatures of this modern, state of the artequipment.Please read them carefully so you mayobtain maximum success and enjoymentfrom its operation.
Please note that the Blazer Sport is designedfor comfort and precise control of all types ofmodel cars and boats. We wish you the bestof success with your radio system.Enjoy! LED Power Indicators
These color indicators will give you a visual reference forthe condition of the transmitter batteries.
All three indicators (2 green and 1 red) willbe lit when the power is on and thebatteries are in their best condition.
Two indicators (1 green and 1 red) will belit when the power is on and the batteriesare losing capacity. Use caution whenoperating you model, and replace thebatteries as soon as possible.
One indicator (red) will be lit when the poweris on and the batteries are dead or to weak topower the transmitter. DO NOT attempt tooperate your model, and replace the batteriesimmediately. If the batteries are improperlyinstalled, the LED indicators will not be lit.Check your battery installation and/orindividual batteries. DO NOT mix old and newbatteries
Full
Mid
Low
GreenGreenRed
RedGreen
Red
TRANSMITTER FUNCTIONS AND OPERATIONS
AntennaPull antenna up until it is fully extended before operating the system.Failure to do so can cause loss of control
The power switch slides up to turn onthe transmitter.When operating your model alwaysturn on the transmitter before thereceiver. This will prevent the modelfrom accidentally running away.
Power swicth
Attachment point for the optional 99104Deluxe Wrist Strap.
Wrist Band Hook
The transmitter crystal can beremoved to change frequencies.Use only genuineAIRTRONICS crystals to insureproper operation.
Transmitter crystal
Pull back for forward throttle.Push forward for reversethrottle/brake.
Throttle Trigger
Slide battery cover open as indicated onbattery cover. Install batteries as indicatedon battery tray.
Battery Cover
Only to be used when NiCd batteriesare installed.
NiCd Charger Jack
Steering dual rate is used to changesteering Sensitivity
Steering Dual Rate
Is used to adjust the neutral point forsteering operation.
Steering Trim
Is used to adjust the neutral point forthrottle / brake operation.
Throttle TrimTurn clockwise to make the modelturn right. Turn counter clockwise tomake the model turn left.
Steering Wheel
When the direction of the steering orthrottle movement is opposite fromthe direction of steering wheel ortrigger movement, move the switchto the rev or reverse position. Thiswill reverse the direction of the servomovement and allow you to operatethe model in the normal fashion.
In most models, you can leavethese switches in the nor or normalposition.
Reverse Switches
THE CHOICE OF CHAMPIONS
ST-TRIM
TM-TRIM
LOW FULL
ADVANCED TECHNOLOGY FOR NEW GENERATION
ERGONOMIC CONCEPTION
TM-TRIMTM-TRIM
Forward Reverse
AIRTRONICS
(Note) Dual Rate option noton some models
Sport
Top Related