Sigma Coating s

7/22/2019 Sigma Coating s

1/1103


2/1103


3/1103


4/1103


5/1103


6/1103


7/1103


8/1103

March 2013

page 1/3

3 pages

Revision of September 2004

FLUORGUARD 7000

two component, air drying, fluoropolymer based topcoat with excellent weather

resistance and color retention

excellent resistance to atmospheric exposure conditions very good colour and gloss retention

excellent resistance to chemical, acid, alkali can be applied by airless spray, roller and brush

colours available on request gloss

1.2 g/cm

approx. 36% by volumeRecommended dry film thickness 20 - 40 m

Theoretical spreading rate 18.0 m/l for 20 m9.0 m/l for 40 m

1 hours at 20 Cmin.5 hours at 20 C

max. unlimited12 months

previous coat; dry and free from any contamination

substrate temperature should be at least 3C above dew point maximum relative humidity during application and curing is 85%

mixing ratio by volume: base to hardener 7:1

mix thoroughly by a mechanical mixer before application Agitate continuously during application

none5 hours at 20 C

Recommended thinner Thinner 21-06Volume of thinner 5 - 10%

Nozzle orifice approx. 1.0 - 1.5 mm (= 0.039 - 0.059 in)

Nozzle pressure 30 - 40 MPa (= approx. 300 - 400 bar; 4351 - 5802 p.s.i.)

Recommended thinner Thinner 21-06

Volume of thinner 0 - 5%



Recommended thinner Thinner 21-06Volume of thinner 0 - 3%

Description

PRINCIPAL CHARACTERISTICS

COLOURS AND GLOSS

BASIC DATA

Mass densityVolume solids

Touch dry afterOvercoating interval

Shelf life (cool and dry place)

RECOMMENDED

SUBSTRATE CONDITIONSAND TEMPERATURES

INSTRUCTIONS FOR USE

Induction timePot life

AIR SPRAY

AIRLESS SPRAY

BRUSH/ROLLER


9/1103

March 2013

page 2/3

FLUORGUARD 7000

Thinner 21-06

It is always the aim of PPG Protective and Marine Coatings to supply the same

product on a worldwide basis. However, slight modification of the product issometimes necessary to comply with local or national rules/circumstances.

Under these circumstances an alternative product data sheet is used

Explanation to product data sheets see information sheet 1411Safety indications see information sheet 1430

Safety in confined spaces and health safetyExplosion hazard - toxic hazard see information sheet 1431

for paint and recommended thinners see safety sheets 1430, 1431 andrelevant material safety data sheets

CLEANING SOLVENT

Worldwide availability

REFERENCES

SAFETY PRECAUTIONS


10/1103

March 2013

page 3/3

FLUORGUARD 7000

WARRANTY

PPG warrants (i) its title to the product, (ii) that the quality of the product conforms to PPGs specifications for such product

in effect at the time of manufacture and (iii) that the product shall be delivered free of the rightful claim of any third person for

infringement of any U.S. patent covering the product. THESE ARE THE ONLY WARRANTIES THAT PPG MAKES AND ALL

OTHER EXPRESS OR IMPLIED WARRANTIES, UNDER STATUTE OR ARISING OTHERWISE IN LAW, FROM A COURSE

OF DEALING OR USAGE OF TRADE, INCLUDING WITHOUT LIMITATION, ANY OTHER WARRANTY OF FITNESS FOR A

PARTICULAR PURPOSE OR USE, ARE DISCLAIMED BY PPG. Any claim under this warranty must be made by Buyer to PPG

in writing within five (5) days of Buyers discovery of the claimed defect, but in no event later than the expiration of the applicable

shelf life of the product, or one year from the date of the delivery of the product to the Buyer, whichever is earlier. Buyers failure

to notify PPG of such non-conformance as required herein shall bar Buyer from recovery under this warranty.

LIMITATIONS OF LIABILITY

IN NO EVENT WILL PPG BE LIABLE UNDER ANY THEORY OF RECOVERY (WHETHER BASED ON NEGLIGENCE

OF ANY KIND, STRICT LIABILITY OR TORT) FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL

DAMAGES IN ANY WAY RELATED TO, ARISING FROM, OR RESULTING FROM ANY USE MADE OF THE PRODUCT.

The information in t his sheet is i ntended for guidance only and i s based upon laboratory tests that PPG believes to

be reliable. PPG may modify the information contained herein at any time as a result of practical experience and

continuous product development. All recommendations or suggestions relating to t he use of the PPG product,

whether in technical documentation, or in response to a specific inqu iry, or otherwise, are based on data, which to the

best of PPGs knowledge, is reliable. The product and related information is designed for users having the requisi te

knowledge and industrial skills i n the industry and it is the end-users responsibility to determine the suitability of

the product for its own particular use and it shall be deemed that Buyer has done so, as its sole discretion and risk.

PPG has no control over either the quality or condition of the substrate, or the many factors affecting the use and

application of the product. Therefore, PPG does not accept any liability arising from any loss, injury or damage

resulting from such use or the contents of this inf ormation (unless there are written agreements stating otherwise).

Variations in the application environment, changes in procedures of use, or extrapolation of data may cause

unsatisfactory results. This sheet supersedes all previous versions and it i s the Buyers responsibili ty to ensure that

this i nformation is current prior t o using the product. Current sheets for all PPG Protective & Marine Coatings Products

are maintained at www.ppgpmc.com. The English text of this sheet shall prevail over any translation thereof.

PDS 8570


11/1103


12/1103

HI-TEMP COATINGS TECHNOLOGY P.O. Box 2347 Acton, MA 01720Tel: 978-635-1110 Fax: 978-635-1124 [email protected] www.hitempcoatings.com

Rev. 090412 Page 1 of 4

Hi-Temp 1027- CUI Prevents Corrosion Under Insulation- Stainless Steel Prevents Stress Corrosion Cracking- DTR Direct to Tight, Adherent Rust Application- Primer High Build, High Solids- Cryogenic Protects Cryogenic Equipment

PRODUCT DESCRIPTION:Service Temperature: minus 300F to 1200F [minus 185C to 650C]

Surface Application Temperatures: 50F to 600F [10C to 316C]*

Hi-Temp 1027 is a high-build, single component coating formulated to prevent corrosion under insulation ofcarbon and stainless steel.

Hi-Temp 1027 is formulated to help prevent chloride induced stress corrosion cracking of stainless steel andhas been tested by an independent laboratory for low leachable chlorides, sulfides and halides. It helps protectagainst chlorides: 1) from the atmosphere, 2) from by-products of process operations, and 3) which may beincorporated in the insulation, from coming in contact with stainless steel.

Hi-Temp 1027 is a low VOC, high build primer which air dries at ambient temperatures to a UV resistant andstable film, and provides excellent corrosion resistance at the full range of service temperatures.

Hi-Temp 1027 can be top coated with a full range of Hi-Temp color top coats.

Hi-Temp 1027 can be applied directly to hot substrates having a metal temperature up to 600F [316C]*,

eliminating the need for costly shutdown during maintenance. Hi-Temp 1027 does not require a heat cure to achieve superior corrosion resistance. Hi-Temp 1027 is resistant to thermal shock and thermal cycling in intermittent (wet, steam, dry) service. Hi-Temp 1027 can be applied to tightly adhering rust in maintenance and repair situations. Hi-Temp 1027 will protect cryogenic equipment in continuous or cyclic operation from minus 300F to 1000F

[minus 185C to 538C]. Hi-Temp 1027 provides a UV-resistant, chalking-free film with no maximum recoat interval, regardless of

operating temperature, as long as the surface to be recoated is clean and free of all contaminants.

TECHNICAL DATA:

Components: One

Type: Inert Multipolymeric Matrix

Dry Temperature Resistance: 1200

F [650

C] Continuous, 1400

F [760

C] PeakCryogenic Service: Minus 300F to 1000F [Minus 185C to 538C]

Adhesion ASTM 3359-09: 4A to 5A

Impact ASTM G-14 (direct): 30 lbs.

Colors Available: Black (Dark Gray), Gray, and Light Gray

Minor color change may occur in exposed service, but corrosion protection will not be compromised.

Finish: Flat

Dry Time @ 50% R.H., 70F [21C]:(Recoat and dry times are reduced whenapplied to hot substrates)

To touch 2 hoursTo ship 24 hoursTo topcoat 6 hours

Substrate Temperature During Application: 50F [10C] and rising to 600F [316C]*Thinner/Cleanup: See Mixing, Thinning, and Cleanup Table

Volume Solids: 65% 2% as applied

Coverage @ 1 mil DFT@ 25 microns DFT

1042 ft /gal[25.5 m

2/l]

VOC: 3.5 lbs/gal [420 g/l]

Weight: 16 lbs/gallon [1.92 kg/liter]

Packaging: 1 gallon cans; 50 gallon drums

Storage Temperatures: 40F to 120F [4C to 49C]

Shelf Life: Two years

*For direct application to hot substrates over 500F and up to 600F [260C to 316C]consult Hi-Temp Technical Service.


13/1103

Product: Hi-Temp 1027 Page 2 of 4Rev. 090412

SURFACE PREPARATION:

As wi th all coatings, the performance and service l ife of Hi -Temp 1027 are relative to the qual ity o f sur facepreparation accomplished.

CARBON STEEL All surfaces to be coated with Hi-Temp 1027 shall be free of all weld splatter, oil, dirt, grease,and all other contaminants, especially salts. Round off all rough welds and sharp edges.

In maintenance and repair situations, Hi-Temp 1027 can be applied over a surface in which tightly adhering rust isstill present;remove all rust scale and loosely adhering rust until glints of bright metal are visible. The remainingrust must be tightly adherent and not easily removed by lightly wiping with a cloth.

Hi-Temp 1027 should only be used to overcoat inorganic zinc or itself. When overcoating aged inorganic zinc,prepare a small test patch and check for adhesion. If previously applied coatings other than inorganic zinc or Hi-Temp 1027 are not fully removed by the method of surface preparation utilized, feather the edges of any remainingold coating, and use Hi-Temp 1027 to spot prime only the areas where the substrate is exposed.

Non-insulated surfaces:

Recommended: Dry abrasive blast clean to SSPC-SP 6, Commercial Blast [Sa 2] with a 1.0 to 2.0 mil [25to 50 micron] profile.

When abrasive blast cleaning is not an option, the following methods are acceptable:

SSPC-SP 15 Commercial Grade Power Tool Cleaning, with a minimum 1.0 mil [25 micron] profile.

SSPC-SP 12, Surface Preparation and Cleaning of Metals by Waterjetting Prior to Recoating to meet thevisual definition of WJ-3, Thorough Cleaning. Use potable water.

SSPC-SP 3, Power Tool Cleaning [St 3] or SSPC-SP 2, Hand Tool Cleaning [St 2].

Insulated surfaces:

Recommended: Dry abrasive blast clean to SSPC-SP 6, Commercial Blast [Sa 2] or better, with a 1.0 to2.0 mil [25 to 50 micron] profile.

When abrasive blasting is not an option, the following methods are acceptable:

SSPC-SP 15 Commercial Grade Power Tool Cleaning, with a minimum 1.0 mil [25 micron] profile.

SSPC-SP 12, Surface Preparation and Cleaning of Metals by Waterjetting Prior to Recoating to meet thevisual definition of WJ-2 Very thorough or Substantial Cleaning. Use potable water. All existing coatingmust be removed except for aged inorganic zinc or existing Hi-Temp 1027.

Power Tool Clean or Hand Tool Clean to remove all existing coating except for aged inorganic zinc orexisting Hi-Temp 1027.

STAINLESS STEEL All surfaces to be coated with Hi-Temp 1027 shall be free of all weld splatter, oil, dirt,grease, and all other contaminants, especially salts. Round off all rough welds and sharp edges.

IMPORTANT: DO NOT USE CHLORINATED SOLVENTS ON STAINLESS STEEL SURFACES.

Non-insulated and insulated sur faces:

Small surfaces may be cleaned with a chloride free solvent. Large surfaces may be cleaned utilizing ahigh or low pressure wash or steam cleaning with an alkaline detergent, followed by a freshwater rinse.Water used should be potable grade or better and should be checked to assure minimal salt content. Donot use any chemical additives in the rinse water.

An anchor profile is not mandatory for adhesion of Hi-Temp 1027 on stainless steel surfaces.o As an option, following cleaning, a light abrasive sweep blast using an appropriate chloride free

abrasive may be performed. After completion of this mechanical surface preparation, rinse the surfacewith potable grade water or better. Always allow rinsed surfaces to dry before coating.


14/1103


MIXING, THINNING, AND CLEANUP:

Hi-Temp 1027 is a heavy bodied material; use mechanical agitation for mixing immediately before application andas needed during application. Be sure any settled solids are incorporated during mixing. If thinning is needed, thinonly with Hi-Temp thinners and in accordance with applicable regulations. Agitate as needed during application.

Application to ambient substrateBelow 150F [66C]

Application to hot substrate 150F to 500F[66C to 260C]

Flush equipment and thin with Hi-Temp #10 or #11 Flush equipment and thin with Hi-Temp #5

Clean up with Thinners #5, #10, #11

For application to hot substrates over 150F and up to 500F [66C to 260C] thin (if needed) only with Hi-Temp thinner #5. For application to subst rates over 500F and up to 600F [260C to 316C] consultHi-Temp Technical Service.

APPLICATION:

For ambient application, surface temperature should be a minimum of 5F [3C] above the dew point. Do not applyto surfaces with surface temperature below 50F [10C]. Do not exceed recommended maximum dry filmthicknesses for the appropriate service type and temperatures.

APPLICATION TO HOT SURFACES:

IMPORTANT! It is essential to apply multiple thin passes of Hi-Temp 1027 during application to hot steel. Thisprocess, similar to mist coating, prevents blistering and also allows solvent to escape without leaving pinholes. Useof a solvent other than Hi-Temp #5 thinner could produce a fire hazard, and dry spray and poor filmcharacteristics may also result. If blisters are observed in Hi-Temp 1027 applied to hot surfaces, immediately brushout the blisters before they set, using a wood-handled china bristle brush. Note that the higher the substratetemperature, the shorter the recoat time.

For direct application to hot substrates over 500F and up to 600F [260C to 316C] consult Hi-Temp

Technical Service.

APPLICATION EQUIPMENT:

Spray application is recommended: Use conventional or airless spray and good painting practices. Typicalequipment is as follows:

Product Conventional Spray Airless Spray

AirPressure

FluidPressure

Fluid Tip Pressure Minimum FluidLine

Tip size

1027 60-80 psi


15/1103


II. PRIMER / TOPCOAT SYSTEM NON-INSULATED SERVICECarbon Steel / Stainless Steel Applied direct to hot or ambient steel

Primer Coat - Hi-Temp 1027 - 1 coat @ 5 to 6 mils DFT [125 to 150 microns]

Hi-Temp Color Topcoats (See appropriate topcoat PDS)a] Ambient apply: Hi-Temp 500VS or Hi-Temp 1000VS

b] Hot apply: Hi-Temp 500VHA or Hi-Temp 1000VHA

III. CRYOGENIC INSULATED AND NON-INSULATED SERVICEAmbientStainless Steel

Hi-Temp 1027[1.] For service temperature of minus 100 F to 400 F [minus 73C to 204C]

2 coats @ 5 to 6 mils [125 to 150 microns] DFT per coat; total of 10 to12 mils [250 to 300 microns]

[2.] For service temperature of minus 300 F to 1000 F [minus 185 C to 538C]1 coat @ 5 to 6 mils [125 to 150 microns] - DO NOT EXCEED 8 mils [200 microns] total DFT

RECOMMENDED APPLICATION PER COAT:

Minimum MaximumMils Microns Mils Microns

Dry Film Thickness 5 [125] 6 [150]

Wet Film Thickness 7.7 [192] 9.2 [230]

Coverage 208 ft2/gal [5.1 m

2/l] 174 ft

2/gal [4.3 m

2/l]

APPROXIMATE DRY SCHEDULE:

Substrate Temperature at50% RH 50F [10C] 70F [21C] 100F [38C] 302F [150C]

Dry to Recoat, Minimum 24 hours 6 hours 5 hours 1/4 hour

Dry to Recoat, Maximum No maximum as long as the surface is clean and free of contaminants

Dry to Ship 24 hours 24 hours 24 hours N/ACured N/A N/A N/A N/A

Dry times can vary based on environmental and substrate conditions.Do not exceed maximum dry film thickness recommendations as this can affect dry times.

PRECAUTIONS:

This product is for use only by professional applicators in accordance with information in this data sheet and theapplicable material safety data sheets (MSDS). Refer to the appropriate MSDS before using this material. All useand application of this product should be performed in compliance with all relative federal, state and local health,safety and environmental regulations or in compliance with all pertinent local, regional and national regulations aswell as good safety practices for painting, and in conformance with recommendations in SSPC-PA 1, Shop, Fieldand Maintenance Painting of Steel.

WARRANTY:

Hi-Temp Coatings Technology, Inc. (Hi-Temp) warrants that its products are free from defects in material andworkmanship. Hi-Temps sole obligation and buyers exclusive remedy shall be limited to replacement of productsnot conforming to this warranty. Any claim for replacement product must be made within one year from the deliverydate. Hi-Temp makes no other warranties, expressed or implied, such as warranties of merchantability or fitness fora particular purpose. Hi-Temp products are intended for buyers with the knowledge and skills to evaluate thesuitability of Hi-Temps products for buyers intended use. In no event shall Hi-Temp be liable for consequential orincidental damage.


16/1103

HI-TEMP COATINGS TECHNOLOGY P.O. Box 2347 Acton, MA 01720Tel: 978-635-1110 Fax: 978-635-1124 hitemp@hitempcoatings .com www.hitempcoatings.com

Rev. 082012 Page 1 of 3

HI-TEMP 1000VS Heat Resistant Standard and Custom Color Topcoats Superior Color Stability to 1000F [538C] Ambient Temperature Cure & VOC < 3.5 lb/gal

PRODUCT DESCRIPTION:For use as a topcoat fo r Hi-Temp 1027

Hi-Temp 1000VS is formulated with a highly engineered silicone resin, enabling it to withstand severethermal cycling to 1200F [649C]. This also allows Hi-Temp 1000VS to have superior color stability ascompared to most generic silicone topcoats, which tend to discolor at elevated temperatures.

Hi-Temp 1000VS is available in both standard and custom colors. Hi-Temp 1000VS air dries rapidly and does not require heat cure. Hi-Temp 1000VS has excellent spray application properties. Hi-Temp 1000VS is a user-friendly system that can be brushed and rolled. Hi-Temp 1000VS has excellent weathering and corrosion resistance when applied over properly primed

surfaces.

Hi-Temp 1000VS does not soften in thermal cyclic service. Color stability may be affected at the top end of the temperature range. Hi-Temp 1000VS is specifically formulated as an ambient, heat resistant topcoat for Hi-Temp 1027.TECHNICAL DATA:

Type: Silicone

Dry Temperature Resistance: To 1200F [650C]

Color Stability: Standard & Custom To 1000F [538C]

Black To 1200F [650C]

Colors: Standard & Custom

Finish: Flat

Components: One

Dry Time @ 50% R.H., 70F [21C]

- To touch Two Hours

- To ship 24 Hours

Cure: N/A

Metal Temperature During Application: 50F to 150F [10C to 66C]

Thinner: Hi-Temp #10 or #11

Volume Solids: 34%

Theoretical Coverage @1 mil DFT 545 ft2/gal

Theoretical Coverage @25 microns 13.4 m2/l

VOC Content: 3.5 lb/gal [420 g/l]

Weight per Gallon: 11.4 lb. [5.2 kg]

Storage Temperature: 40F to 120F [4C to 49C]

Shelf Life:

One year

SURFACE PREPARATION: Performance of the coating system is relative to the surface preparation accomplished.

Hi-Temp 1000VS is designed to be applied over Hi-Temp 1027 primer.


17/1103

Product: Hi-Temp 1000VS Page 2 of 3Rev. 082012

New or Corroded Surfaces:

For corrosion resistant service, use of an approved corrosion resistant primer is necessary. Surfacesto be coated must be primed in accordance with the Hi-Temp 1027 product data sheet. Consult Hi-Temp for alternate and approved primers. Allow appropriate dry time. Apply one coat of Hi-Temp1000VS at 2 to 2.5 mils [50 to 63 microns] DFT.

For cosmetic service only, use of an approved corrosion resistant primer is recommended but notnecessary. Abrasive blast clean to SSPC-SP 6 Commercial Blast [Sa 2] with profile of 1 to 1.5

mils [25 to 38 microns] or pressure wash to an equivalent of SSPC-SP 6 [Sa 2] condition.Surfaces to be coated must be dry and free of salts, weld splatter, oil, dirt, grease, and all othercontaminants. Round off all rough welds and sharp edges. Apply two coats of Hi-Temp 1000VS at 2to 2.5 mils [50 to 63 microns] DFT per coat for a total of 4 to 5 mils [100 to 125 microns] DFT.

Previously Painted Surfaces in Good Condition : If old coating is intact and there is no evidence of cracking, fracturing, and/or delamination, pressure

wash surface to remove all salts, oil, grease, and contaminants and apply one coat of Hi-Temp1000VS at 2 to 2.5 mils [50 to 63 microns] DFT.

Previously Painted Surfaces in Poor Condition or w ith some Localized Corrosion :If old coating shows evidence of cracking, fracturing, delamination, and/or corrosion, follow surfacepreparation guidelines for new steel. If there is no evidence of cracking, fracturing, or delamination, justsmall areas of corrosion (less than 10% of the area to be coated), power wash the entire structure,

removing all salts, oil, grease, and other contaminants. Once dry, perform surface preparation and applyHi-Temp 1027 in accordance with the data sheet on all areas where the existing paint has been removed.Once these areas are primed and dry, apply one coat of Hi-Temp 1000VS at 2 to 2.5 mils [50 to 63microns] DFT over the entire surface.

Prior to application of 1000VS over other coatings, prepare a small test patch area andtest for adhesion.

MIXING, THINNING, AND CLEANUP:

Use mechanical agitation for mixing. Mix materials until uniform in consistency. Thinning is not normallyneeded. If a condition warrants thinning, thin only with Hi-Temp Thinners #10 or #11. Thin only inaccordance with applicable regulations.

Appl ication to Ambient Substrate 50F [10C] to 150F [66C]

Flush, Thin, and Clean up with: Hi-Temp Thinner #10 or #11

APPLICATION:

Surface temperature must be a minimum of 5F [3C] above the dew point. Do not apply at substratetemperatures below 50F [10C] or above 150F [66C].

APPLICATION EQUIPMENT:

Spray: Standard conventional or airless spray is highly recommended. Use good painting practices.Typical equipment is as follows:

Product Conventional Spray Airless Spray

AirPressure

FluidPressure

Fluid Tip Pressure Minimum FluidLine

Tip size

1000VS 60-80 psi


18/1103

Product: Hi-Temp 1000VS Page 3 of 3Rev. 082012

APPLICATION SYSTEMS:

Un-insulated steel Do not exceed recommended dry film thickness

Primer Hi-Temp 1027 5.0 to 6.0 mils [125 to 150 microns] DFT

Topcoat Hi-Temp 1000VS 2.0 to 2.5 mils [50 to 63 microns] DFT

Total Dry Film Thickness 7.0 to 8.5 mils [175 to 213 microns] DFT

RECOMMENDED APPLICATION PER COAT:

Hi-Temp 1000VS

Minimum Maximum

Mils Microns Mils Microns

Dr Film 2 [50] 2.5 [63]

Wet Film 5.9 [148] 7.3 [183]

Theoretical Coverage 273 ft2/gal [6.7 m2/l ] 218 ft

2/gal. [5.4 m

2/l]

DRY SCHEDULE:

Substrate Temperatureat 50% RH

50F [10C] 70F [21C] 90F [32C] 150F [66C]

Dry to touch 4 hours 2 hours 2 hours hour

Dry to Ship 72 hours 24 hours 16 hours hour

Cure N/A

When shipping and handling equipment coated w ith Hi-Temp 1000VS follow procedures for thin film coatings.

Avo id mechan ical damage and abrasion .

PRECAUTIONS:

This product is for use only by professional applicators in accordance with information in this data sheetand the applicable material safety data sheets (MSDS). Refer to the appropriate MSDS before using thismaterial. All use and application of this product should be performed in compliance with all relative federal,state and local health, safety and environmental regulations or in compliance with all pertinentlocal, regional and national regulations as well as good safety practices for painting, and inconformance with recommendations in SSPC PA 1, Shop, Field and Maintenance Painting of Steel.

WARRANTY:

Hi-Temp Coatings Technology, Inc. (Hi-Temp) warrants that its products are free from defects in materialand workmanship. Hi-Temps sole obligation and buyers exclusive remedy shall be limited to replacementof products not conforming to this warranty. Any claim for replacement product must be made within

one year from the delivery date. Hi-Temp makes no other warranties, expressed or implied, such aswarranties of merchantability or fitness for a particular purpose. Hi-Temp products are intended forbuyers with the knowledge and skills to evaluate the suitability of Hi-Temps products for buyers intendeduse. In no event shall Hi-Temp be liable for consequential or incidental damage.


19/1103


20/1103

page 1/3

April 20093 pagesRevision of November 2005

two component solvent free amine cured phenolic epoxy compound

sprayable caulking to overlap the welding seamssuitable caulking compound for use under SigmaGuard CSF 650 and

Novaguard 840excellent chemical resistance against crude oil, unleaded gasolines and a

wide range of petrochemicals and solvents

can be applied by heavy duty single feed airless spray equipment (60:1)good visibility due to light colour

reduced explosion risk and fire hazard

cream - gloss

(1 g/cm = 8.25 lb/US gal; 1 m/l = 40.7 ft/US gal)(data for mixed product)

1.4 g/cm

100%max. 105 g/kg (Directive 1999/13/EC, SED)

max. 144 g/l (approx. 1.2 lb/gal)3500 - 5000 m depending on system

6 hoursmin. 16 hours *

max. 3 months *5 days *

(data for components)

at least 12 months

steel; blast cleaned to a minimum of ISO-Sa2, blasting profile 50 - 100 m

steel with suitable holding primer (SigmaGuard 260 or SigmaCover 280)which must be dry, clean and free from any contamination

mixing ratio by volume: base to hardener 75 : 25

when mixing the temperature of the base and hardener should be at least

20Cat lower temperature the viscosity will be too high for spray application

no thinner should be added

none

1 hour at 20C *

* see additional data

DESCRIPTION


COLOURS AND GLOSS

BASIC DATA AT 20C

Mass density

Volume solidsVOC (supplied)

Recommended dry film thickness


Full cure after


RECOMMENDED



Induction time

Pot life

NOVAGUARD 830


21/1103

page 2/3

April 2009

NOVAGUARD 830

heavy duty single feed airless spray equipment with a minimum of 60:1pump ratio and suitable high pressure hoses

in-line heating or insulated hoses may be necessary to avoid cooling downof paint in hoses at low air temperature

length of hoses should be as short as possibleno thinner should be added

approx. 0.67 mm (= 0.026 in) at an angle of 30 40

at 20C (paint temperature) min. 30 MPa (= approx. 350 bar; 5000 p.s.i.)at 30C (paint temperature) min. 25 MPa (= approx. 250 bar; 3500 p.s.i.)

Thinner 90-83

all application equipment must be cleaned immediately after usepaint inside the spraying equipment must be removed before the pot life time

has been expired

for paint and recommended thinners see safety sheets 1430, 1431 and relevantmaterial safety data sheets

Film thickness and spreading rate

theoretical spreading rate m/l 0.3

dft in m 3000

structure: in different layers wet in wet in order to reach the required filmthickness

Overcoating table with solvent free tanklinings

substrate temperature 10C 20C 30C

minimum interval 30 hours 16 hours 12 hours

maximum interval 3 months 2 months 1 month

surface should be dry and free from any contamination

Curing table

substrate temperature dry to handle full cure

10C 30 hours 7 days

20C 16 hours 5 days

30C 10 hours 3 days

although the paint is solvent free adequate ventilation must be maintainedduring application and curing (please refer to sheet 1433 and 1434)

AIRLESS SPRAY

Recommended thinner

Nozzle orifice

Nozzle pressure

CLEANING SOLVENT

SAFETY PRECAUTIONS

ADDITIONAL DATA


22/1103

page 3/3

April 2009

NOVAGUARD 830

Pot life

20C 60 min.

30C 45 min.

due to exothermic reaction, temperature during and after mixing may

increase

Whilst it is always the aim of PPG Protective & Marine Coatings to supplythe same product on a worldwide basis, slight modification of the product is

sometimes necessary to comply with local or national rules/circumstances.

Under these circumstances an alternative product data sheet is used.



Safe working in confined spaces see information sheet 1433Directives for ventilation practice see information sheet 1434

Cleaning of steel and removal of rust see information sheet 1490

LIMITATION OF LIABILITY

The information in this data sheet is based upon laboratory tests we believe to be accurate and is intended for

guidance only. All recommendations or suggestions relating to t he use of the Sigma Coatings products made by PPG

Protective & Marine Coatings, whether in technical documentation, or in response to a specific enquiry, or otherwise,

are based on data which to the best of our knowledge are reliable. The products and information are designed for

users having the requisite knowledge and industrial skil ls and it is the end-user's responsibility to determine the

suitability of the product for its int ended use.

PPG Protective & Marine Coatings has no control over either the quality or condition of the substrate, or the many

factors affecting the use and application of the product. PPG Protective & Marine Coatings does therefore not accept

any liability arising from loss, injury or damage resulting from such use or the contents of thi s data sheet (unless there

are written agreements stating otherwise).

The data contained herein are liable to modification as a result of practical experience and continuous productdevelopment.

This data sheet replaces and annuls all previous issues and it is therefore the user's responsibility to ensure that this

sheet is current prior to using the product.

The English t ext of this document shall prevail over any translation thereof.

PDS 7945


REFERENCES


23/1103


24/1103

February 2013

page 1/5

5 pages

Revision of March 2011

NOVAGUARD 840

two component solvent free amine cured novolac phenolic epoxy coating

one coat tank coating system

clear version for glassmat reinforced solvent free tank bottom system (seesystem sheet 4145)

excellent resistance to crude oil up to 90C suitable for storage of unleaded gasolines

good chemical resistance against a wide range of chemicals and solvents good visibility due to light colour

glossy and smooth appearance easy to clean

can be applied by heavy duty single feed airless spray equipment (60:1)

reduced explosion risk and fire hazard approved to Air BP F2D2 section 2.1 for the storage of jet fuels

green, cream, clear gloss

(1 g/cm = 8.35 lb/US gal; 1 m/l = 40.7 ft/US gal)

(data for mixed product)

1.3 g/cm100%

max. 106 g/kgmax. 142 g/l (approx. 1.2 lb/gal)

73 g/ltr (0.6 lb/gal) (by EPA Method 24) see information sheet 1411Recommended dry film thickness 300 - 600 m depending on system

Theoretical spreading rate 3.3 m/l for 300 m *

6 hours at 20Cmin. 24 hours *

max. 2 months *5 days * at 20C


at least 12 months* see additional data

steel; blast cleaned to a minimum of ISO-Sa2, blasting profile 50 - 100 m substrate temperature must be above 5C and at least 3C above dew point

during application and curing steel with suitable primer (SigmaGuard 260) which must be dry, clean and

free from any contamination

Description


COLOURS AND GLOSS

BASIC DATA AT 20C


VOC (Supplied)

VOC (EPA Method 24)


Full cure after


RECOMMENDEDSUBSTRATE CONDITIONS

AND TEMPERATURES


25/1103

February 2013

page 2/5

NOVAGUARD 840


the temperature of the mixed base and hardener should preferably be atleast 20C

at lower temperature the viscosity will be too high for spray application no thinner should be added

for recommended application instructions: see working procedurenone

1 hours at 20C **see additional data

use heavy duty single feed airless spray equipment preferably 60:1 pump ratioand suitable high pressure hoses/in -line heating or insulated hoses may be

necessary to avoid cooling down of paint in hoses at low air temperaturelength of hoses should be as short as possible

Recommended thinner no thinner should be added

Nozzle orifice approx. 0.53 mm (= 0.021 in)

Nozzle pressure at 20C (paint temperature) min. 28 MPa (= approx. 280 bar; 4061 p.s.i.)at 30C (paint temperature) min. 22Mpa (=approx. 220 bar: 3000 p.s.i.)

only for spot repair and stripe coating


Thinner 90-83 (preferred) or Thinner 90-53

paint inside the spraying equipment must be removed before the pot life timehas been expired

all equipment used for application must be cleaned immediately after use


theoretical spreading rate m/l 3.3 1.7

dft in m 300 600

Maximum dft when brushing: 150 m

measuring wet film thickness a deviation is often obtained between the measured apparent wft and the

real applied wft this is due to the thixotropy and the surface tension of the paint which

retards the release of air trapped in the paint film for some time recommendation is to apply a wft which is equal to the specified dft

plus 60 m


Induction time

Pot life

AIRLESS SPRAY

BRUSH/ROLLER

CLEANING SOLVENT


26/1103

February 2013

page 3/5

NOVAGUARD 840

measuring d ry film thickness

because of low initial hardness the dft cannot be measured within somedays due to the penetration of the measuring device into the soft paint film

the dft should be measured using a calibration foil of known thickness placedin between the coating and the measuring device

Overcoating with Novaguard 840 (spot repair and stripe coating)

substrate temperature 5C 10C 20C 30C

minimum interval 80 hours 36 hours 24 hours 16 hours

maximum interval 3 months 3 months 2 months 1 month


Curing table


5C 60 hours 15 days

10C 30 hours 7 days

20C 16 hours 5 days

30C 10 hours 3 days

adequate ventilation must be maintained during application and curing

(please refer to sheets 1433 and 1434)

for storage and transport of drinking water the recommended workingprocedure should be followed

WASHING PROCEDURE

all personnel should wear watertight suits, boots and gloves properlycleaned with a sodium hypochlorite solution (1% active chlorine per liter)

all tank sides, bottom and deckheads etc. should be brush cleaned or high-pressure spray cleaned with 1% active chlorine solution as above

note: this can also be done by butterworth washing all parts should be high pressure cleaned with tap water and tanks drained

concentrated active chlorine solution should be sprinkled on bottom;approx. 1 ltr/10 m

tanks should be filled with tap water to a depth of approx. 20 cm and thewater should remain in the tank for at least 2 hours (max. 24 hours)

tanks should be thoroughly flushed out with tap water

depending upon local regulations it may be necessary to take watersamples, after filling tank completely, to check on bacteria

after this procedure the tanks will be fit to carry drinking water

Curing


27/1103

February 2013

page 4/5

NOVAGUARD 840

Pot life (at application viscos ity)

20C 60 min.

30C 45 min.

due to exothermic reaction, temperature during and after mixing mayincrease




Safety indications see information sheet 1430Safe working in confined spaces see information sheet 1433

Cleaning of steel and removal of rust see information sheet 1490Explanation to product data sheets see information sheet 1411


Directives for ventilation practice see information sheet 1434

Specification for mineral abrasives see information sheet 1491Safety in confined spaces and health safety

Explosion hazard - toxic hazard see information sheet 1431Relative humidity - substrate temperature -

air temperature see information sheet 1650Conversion tables see information sheet 1410

for paint and recommended thinners see safety sheets 1430, 1431 and

relevant material safety data sheets although this is a solvent free paint, care should be taken to avoid inhalation

of spray mist as well as contact between the wet paint and exposed skin oreyes

no solvent present; however, spray mist is not harmless, a fresh air mask

should be used during spraying

ventilation should be provided in confined spaces to maintain goodvisibility


REFERENCES

SAFETY PRECAUTIONS


28/1103

February 2013

page 5/5

NOVAGUARD 840

WARRANTY




























PDS 7468

237775 cream 3012002200

180207 green 4000001400


29/1103


30/1103

September 2013

page 1/5

5 pages

Revision of November 2012

NOVAGUARD 890

two component solvent free amine cured novolac phenolic epoxy coating

one coat tank coating system

excellent resistance to crude oil up to 90C suitable for storage of unleaded gasolines blended up to 100% ethanol

(E5 up to E100) suitable for storage of biodiesel (EN14214)

good chemical resistance against a wide range of chemicals and solvents good visibility due to light colour

semigloss and smooth appearance clear version for glassmat reinforced solvent free tank bottom system (see

system sheet 4155)

easy to clean can be applied by heavy duty single feed airless spray equipment (60:1)

reduced explosion risk and fire hazard

green, cream, clear semi-gloss



1.4 g/cm

100%max. 94 g/kg (Directive 1999/13/EC, SED)

max. 131 g/l (approx. 1.1 lb/gal)see information sheet 1411

Recommended dry film thickness 300 - 600 m depending on system

Theoretical spreading rate 3.3 m/l for 300 m *8 hours at 20C

min. 24 hours *max. 2 months *6 days *



steel; blast cleaned to a minimum of ISO-Sa2, blasting profile 50 - 100 m substrate temperature should be above 5C and at least 3C above dew

point during application and curing steel with suitable primer (SigmaGuard 260) which must be dry, clean and

free from any contamination

Description


COLOURS AND GLOSS

BASIC DATA AT 20C

Mass density

Volume solidsVOC (Supplied)

Touch dry after

Overcoating interval

Full cure after



AND TEMPERATURES


31/1103

September 2013

page 2/5

NOVAGUARD 890


the temperature of the mixed base and hardener should preferably be at

least 20C no thinner should be added

for recommended application instructions: see working procedure at lower temperature the viscosity will be too high for spray application

none1 hour at 20C *



Nozzle orifice approx. 0.53 mm (=0.021 in)

Nozzle pressure at 20C (paint temperature) min. 28 MPa (= approx. 280 bar; 4061 p.s.i.)at 30C (paint temperature) min. 22Mpa (=approx. 220 bar: 3000 p.s.i.)

use heavy duty single feed airless spray equipment preferably 60:1 pumpratio and suitable high pressure hoses

for stripe coating and spot repair onlyRecommended thinner no thinner should be added

Thinner 90-83 (preferred) or Thinner 90-53

all application equipment must be cleaned immediately after use paint inside the spraying equipment must be removed before the pot life time

has been expired


theoretical spreading rate m/l 3.3 1.7

dft in m 300 600


measuring wet film thickness a deviation is often obtained between the measured apparent wft and the

real applied wft

this is due to the thixotropy and the surface tension of the paint whichretards the release of air trapped in the paint film for some time

recommendation is to apply a wft which is equal to the specified dftplus 60 m


Induction timePot life

AIRLESS SPRAY

BRUSH/ROLLER

CLEANING SOLVENT

ADDITIONAL DATA


32/1103

September 2013

page 3/5

NOVAGUARD 890

measuring d ry film thickness

because of low initial hardness the dft cannot be measured within somedays due to the penetration of the measuring device into the soft paint film

the dft should be measured using a calibration foil of known thickness placedin between the coating and the measuring device

Overcoating table with itself (spot repair and s tripe coating)

substrate temperature 10C 20C 30C

minimum interval 36 hours 24 hours 16 hours

maximum interval 3 months 2 months 1 month


Curing table


10C 40 hours 10 days

20C 18 hours 6 days

30C 12 hours 4 days

adequate ventilation must be maintained during application and curing(please refer to sheets 1433 and 1434)

for storage and transport of drinking water the recommended working

procedure should be followed


20C 60 min.

30C 45 min.

due to exothermic reaction, temperature during and after mixing may

increase

It is always the aim of PPG Protective and Marine Coatings to supply the sameproduct on a worldwide basis. However, slight modification of the product is

sometimes necessary to comply with local or national rules/circumstances.Under these circumstances an alternative product data sheet is used

Curing



33/1103

September 2013

page 4/5

NOVAGUARD 890

Conversion tables see information sheet 1410




Cleaning of steel and removal of rust see information sheet 1490Specification for mineral abrasives see information sheet 1491

Relative humidity - substrate temperature -air temperature see information sheet 1650


although this is a solvent free paint, care should be taken to avoid inhalationof spray mist as well as contact between the wet paint and exposed skin or

eyes no solvent present; however, spray mist is not harmless, a fresh air mask

should be used during spraying ventilation should be provided in confined spaces to maintain good

visibility

REFERENCES

SAFETY PRECAUTIONS


34/1103

September 2013

page 5/5

NOVAGUARD 890

WARRANTY




























PDS 7755

269264 green 4194542200

282887 cream 3002002200


35/1103


36/1103

November 2012

page 1/4

4 pages

Revision of September 2011

Phenguard 253

two component high build amine adduct cured novolac phenolic epoxy primer

excellent resistance to a wide range of organic acids, alcohols, edible oils

and solvents maximum cargo flexibility

low cargo absorbtion recognized corrosion control coating (Lloyds register) See sheet 1886

good application properties, resulting in a smooth surface

grey, offwhite semigloss



1.4 g/cm ( mixed product )72% 3%

max. 200 g/l (approx. 1.7 lb/gal)(UK PG 6/23(92) Appendix 3)

Recommended dry film thickness 125 - 150 m

Theoretical spreading rate 7.2 m/l for 100 mmin.10 hours*

max. 5 days *at least 12 months


steel; blast cleaned in situ to at least ISO-Sa2 and free from rust, scale,

shop primer and any other contamination blasting profile 50 - 100 m

the substrate must be perfectly dry before and during application ofPhenguard 253

substrate temperature must be above 10C and at least 3C above dewpoint during application and curing


the temperature of the paint should preferably be above 15C, otherwise

extra thinner may be required to obtain application viscosity

too much solvent results in reduced sag resistance and slower cure thinner should be added after mixing the components

allow induction time before use15C - 45 min.

20C - 30 min.25C - 15 min.

4 hours at 21.1C / 70F


Description


COLOURS AND GLOSS

BASIC DATA AT 20 C


VOC (UK PG 6/23(92) appendix 3)



RECOMMENDED



Induction time

Pot life


37/1103

November 2012

page 2/4

Phenguard 253


Volume of thinner 5 - 10%, depending on required thickness and application conditions

Nozzle orifice 2 mm

Nozzle pressure 0.3 MPa (= approx. 3 bar; 44 p.s.i.)





only for touch up and spot repairRecommended thinner Thinner 91-92


Thinner 90-53


theoritical spreading rate m2/l 7.2 4.8

dft in m 100 150

Overcoating tabel for Phenguard 253

substratetemperature

10C 15C 20C 30C 40C

minimum interval 24 hours 16 hours 10 hours 4 hours 3 hours

maximum interval 7 days 6 days 5 days 4 days 3 days


Curing table

substrate temperature Service

10C 14 day

15C 10 days

20C 7 days

30C 4 days

40C 4 days

minimum curing time of Phenguard 253 tank coating systems before the transport of

cargoes

please contact your PPG representative for further details

AIR SPRAY

AIRLESS SPRAY

BRUSH/ROLLER

CLEANING SOLVENT

ADDITIONAL DATA

Curing


38/1103

November 2012

page 3/4

Phenguard 253


10C 6 hours

20 C 4 hours

30 C 2 hours

Whilst it is always the aim of Sigma Coatings to supply the same product on a

worldwide basis, slight modification of the product is sometimes necessary tocomply with local or national rules/circumstances.


Explanation to product data sheets see information sheet 1411

Safety indications see information sheet 1430Safety in confined spaces and health safety

Explosion hazard - toxic hazard see information sheet 1431Safe working in confined spaces see information sheet 1433

Directives for ventilation practice see information sheet 1434Cleaning of steel and removal of rust see information sheet 1490

Specification for mineral abrasives see information sheet 1491


This is a solvent borne paint and care should be taken to avoid inhalationof spray mist or vapour as well as contact between the wet paint and

exposed skin or eyes


REFERENCES

SAFETY PRECAUTIONS


39/1103

November 2012

page 4/4

Phenguard 253



















PDS 7447


40/1103

July 2012

page 1/5

5 pages


PHENGUARD 930

two component high build amine adduct cured novolac phenolic epoxy primer

primer coat in the Phenguard tankcoating system

excellent resistance to a wide range of organic acids, alcohols, edible oils,fats (regardless of free fatty acid content) and solvents

maximum cargo flexibility low cargo absorption

good resistance to hot water recognized corrosion control coating (Lloyd's register), see sheet 1886


offwhite eggshell



1.7 g/cm66% 2%

max. 191 g/kg (Directive 1999/13/EC, SED)max. 315 g/l (approx. 2.6 lb/gal)

(UK PG 6/23(92) Appendix 3)Recommended dry film thickness 100 m *

Theoretical spreading rate 6.6 m/l for 100 m *2 hours at 20 C

min. 36 hours *

max. 21 days *

see curing table *at least 12 months* see additional data

steel; blast cleaned in situ to at least ISO-Sa2 and free from rust, scale,shop primer and any other contamination

blasting profile 50 - 100 m the substrate must be perfectly dry before and during application of

Phenguard 930 substrate temperature must be above 10C and at least 3C above dew

point during application and curing

marine system sheet: 3141

tankcoatings system sheet: 3322

Description


COLOURS AND GLOSS

BASIC DATA AT 20 C


VOC (Directive 1999/13/EC, SED)VOC (UK PG 6/23(92) appendix 3)

Touch dry after


Full cure afterShelf life (cool and dry place)


AND TEMPERATURES

SYSTEM SPECIFICATION


41/1103

July 2012

page 2/5

PHENGUARD 930


the temperature of the mixed base and hardener should preferably be

above 15C, otherwise extra solvent may be required to obtain applicationviscosity


4 hours at 20 C * allow induction time before use

15C - 20 min. 20C - 15 min.

25C - 10 min.



Nozzle orifice 2 mm




Nozzle orifice approx. 0.46 - 0.53 mm (= 0.018 - 0.021 in)Nozzle pressure 15 MPa (= approx. 150 bar; 2176 p.s.i.)

only for spot repair and stripe coatingRecommended thinner Thinner 91-92


Thinner 90-53



dft in m 100 125


Overcoating table for Phenguard 935

substrate

temperature

10C 15C 20C 30C 40C





Pot lifeInduction time

AIR SPRAY

AIRLESS SPRAY

BRUSH/ROLLER

CLEANING SOLVENT


42/1103

July 2012

page 3/5

PHENGUARD 930

Curing table for Phenguard tankcoating system before transport of

cargoes without note 4, 7, 8 or 11 and ballast water and tanktest with seawater


10C 14 days

15C 14 days

20C 10 days

30C 7 days

40C 5 days

minimum curing time of Phenguard tankcoating system before transport of

cargoes with note 4, 7, 8 or 11: 3 months for detailed information on resistance and resistance notes, please refer to

the latest issue of the Cargo Resistance List for transport of methanol and vinyl acetate monomer, a hot cure is required

which cannot be substituted by a service period of 3 months with non-aggressive cargoes

adequate ventilation must be maintained during application and curing(please refer to sheets 1433 and 1434)

the performance of the applied system strongly depends on the curingdegree of the first coat at time of recoating. Therefore overcoating time

between 1st and 2nd coat is extended in comparison between 2nd and 3rdcoat (see overcoating details)

when used as a primer under solvent free tank-linings the dft must be limitedto a maximum of 100 m


10 C 6 hours

20 C 4 hours

30 C 1.5 hour

Whilst it is always the aim of Sigma Coatings to supply the same product on aworldwide basis, slight modification of the product is sometimes necessary to

comply with local or national rules/circumstances.Under these circumstances an alternative product data sheet is used.

Curing



43/1103

July 2012

page 4/5

PHENGUARD 930

Conversion tabels see information sheet 1410







this is a solvent borne paint and care should be taken to avoid inhalation ofspray mist or vapour as well as contact between the wet paint and exposed

skin or eyes

REFERENCES

SAFETY PRECAUTIONS


44/1103

July 2012

page 5/5

PHENGUARD 930

WARRANTY



infringement of any U.S. patent covering the product.

THESE ARE THE ONLY WARRANTIES THAT PPG MAKES AND ALL OTHER EXPRESS OR IMPLIED WARRANTIES,

UNDER STATUTE OR ARISING OTHERWISE IN LAW, FROM A COURSE OF DEALING OR USAGE OF TRADE,

INCLUDING WITHOUT LIMITATION, ANY OTHER WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE OR USE, ARE

DISCLAIMED BY PPG.

Any claim under this warranty must be made by Buyer to PPG in writing within five (5) days of Buyers discovery of the claimed

defect, but in no event later than the expiration of the applicable shelf life of the product, or one year from the date of the

delivery of the product to the Buyer, whichever is earlier. Buyers failure to notify PPG of such non-conformance as required

herein shall bar Buyer from recovery under this warranty.


IN NO EVENT WILL PPG BE LIABLE UNDER ANY THEORY OF RECOVERY (WHETHER BASED ON NEGLIGENCE OF

ANY KIND, STRICT LIABILITY OR TORT) FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES

IN ANY WAY RELATED TO, ARISING FROM, OR RESULTING FROM ANY USE MADE OF THE PRODUCT.

The information in this data sheet is intended for guidance only and is based upon laboratory tests that PPG believes

to be reliable. PPG may modify the information contained herein at any time as a result of practi cal experience and




knowledge and industrial skills i n the industry and it is the end-users responsibility to determine the suitability of the

product for its own particular use and it shall be deemed that Buyer has done so, as its sole discretion and risk.



resulting from such use or the contents of this data sheet (unless there are written agreements stating otherwise).Variations in the application environment, changes in procedures of use, or extrapolation of data may cause

unsatisfactory results.

This data sheet supersedes all previous versions and it is the Buyers r esponsibility to ensure that this data sheet

is current prior to using the product. Current data sheets for all PPG Protective & Marine Coatings products are

maintained at www.ppgpmc.com.

The English text of this data sheet shall prevail over any translation thereof.

PDS 7409

180706 offwhite 7001002200


45/1103


46/1103

November 2012

page 1/5

5 pages

Revision of July 2012

PHENGUARD 935

two component high build amine adduct cured novolac phenolic epoxy coating

second coat in the Phenguard tankcoating system





pink eggshell



1.7 g/cm66% 2%

max. 191 g/kg (Directive 1999/13/EC, SED)max. 315 g/l (approx. 2.6 lb/gal)

Recommended dry film thickness 100 m *Theoretical spreading rate 6.6 m/l for 100 m *

2 hours at 20 Cmin. 24 hours *

max. 21 days *see curing table *



previous coat of Phenguard 930; dry and free from any contamination

the substrate must be perfectly dry before and during application of

Phenguard 935

substrate temperature must be above 10C and at least 3C above dewpoint during application and curing

marine system sheet: 3141tankcoatings system sheet: 3322

Description


COLOURS AND GLOSS

BASIC DATA AT 20 C


VOC (Directive 1999/13/EC, SED)VOC (UK PG 6/23(92) appendix 3)


Full cure after


RECOMMENDED

SUBSTRATE CONDITIONS

AND TEMPERATURES



47/1103

November 2012

page 2/5

PHENGUARD 935


the temperature of the mixed base and hardener should preferably beabove 15C, otherwise extra solvent may be required to obtain application

viscosity too much solvent results in reduced sag resistance and slower cure

thinner should be added after mixing the components

allow induction time before use15C - 20 min.

20C - 15 min.25C - 10 min.

4 hours at 20 C*see additional data



Nozzle orifice 2 mm


Recommended thinner Thinner 91-92Volume of thinner 0 - 10%, depending on required thickness and application conditions


Nozzle pressure 15 MPa (= approx. 150 bar; 2176 p.s.i.)



Thinner 90-53


theoritical spreading rate m/l 6.6 5.3

dft in m 100 125



Induction time

Pot life

AIR SPRAY

AIRLESS SPRAY

BRUSH/ROLLER

CLEANING SOLVENT


48/1103

November 2012

page 3/5

PHENGUARD 935



10C 15C 20C 30C 40C




Min.curing time of Phenguard tankcoating system before transport of

cargoes without note 4, 7, 8 or 11 and ballast water and tanktest with sea

water


10C 14 days

15C 14 days

20C 10 days

30C 7 days

40C 5 days



the latest issue of the Cargo Resistance List

for transport of methanol and vinyl acetate monomer, a hot cure is requiredwhich cannot be substituted by a service period of 3 months with non-

aggressive cargoes adequate ventilation must be maintained during application and curing

(please refer to sheets 1433 and 1434) the performance of the applied system strongly depends on the curing

degree of the first coat at time of recoating. Therefore overcoating timebetween 1st and 2nd coat is extended in comparison between 2nd and 3rd

coat (see overcoating details)


10 C 6 hours

20 C 4 hours

30 C 1.5 hour

Curing


49/1103

November 2012

page 4/5

PHENGUARD 935




Conversion tabels see information sheet 1410Explanation to product data sheets see information sheet 1411

Safety indications see information sheet 1430Safety in confined spaces and health safety

Explosion hazard - toxic hazard see information sheet 1431Safe working in confined spaces see information sheet 1433

Directives for ventilation practice see information sheet 1434



for paint and recommended thinners see safety sheets 1430, 1431 and

relevant material safety data sheets this is a solvent borne paint and care should be taken to avoid inhalation of

spray mist or vapour as well as contact between the wet paint and exposedskin or eyes


REFERENCES

SAFETY PRECAUTIONS


50/1103

November 2012

page 5/5

PHENGUARD 935

WARRANTY




























PDS 7435

179115 pink 6007002200


51/1103


52/1103

July 2012

page 1/5

5 pages


PHENGUARD 940

two component high build amine adduct cured novolac phenolic epoxy finish

finish coat in the Phenguard tankcoating system




good application properties, resulting in a smooth surface easy to clean

light grey eggshell



1.7 g/cm

66% 2%max. 191 g/kg (Directive 1999/13/EC, SED)

max. 315 g/l (approx. 2.6 lb/gal)Recommended dry film thickness 100 m *

Theoretical spreading rate 6.6 m/l for 100 m *2 hours at 20 C

min. 24 hours *

max. 21 days *

see curing table * at 20 C* see additional data


previous coat of Phenguard 935; dry and free from any contamination the substrate must be perfectly dry before and during application of

Phenguard 940 substrate temperature must be above 10C and at least 3C above dew

point during application and curing

Description


COLOURS AND GLOSS

BASIC DATA AT 20 C

Mass density

Volume solidsVOC (Directive 1999/13/EC, SED)

VOC (UK PG 6/23(92) appendix 3)

Touch dry after


Full cure after



AND TEMPERATURES


53/1103

July 2012

page 2/5

PHENGUARD 940

marine system sheet: 3141

tankcoatings system sheet: 3322

mixing ratio by volume: base to hardener 88 : 12 the temperature of the mixed base and hardener should preferably be

above 15C, otherwise extra solvent may be required to obtain applicationviscosity


4 hours at 20 C **see additional data

allow induction time before use

15C - 20 min. 20C - 15 min.

25C - 10 min.



Nozzle orifice 2 mm





Nozzle pressure 15 MPa (= approx. 150 bar; 2176 p.s.i.)



Thinner 90-53



dft in m 100 125




Pot life

Induction time

AIR SPRAY

AIRLESS SPRAY

BRUSH/ROLLER

CLEANING SOLVENT


54/1103

July 2012

page 3/5

PHENGUARD 940



10C 15C 20C 30C 40C




Min.curing time of Phenguard tankcoating system before transport of

cargoes without note 4, 7, 8 or 11 and ballast water and tanktest with sea

water


10C 14 days

15C 14 days

20C 10 days

30C 7 days

40C 5 days



the latest issue of the Cargo Resistance List

for transport of methanol and vinyl acetate monomer, a hot cure is requiredwhich cannot be substituted by a service period of 3 months with non-

aggressive cargoes adequate ventilation must be maintained during application and curing

(please refer to sheets 1433 and 1434) the performance of the applied system strongly depends on the curing

degree of the first coat at time of recoating. Therefore overcoating timebetween 1st and 2nd coat is extended in comparison between 2nd and 3rd

coat (see overcoating details)


10 C 6 hours

20 C 4 hours

30 C 1.5 hour

Whilst it is always the aim of Sigma Coatings to supply the same product on a

worldwide basis, slight modification of the product is sometimes necessary tocomply with local or national rules/circumstances.


Curing



55/1103

July 2012

page 4/5

PHENGUARD 940

Conversion tabels see information sheet 1410







this is a solvent borne paint and care should be taken to avoid inhalation ofspray mist or vapour as well as contact between the wet paint and exposed

skin or eyes

REFERENCES

SAFETY PRECAUTIONS


56/1103

July 2012

page 5/5

PHENGUARD 940

WARRANTY



infringement of any U.S. patent covering the product.

THESE ARE THE ONLY WARRANTIES THAT PPG MAKES AND ALL OTHER EXPRESS OR IMPLIED WARRANTIES,

UNDER STATUTE OR ARISING OTHERWISE IN LAW, FROM A COURSE OF DEALING OR USAGE OF TRADE,

INCLUDING WITHOUT LIMITATION, ANY OTHER WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE OR USE, ARE

DISCLAIMED BY PPG.

Any claim under this warranty must be made by Buyer to PPG in writing within five (5) days of Buyers discovery of the claimed

defect, but in no event later than the expiration of the applicable shelf life of the product, or one year from the date of the

delivery of the product to the Buyer, whichever is earlier. Buyers failure to notify PPG of such non-conformance as required

herein shall bar Buyer from recovery under this warranty.


IN NO EVENT WILL PPG BE LIABLE UNDER ANY THEORY OF RECOVERY (WHETHER BASED ON NEGLIGENCE OF

ANY KIND, STRICT LIABILITY OR TORT) FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES

IN ANY WAY RELATED TO, ARISING FROM, OR RESULTING FROM ANY USE MADE OF THE PRODUCT.

The information in this data sheet is intended for guidance only and is based

Sigma Coating s

Documents

Transcript of Sigma Coating s