7/22/2019 Sigma Coating s
1/1103
7/22/2019 Sigma Coating s
2/1103
7/22/2019 Sigma Coating s
3/1103
7/22/2019 Sigma Coating s
4/1103
7/22/2019 Sigma Coating s
5/1103
7/22/2019 Sigma Coating s
6/1103
7/22/2019 Sigma Coating s
7/1103
7/22/2019 Sigma Coating s
8/1103
March 2013
page 1/3
3 pages
Revision of September 2004
FLUORGUARD 7000
two component, air drying, fluoropolymer based topcoat with excellent weather
resistance and color retention
excellent resistance to atmospheric exposure conditions very good colour and gloss retention
excellent resistance to chemical, acid, alkali can be applied by airless spray, roller and brush
colours available on request gloss
1.2 g/cm
approx. 36% by volumeRecommended dry film thickness 20 - 40 m
Theoretical spreading rate 18.0 m/l for 20 m9.0 m/l for 40 m
1 hours at 20 Cmin.5 hours at 20 C
max. unlimited12 months
previous coat; dry and free from any contamination
substrate temperature should be at least 3C above dew point maximum relative humidity during application and curing is 85%
mixing ratio by volume: base to hardener 7:1
mix thoroughly by a mechanical mixer before application Agitate continuously during application
none5 hours at 20 C
Recommended thinner Thinner 21-06Volume of thinner 5 - 10%
Nozzle orifice approx. 1.0 - 1.5 mm (= 0.039 - 0.059 in)
Nozzle pressure 30 - 40 MPa (= approx. 300 - 400 bar; 4351 - 5802 p.s.i.)
Recommended thinner Thinner 21-06
Volume of thinner 0 - 5%
Nozzle orifice approx. 0.33 - 0.48 mm (= 0.013 - 0.019 in)
Nozzle pressure 12 - 15 MPa (= approx. 120 - 150 bar; 1740 - 2176 p.s.i.)
Recommended thinner Thinner 21-06Volume of thinner 0 - 3%
Description
PRINCIPAL CHARACTERISTICS
COLOURS AND GLOSS
BASIC DATA
Mass densityVolume solids
Touch dry afterOvercoating interval
Shelf life (cool and dry place)
RECOMMENDED
SUBSTRATE CONDITIONSAND TEMPERATURES
INSTRUCTIONS FOR USE
Induction timePot life
AIR SPRAY
AIRLESS SPRAY
BRUSH/ROLLER
7/22/2019 Sigma Coating s
9/1103
March 2013
page 2/3
FLUORGUARD 7000
Thinner 21-06
It is always the aim of PPG Protective and Marine Coatings to supply the same
product on a worldwide basis. However, slight modification of the product issometimes necessary to comply with local or national rules/circumstances.
Under these circumstances an alternative product data sheet is used
Explanation to product data sheets see information sheet 1411Safety indications see information sheet 1430
Safety in confined spaces and health safetyExplosion hazard - toxic hazard see information sheet 1431
for paint and recommended thinners see safety sheets 1430, 1431 andrelevant material safety data sheets
CLEANING SOLVENT
Worldwide availability
REFERENCES
SAFETY PRECAUTIONS
7/22/2019 Sigma Coating s
10/1103
March 2013
page 3/3
FLUORGUARD 7000
WARRANTY
PPG warrants (i) its title to the product, (ii) that the quality of the product conforms to PPGs specifications for such product
in effect at the time of manufacture and (iii) that the product shall be delivered free of the rightful claim of any third person for
infringement of any U.S. patent covering the product. THESE ARE THE ONLY WARRANTIES THAT PPG MAKES AND ALL
OTHER EXPRESS OR IMPLIED WARRANTIES, UNDER STATUTE OR ARISING OTHERWISE IN LAW, FROM A COURSE
OF DEALING OR USAGE OF TRADE, INCLUDING WITHOUT LIMITATION, ANY OTHER WARRANTY OF FITNESS FOR A
PARTICULAR PURPOSE OR USE, ARE DISCLAIMED BY PPG. Any claim under this warranty must be made by Buyer to PPG
in writing within five (5) days of Buyers discovery of the claimed defect, but in no event later than the expiration of the applicable
shelf life of the product, or one year from the date of the delivery of the product to the Buyer, whichever is earlier. Buyers failure
to notify PPG of such non-conformance as required herein shall bar Buyer from recovery under this warranty.
LIMITATIONS OF LIABILITY
IN NO EVENT WILL PPG BE LIABLE UNDER ANY THEORY OF RECOVERY (WHETHER BASED ON NEGLIGENCE
OF ANY KIND, STRICT LIABILITY OR TORT) FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES IN ANY WAY RELATED TO, ARISING FROM, OR RESULTING FROM ANY USE MADE OF THE PRODUCT.
The information in t his sheet is i ntended for guidance only and i s based upon laboratory tests that PPG believes to
be reliable. PPG may modify the information contained herein at any time as a result of practical experience and
continuous product development. All recommendations or suggestions relating to t he use of the PPG product,
whether in technical documentation, or in response to a specific inqu iry, or otherwise, are based on data, which to the
best of PPGs knowledge, is reliable. The product and related information is designed for users having the requisi te
knowledge and industrial skills i n the industry and it is the end-users responsibility to determine the suitability of
the product for its own particular use and it shall be deemed that Buyer has done so, as its sole discretion and risk.
PPG has no control over either the quality or condition of the substrate, or the many factors affecting the use and
application of the product. Therefore, PPG does not accept any liability arising from any loss, injury or damage
resulting from such use or the contents of this inf ormation (unless there are written agreements stating otherwise).
Variations in the application environment, changes in procedures of use, or extrapolation of data may cause
unsatisfactory results. This sheet supersedes all previous versions and it i s the Buyers responsibili ty to ensure that
this i nformation is current prior t o using the product. Current sheets for all PPG Protective & Marine Coatings Products
are maintained at www.ppgpmc.com. The English text of this sheet shall prevail over any translation thereof.
PDS 8570
7/22/2019 Sigma Coating s
11/1103
7/22/2019 Sigma Coating s
12/1103
HI-TEMP COATINGS TECHNOLOGY P.O. Box 2347 Acton, MA 01720Tel: 978-635-1110 Fax: 978-635-1124 [email protected] www.hitempcoatings.com
Rev. 090412 Page 1 of 4
Hi-Temp 1027- CUI Prevents Corrosion Under Insulation- Stainless Steel Prevents Stress Corrosion Cracking- DTR Direct to Tight, Adherent Rust Application- Primer High Build, High Solids- Cryogenic Protects Cryogenic Equipment
PRODUCT DESCRIPTION:Service Temperature: minus 300F to 1200F [minus 185C to 650C]
Surface Application Temperatures: 50F to 600F [10C to 316C]*
Hi-Temp 1027 is a high-build, single component coating formulated to prevent corrosion under insulation ofcarbon and stainless steel.
Hi-Temp 1027 is formulated to help prevent chloride induced stress corrosion cracking of stainless steel andhas been tested by an independent laboratory for low leachable chlorides, sulfides and halides. It helps protectagainst chlorides: 1) from the atmosphere, 2) from by-products of process operations, and 3) which may beincorporated in the insulation, from coming in contact with stainless steel.
Hi-Temp 1027 is a low VOC, high build primer which air dries at ambient temperatures to a UV resistant andstable film, and provides excellent corrosion resistance at the full range of service temperatures.
Hi-Temp 1027 can be top coated with a full range of Hi-Temp color top coats.
Hi-Temp 1027 can be applied directly to hot substrates having a metal temperature up to 600F [316C]*,
eliminating the need for costly shutdown during maintenance. Hi-Temp 1027 does not require a heat cure to achieve superior corrosion resistance. Hi-Temp 1027 is resistant to thermal shock and thermal cycling in intermittent (wet, steam, dry) service. Hi-Temp 1027 can be applied to tightly adhering rust in maintenance and repair situations. Hi-Temp 1027 will protect cryogenic equipment in continuous or cyclic operation from minus 300F to 1000F
[minus 185C to 538C]. Hi-Temp 1027 provides a UV-resistant, chalking-free film with no maximum recoat interval, regardless of
operating temperature, as long as the surface to be recoated is clean and free of all contaminants.
TECHNICAL DATA:
Components: One
Type: Inert Multipolymeric Matrix
Dry Temperature Resistance: 1200
F [650
C] Continuous, 1400
F [760
C] PeakCryogenic Service: Minus 300F to 1000F [Minus 185C to 538C]
Adhesion ASTM 3359-09: 4A to 5A
Impact ASTM G-14 (direct): 30 lbs.
Colors Available: Black (Dark Gray), Gray, and Light Gray
Minor color change may occur in exposed service, but corrosion protection will not be compromised.
Finish: Flat
Dry Time @ 50% R.H., 70F [21C]:(Recoat and dry times are reduced whenapplied to hot substrates)
To touch 2 hoursTo ship 24 hoursTo topcoat 6 hours
Substrate Temperature During Application: 50F [10C] and rising to 600F [316C]*Thinner/Cleanup: See Mixing, Thinning, and Cleanup Table
Volume Solids: 65% 2% as applied
Coverage @ 1 mil DFT@ 25 microns DFT
1042 ft /gal[25.5 m
2/l]
VOC: 3.5 lbs/gal [420 g/l]
Weight: 16 lbs/gallon [1.92 kg/liter]
Packaging: 1 gallon cans; 50 gallon drums
Storage Temperatures: 40F to 120F [4C to 49C]
Shelf Life: Two years
*For direct application to hot substrates over 500F and up to 600F [260C to 316C]consult Hi-Temp Technical Service.
7/22/2019 Sigma Coating s
13/1103
Product: Hi-Temp 1027 Page 2 of 4Rev. 090412
SURFACE PREPARATION:
As wi th all coatings, the performance and service l ife of Hi -Temp 1027 are relative to the qual ity o f sur facepreparation accomplished.
CARBON STEEL All surfaces to be coated with Hi-Temp 1027 shall be free of all weld splatter, oil, dirt, grease,and all other contaminants, especially salts. Round off all rough welds and sharp edges.
In maintenance and repair situations, Hi-Temp 1027 can be applied over a surface in which tightly adhering rust isstill present;remove all rust scale and loosely adhering rust until glints of bright metal are visible. The remainingrust must be tightly adherent and not easily removed by lightly wiping with a cloth.
Hi-Temp 1027 should only be used to overcoat inorganic zinc or itself. When overcoating aged inorganic zinc,prepare a small test patch and check for adhesion. If previously applied coatings other than inorganic zinc or Hi-Temp 1027 are not fully removed by the method of surface preparation utilized, feather the edges of any remainingold coating, and use Hi-Temp 1027 to spot prime only the areas where the substrate is exposed.
Non-insulated surfaces:
Recommended: Dry abrasive blast clean to SSPC-SP 6, Commercial Blast [Sa 2] with a 1.0 to 2.0 mil [25to 50 micron] profile.
When abrasive blast cleaning is not an option, the following methods are acceptable:
SSPC-SP 15 Commercial Grade Power Tool Cleaning, with a minimum 1.0 mil [25 micron] profile.
SSPC-SP 12, Surface Preparation and Cleaning of Metals by Waterjetting Prior to Recoating to meet thevisual definition of WJ-3, Thorough Cleaning. Use potable water.
SSPC-SP 3, Power Tool Cleaning [St 3] or SSPC-SP 2, Hand Tool Cleaning [St 2].
Insulated surfaces:
Recommended: Dry abrasive blast clean to SSPC-SP 6, Commercial Blast [Sa 2] or better, with a 1.0 to2.0 mil [25 to 50 micron] profile.
When abrasive blasting is not an option, the following methods are acceptable:
SSPC-SP 15 Commercial Grade Power Tool Cleaning, with a minimum 1.0 mil [25 micron] profile.
SSPC-SP 12, Surface Preparation and Cleaning of Metals by Waterjetting Prior to Recoating to meet thevisual definition of WJ-2 Very thorough or Substantial Cleaning. Use potable water. All existing coatingmust be removed except for aged inorganic zinc or existing Hi-Temp 1027.
Power Tool Clean or Hand Tool Clean to remove all existing coating except for aged inorganic zinc orexisting Hi-Temp 1027.
STAINLESS STEEL All surfaces to be coated with Hi-Temp 1027 shall be free of all weld splatter, oil, dirt,grease, and all other contaminants, especially salts. Round off all rough welds and sharp edges.
IMPORTANT: DO NOT USE CHLORINATED SOLVENTS ON STAINLESS STEEL SURFACES.
Non-insulated and insulated sur faces:
Small surfaces may be cleaned with a chloride free solvent. Large surfaces may be cleaned utilizing ahigh or low pressure wash or steam cleaning with an alkaline detergent, followed by a freshwater rinse.Water used should be potable grade or better and should be checked to assure minimal salt content. Donot use any chemical additives in the rinse water.
An anchor profile is not mandatory for adhesion of Hi-Temp 1027 on stainless steel surfaces.o As an option, following cleaning, a light abrasive sweep blast using an appropriate chloride free
abrasive may be performed. After completion of this mechanical surface preparation, rinse the surfacewith potable grade water or better. Always allow rinsed surfaces to dry before coating.
7/22/2019 Sigma Coating s
14/1103
Product: Hi-Temp 1027 Page 3 of 4Rev. 090412
MIXING, THINNING, AND CLEANUP:
Hi-Temp 1027 is a heavy bodied material; use mechanical agitation for mixing immediately before application andas needed during application. Be sure any settled solids are incorporated during mixing. If thinning is needed, thinonly with Hi-Temp thinners and in accordance with applicable regulations. Agitate as needed during application.
Application to ambient substrateBelow 150F [66C]
Application to hot substrate 150F to 500F[66C to 260C]
Flush equipment and thin with Hi-Temp #10 or #11 Flush equipment and thin with Hi-Temp #5
Clean up with Thinners #5, #10, #11
For application to hot substrates over 150F and up to 500F [66C to 260C] thin (if needed) only with Hi-Temp thinner #5. For application to subst rates over 500F and up to 600F [260C to 316C] consultHi-Temp Technical Service.
APPLICATION:
For ambient application, surface temperature should be a minimum of 5F [3C] above the dew point. Do not applyto surfaces with surface temperature below 50F [10C]. Do not exceed recommended maximum dry filmthicknesses for the appropriate service type and temperatures.
APPLICATION TO HOT SURFACES:
IMPORTANT! It is essential to apply multiple thin passes of Hi-Temp 1027 during application to hot steel. Thisprocess, similar to mist coating, prevents blistering and also allows solvent to escape without leaving pinholes. Useof a solvent other than Hi-Temp #5 thinner could produce a fire hazard, and dry spray and poor filmcharacteristics may also result. If blisters are observed in Hi-Temp 1027 applied to hot surfaces, immediately brushout the blisters before they set, using a wood-handled china bristle brush. Note that the higher the substratetemperature, the shorter the recoat time.
For direct application to hot substrates over 500F and up to 600F [260C to 316C] consult Hi-Temp
Technical Service.
APPLICATION EQUIPMENT:
Spray application is recommended: Use conventional or airless spray and good painting practices. Typicalequipment is as follows:
Product Conventional Spray Airless Spray
AirPressure
FluidPressure
Fluid Tip Pressure Minimum FluidLine
Tip size
1027 60-80 psi
7/22/2019 Sigma Coating s
15/1103
Product: Hi-Temp 1027 Page 4 of 4Rev. 090412
II. PRIMER / TOPCOAT SYSTEM NON-INSULATED SERVICECarbon Steel / Stainless Steel Applied direct to hot or ambient steel
Primer Coat - Hi-Temp 1027 - 1 coat @ 5 to 6 mils DFT [125 to 150 microns]
Hi-Temp Color Topcoats (See appropriate topcoat PDS)a] Ambient apply: Hi-Temp 500VS or Hi-Temp 1000VS
b] Hot apply: Hi-Temp 500VHA or Hi-Temp 1000VHA
III. CRYOGENIC INSULATED AND NON-INSULATED SERVICEAmbientStainless Steel
Hi-Temp 1027[1.] For service temperature of minus 100 F to 400 F [minus 73C to 204C]
2 coats @ 5 to 6 mils [125 to 150 microns] DFT per coat; total of 10 to12 mils [250 to 300 microns]
[2.] For service temperature of minus 300 F to 1000 F [minus 185 C to 538C]1 coat @ 5 to 6 mils [125 to 150 microns] - DO NOT EXCEED 8 mils [200 microns] total DFT
RECOMMENDED APPLICATION PER COAT:
Minimum MaximumMils Microns Mils Microns
Dry Film Thickness 5 [125] 6 [150]
Wet Film Thickness 7.7 [192] 9.2 [230]
Coverage 208 ft2/gal [5.1 m
2/l] 174 ft
2/gal [4.3 m
2/l]
APPROXIMATE DRY SCHEDULE:
Substrate Temperature at50% RH 50F [10C] 70F [21C] 100F [38C] 302F [150C]
Dry to Recoat, Minimum 24 hours 6 hours 5 hours 1/4 hour
Dry to Recoat, Maximum No maximum as long as the surface is clean and free of contaminants
Dry to Ship 24 hours 24 hours 24 hours N/ACured N/A N/A N/A N/A
Dry times can vary based on environmental and substrate conditions.Do not exceed maximum dry film thickness recommendations as this can affect dry times.
PRECAUTIONS:
This product is for use only by professional applicators in accordance with information in this data sheet and theapplicable material safety data sheets (MSDS). Refer to the appropriate MSDS before using this material. All useand application of this product should be performed in compliance with all relative federal, state and local health,safety and environmental regulations or in compliance with all pertinent local, regional and national regulations aswell as good safety practices for painting, and in conformance with recommendations in SSPC-PA 1, Shop, Fieldand Maintenance Painting of Steel.
WARRANTY:
Hi-Temp Coatings Technology, Inc. (Hi-Temp) warrants that its products are free from defects in material andworkmanship. Hi-Temps sole obligation and buyers exclusive remedy shall be limited to replacement of productsnot conforming to this warranty. Any claim for replacement product must be made within one year from the deliverydate. Hi-Temp makes no other warranties, expressed or implied, such as warranties of merchantability or fitness fora particular purpose. Hi-Temp products are intended for buyers with the knowledge and skills to evaluate thesuitability of Hi-Temps products for buyers intended use. In no event shall Hi-Temp be liable for consequential orincidental damage.
7/22/2019 Sigma Coating s
16/1103
HI-TEMP COATINGS TECHNOLOGY P.O. Box 2347 Acton, MA 01720Tel: 978-635-1110 Fax: 978-635-1124 hitemp@hitempcoatings .com www.hitempcoatings.com
Rev. 082012 Page 1 of 3
HI-TEMP 1000VS Heat Resistant Standard and Custom Color Topcoats Superior Color Stability to 1000F [538C] Ambient Temperature Cure & VOC < 3.5 lb/gal
PRODUCT DESCRIPTION:For use as a topcoat fo r Hi-Temp 1027
Hi-Temp 1000VS is formulated with a highly engineered silicone resin, enabling it to withstand severethermal cycling to 1200F [649C]. This also allows Hi-Temp 1000VS to have superior color stability ascompared to most generic silicone topcoats, which tend to discolor at elevated temperatures.
Hi-Temp 1000VS is available in both standard and custom colors. Hi-Temp 1000VS air dries rapidly and does not require heat cure. Hi-Temp 1000VS has excellent spray application properties. Hi-Temp 1000VS is a user-friendly system that can be brushed and rolled. Hi-Temp 1000VS has excellent weathering and corrosion resistance when applied over properly primed
surfaces.
Hi-Temp 1000VS does not soften in thermal cyclic service. Color stability may be affected at the top end of the temperature range. Hi-Temp 1000VS is specifically formulated as an ambient, heat resistant topcoat for Hi-Temp 1027.TECHNICAL DATA:
Type: Silicone
Dry Temperature Resistance: To 1200F [650C]
Color Stability: Standard & Custom To 1000F [538C]
Black To 1200F [650C]
Colors: Standard & Custom
Finish: Flat
Components: One
Dry Time @ 50% R.H., 70F [21C]
- To touch Two Hours
- To ship 24 Hours
Cure: N/A
Metal Temperature During Application: 50F to 150F [10C to 66C]
Thinner: Hi-Temp #10 or #11
Volume Solids: 34%
Theoretical Coverage @1 mil DFT 545 ft2/gal
Theoretical Coverage @25 microns 13.4 m2/l
VOC Content: 3.5 lb/gal [420 g/l]
Weight per Gallon: 11.4 lb. [5.2 kg]
Storage Temperature: 40F to 120F [4C to 49C]
Shelf Life:
One year
SURFACE PREPARATION: Performance of the coating system is relative to the surface preparation accomplished.
Hi-Temp 1000VS is designed to be applied over Hi-Temp 1027 primer.
7/22/2019 Sigma Coating s
17/1103
Product: Hi-Temp 1000VS Page 2 of 3Rev. 082012
New or Corroded Surfaces:
For corrosion resistant service, use of an approved corrosion resistant primer is necessary. Surfacesto be coated must be primed in accordance with the Hi-Temp 1027 product data sheet. Consult Hi-Temp for alternate and approved primers. Allow appropriate dry time. Apply one coat of Hi-Temp1000VS at 2 to 2.5 mils [50 to 63 microns] DFT.
For cosmetic service only, use of an approved corrosion resistant primer is recommended but notnecessary. Abrasive blast clean to SSPC-SP 6 Commercial Blast [Sa 2] with profile of 1 to 1.5
mils [25 to 38 microns] or pressure wash to an equivalent of SSPC-SP 6 [Sa 2] condition.Surfaces to be coated must be dry and free of salts, weld splatter, oil, dirt, grease, and all othercontaminants. Round off all rough welds and sharp edges. Apply two coats of Hi-Temp 1000VS at 2to 2.5 mils [50 to 63 microns] DFT per coat for a total of 4 to 5 mils [100 to 125 microns] DFT.
Previously Painted Surfaces in Good Condition : If old coating is intact and there is no evidence of cracking, fracturing, and/or delamination, pressure
wash surface to remove all salts, oil, grease, and contaminants and apply one coat of Hi-Temp1000VS at 2 to 2.5 mils [50 to 63 microns] DFT.
Previously Painted Surfaces in Poor Condition or w ith some Localized Corrosion :If old coating shows evidence of cracking, fracturing, delamination, and/or corrosion, follow surfacepreparation guidelines for new steel. If there is no evidence of cracking, fracturing, or delamination, justsmall areas of corrosion (less than 10% of the area to be coated), power wash the entire structure,
removing all salts, oil, grease, and other contaminants. Once dry, perform surface preparation and applyHi-Temp 1027 in accordance with the data sheet on all areas where the existing paint has been removed.Once these areas are primed and dry, apply one coat of Hi-Temp 1000VS at 2 to 2.5 mils [50 to 63microns] DFT over the entire surface.
Prior to application of 1000VS over other coatings, prepare a small test patch area andtest for adhesion.
MIXING, THINNING, AND CLEANUP:
Use mechanical agitation for mixing. Mix materials until uniform in consistency. Thinning is not normallyneeded. If a condition warrants thinning, thin only with Hi-Temp Thinners #10 or #11. Thin only inaccordance with applicable regulations.
Appl ication to Ambient Substrate 50F [10C] to 150F [66C]
Flush, Thin, and Clean up with: Hi-Temp Thinner #10 or #11
APPLICATION:
Surface temperature must be a minimum of 5F [3C] above the dew point. Do not apply at substratetemperatures below 50F [10C] or above 150F [66C].
APPLICATION EQUIPMENT:
Spray: Standard conventional or airless spray is highly recommended. Use good painting practices.Typical equipment is as follows:
Product Conventional Spray Airless Spray
AirPressure
FluidPressure
Fluid Tip Pressure Minimum FluidLine
Tip size
1000VS 60-80 psi
7/22/2019 Sigma Coating s
18/1103
Product: Hi-Temp 1000VS Page 3 of 3Rev. 082012
APPLICATION SYSTEMS:
Un-insulated steel Do not exceed recommended dry film thickness
Primer Hi-Temp 1027 5.0 to 6.0 mils [125 to 150 microns] DFT
Topcoat Hi-Temp 1000VS 2.0 to 2.5 mils [50 to 63 microns] DFT
Total Dry Film Thickness 7.0 to 8.5 mils [175 to 213 microns] DFT
RECOMMENDED APPLICATION PER COAT:
Hi-Temp 1000VS
Minimum Maximum
Mils Microns Mils Microns
Dr Film 2 [50] 2.5 [63]
Wet Film 5.9 [148] 7.3 [183]
Theoretical Coverage 273 ft2/gal [6.7 m2/l ] 218 ft
2/gal. [5.4 m
2/l]
DRY SCHEDULE:
Substrate Temperatureat 50% RH
50F [10C] 70F [21C] 90F [32C] 150F [66C]
Dry to touch 4 hours 2 hours 2 hours hour
Dry to Ship 72 hours 24 hours 16 hours hour
Cure N/A
When shipping and handling equipment coated w ith Hi-Temp 1000VS follow procedures for thin film coatings.
Avo id mechan ical damage and abrasion .
PRECAUTIONS:
This product is for use only by professional applicators in accordance with information in this data sheetand the applicable material safety data sheets (MSDS). Refer to the appropriate MSDS before using thismaterial. All use and application of this product should be performed in compliance with all relative federal,state and local health, safety and environmental regulations or in compliance with all pertinentlocal, regional and national regulations as well as good safety practices for painting, and inconformance with recommendations in SSPC PA 1, Shop, Field and Maintenance Painting of Steel.
WARRANTY:
Hi-Temp Coatings Technology, Inc. (Hi-Temp) warrants that its products are free from defects in materialand workmanship. Hi-Temps sole obligation and buyers exclusive remedy shall be limited to replacementof products not conforming to this warranty. Any claim for replacement product must be made within
one year from the delivery date. Hi-Temp makes no other warranties, expressed or implied, such aswarranties of merchantability or fitness for a particular purpose. Hi-Temp products are intended forbuyers with the knowledge and skills to evaluate the suitability of Hi-Temps products for buyers intendeduse. In no event shall Hi-Temp be liable for consequential or incidental damage.
7/22/2019 Sigma Coating s
19/1103
7/22/2019 Sigma Coating s
20/1103
page 1/3
April 20093 pagesRevision of November 2005
two component solvent free amine cured phenolic epoxy compound
sprayable caulking to overlap the welding seamssuitable caulking compound for use under SigmaGuard CSF 650 and
Novaguard 840excellent chemical resistance against crude oil, unleaded gasolines and a
wide range of petrochemicals and solvents
can be applied by heavy duty single feed airless spray equipment (60:1)good visibility due to light colour
reduced explosion risk and fire hazard
cream - gloss
(1 g/cm = 8.25 lb/US gal; 1 m/l = 40.7 ft/US gal)(data for mixed product)
1.4 g/cm
100%max. 105 g/kg (Directive 1999/13/EC, SED)
max. 144 g/l (approx. 1.2 lb/gal)3500 - 5000 m depending on system
6 hoursmin. 16 hours *
max. 3 months *5 days *
(data for components)
at least 12 months
steel; blast cleaned to a minimum of ISO-Sa2, blasting profile 50 - 100 m
steel with suitable holding primer (SigmaGuard 260 or SigmaCover 280)which must be dry, clean and free from any contamination
mixing ratio by volume: base to hardener 75 : 25
when mixing the temperature of the base and hardener should be at least
20Cat lower temperature the viscosity will be too high for spray application
no thinner should be added
none
1 hour at 20C *
* see additional data
DESCRIPTION
PRINCIPAL CHARACTERISTICS
COLOURS AND GLOSS
BASIC DATA AT 20C
Mass density
Volume solidsVOC (supplied)
Recommended dry film thickness
Touch dry afterOvercoating interval
Full cure after
Shelf life (cool and dry place)
RECOMMENDED
SUBSTRATE CONDITIONSAND TEMPERATURES
INSTRUCTIONS FOR USE
Induction time
Pot life
NOVAGUARD 830
7/22/2019 Sigma Coating s
21/1103
page 2/3
April 2009
NOVAGUARD 830
heavy duty single feed airless spray equipment with a minimum of 60:1pump ratio and suitable high pressure hoses
in-line heating or insulated hoses may be necessary to avoid cooling downof paint in hoses at low air temperature
length of hoses should be as short as possibleno thinner should be added
approx. 0.67 mm (= 0.026 in) at an angle of 30 40
at 20C (paint temperature) min. 30 MPa (= approx. 350 bar; 5000 p.s.i.)at 30C (paint temperature) min. 25 MPa (= approx. 250 bar; 3500 p.s.i.)
Thinner 90-83
all application equipment must be cleaned immediately after usepaint inside the spraying equipment must be removed before the pot life time
has been expired
for paint and recommended thinners see safety sheets 1430, 1431 and relevantmaterial safety data sheets
Film thickness and spreading rate
theoretical spreading rate m/l 0.3
dft in m 3000
structure: in different layers wet in wet in order to reach the required filmthickness
Overcoating table with solvent free tanklinings
substrate temperature 10C 20C 30C
minimum interval 30 hours 16 hours 12 hours
maximum interval 3 months 2 months 1 month
surface should be dry and free from any contamination
Curing table
substrate temperature dry to handle full cure
10C 30 hours 7 days
20C 16 hours 5 days
30C 10 hours 3 days
although the paint is solvent free adequate ventilation must be maintainedduring application and curing (please refer to sheet 1433 and 1434)
AIRLESS SPRAY
Recommended thinner
Nozzle orifice
Nozzle pressure
CLEANING SOLVENT
SAFETY PRECAUTIONS
ADDITIONAL DATA
7/22/2019 Sigma Coating s
22/1103
page 3/3
April 2009
NOVAGUARD 830
Pot life
20C 60 min.
30C 45 min.
due to exothermic reaction, temperature during and after mixing may
increase
Whilst it is always the aim of PPG Protective & Marine Coatings to supplythe same product on a worldwide basis, slight modification of the product is
sometimes necessary to comply with local or national rules/circumstances.
Under these circumstances an alternative product data sheet is used.
Explanation to product data sheets see information sheet 1411Safety indications see information sheet 1430
Safety in confined spaces and health safetyExplosion hazard - toxic hazard see information sheet 1431
Safe working in confined spaces see information sheet 1433Directives for ventilation practice see information sheet 1434
Cleaning of steel and removal of rust see information sheet 1490
LIMITATION OF LIABILITY
The information in this data sheet is based upon laboratory tests we believe to be accurate and is intended for
guidance only. All recommendations or suggestions relating to t he use of the Sigma Coatings products made by PPG
Protective & Marine Coatings, whether in technical documentation, or in response to a specific enquiry, or otherwise,
are based on data which to the best of our knowledge are reliable. The products and information are designed for
users having the requisite knowledge and industrial skil ls and it is the end-user's responsibility to determine the
suitability of the product for its int ended use.
PPG Protective & Marine Coatings has no control over either the quality or condition of the substrate, or the many
factors affecting the use and application of the product. PPG Protective & Marine Coatings does therefore not accept
any liability arising from loss, injury or damage resulting from such use or the contents of thi s data sheet (unless there
are written agreements stating otherwise).
The data contained herein are liable to modification as a result of practical experience and continuous productdevelopment.
This data sheet replaces and annuls all previous issues and it is therefore the user's responsibility to ensure that this
sheet is current prior to using the product.
The English t ext of this document shall prevail over any translation thereof.
PDS 7945
Worldwide availability
REFERENCES
7/22/2019 Sigma Coating s
23/1103
7/22/2019 Sigma Coating s
24/1103
February 2013
page 1/5
5 pages
Revision of March 2011
NOVAGUARD 840
two component solvent free amine cured novolac phenolic epoxy coating
one coat tank coating system
clear version for glassmat reinforced solvent free tank bottom system (seesystem sheet 4145)
excellent resistance to crude oil up to 90C suitable for storage of unleaded gasolines
good chemical resistance against a wide range of chemicals and solvents good visibility due to light colour
glossy and smooth appearance easy to clean
can be applied by heavy duty single feed airless spray equipment (60:1)
reduced explosion risk and fire hazard approved to Air BP F2D2 section 2.1 for the storage of jet fuels
green, cream, clear gloss
(1 g/cm = 8.35 lb/US gal; 1 m/l = 40.7 ft/US gal)
(data for mixed product)
1.3 g/cm100%
max. 106 g/kgmax. 142 g/l (approx. 1.2 lb/gal)
73 g/ltr (0.6 lb/gal) (by EPA Method 24) see information sheet 1411Recommended dry film thickness 300 - 600 m depending on system
Theoretical spreading rate 3.3 m/l for 300 m *
6 hours at 20Cmin. 24 hours *
max. 2 months *5 days * at 20C
(data for components)
at least 12 months* see additional data
steel; blast cleaned to a minimum of ISO-Sa2, blasting profile 50 - 100 m substrate temperature must be above 5C and at least 3C above dew point
during application and curing steel with suitable primer (SigmaGuard 260) which must be dry, clean and
free from any contamination
Description
PRINCIPAL CHARACTERISTICS
COLOURS AND GLOSS
BASIC DATA AT 20C
Mass densityVolume solids
VOC (Supplied)
VOC (EPA Method 24)
Touch dry afterOvercoating interval
Full cure after
Shelf life (cool and dry place)
RECOMMENDEDSUBSTRATE CONDITIONS
AND TEMPERATURES
7/22/2019 Sigma Coating s
25/1103
February 2013
page 2/5
NOVAGUARD 840
mixing ratio by volume: base to hardener 80 : 20
the temperature of the mixed base and hardener should preferably be atleast 20C
at lower temperature the viscosity will be too high for spray application no thinner should be added
for recommended application instructions: see working procedurenone
1 hours at 20C **see additional data
use heavy duty single feed airless spray equipment preferably 60:1 pump ratioand suitable high pressure hoses/in -line heating or insulated hoses may be
necessary to avoid cooling down of paint in hoses at low air temperaturelength of hoses should be as short as possible
Recommended thinner no thinner should be added
Nozzle orifice approx. 0.53 mm (= 0.021 in)
Nozzle pressure at 20C (paint temperature) min. 28 MPa (= approx. 280 bar; 4061 p.s.i.)at 30C (paint temperature) min. 22Mpa (=approx. 220 bar: 3000 p.s.i.)
only for spot repair and stripe coating
Recommended thinner no thinner should be added
Thinner 90-83 (preferred) or Thinner 90-53
paint inside the spraying equipment must be removed before the pot life timehas been expired
all equipment used for application must be cleaned immediately after use
Film thickness and spreading rate
theoretical spreading rate m/l 3.3 1.7
dft in m 300 600
Maximum dft when brushing: 150 m
measuring wet film thickness a deviation is often obtained between the measured apparent wft and the
real applied wft this is due to the thixotropy and the surface tension of the paint which
retards the release of air trapped in the paint film for some time recommendation is to apply a wft which is equal to the specified dft
plus 60 m
INSTRUCTIONS FOR USE
Induction time
Pot life
AIRLESS SPRAY
BRUSH/ROLLER
CLEANING SOLVENT
7/22/2019 Sigma Coating s
26/1103
February 2013
page 3/5
NOVAGUARD 840
measuring d ry film thickness
because of low initial hardness the dft cannot be measured within somedays due to the penetration of the measuring device into the soft paint film
the dft should be measured using a calibration foil of known thickness placedin between the coating and the measuring device
Overcoating with Novaguard 840 (spot repair and stripe coating)
substrate temperature 5C 10C 20C 30C
minimum interval 80 hours 36 hours 24 hours 16 hours
maximum interval 3 months 3 months 2 months 1 month
surface should be dry and free from any contamination
Curing table
substrate temperature dry to handle full cure
5C 60 hours 15 days
10C 30 hours 7 days
20C 16 hours 5 days
30C 10 hours 3 days
adequate ventilation must be maintained during application and curing
(please refer to sheets 1433 and 1434)
for storage and transport of drinking water the recommended workingprocedure should be followed
WASHING PROCEDURE
all personnel should wear watertight suits, boots and gloves properlycleaned with a sodium hypochlorite solution (1% active chlorine per liter)
all tank sides, bottom and deckheads etc. should be brush cleaned or high-pressure spray cleaned with 1% active chlorine solution as above
note: this can also be done by butterworth washing all parts should be high pressure cleaned with tap water and tanks drained
concentrated active chlorine solution should be sprinkled on bottom;approx. 1 ltr/10 m
tanks should be filled with tap water to a depth of approx. 20 cm and thewater should remain in the tank for at least 2 hours (max. 24 hours)
tanks should be thoroughly flushed out with tap water
depending upon local regulations it may be necessary to take watersamples, after filling tank completely, to check on bacteria
after this procedure the tanks will be fit to carry drinking water
Curing
7/22/2019 Sigma Coating s
27/1103
February 2013
page 4/5
NOVAGUARD 840
Pot life (at application viscos ity)
20C 60 min.
30C 45 min.
due to exothermic reaction, temperature during and after mixing mayincrease
It is always the aim of PPG Protective and Marine Coatings to supply the same
product on a worldwide basis. However, slight modification of the product issometimes necessary to comply with local or national rules/circumstances.
Under these circumstances an alternative product data sheet is used
Safety indications see information sheet 1430Safe working in confined spaces see information sheet 1433
Cleaning of steel and removal of rust see information sheet 1490Explanation to product data sheets see information sheet 1411
Safety in confined spaces and health safetyExplosion hazard - toxic hazard see information sheet 1431
Directives for ventilation practice see information sheet 1434
Specification for mineral abrasives see information sheet 1491Safety in confined spaces and health safety
Explosion hazard - toxic hazard see information sheet 1431Relative humidity - substrate temperature -
air temperature see information sheet 1650Conversion tables see information sheet 1410
for paint and recommended thinners see safety sheets 1430, 1431 and
relevant material safety data sheets although this is a solvent free paint, care should be taken to avoid inhalation
of spray mist as well as contact between the wet paint and exposed skin oreyes
no solvent present; however, spray mist is not harmless, a fresh air mask
should be used during spraying
ventilation should be provided in confined spaces to maintain goodvisibility
Worldwide availability
REFERENCES
SAFETY PRECAUTIONS
7/22/2019 Sigma Coating s
28/1103
February 2013
page 5/5
NOVAGUARD 840
WARRANTY
PPG warrants (i) its title to the product, (ii) that the quality of the product conforms to PPGs specifications for such product
in effect at the time of manufacture and (iii) that the product shall be delivered free of the rightful claim of any third person for
infringement of any U.S. patent covering the product. THESE ARE THE ONLY WARRANTIES THAT PPG MAKES AND ALL
OTHER EXPRESS OR IMPLIED WARRANTIES, UNDER STATUTE OR ARISING OTHERWISE IN LAW, FROM A COURSE
OF DEALING OR USAGE OF TRADE, INCLUDING WITHOUT LIMITATION, ANY OTHER WARRANTY OF FITNESS FOR A
PARTICULAR PURPOSE OR USE, ARE DISCLAIMED BY PPG. Any claim under this warranty must be made by Buyer to PPG
in writing within five (5) days of Buyers discovery of the claimed defect, but in no event later than the expiration of the applicable
shelf life of the product, or one year from the date of the delivery of the product to the Buyer, whichever is earlier. Buyers failure
to notify PPG of such non-conformance as required herein shall bar Buyer from recovery under this warranty.
LIMITATIONS OF LIABILITY
IN NO EVENT WILL PPG BE LIABLE UNDER ANY THEORY OF RECOVERY (WHETHER BASED ON NEGLIGENCE
OF ANY KIND, STRICT LIABILITY OR TORT) FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES IN ANY WAY RELATED TO, ARISING FROM, OR RESULTING FROM ANY USE MADE OF THE PRODUCT.
The information in t his sheet is i ntended for guidance only and i s based upon laboratory tests that PPG believes to
be reliable. PPG may modify the information contained herein at any time as a result of practical experience and
continuous product development. All recommendations or suggestions relating to t he use of the PPG product,
whether in technical documentation, or in response to a specific inqu iry, or otherwise, are based on data, which to the
best of PPGs knowledge, is reliable. The product and related information is designed for users having the requisi te
knowledge and industrial skills i n the industry and it is the end-users responsibility to determine the suitability of
the product for its own particular use and it shall be deemed that Buyer has done so, as its sole discretion and risk.
PPG has no control over either the quality or condition of the substrate, or the many factors affecting the use and
application of the product. Therefore, PPG does not accept any liability arising from any loss, injury or damage
resulting from such use or the contents of this inf ormation (unless there are written agreements stating otherwise).
Variations in the application environment, changes in procedures of use, or extrapolation of data may cause
unsatisfactory results. This sheet supersedes all previous versions and it i s the Buyers responsibili ty to ensure that
this i nformation is current prior t o using the product. Current sheets for all PPG Protective & Marine Coatings Products
are maintained at www.ppgpmc.com. The English text of this sheet shall prevail over any translation thereof.
PDS 7468
237775 cream 3012002200
180207 green 4000001400
7/22/2019 Sigma Coating s
29/1103
7/22/2019 Sigma Coating s
30/1103
September 2013
page 1/5
5 pages
Revision of November 2012
NOVAGUARD 890
two component solvent free amine cured novolac phenolic epoxy coating
one coat tank coating system
excellent resistance to crude oil up to 90C suitable for storage of unleaded gasolines blended up to 100% ethanol
(E5 up to E100) suitable for storage of biodiesel (EN14214)
good chemical resistance against a wide range of chemicals and solvents good visibility due to light colour
semigloss and smooth appearance clear version for glassmat reinforced solvent free tank bottom system (see
system sheet 4155)
easy to clean can be applied by heavy duty single feed airless spray equipment (60:1)
reduced explosion risk and fire hazard
green, cream, clear semi-gloss
(1 g/cm = 8.35 lb/US gal; 1 m/l = 40.7 ft/US gal)
(data for mixed product)
1.4 g/cm
100%max. 94 g/kg (Directive 1999/13/EC, SED)
max. 131 g/l (approx. 1.1 lb/gal)see information sheet 1411
Recommended dry film thickness 300 - 600 m depending on system
Theoretical spreading rate 3.3 m/l for 300 m *8 hours at 20C
min. 24 hours *max. 2 months *6 days *
(data for components)
at least 12 months* see additional data
steel; blast cleaned to a minimum of ISO-Sa2, blasting profile 50 - 100 m substrate temperature should be above 5C and at least 3C above dew
point during application and curing steel with suitable primer (SigmaGuard 260) which must be dry, clean and
free from any contamination
Description
PRINCIPAL CHARACTERISTICS
COLOURS AND GLOSS
BASIC DATA AT 20C
Mass density
Volume solidsVOC (Supplied)
Touch dry after
Overcoating interval
Full cure after
Shelf life (cool and dry place)
RECOMMENDEDSUBSTRATE CONDITIONS
AND TEMPERATURES
7/22/2019 Sigma Coating s
31/1103
September 2013
page 2/5
NOVAGUARD 890
mixing ratio by volume: base to hardener 80 : 20
the temperature of the mixed base and hardener should preferably be at
least 20C no thinner should be added
for recommended application instructions: see working procedure at lower temperature the viscosity will be too high for spray application
none1 hour at 20C *
* see additional data
Recommended thinner no thinner should be added
Nozzle orifice approx. 0.53 mm (=0.021 in)
Nozzle pressure at 20C (paint temperature) min. 28 MPa (= approx. 280 bar; 4061 p.s.i.)at 30C (paint temperature) min. 22Mpa (=approx. 220 bar: 3000 p.s.i.)
use heavy duty single feed airless spray equipment preferably 60:1 pumpratio and suitable high pressure hoses
for stripe coating and spot repair onlyRecommended thinner no thinner should be added
Thinner 90-83 (preferred) or Thinner 90-53
all application equipment must be cleaned immediately after use paint inside the spraying equipment must be removed before the pot life time
has been expired
Film thickness and spreading rate
theoretical spreading rate m/l 3.3 1.7
dft in m 300 600
Maximum dft when brushing: 150 m
measuring wet film thickness a deviation is often obtained between the measured apparent wft and the
real applied wft
this is due to the thixotropy and the surface tension of the paint whichretards the release of air trapped in the paint film for some time
recommendation is to apply a wft which is equal to the specified dftplus 60 m
INSTRUCTIONS FOR USE
Induction timePot life
AIRLESS SPRAY
BRUSH/ROLLER
CLEANING SOLVENT
ADDITIONAL DATA
7/22/2019 Sigma Coating s
32/1103
September 2013
page 3/5
NOVAGUARD 890
measuring d ry film thickness
because of low initial hardness the dft cannot be measured within somedays due to the penetration of the measuring device into the soft paint film
the dft should be measured using a calibration foil of known thickness placedin between the coating and the measuring device
Overcoating table with itself (spot repair and s tripe coating)
substrate temperature 10C 20C 30C
minimum interval 36 hours 24 hours 16 hours
maximum interval 3 months 2 months 1 month
surface should be dry and free from any contamination
Curing table
substrate temperature dry to handle full cure
10C 40 hours 10 days
20C 18 hours 6 days
30C 12 hours 4 days
adequate ventilation must be maintained during application and curing(please refer to sheets 1433 and 1434)
for storage and transport of drinking water the recommended working
procedure should be followed
Pot life (at application viscos ity)
20C 60 min.
30C 45 min.
due to exothermic reaction, temperature during and after mixing may
increase
It is always the aim of PPG Protective and Marine Coatings to supply the sameproduct on a worldwide basis. However, slight modification of the product is
sometimes necessary to comply with local or national rules/circumstances.Under these circumstances an alternative product data sheet is used
Curing
Worldwide availability
7/22/2019 Sigma Coating s
33/1103
September 2013
page 4/5
NOVAGUARD 890
Conversion tables see information sheet 1410
Explanation to product data sheets see information sheet 1411Safety indications see information sheet 1430
Safety in confined spaces and health safetyExplosion hazard - toxic hazard see information sheet 1431
Safe working in confined spaces see information sheet 1433Directives for ventilation practice see information sheet 1434
Cleaning of steel and removal of rust see information sheet 1490Specification for mineral abrasives see information sheet 1491
Relative humidity - substrate temperature -air temperature see information sheet 1650
for paint and recommended thinners see safety sheets 1430, 1431 andrelevant material safety data sheets
although this is a solvent free paint, care should be taken to avoid inhalationof spray mist as well as contact between the wet paint and exposed skin or
eyes no solvent present; however, spray mist is not harmless, a fresh air mask
should be used during spraying ventilation should be provided in confined spaces to maintain good
visibility
REFERENCES
SAFETY PRECAUTIONS
7/22/2019 Sigma Coating s
34/1103
September 2013
page 5/5
NOVAGUARD 890
WARRANTY
PPG warrants (i) its title to the product, (ii) that the quality of the product conforms to PPGs specifications for such product
in effect at the time of manufacture and (iii) that the product shall be delivered free of the rightful claim of any third person for
infringement of any U.S. patent covering the product. THESE ARE THE ONLY WARRANTIES THAT PPG MAKES AND ALL
OTHER EXPRESS OR IMPLIED WARRANTIES, UNDER STATUTE OR ARISING OTHERWISE IN LAW, FROM A COURSE
OF DEALING OR USAGE OF TRADE, INCLUDING WITHOUT LIMITATION, ANY OTHER WARRANTY OF FITNESS FOR A
PARTICULAR PURPOSE OR USE, ARE DISCLAIMED BY PPG. Any claim under this warranty must be made by Buyer to PPG
in writing within five (5) days of Buyers discovery of the claimed defect, but in no event later than the expiration of the applicable
shelf life of the product, or one year from the date of the delivery of the product to the Buyer, whichever is earlier. Buyers failure
to notify PPG of such non-conformance as required herein shall bar Buyer from recovery under this warranty.
LIMITATIONS OF LIABILITY
IN NO EVENT WILL PPG BE LIABLE UNDER ANY THEORY OF RECOVERY (WHETHER BASED ON NEGLIGENCE
OF ANY KIND, STRICT LIABILITY OR TORT) FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES IN ANY WAY RELATED TO, ARISING FROM, OR RESULTING FROM ANY USE MADE OF THE PRODUCT.
The information in t his sheet is i ntended for guidance only and i s based upon laboratory tests that PPG believes to
be reliable. PPG may modify the information contained herein at any time as a result of practical experience and
continuous product development. All recommendations or suggestions relating to t he use of the PPG product,
whether in technical documentation, or in response to a specific inqu iry, or otherwise, are based on data, which to the
best of PPGs knowledge, is reliable. The product and related information is designed for users having the requisi te
knowledge and industrial skills i n the industry and it is the end-users responsibility to determine the suitability of
the product for its own particular use and it shall be deemed that Buyer has done so, as its sole discretion and risk.
PPG has no control over either the quality or condition of the substrate, or the many factors affecting the use and
application of the product. Therefore, PPG does not accept any liability arising from any loss, injury or damage
resulting from such use or the contents of this inf ormation (unless there are written agreements stating otherwise).
Variations in the application environment, changes in procedures of use, or extrapolation of data may cause
unsatisfactory results. This sheet supersedes all previous versions and it i s the Buyers responsibili ty to ensure that
this i nformation is current prior t o using the product. Current sheets for all PPG Protective & Marine Coatings Products
are maintained at www.ppgpmc.com. The English text of this sheet shall prevail over any translation thereof.
PDS 7755
269264 green 4194542200
282887 cream 3002002200
7/22/2019 Sigma Coating s
35/1103
7/22/2019 Sigma Coating s
36/1103
November 2012
page 1/4
4 pages
Revision of September 2011
Phenguard 253
two component high build amine adduct cured novolac phenolic epoxy primer
excellent resistance to a wide range of organic acids, alcohols, edible oils
and solvents maximum cargo flexibility
low cargo absorbtion recognized corrosion control coating (Lloyds register) See sheet 1886
good application properties, resulting in a smooth surface
grey, offwhite semigloss
(1 g/cm = 8.35 lb/US gal; 1 m/l = 40.7 ft/US gal)
(data for mixed product)
1.4 g/cm ( mixed product )72% 3%
max. 200 g/l (approx. 1.7 lb/gal)(UK PG 6/23(92) Appendix 3)
Recommended dry film thickness 125 - 150 m
Theoretical spreading rate 7.2 m/l for 100 mmin.10 hours*
max. 5 days *at least 12 months
* see additional data
steel; blast cleaned in situ to at least ISO-Sa2 and free from rust, scale,
shop primer and any other contamination blasting profile 50 - 100 m
the substrate must be perfectly dry before and during application ofPhenguard 253
substrate temperature must be above 10C and at least 3C above dewpoint during application and curing
mixing ratio by volume: base to hardener 80 : 20
the temperature of the paint should preferably be above 15C, otherwise
extra thinner may be required to obtain application viscosity
too much solvent results in reduced sag resistance and slower cure thinner should be added after mixing the components
allow induction time before use15C - 45 min.
20C - 30 min.25C - 15 min.
4 hours at 21.1C / 70F
* see additional data
Description
PRINCIPAL CHARACTERISTICS
COLOURS AND GLOSS
BASIC DATA AT 20 C
Mass densityVolume solids
VOC (UK PG 6/23(92) appendix 3)
Overcoating interval
Shelf life (cool and dry place)
RECOMMENDED
SUBSTRATE CONDITIONSAND TEMPERATURES
INSTRUCTIONS FOR USE
Induction time
Pot life
7/22/2019 Sigma Coating s
37/1103
November 2012
page 2/4
Phenguard 253
Recommended thinner Thinner 91-92
Volume of thinner 5 - 10%, depending on required thickness and application conditions
Nozzle orifice 2 mm
Nozzle pressure 0.3 MPa (= approx. 3 bar; 44 p.s.i.)
Recommended thinner Thinner 91-92
Volume of thinner 5 - 10%, depending on required thickness and application conditions
Nozzle orifice approx. 0.46 - 0.53 mm (= 0.018 - 0.021 in)
Nozzle pressure 15 - 15 MPa (= approx. 150 - 150 bar; 2176 - 2176 p.s.i.)
only for touch up and spot repairRecommended thinner Thinner 91-92
Volume of thinner 0 - 5%
Thinner 90-53
Film thickness and spreading rate
theoritical spreading rate m2/l 7.2 4.8
dft in m 100 150
Overcoating tabel for Phenguard 253
substratetemperature
10C 15C 20C 30C 40C
minimum interval 24 hours 16 hours 10 hours 4 hours 3 hours
maximum interval 7 days 6 days 5 days 4 days 3 days
surface should be dry and free from any contamination
Curing table
substrate temperature Service
10C 14 day
15C 10 days
20C 7 days
30C 4 days
40C 4 days
minimum curing time of Phenguard 253 tank coating systems before the transport of
cargoes
please contact your PPG representative for further details
AIR SPRAY
AIRLESS SPRAY
BRUSH/ROLLER
CLEANING SOLVENT
ADDITIONAL DATA
Curing
7/22/2019 Sigma Coating s
38/1103
November 2012
page 3/4
Phenguard 253
Pot life (at application viscos ity)
10C 6 hours
20 C 4 hours
30 C 2 hours
Whilst it is always the aim of Sigma Coatings to supply the same product on a
worldwide basis, slight modification of the product is sometimes necessary tocomply with local or national rules/circumstances.
Under these circumstances an alternative product data sheet is used.
Explanation to product data sheets see information sheet 1411
Safety indications see information sheet 1430Safety in confined spaces and health safety
Explosion hazard - toxic hazard see information sheet 1431Safe working in confined spaces see information sheet 1433
Directives for ventilation practice see information sheet 1434Cleaning of steel and removal of rust see information sheet 1490
Specification for mineral abrasives see information sheet 1491
for paint and recommended thinners see safety sheets 1430, 1431 andrelevant material safety data sheets
This is a solvent borne paint and care should be taken to avoid inhalationof spray mist or vapour as well as contact between the wet paint and
exposed skin or eyes
Worldwide availability
REFERENCES
SAFETY PRECAUTIONS
7/22/2019 Sigma Coating s
39/1103
November 2012
page 4/4
Phenguard 253
LIMITATIONS OF LIABILITY
IN NO EVENT WILL PPG BE LIABLE UNDER ANY THEORY OF RECOVERY (WHETHER BASED ON NEGLIGENCE
OF ANY KIND, STRICT LIABILITY OR TORT) FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES IN ANY WAY RELATED TO, ARISING FROM, OR RESULTING FROM ANY USE MADE OF THE PRODUCT.
The information in t his sheet is i ntended for guidance only and i s based upon laboratory tests that PPG believes to
be reliable. PPG may modify the information contained herein at any time as a result of practical experience and
continuous product development. All recommendations or suggestions relating to t he use of the PPG product,
whether in technical documentation, or in response to a specific inqu iry, or otherwise, are based on data, which to the
best of PPGs knowledge, is reliable. The product and related information is designed for users having the requisi te
knowledge and industrial skills i n the industry and it is the end-users responsibility to determine the suitability of
the product for its own particular use and it shall be deemed that Buyer has done so, as its sole discretion and risk.
PPG has no control over either the quality or condition of the substrate, or the many factors affecting the use and
application of the product. Therefore, PPG does not accept any liability arising from any loss, injury or damage
resulting from such use or the contents of this inf ormation (unless there are written agreements stating otherwise).
Variations in the application environment, changes in procedures of use, or extrapolation of data may cause
unsatisfactory results. This sheet supersedes all previous versions and it i s the Buyers responsibili ty to ensure that
this i nformation is current prior t o using the product. Current sheets for all PPG Protective & Marine Coatings Products
are maintained at www.ppgpmc.com. The English text of this sheet shall prevail over any translation thereof.
PDS 7447
7/22/2019 Sigma Coating s
40/1103
July 2012
page 1/5
5 pages
Revision of March 2011
PHENGUARD 930
two component high build amine adduct cured novolac phenolic epoxy primer
primer coat in the Phenguard tankcoating system
excellent resistance to a wide range of organic acids, alcohols, edible oils,fats (regardless of free fatty acid content) and solvents
maximum cargo flexibility low cargo absorption
good resistance to hot water recognized corrosion control coating (Lloyd's register), see sheet 1886
good application properties, resulting in a smooth surface
offwhite eggshell
(1 g/cm = 8.35 lb/US gal; 1 m/l = 40.7 ft/US gal)
(data for mixed product)
1.7 g/cm66% 2%
max. 191 g/kg (Directive 1999/13/EC, SED)max. 315 g/l (approx. 2.6 lb/gal)
(UK PG 6/23(92) Appendix 3)Recommended dry film thickness 100 m *
Theoretical spreading rate 6.6 m/l for 100 m *2 hours at 20 C
min. 36 hours *
max. 21 days *
see curing table *at least 12 months* see additional data
steel; blast cleaned in situ to at least ISO-Sa2 and free from rust, scale,shop primer and any other contamination
blasting profile 50 - 100 m the substrate must be perfectly dry before and during application of
Phenguard 930 substrate temperature must be above 10C and at least 3C above dew
point during application and curing
marine system sheet: 3141
tankcoatings system sheet: 3322
Description
PRINCIPAL CHARACTERISTICS
COLOURS AND GLOSS
BASIC DATA AT 20 C
Mass densityVolume solids
VOC (Directive 1999/13/EC, SED)VOC (UK PG 6/23(92) appendix 3)
Touch dry after
Overcoating interval
Full cure afterShelf life (cool and dry place)
RECOMMENDEDSUBSTRATE CONDITIONS
AND TEMPERATURES
SYSTEM SPECIFICATION
7/22/2019 Sigma Coating s
41/1103
July 2012
page 2/5
PHENGUARD 930
mixing ratio by volume: base to hardener 88 : 12
the temperature of the mixed base and hardener should preferably be
above 15C, otherwise extra solvent may be required to obtain applicationviscosity
too much solvent results in reduced sag resistance and slower cure thinner should be added after mixing the components
4 hours at 20 C * allow induction time before use
15C - 20 min. 20C - 15 min.
25C - 10 min.
Recommended thinner Thinner 91-92
Volume of thinner 0 - 10%, depending on required thickness and application conditions
Nozzle orifice 2 mm
Nozzle pressure 0.3 MPa (= approx. 3 bar; 44 p.s.i.)
Recommended thinner Thinner 91-92
Volume of thinner 0 - 10%, depending on required thickness and application conditions
Nozzle orifice approx. 0.46 - 0.53 mm (= 0.018 - 0.021 in)Nozzle pressure 15 MPa (= approx. 150 bar; 2176 p.s.i.)
only for spot repair and stripe coatingRecommended thinner Thinner 91-92
Volume of thinner 0 - 5%
Thinner 90-53
Film thickness and spreading rate
theoritical spreading rate m2/l 6.6 5.3
dft in m 100 125
Maximum dft when brushing: 60 m
Overcoating table for Phenguard 935
substrate
temperature
10C 15C 20C 30C 40C
minimum interval 60 hours 48 hours 36 hours 24 hours 16 hours
maximum interval 28 days 25 days 21 days 14 days 7 days
surface should be dry and free from any contamination
INSTRUCTIONS FOR USE
Pot lifeInduction time
AIR SPRAY
AIRLESS SPRAY
BRUSH/ROLLER
CLEANING SOLVENT
7/22/2019 Sigma Coating s
42/1103
July 2012
page 3/5
PHENGUARD 930
Curing table for Phenguard tankcoating system before transport of
cargoes without note 4, 7, 8 or 11 and ballast water and tanktest with seawater
substrate temperature Service
10C 14 days
15C 14 days
20C 10 days
30C 7 days
40C 5 days
minimum curing time of Phenguard tankcoating system before transport of
cargoes with note 4, 7, 8 or 11: 3 months for detailed information on resistance and resistance notes, please refer to
the latest issue of the Cargo Resistance List for transport of methanol and vinyl acetate monomer, a hot cure is required
which cannot be substituted by a service period of 3 months with non-aggressive cargoes
adequate ventilation must be maintained during application and curing(please refer to sheets 1433 and 1434)
the performance of the applied system strongly depends on the curingdegree of the first coat at time of recoating. Therefore overcoating time
between 1st and 2nd coat is extended in comparison between 2nd and 3rdcoat (see overcoating details)
when used as a primer under solvent free tank-linings the dft must be limitedto a maximum of 100 m
Pot life (at application viscos ity)
10 C 6 hours
20 C 4 hours
30 C 1.5 hour
Whilst it is always the aim of Sigma Coatings to supply the same product on aworldwide basis, slight modification of the product is sometimes necessary to
comply with local or national rules/circumstances.Under these circumstances an alternative product data sheet is used.
Curing
Worldwide availability
7/22/2019 Sigma Coating s
43/1103
July 2012
page 4/5
PHENGUARD 930
Conversion tabels see information sheet 1410
Explanation to product data sheets see information sheet 1411Safety indications see information sheet 1430
Safety in confined spaces and health safetyExplosion hazard - toxic hazard see information sheet 1431
Safe working in confined spaces see information sheet 1433Directives for ventilation practice see information sheet 1434
Cleaning of steel and removal of rust see information sheet 1490Specification for mineral abrasives see information sheet 1491
Relative humidity - substrate temperature -air temperature see information sheet 1650
for paint and recommended thinners see safety sheets 1430, 1431 andrelevant material safety data sheets
this is a solvent borne paint and care should be taken to avoid inhalation ofspray mist or vapour as well as contact between the wet paint and exposed
skin or eyes
REFERENCES
SAFETY PRECAUTIONS
7/22/2019 Sigma Coating s
44/1103
July 2012
page 5/5
PHENGUARD 930
WARRANTY
PPG warrants (i) its title to the product, (ii) that the quality of the product conforms to PPGs specifications for such product
in effect at the time of manufacture and (iii) that the product shall be delivered free of the rightful claim of any third person for
infringement of any U.S. patent covering the product.
THESE ARE THE ONLY WARRANTIES THAT PPG MAKES AND ALL OTHER EXPRESS OR IMPLIED WARRANTIES,
UNDER STATUTE OR ARISING OTHERWISE IN LAW, FROM A COURSE OF DEALING OR USAGE OF TRADE,
INCLUDING WITHOUT LIMITATION, ANY OTHER WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE OR USE, ARE
DISCLAIMED BY PPG.
Any claim under this warranty must be made by Buyer to PPG in writing within five (5) days of Buyers discovery of the claimed
defect, but in no event later than the expiration of the applicable shelf life of the product, or one year from the date of the
delivery of the product to the Buyer, whichever is earlier. Buyers failure to notify PPG of such non-conformance as required
herein shall bar Buyer from recovery under this warranty.
LIMITATIONS OF LIABILITY
IN NO EVENT WILL PPG BE LIABLE UNDER ANY THEORY OF RECOVERY (WHETHER BASED ON NEGLIGENCE OF
ANY KIND, STRICT LIABILITY OR TORT) FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES
IN ANY WAY RELATED TO, ARISING FROM, OR RESULTING FROM ANY USE MADE OF THE PRODUCT.
The information in this data sheet is intended for guidance only and is based upon laboratory tests that PPG believes
to be reliable. PPG may modify the information contained herein at any time as a result of practi cal experience and
continuous product development. All recommendations or suggestions relating to t he use of the PPG product,
whether in technical documentation, or in response to a specific inqu iry, or otherwise, are based on data, which to the
best of PPGs knowledge, is reliable. The product and related information is designed for users having the requisi te
knowledge and industrial skills i n the industry and it is the end-users responsibility to determine the suitability of the
product for its own particular use and it shall be deemed that Buyer has done so, as its sole discretion and risk.
PPG has no control over either the quality or condition of the substrate, or the many factors affecting the use and
application of the product. Therefore, PPG does not accept any liability arising from any loss, injury or damage
resulting from such use or the contents of this data sheet (unless there are written agreements stating otherwise).Variations in the application environment, changes in procedures of use, or extrapolation of data may cause
unsatisfactory results.
This data sheet supersedes all previous versions and it is the Buyers r esponsibility to ensure that this data sheet
is current prior to using the product. Current data sheets for all PPG Protective & Marine Coatings products are
maintained at www.ppgpmc.com.
The English text of this data sheet shall prevail over any translation thereof.
PDS 7409
180706 offwhite 7001002200
7/22/2019 Sigma Coating s
45/1103
7/22/2019 Sigma Coating s
46/1103
November 2012
page 1/5
5 pages
Revision of July 2012
PHENGUARD 935
two component high build amine adduct cured novolac phenolic epoxy coating
second coat in the Phenguard tankcoating system
excellent resistance to a wide range of organic acids, alcohols, edible oils,fats (regardless of free fatty acid content) and solvents
maximum cargo flexibility low cargo absorption
good resistance to hot water recognized corrosion control coating (Lloyd's register), see sheet 1886
good application properties, resulting in a smooth surface
pink eggshell
(1 g/cm = 8.35 lb/US gal; 1 m/l = 40.7 ft/US gal)
(data for mixed product)
1.7 g/cm66% 2%
max. 191 g/kg (Directive 1999/13/EC, SED)max. 315 g/l (approx. 2.6 lb/gal)
Recommended dry film thickness 100 m *Theoretical spreading rate 6.6 m/l for 100 m *
2 hours at 20 Cmin. 24 hours *
max. 21 days *see curing table *
(data for components)
at least 12 months* see additional data
previous coat of Phenguard 930; dry and free from any contamination
the substrate must be perfectly dry before and during application of
Phenguard 935
substrate temperature must be above 10C and at least 3C above dewpoint during application and curing
marine system sheet: 3141tankcoatings system sheet: 3322
Description
PRINCIPAL CHARACTERISTICS
COLOURS AND GLOSS
BASIC DATA AT 20 C
Mass densityVolume solids
VOC (Directive 1999/13/EC, SED)VOC (UK PG 6/23(92) appendix 3)
Touch dry afterOvercoating interval
Full cure after
Shelf life (cool and dry place)
RECOMMENDED
SUBSTRATE CONDITIONS
AND TEMPERATURES
SYSTEM SPECIFICATION
7/22/2019 Sigma Coating s
47/1103
November 2012
page 2/5
PHENGUARD 935
mixing ratio by volume: base to hardener 88 : 12
the temperature of the mixed base and hardener should preferably beabove 15C, otherwise extra solvent may be required to obtain application
viscosity too much solvent results in reduced sag resistance and slower cure
thinner should be added after mixing the components
allow induction time before use15C - 20 min.
20C - 15 min.25C - 10 min.
4 hours at 20 C*see additional data
Recommended thinner Thinner 91-92
Volume of thinner 0 - 10%, depending on required thickness and application conditions
Nozzle orifice 2 mm
Nozzle pressure 0.3 MPa (= approx. 3 bar; 44 p.s.i.)
Recommended thinner Thinner 91-92Volume of thinner 0 - 10%, depending on required thickness and application conditions
Nozzle orifice approx. 0.46 - 0.53 mm (= 0.018 - 0.021 in)
Nozzle pressure 15 MPa (= approx. 150 bar; 2176 p.s.i.)
Recommended thinner Thinner 91-92
Volume of thinner 0 - 5%
Thinner 90-53
Film thickness and spreading rate
theoritical spreading rate m/l 6.6 5.3
dft in m 100 125
Maximum dft when brushing: 60 m
INSTRUCTIONS FOR USE
Induction time
Pot life
AIR SPRAY
AIRLESS SPRAY
BRUSH/ROLLER
CLEANING SOLVENT
7/22/2019 Sigma Coating s
48/1103
November 2012
page 3/5
PHENGUARD 935
Overcoating table for Phenguard 935
substratetemperature
10C 15C 20C 30C 40C
minimum interval 36 hours 32 hours 24 hours 16 hours 12 hours
maximum interval 28 days 25 days 21 days 14 days 7 days
surface should be dry and free from any contamination
Min.curing time of Phenguard tankcoating system before transport of
cargoes without note 4, 7, 8 or 11 and ballast water and tanktest with sea
water
substrate temperature Service
10C 14 days
15C 14 days
20C 10 days
30C 7 days
40C 5 days
minimum curing time of Phenguard tankcoating system before transport of
cargoes with note 4, 7, 8 or 11: 3 months for detailed information on resistance and resistance notes, please refer to
the latest issue of the Cargo Resistance List
for transport of methanol and vinyl acetate monomer, a hot cure is requiredwhich cannot be substituted by a service period of 3 months with non-
aggressive cargoes adequate ventilation must be maintained during application and curing
(please refer to sheets 1433 and 1434) the performance of the applied system strongly depends on the curing
degree of the first coat at time of recoating. Therefore overcoating timebetween 1st and 2nd coat is extended in comparison between 2nd and 3rd
coat (see overcoating details)
Pot life (at application viscos ity)
10 C 6 hours
20 C 4 hours
30 C 1.5 hour
Curing
7/22/2019 Sigma Coating s
49/1103
November 2012
page 4/5
PHENGUARD 935
It is always the aim of PPG Protective and Marine Coatings to supply the same
product on a worldwide basis. However, slight modification of the product issometimes necessary to comply with local or national rules/circumstances.
Under these circumstances an alternative product data sheet is used
Conversion tabels see information sheet 1410Explanation to product data sheets see information sheet 1411
Safety indications see information sheet 1430Safety in confined spaces and health safety
Explosion hazard - toxic hazard see information sheet 1431Safe working in confined spaces see information sheet 1433
Directives for ventilation practice see information sheet 1434
Cleaning of steel and removal of rust see information sheet 1490Specification for mineral abrasives see information sheet 1491
Relative humidity - substrate temperature -air temperature see information sheet 1650
for paint and recommended thinners see safety sheets 1430, 1431 and
relevant material safety data sheets this is a solvent borne paint and care should be taken to avoid inhalation of
spray mist or vapour as well as contact between the wet paint and exposedskin or eyes
Worldwide availability
REFERENCES
SAFETY PRECAUTIONS
7/22/2019 Sigma Coating s
50/1103
November 2012
page 5/5
PHENGUARD 935
WARRANTY
PPG warrants (i) its title to the product, (ii) that the quality of the product conforms to PPGs specifications for such product
in effect at the time of manufacture and (iii) that the product shall be delivered free of the rightful claim of any third person for
infringement of any U.S. patent covering the product. THESE ARE THE ONLY WARRANTIES THAT PPG MAKES AND ALL
OTHER EXPRESS OR IMPLIED WARRANTIES, UNDER STATUTE OR ARISING OTHERWISE IN LAW, FROM A COURSE
OF DEALING OR USAGE OF TRADE, INCLUDING WITHOUT LIMITATION, ANY OTHER WARRANTY OF FITNESS FOR A
PARTICULAR PURPOSE OR USE, ARE DISCLAIMED BY PPG. Any claim under this warranty must be made by Buyer to PPG
in writing within five (5) days of Buyers discovery of the claimed defect, but in no event later than the expiration of the applicable
shelf life of the product, or one year from the date of the delivery of the product to the Buyer, whichever is earlier. Buyers failure
to notify PPG of such non-conformance as required herein shall bar Buyer from recovery under this warranty.
LIMITATIONS OF LIABILITY
IN NO EVENT WILL PPG BE LIABLE UNDER ANY THEORY OF RECOVERY (WHETHER BASED ON NEGLIGENCE
OF ANY KIND, STRICT LIABILITY OR TORT) FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES IN ANY WAY RELATED TO, ARISING FROM, OR RESULTING FROM ANY USE MADE OF THE PRODUCT.
The information in t his sheet is i ntended for guidance only and i s based upon laboratory tests that PPG believes to
be reliable. PPG may modify the information contained herein at any time as a result of practical experience and
continuous product development. All recommendations or suggestions relating to t he use of the PPG product,
whether in technical documentation, or in response to a specific inqu iry, or otherwise, are based on data, which to the
best of PPGs knowledge, is reliable. The product and related information is designed for users having the requisi te
knowledge and industrial skills i n the industry and it is the end-users responsibility to determine the suitability of
the product for its own particular use and it shall be deemed that Buyer has done so, as its sole discretion and risk.
PPG has no control over either the quality or condition of the substrate, or the many factors affecting the use and
application of the product. Therefore, PPG does not accept any liability arising from any loss, injury or damage
resulting from such use or the contents of this inf ormation (unless there are written agreements stating otherwise).
Variations in the application environment, changes in procedures of use, or extrapolation of data may cause
unsatisfactory results. This sheet supersedes all previous versions and it i s the Buyers responsibili ty to ensure that
this i nformation is current prior t o using the product. Current sheets for all PPG Protective & Marine Coatings Products
are maintained at www.ppgpmc.com. The English text of this sheet shall prevail over any translation thereof.
PDS 7435
179115 pink 6007002200
7/22/2019 Sigma Coating s
51/1103
7/22/2019 Sigma Coating s
52/1103
July 2012
page 1/5
5 pages
Revision of March 2011
PHENGUARD 940
two component high build amine adduct cured novolac phenolic epoxy finish
finish coat in the Phenguard tankcoating system
excellent resistance to a wide range of organic acids, alcohols, edible oils,fats (regardless of free fatty acid content) and solvents
maximum cargo flexibility low cargo absorption
good resistance to hot water recognized corrosion control coating (Lloyd's register), see sheet 1886
good application properties, resulting in a smooth surface easy to clean
light grey eggshell
(1 g/cm = 8.35 lb/US gal; 1 m/l = 40.7 ft/US gal)
(data for mixed product)
1.7 g/cm
66% 2%max. 191 g/kg (Directive 1999/13/EC, SED)
max. 315 g/l (approx. 2.6 lb/gal)Recommended dry film thickness 100 m *
Theoretical spreading rate 6.6 m/l for 100 m *2 hours at 20 C
min. 24 hours *
max. 21 days *
see curing table * at 20 C* see additional data
at least 12 months* see additional data
previous coat of Phenguard 935; dry and free from any contamination the substrate must be perfectly dry before and during application of
Phenguard 940 substrate temperature must be above 10C and at least 3C above dew
point during application and curing
Description
PRINCIPAL CHARACTERISTICS
COLOURS AND GLOSS
BASIC DATA AT 20 C
Mass density
Volume solidsVOC (Directive 1999/13/EC, SED)
VOC (UK PG 6/23(92) appendix 3)
Touch dry after
Overcoating interval
Full cure after
Shelf life (cool and dry place)
RECOMMENDEDSUBSTRATE CONDITIONS
AND TEMPERATURES
7/22/2019 Sigma Coating s
53/1103
July 2012
page 2/5
PHENGUARD 940
marine system sheet: 3141
tankcoatings system sheet: 3322
mixing ratio by volume: base to hardener 88 : 12 the temperature of the mixed base and hardener should preferably be
above 15C, otherwise extra solvent may be required to obtain applicationviscosity
too much solvent results in reduced sag resistance and slower cure thinner should be added after mixing the components
4 hours at 20 C **see additional data
allow induction time before use
15C - 20 min. 20C - 15 min.
25C - 10 min.
Recommended thinner Thinner 91-92
Volume of thinner 0 - 10%, depending on required thickness and application conditions
Nozzle orifice 2 mm
Nozzle pressure 0.3 MPa (= approx. 3 bar; 44 p.s.i.)
Recommended thinner Thinner 91-92
Volume of thinner 0 - 10%, depending on required thickness and application conditions
Nozzle orifice approx. 0.46 - 0.53 mm (= 0.018 - 0.021 in)
Nozzle pressure 15 MPa (= approx. 150 bar; 2176 p.s.i.)
Recommended thinner Thinner 91-92
Volume of thinner 0 - 5%
Thinner 90-53
Film thickness and spreading rate
theoritical spreading rate m2/l 6.6 5.3
dft in m 100 125
Maximum dft when brushing: 60 m
SYSTEM SPECIFICATION
INSTRUCTIONS FOR USE
Pot life
Induction time
AIR SPRAY
AIRLESS SPRAY
BRUSH/ROLLER
CLEANING SOLVENT
7/22/2019 Sigma Coating s
54/1103
July 2012
page 3/5
PHENGUARD 940
Overcoating table for Phenguard 940
substratetemperature
10C 15C 20C 30C 40C
minimum interval 36 hours 32 hours 24 hours 16 hours 12 hours
maximum interval 28 days 25 days 21 days 14 days 7 days
surface should be dry and free from any contamination
Min.curing time of Phenguard tankcoating system before transport of
cargoes without note 4, 7, 8 or 11 and ballast water and tanktest with sea
water
substrate temperature Service
10C 14 days
15C 14 days
20C 10 days
30C 7 days
40C 5 days
minimum curing time of Phenguard tankcoating system before transport of
cargoes with note 4, 7, 8 or 11: 3 months for detailed information on resistance and resistance notes, please refer to
the latest issue of the Cargo Resistance List
for transport of methanol and vinyl acetate monomer, a hot cure is requiredwhich cannot be substituted by a service period of 3 months with non-
aggressive cargoes adequate ventilation must be maintained during application and curing
(please refer to sheets 1433 and 1434) the performance of the applied system strongly depends on the curing
degree of the first coat at time of recoating. Therefore overcoating timebetween 1st and 2nd coat is extended in comparison between 2nd and 3rd
coat (see overcoating details)
Pot life (at application viscos ity)
10 C 6 hours
20 C 4 hours
30 C 1.5 hour
Whilst it is always the aim of Sigma Coatings to supply the same product on a
worldwide basis, slight modification of the product is sometimes necessary tocomply with local or national rules/circumstances.
Under these circumstances an alternative product data sheet is used.
Curing
Worldwide availability
7/22/2019 Sigma Coating s
55/1103
July 2012
page 4/5
PHENGUARD 940
Conversion tabels see information sheet 1410
Explanation to product data sheets see information sheet 1411Safety indications see information sheet 1430
Safety in confined spaces and health safetyExplosion hazard - toxic hazard see information sheet 1431
Safe working in confined spaces see information sheet 1433Directives for ventilation practice see information sheet 1434
Cleaning of steel and removal of rust see information sheet 1490Specification for mineral abrasives see information sheet 1491
Relative humidity - substrate temperature -air temperature see information sheet 1650
for paint and recommended thinners see safety sheets 1430, 1431 andrelevant material safety data sheets
this is a solvent borne paint and care should be taken to avoid inhalation ofspray mist or vapour as well as contact between the wet paint and exposed
skin or eyes
REFERENCES
SAFETY PRECAUTIONS
7/22/2019 Sigma Coating s
56/1103
July 2012
page 5/5
PHENGUARD 940
WARRANTY
PPG warrants (i) its title to the product, (ii) that the quality of the product conforms to PPGs specifications for such product
in effect at the time of manufacture and (iii) that the product shall be delivered free of the rightful claim of any third person for
infringement of any U.S. patent covering the product.
THESE ARE THE ONLY WARRANTIES THAT PPG MAKES AND ALL OTHER EXPRESS OR IMPLIED WARRANTIES,
UNDER STATUTE OR ARISING OTHERWISE IN LAW, FROM A COURSE OF DEALING OR USAGE OF TRADE,
INCLUDING WITHOUT LIMITATION, ANY OTHER WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE OR USE, ARE
DISCLAIMED BY PPG.
Any claim under this warranty must be made by Buyer to PPG in writing within five (5) days of Buyers discovery of the claimed
defect, but in no event later than the expiration of the applicable shelf life of the product, or one year from the date of the
delivery of the product to the Buyer, whichever is earlier. Buyers failure to notify PPG of such non-conformance as required
herein shall bar Buyer from recovery under this warranty.
LIMITATIONS OF LIABILITY
IN NO EVENT WILL PPG BE LIABLE UNDER ANY THEORY OF RECOVERY (WHETHER BASED ON NEGLIGENCE OF
ANY KIND, STRICT LIABILITY OR TORT) FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES
IN ANY WAY RELATED TO, ARISING FROM, OR RESULTING FROM ANY USE MADE OF THE PRODUCT.
The information in this data sheet is intended for guidance only and is based
Top Related