8/14/2019 Tools for Sale
1/18
Tools For SaleAll Tools New & Used only for display or demo purposes only.
Contact 1st year Student @ Seneca - Jane Campus John Traicheff
Send email with any questions or interest to:
[email protected] [email protected]
mailto:[email protected]:[email protected]:[email protected]:[email protected]8/14/2019 Tools for Sale
2/18
No. 120 Series Series Dial Calipers
120Z-9 9
The Only American Made Dial Caliper This is one of the handiest measuring tools available, used bymechanics and toolmakers everywhere. It is direct reading, reliable and accurate.Comes with Finished Wooden Case.
Readability Features Sharp, clear dial graduations of .001 .100 in one revolution
Sharp, black graduations on the satin finished bar, every .100White inch dials
Ease-of-Handling Features Knife-edge contacts for both inside and outside measurements One hand use with the thumb-operated, fine adjustment roll Lock screw for dial bezel Lock screw for holding the sliding jaw in position 9 model have a covered rack depth rod Parallel lines can be scribed on workpiece by setting caliper jaw to the required dimensions, locking themovable jaw with the lock screw and then using the front edge of the fixed jaw as the scribing surface
Accuracy and Long-Life Features Hardened stainless steel bar, measuring surfaces, rack, gears and depth rod Positive, split-gear anti-backlash control Rack teeth point down to make it easy to shed foreign matter and thereby keep the area clean
QTY AVAILABLE ( 1 PR. ) LIST PRICE $325.00 SELLING FOR $180.00
8/14/2019 Tools for Sale
3/18
Precision Bench Level with Double Plumb 6
No. 132 Series 6" / 150mm
Moderately priced levels for all-around use; machinists, maintenance and set-up mechanics.
The base of the levels has an involute groove running the full length, which provides a reliable seat for
round work
All sizes have a main vial and double plumb vials. Each vial has two graduated lines
The main vials have approximately 19-minute sensitivity, meaning if the bubble moves 1/8" off the
graduated lines, the out-of-level is approximately .080" per foot. If the bubble is off 2mm, then the out-of-
level is approximately 4.4mm per meter
QTY AVAILABLE ( 1 ) LIST PRICE $145.00 SELLING FOR $60.00
Magnetic Base Universal Indicator Holder with Triple-Jointed Arm
No. 660
Small but powerful magnetic base, with 70 lbs. (320 N) holding force Positive On/Off switch Base Dimensions: 1" x1" x1" (9.5mm) stem or standard dovetail mount Articulating arm, powerful central locking knob, full 360 horizontal positioning, 180 vertical positioning Maximum Horizontal Reach: 4.750" (120mm) - - Maximum Vertical Reach: 7.500" (190mm) Very sensitive fine-adjustment thumb screw
QTY AVAILABLE ( 2 ) LIST PRICE $ 120.00 SELLING FOR $65.00
8/14/2019 Tools for Sale
4/18
No. 752A-18 18 Electronic Digital Height Gages (with output)
These Electronic height Gages provide a versatile and economic solution for most height measurementapplications. All measuring information from these tools can be entered directly into Starrett Data CollectionSystems for analysis, data collection, and hard copy documentation.
Specifications:LCD Readout Resolution 0.0005" (.005mm), Bar Graduations 0.100" and 5mm increments.Instant inch-millimetre conversion.Carrier and scriber designed to read from zero.Hold control feature retains a reading at any position.Plus or minus direction selector for reading correct measurements.Hardened and ground scriber.Fine adjustment for precise positioning accuracy. Lock screw.Powered by two 3V lithium coin-cell batteries with a life of over 1 year.Automatic shut-off to conserve battery life after 30 minutes of non-use.
QTY AVAILABLE ( 1 - 18 )
LIST PRICE $1670.00
SELLING FOR $750.00
Large, easy to read LCD display
Convenient battery operation with Automatic shut-off
Hardened and ground auxiliary scriber
Rugged stainless steel vertical bar
Knurled thumb screw locks scriber at any position
Two readout modes; large digital readout display andgraduated scale on column
Fine adjustment mechanism
8/14/2019 Tools for Sale
5/18
No. 20-3 Hardened Steel Square 3
Hardened Steel Squares
Hardened, ground and lapped to insure parallelism and straightness
Beam is grooved at inside corner for clearance
QTY AVAILABLE ( 1 ) LIST PRICE $156.00 SELLING FOR $45.00
No. 384A Series, Steel Parallels, 6" (150mm) Length, Pair: 1/8" (3mm) Thick, 1" (25mm)Width
QTY AVAILABLE ( 1 PR. ) LIST PRICE $83.00/pr. SELLING FOR $25.00/pr.
Starrett No. 384 Steel Parallels are hardened andground to close limits. They are indispensablefor inspection and layout work or for varioussetups on drill presses, milling and grindingmachines, shapers, etc. Furnished in pairs, 6length, they are made from a special grade oftool steel, hardened and accurately ground on
the four sides. In tools rooms or machine shops,several pairs of these parallels will be of greatvalue.
8/14/2019 Tools for Sale
6/18
8/14/2019 Tools for Sale
7/18
No. 123 Master Vernier Calipers 6 / 150mm (Metric & Inch. Versions available)
This vernier caliper is the ultimate example of slide caliper design. It is more accurate, has the easiest readingvernier style, is stronger and is offered in much longer lengths than other slide calipers.
Readability Features Long 50-division vernier scales, made popular by Starrett. This feature permits just half as many bargraduations as conventional single-vernier tools. These widely-spaced graduations make possible easy readingto .001 or 0.02mm without requiring a magnifying glass Flush fitting of the vernier scales to the main scale means that these are in the same plane, which eliminatesparallax. Vernier scales are adjustable The open-face design of the slide allows both the inside and outside vernier scale on the same side, thusallowing both verniers to be read without turning the tool over Black lines and figures against the Starrett satin chrome finish make reading a pleasure, not an effort
Screw-type adjusting nut allows for fine measuring adjustments Lock nut to hold measurements
Long-Life and Accuracy Features These tools are made of the finest tool steel. This makes the jaws harder and longer-wearing than stainlesstools. All tools through 24 (600mm) also have hardened and stabilized bars Measuring surfaces are hardened, ground and lapped to close limits All graduations are machine divided for accuracy, not photo-engraved. They are also deeper and sharper The combination straight and angular ways on the master bar allow for positive alignment of graduations andeasy adjustment of the flush-fitting verniers Divider points on the back side to accurately set dividers and trammels as needed Tools with inch and millimeter graduations on the same bar have outside readings only. (Inside readings mustbe compensated for by adding the nib width to the indicated reading.) The longer length of the adjusting jaw slide provides a longer bearing surface on the master bar, ensuringsquareness with the solid jaw and extra resistance to springing Tight, smoothly fitted slides for maximum accuracy and easy adjustment Made to rigid Starrett standards
QTY AVAILABLE ( 2 - 6 ) LIST PRICE $600.00 SELLING FOR $225.00
QTY AVAILABLE ( 1 - 150mm ) LIST PRICE $600.00 SELLING FOR $225.00
8/14/2019 Tools for Sale
8/18
Electronic Calipers No. 799 Series 6 799-6
Starretts 799 Series Electronic Calipers are light,comfortable, easy-to-use, and constructed withfeatures that have made Starrett slide calipers themachinists first choice for many years.
The 799 offers a slim, streamlined profile, a large,clear, easy-to-read LCD display, long battery life,and function buttons for zero and inch/mm.
799 calipers are available in 0-6", 0-8", and 0-12"sizes and the newly available Extended Range 24"and 40". All sizes furnished in a fitted, protectivecase.
Features (all sizes) Lightweight, ergonomic design Inch/millimeter conversion reads .0005" or0.01mm Easy access to the single, long-life battery Last measuring position retained when shut off Hardened stainless steel body for long life
Fine adjustment thumb wheel Lock screw to hold the slide in position Resolution is .0005" (0.01mm) Zero at any position
6", 8" & 12" Calipers Only Large easy-to-read LCD, .32" high characters Automatic shut-off after 5 minutes of nonuse Linear accuracy meets DIN862 Integrated depth rod
QTY AVAILABLE ( 4 ) LIST PRICE $155.00 SELL FOR $60.00
8/14/2019 Tools for Sale
9/18
Universal Precision Gage - No. 995A
This versatile gage was specifically designed for gage makers, inspectors, tool and die makers andmachinists. There is no other similar gage available that combines the design, accuracy andusefulness of this tool for fine height setting and transfer within its range.
Features and attachments that make this a truly universal gage are Scriber Attachment thatcan be used as a height gage for comparison measuring with test indicators, or as a surfacegage for scribing an offset attachment or "foot" that permits setting in narrow areas orworking 1/8" (3.2 mm) below the base line and 1" (25.4 mm) and 3" (76.2 mm) extensions toincrease the measuring range
Gage has a stable width-to-length ratio of 3/4" (19 mm) wide and 5 1/4" (130 mm) length
Base and slide forgings are hardened and all working surfaces are accurately ground
The exclusive combination flat and "V" ways on the slide and base provides extreme
accuracy, and the three-point contact provides longitudinal movement without side play A fine adjustment for closer accuracy and faster settings eliminates slow, tedious
tapping to set the gage. There is no other similar gage with this important feature Applications Can be used as a height gage, scriber, planer and shaper gage, for gap
measurement, as an adjustable parallel, for transferring settings with indicators, for checkingand layout work on surface plates, and with gage blocks or sine bars
Works as a precision level for use in machine set ups and gage work
In all these applications flush surfaces permit use on the base, the end, the top of the slide and
either side
QTY AVAILABLE ( 1 ) LIST PRICE $305.00 SELLING FOR $180.00
8/14/2019 Tools for Sale
10/18
Dial Indicator No. 25 Series AGD Group 2; 0 - 1.000 In.
QTY AVAILABLE ( 2 ) LIST PRICE $155.00 SELLING FOR $85.00
Dial Indicator No. 25 Series AGD Group 2; 0 - .5mm
QTY AVAILABLE ( 1 ) LIST PRICE $235.00 SELLING FOR $120.00
Starrett No. 25-441J Dial Indicator
- Graduations 0.001 In.- Range per Revolution 0.100 In.- Dial Reading 0 100- Contact Points 0.250 In.- Continuous Reading Dial Size 2.25 In.
- Hardened Steel Gear Train and Jeweled Bearings- Bezel Adjustable- Dial White Finish, Satin Chrome Body- Features Continuous Dial up to 1.000 In.- Furnished with Lug-on-Centre Back- Interchangeable Contact Points
Starrett No. 81 -261J METRIC Dial Indicator
- Metric Graduations 0.002mm- One Revolution 0 .2mm- Total Travel 0 .5mm- Dial Reading 0 1 0 0 mm- Stem Dial 8mm (.375)- 1 1 1 /1 6 Dial size- Hardened Steel Gear Train and Jeweled Bearings- Bezel Adjustable
- Dial Yellow Finish (Metric), Satin Chrome Body- Furnished with Lug-on-Centre Back- Interchangeable Contact Points
8/14/2019 Tools for Sale
11/18
No. 2800-5 Digital Dial Gauge
Starrett Electronic Indicators have simple, powerful, easy-to-use function. Versions are available for
inch/metric and metric only.
Features Large, easy-to-read LCD AGD group 2 size Range: .500" or 12.7mm Resolution: .0005" or .01mm Power On / Off button Reverse travel ( control indicates direction) Zero setting at any position Long battery life 3/8" diameter stem for inch/mm model (8mm on metric-only model) 4-48 spindle thread on inch/mm model (M2.5 X .45 thread on metric-only model)
Lug-on-center back + additional flat back Dust cap Plastic storage case with clear cover
Simply move the spindle and the indicator turns ON, keeping true spindle position. Instant inch/millimetreconversion. Automatic OFF after 5 minutes of non use. 3/8 diameter stem. Zero at any position. Large,easy to read LCD display.
QTY AVAILABLE ( 1 ) LIST PRICE $176.00 SELLING PRICE $90.00
8/14/2019 Tools for Sale
12/18
No. 256M Series (50-75mm) Disc-Type Micrometers
These tools are used to measure the thickness of work sections such as ribs, lands, fins, cutting edges onform tools, and chordal thickness of gear teeth. Because of their large anvil and spindle faces.
Readability Features Starrett satin chrome finish no glare resists rust
Advanced sleeve design with staggered lines and distinct figures for precise and easy readability
Ease-of-Handling Features Balanced frame and thimble design insure easy handling and better readability Ring-type knurled lock nut for quick and sure locking lock nut with Ratchet Stop The combination ratchet and speeder for uniform pressure and quicker adjustment on all sizes Anvil and spindle discs are 1/2 (12.7mm) diameter tapering to .015 (0.4mm) edge thickness making itpossible to enter narrow grooves and recesses
Accuracy and Long-Life Features Rigid one-piece frame of drop forged steel Extremely hard and stable one-piece spindle (the heart of our accuracy) Micro-lapped measuring faces Quick and easy adjustment Starrett workmanship This tool is accurate to .00015 or 0.003mm measuring over the whole surface and .0002 or0.004mmmeasuring on the edges
QTY AVAILABLE ( 1 ) LIST PRICE $289.00 SELLING FOR $125.00
8/14/2019 Tools for Sale
13/18
Lock-Joint Calipers with fine-adjustment
No. 38 Series (Outside) 6
These calipers feature a joint that can be quickly and firmly locked by a partial turn of the large knurleddisc. A spring washer under the disc maintains proper tension of the legs when the joint is unlocked.
These calipers are also provided with an adjusting screw to permit fine adjustments for closemeasurements. After the legs have been set to approximate size and the joint locked, the finaladjustment is made by a few turns of the knurled adjusting nut.
The legs are made of a high-grade steel and well shaped. They are ruggedly constructed and nicelyfinished.
The sizes listed are leg lengths. Their actual measuring capacity is about one-third greater than thegiven size of the legs.
QTY AVAILABLE ( 1 ) LIST PRICE $89.00 SELLING FOR $25.00
38-6
8/14/2019 Tools for Sale
14/18
Yankee Spring-Type Calipers and Dividers with flat legs and quick-spring
or solid nut
Nos. 73 Series 6 (150mm)
73B-6
Starrett Yankee Calipers and Dividers are made from a high-grade steel and well finished.The legs are made of flat stock and are very durable. The fulcrum stud is hardened and has a smoothbearing
surface. The bow spring, although flexible, is exceedingly strong to assure reliability.
All sizes are available with either spring nut or solid nut. The Starrett quick-adjusting automatic-closingspring nut is designed for making fast, positive adjustments. The threads of the nut firmly engage thescrew at the slightest pressure from the leg. When the pressure is withdrawn, the nut automaticallyreleases itself, sliding freely over the screw. This feature saves time in opening and closing.
QTY AVAILABLE ( 1 ) LIST PRICE $36.00 SELLING FOR $15.00
Quick-adjusting spring nutmakes fast, accurate settings.
8/14/2019 Tools for Sale
15/18
Yankee Spring-Type Dividers with flat legs and quick-spring or solid nut
Nos. 83 Series 12 (300mm)
SEE ABOVE FOR DETAILS
83B-1212
QTY AVAILABLE ( 1 ) LIST PRICE $68.00 SELLING FOR $25.00
8/14/2019 Tools for Sale
16/18
Lock-Joint Transfer Type Calipers with fine-adjustment
No. 36 Series (Outside) 6 (150mm)
One of the handiest and most versatilecalipers ever made Starrett Lock-JointTransfer Calipers have three key featuresa transfer arm, fine-adjustment screw, andlocking joint.
The transfer arm makes it possible totransfer measurements from the inside of
chambered cavities, over flanges and otherplaces where it is necessary to move thelegs after they have been set to size.Simply lock the joint, loosen the transferarm binding nut and swing the leg out orin to clear the obstruction. Then move itback against the transfer arm stop andthe exact size can then be transferred toa rule or gage.
The adjusting screw permits closeadjustments for fine measurements. After
the legs have been set to approximate sizeand the joint locked, the final adjustment ismade by a few turns of the knurledadjusting nut. The joint can be quickly andfirmly locked by a partial turn of the largeknurled disc. A spring washer under thedisc maintains proper tension of the legswhen the joint is loosened.
The legs are made from a high-grade steeland are well-shaped. They are ruggedlyconstructed and nicely finished. 36 - 6
The sizes listed are the length of the legs.Their actual measuring capacity is aboutone-third greater than the size of the legs.
QTY AVAILABLE ( 1 ) LIST PRICE $108.00 SELLING FOR $40.00
8/14/2019 Tools for Sale
17/18
Hermaphrodite Calipers
Lock-Joint with fine-adjustment
No. 42 Series 6 (150mm)
42-6
These calipers have an adjustable point, locking joint and fine-adjustment feature for closemeasurements. After the legs have been set to approximate size and the joint locked, the finaladjustment is made by a few turns of the knurled adjusting nut.
*NOTE: Actual capacity is one-third greater than the listed size.
QTY AVAILABLE ( 1 ) LIST PRICE $86.00 SELLING FOR $30.00
8/14/2019 Tools for Sale
18/18
MISC ODDS AND ENDS
Manufacturer Moore & Wright. A large headed nut screw assembly provides a firm and rigid frictionjoint, with no play. Upper Jaw & Lower Jaw Length 6.
QTY ( 1 ) SELLING FOR $5.00
QTY ( 1 ) SELLING FOR $5.00
GROZ 6 Hermaphrodite Caliper
The perfect tool when you need to scribe aline using the edge of the workpiece as areference plane.
Easy adjustment over entire range
Top Related