Download - Planning and Execution of Ground Mount Solar Projects ... · 01 basics of ground mount solar projects. your logo basics units of electricity page 05 • Voltage, V(measured in Volts,

your logo

prepared forgeneral audience

Planning and Execution of Ground Mount Solar Projects(“Solar 101”)

your logo

intropurpose

page02

This presentation provides an overview of key concepts related to the planning, design and construction of ground mount solar projects intended for a non-technical audience.

your logo

introoverview

page03

01 basics of a ground mount solar project 02 project planning

01 basics of groundmount solar projects

your logo

basicsunits of electricity

page05

• Voltage, V (measured in Volts, V)• potential difference between two

points

• Current, I (measured in Amps, A)• rate of flow of electrons

• Resistance, R (measured in Ohms, Ω)• resistance to electron flow of a

material

V = I x R

Image Source: https://learn.sparkfun.com/tutorials/voltage-current-resistance-and-ohms-law

Water analogy:

your logo


page06

• Voltage is either AC (Alternating Current) or DC (Direct Current).

• In a solar project, the inverters convert from the DC output of the solar panels to AC for use by the grid.

• AC can be single phase or 3 phase.

Image Source: https://learn.sparkfun.com/tutorials/alternating-current-ac-vs-direct-current-dc

your logo


page07

• Power, P (measured in Watts, W)• rate of transfer of electrical energy

• Power losses depend on the current and resistance of a circuit.

For DC systems:

P = I x V Ploss = I2 x R

• Losses can be decreased by using bigger cables (lower resistance) or higher voltage (lower current).

• Transformers change AC voltage for transmission of power over long distances.

your logo


page08

• In AC systems, power can be • Apparent Power, S (measured in Volt-

Amperes, VA)• Real Power, P (measured in Watts, W)• Reactive Power, Q (measured in

reactive Volt-Amperes, VAR)

• Power (P) is what generates kWh ($$$).• But electrical equipment (inverters,

transformers) is rated for the Apparent Power (S), which determines current.

For 3-Phase AC Systems:

S = √3 I x V, Ploss = 3 I2 x R

your logo


page09

• Power Factor, pf, is the ratio of Real Power to Apparent Power.

• Power Factor can be positive (“lagging”) or negative (“leading”) depending on the relationship between the current and voltage.

• Utilities typically specify the power factor for a solar generator while requiring capability to change power factor within a specified range, for example, from -0.95 to +0.95.

• Power factor control is done by the inverters or by power factor correction equipment installed at the substation.

Image By Wikieditor4321 - Own work, CC BY-SA 4.0, https://commons.wikimedia.org/w/index.php?curid=45518724

pf = P / Spf = cos (θ)

your logo

basicssimple schematic

page010

.

.

.

RecombinerBox

CombinerBoxes

Intermediate Transformer

InverterStrings of Solar Panels

.

.

.

. . .

. . .

DC Collector

AC Collector

MMain Step-Up Transformer

Protections, Controls, and Communications

Connection to Grid

Inverter Stations

your logo


page011

.

.

.

RecombinerBox

CombinerBoxes



.

.

.

. . .

. . .

DC Collector

AC Collector



Connection to Grid

Inverter Stations

Each panel generates ~40V, 8.5A. They are connected in series to form “strings”

your logo


page012

.

.

.

RecombinerBox

CombinerBoxes



.

.

.

. . .

. . .

DC Collector

AC Collector



Connection to Grid

Inverter Station

Output of strings is combined in parallel at combiner boxes and recombiner boxes.

your logo


page013

.

.

.

RecombinerBox

CombinerBoxes



.

.

.

. . .

. . .

DC Collector

AC Collector



Connection to Grid

Inverter Station

Maximum Power Point Inverters have two functions

• Convert the dc power into ac.• Control the dc voltage from

the solar array to track the “maximum power point” or curtail the power.

your logo


page014

.

.

.

RecombinerBox

CombinerBoxes



.

.

.

. . .

. . .

DC Collector

AC Collector



Connection to Grid

Inverter Stations

Larger projects have multiple subarrays each connected to its own inverter station. Multiple inverter stations are connected to form a “collector system”.

your logo


page015

.

.

.

RecombinerBox

CombinerBoxes



.

.

.

. . .

. . .

DC Collector

AC Collector



Connection to Grid

Inverter Stations

One or more transformers step up the voltage to grid level.

your logo


page016

.

.

.

RecombinerBox

CombinerBoxes



.

.

.

. . .

. . .

DC Collector

AC Collector



Connection to Grid

Inverter Station

A substation contains the main transformer together with protections and controls equipment required to connect the project safely to the grid.

A substation without a transformer is called a “switching station”.

your logo

basicspiles

page017

• Different types• Driven piles• Helical piles (1 or more helixes)• Ground screws• Caisson piles• Rock anchors• Or none at all (ballasted system)

• Selection depends on• Frost depth• Presence of boulders• Type of soil / presence of bedrock

• Subsurface risk can impact project cost and schedule.

your logo

basicsgrid interconnection

page018

• Point of Common Coupling (PCC) is where the ownership changes from customer to utility. • Point of Interconnection (POI) is where the project connects to the existing grid.• PCC and POI can be in different locations if a new utility-owned line is required to connect the project.

Image Source: Hydro One, Form B, Connection Impact Study Application

02 project planning

your logo

planning key principles

page020

• The best practice for engineering of large capital projects involves a phased approach that begins with Front End Engineering Design or FEED, also called Front End Loading.

• The work completed in each phase is just enough to allow decisions to be made and the project advanced.

FEL1Conceptual

Gate Review

FEL2Pre-

FeasibilityGate

ReviewFEL3

FeasibilityGate

ReviewFEL4

ExecutionStart Up and Operations

Value Identification Value Realization

your logo

planningkey principles

page021

• In each phase, uncertainty decreases and so does project risk.

• As uncertainty decreases, precision of estimates improves (project yield, CAPEX, OPEX)

Image source: http://wiki.iploca.com/display/rtswiki/2.2+Key+points+to+address+during+FEL

your logo

planningkey principles

page022

• A gate review is completed after each phase to determine whether to move forward to the next phase.

• The gate review is linked to a spending decision.

Image source: http://www.chem.info/article/2013/12/right-tools-job-front-end-loading

your logo

planningFEL 1 - concept

page023

Typical tasks:

• Land constraints → Environmental constraints → Available Area→ Estimate DC capacity

• Off-taker constraints• Interconnection availability→ Estimate maximum AC capacity

→ Ballpark energy production→ Ballpark CAPEX, OPEX estimates

→ Preliminary financial analysis

Go / No Go Decision

CAPEX~ $/W

Capacity ~MW/ha

Yield ~kWh/kW

your logo

planningFEL 2 – pre-feasibility

page024

Typical tasks:

• Environmental site investigation(s)• Desktop geotechnical• Develop layout• Develop single line diagram• Choice and budgetary quotations for

major equipment• PV Modules• Racking• Inverters

→ More precise energy yield and cost estimates

→ More precise financial analysis

Go / No Go Decision

your logo

planningFEL 3 - feasibility

page025

Typical tasks:

• Off-take agreements awarded / final.• Interconnection studies.→ Interconnection agreement• Site work, studies and consultations.→ Environmental & regulatory permits.• Geotechnical investigation.

• Prepare EPC contract designs and specifications.

→ Request for proposals.→ Bid analysis and selection.

→ More precise energy yield and cost estimates

→ More precise financial analysis

Go / No Go Decision

your logo

planningFEL 4 - execution

page026

Typical tasks:

• Project finance review and credit agreement execution.

• Kick-off with EPC Contractor.• Construction planning (safety, quality,

staffing).• Detailed design & engineering (50%,

90%, Issued for Construction).→ Building permits.

• Procurement.• Construction.• Testing & commissioning.• Project start-up.

Operations.

your logo

planninga brief word on energy storage…

page027

• An energy storage system has both a Power rating (Watts) and Energy rating (Watt-hours or Wh)

• Multiples types of energy storage might be appropriate for the same application.

• To select and optimize the energy storage device, first you need to develop specifications.

Image source: http://www.sandia.gov/ess/publications/SAND2013-5131.pdf

your logo

• Consider:• Stakeholder objectives• System requirements• Load/generation profile• Costs (capital + operational)

vs benefits• Operational requirements• Replacement frequency• Technology risk• Environmental risk• And more

planninga brief word on energy storage…

page028Image source: http://www.sandia.gov/ess/publications/SAND2013-5131.pdf

thank you.