MACtac TECHNICAL ProductsInnovative Supplier of Engineered Pressure Sensitive Adhesives
Product Selector - April 2012
pg. 2
Phone: 1-800-328-2619
Specialty Products Table of Contents
page
Corporate Overview 3
Technical Adhesive Constructions Single-Coated & Double-Coated 4 Free Film 4
Technical Carrier Membranes Paper, Film, Foam and Other Carriers 5
Technical Liner Categories Densified Kraft Paper Liners 6 Polycoated Kraft Paper Liners 6 Coated Kraft Lineers 6 Film Liners 7 Other Liners 7
Test Methods Peel, Shear 8 Quick Tack, Release, Other Methods 9
MACbond® 10 Rubber, Double-coated Films, Single Liner IB1101A, IB1111A, IB1161 11 IB1175AER, IB1175AERW60, IB1175AL12 12 IB1178A, IB1178AW60, IB1182 13 IB1182W60, IB1183, IB1183W60 14 IB1184W60, IB1185L12, IB1188 15 IB1190A, IB1190AW60, IB1190AP2 16 IB1200A, iB1271 IB1271W60 17
Acrylic, Double-coated Films, Single Liner IB2100, IB2101, IB2130 18 IB2132, IB2133 19 IB2141, IB2154, IB2180N 20
Acrylic, Double-coated Films, Double Liner IB2107 21
Specialty Permanent/Removable IB1250TR 22 Rubber Blackbond IB1419A 22 Rubber with Tissue Carrier IB1690A 23 Rubber with SWV Carrier IB1950 23 Optically Clear IB2104 24 Rubber/Acrylic IB2125A 24 Acrylic Blackbond IB2408 24 Heat Seal Film/Acrylic PSA IB2711A 25 Acrylic with Scrim Carrier IB6205W50 25 IB6280W50 25 Prefinished IB1182PS, IB1190APS 26 SB1786 27
page
MACfilm® 28 Rubber, Free Films, Single Liner IF1092A, IF1093A-80 29
Acrylic, Free Films, Single Liner IF20V2, IF2012A, IF2013A 30 IF2013AP2 IF2015A, IF2071 31 IF2092, IF2095 32
Acrylic, Free Films, Double Liner IF2043B, IF3041, IF3041TF 33
MACmount® 34 Rubber, Double-coated Foams, Single Liner IM1705A, IM1800A, IM1801A 35 IM1810A, IM1830A, IM1900A 36 IM1930A, IM1940A 37
Acrylic, Double-coated Foams, Single Liner IM2901, IM29078N, IM2908-80 38 IM2920, IM2940 39
GS Series 40 High-Strength Adhesive Tapes GS2004, GS21003 41 GS1001, GS1013, GS1039, GS1019 42 GS1004, GS1007, GS2906 43
Phenolic Tapes 44 Phenolic IF4020A, IF4023A 45
Safety Grit 46 IC6187 47
Application Ideas Building & Construction 48 Appliance 49 RV & Marine 50 Automotive 51
Adhesive Recommendations Foam Fabrication 52
Basket of 12 MACtac® Products You Should Know 53
Conversions & Fractions Charts 54-56
Credit Application 57-58
Additional Information 59
Packaging & Labeling 60-61
pg. 3
Specialty Products
email: [email protected]. MACtac.com/technical
Corporate Overview
MACtac® Specialty Products has been a trusted source of pressure sensitive adhesive materials for over 50 years. Our engineered adhesive solutions are a key component in mounting, laminating, bonding, and fastening for converters and OEM’s in a wide range of markets and applications. Markets served include but are not limited to appliance, automotive, gasket fabrication, alternative energy, construction, and aerospace. Our expertise in adhesive coating and our state-of-the-art technology expands functionality, inspires new product designs, and delivers speed to solutions – cost effectively. We offer a wide range of adhesive single- and double-coated films and foams to fit in a variety of applications.
•State-of-the-artadhesivecoatingfacilities
•Dedicatedresearchanddevelopment
•Dedicatedsalesandtechnicalsupport
•Customizablesolutions
MACtac’s core competency is pressure sensitive adhesive coating and we look forward to providing you the adhesive solution that best fits your need. Please use this book as a reference for choosing the correct product for your application. If you have any questions or if there is a specific solution you are looking for please contactMACtacSalesat800-328-2619.
Thank you,
Justin Kalvitz General Manager Specialty & Retail
Customer Service 800-321-0011
Fax 888-821-8834
Email [email protected]
Aerospace
Appliance
Automotive/Recreation
Construction
Electronics
Glasses
General Manufacturing
Plate Mounting
UL Listed
pg.4
Phone: 1-800-328-2619
Specialty Products TechnicalAdhesiveConstructions
Single-CoatedSingle-coated adhesive products consist of a flexible face stock material that is coated on one side with a pressure sensitive adhesive which is used to bond the
product to a substrate. The adhesive is typically protected by a release liner which is removed and discarded at the time of installation. On a single-coated adhesive product the face stock typically performs a unique function. A good example is the MACtac® Black Grit safety products.
Double-CoatedDouble-coated adhesive products consist of a fairly thin, flexible carrier membrane that is coated on both sides with a pressure sensitive adhesive.
Double-coated adhesives are designed to bond two substrates either similar or dissimilar in nature together. Double-coated adhesive constructions are highly customizable to meet end user requirements. The two adhesive layers can be the same or different adhesives. The proper selection will provide the correct
gap filling and will ensure the optimum adhesive contact with each substrate. MACtac double-coated adhesive products are ideal for gasket bonding, insulation materials, bonding electronic components, attaching molding, extruded plastic parts and more.
FreeFilmFree film adhesive products consist of a layer of pressure sensitive adhesive on a release liner without a carrier membrane. The lack of a carrier allows the
adhesive to be more extensible and conformable. Free film adhesives are designed to bond two substrates either similar or dissimilar in nature together. MACtac free film adhesive products are ideal for mounting nameplates, second surface printed signs or labels, and other decorative substrates.
AdhesiveCarrier
AdhesiveLiner
Face StockAdhesive
Liner
Adhesive
Liner
pg. 5
Specialty Products
email: [email protected]. MACtac.com/technical
TechnicalCarrierMembranes
Acarriermembranecanbeanyrelativelythin,flexiblematerialsuchaspaper,filmorfoam.Theterm“carrier”usuallyreferstomaterialthathasbeencoatedonbothsideswithadhesive.Acarrier’sprimaryfunctionistocarrytheadhesivebutacarrieralsoprovidesreinforcingstrength,gapfillinganddimensionalstabilitytotheproduct.
Paper CarriersPaper carrier membranes are composed of cellulose fibers and differ from one another by weight, degree of chemical treatment, thickness and color. Based on the thickness they provide paper carriers are a sound economical choice.
FilmCarriersFilm carrier membranes are composed of various forms of thin plastic such as polyester, polypropylene, polyethylene, and polyvinylchloride. The films differ by thickness, chemical resistance, barrier properties, tensile strength, temperature resistance, and color. An added benefit of a film carrier is it is water resistant.
Polyester(PET)Films: PET film carriers are clear films that offer high tensile strength and can be used with most adhesive technologies. PET films also provide good barrier properties to most migratory chemicals.
Polypropylene(PP)Films: PP film carriers are available in oriented and non-oriented versions. Most manufactures use clear PP films but white and colored films are also available. Both oriented and non-oriented films are water resistant and neither provides sufficient barrier properties for migratory chemicals.
Polyethylene(PE)Films: Polyethylene (PE) Films: PE films are available in oriented and non-oriented versions. Most manufactures use clear PE films but white and colored films are also available. Both oriented and non-oriented films are water resistant and neither provides sufficient barrier properties for migratory chemicals. PE films are similar to PP films but are more easily stretched and relatively inexpensive.
Polyvinylchloride(PVC)Films:PVC films are available in hard (semi-rigid) and soft formulations. Hard PVC is less conformable and has a higher tensile strength so it is not right for all applications. However, it is also less plasticized and offers better adhesive compatibility. Soft PVC is more conformable but because of the plasticizers prevents the use of certain adhesives. PVC films are available in clear, white, and colored versions.
FoamCarriersFoam carrier membranes are composed of various forms of plastic such as polyethylene, polyvinylchloride, urethane, and neoprene. Foam carriers are designed to provide the necessary thickness to fill a gap between two surfaces that are bonded. Foams are conformable and permit surface contact between uneven or irregular surfaces and they also provide insulating and shock absorbing properties.
Polyethylene(PE)Foam:PE foam is cross-linked, closed cell foam widely used by manufactures to produce double-coated mounting foams and single-coated tapes for a variety of industrial applications.
Polyvinylchloride(PVC)Foam:PVC foam is used by manufactures to produce single- and double-coated mounting tapes. PVC foams offer a combination of softness and strength and is a good fit for certain applications.
UrethaneFoam:Urethane foams are available in ester and ether form. They are available in many thicknesses and densities and designed to work for specific applications.
NeopreneFoam:Neoprene foams are used to produce double-coated mounting foams for special applications. These foams are not used extensively but are available. Neoprene foams are strong and provide excellent chemical resistance.
OtherCarriersScrim: Scrim woven materials consist of threads of material that are woven into a variety of patterns. The patterns that are formed can be squares, rectangles, diamonds and other geometric shapes. The threads are typically spaced to form a wide open weave. Scrims primary purpose is to provide reinforcing strength to the adhesive.
pg.6
Phone: 1-800-328-2619
Specialty Products TechnicalLinerCategories
DensifiedKraftPaperLinersDensified kraft liners are semi-bleached papers that have been super calendered to produce a high-density sheet with relatively low porosity. Because of their low porosity, these papers can be coated with silicone release on either or both sides. They are commonly referred to as “SCK,” which stands for Super Calendered Kraft.
60#SCK:This liner is the “workhorse” in double-coated adhesive products. It has a balanced combination of good economy and enough thickness to allow most kiss cutting, and good tensile strength for good web processing.
80#SCK:This liner is used when even more additional liner thickness is required. It will provide easier die-cutting processes and easier removal during assembly since it is thicker and stiffer.
PolycoatedKraftPaperLinersThis family of liners combines the properties of paper and polyethylene to produce a dimensionally stable product that provides excellent thickness and easy release characteristics with an improved level of moisture stability.
72#PCK:This white polycoated liner is capable of being coated with release on both sides and, therefore, can be used in single-liner, self-wound tape constructions. It provides good moisture stability and is approximately 6.0 mils thick.
83#PCK:This is a brown, unbleached, polycoated paper. It can be release coated on both sides for use in self-wound tapes. However, it can also be coated on one side only, if required. It has a thickness of approximately 6.4 mils..
90#PCK:This polycoated release liner is considered a premium product for use on sheeted products because of its dimensional stability, white color, layflat characteristics and easy release properties. It can be coated with release on only one side, which precludes its use in self-wound constructions. Its moisture stability is apparent in processes that require subsequent drying, such as in the screen printing industry. It is approximately 6.9 mils thick.
12ptBoard:Polycoated, unbleached (brown) 12pt kraft board liners are available release coated on both sides for use in double-sided adhesive constructions. They are used primarily for their thickness and stiffness. In the gasketing industry, the thicker liner permits easier and faster steel rule die set-up. Once the gasket is cut, the stiffness of the liner allows the converter to provide several gaskets on a sheet that can be easily handled by the end user.
pg. 7
Specialty Products
email: [email protected]. MACtac.com/technical
TechnicalLinerCategories
CoatedKraftLinersCoated Kraft liners are bleached papers with a clay coating on one side. The clay coating is necessary to produce a good hold out from the silicone release since these papers are more porous than the densified Kraft papers.
80#CCK:This liner is the predominant choice for most sheeted products. Its thickness is approximately 4.8 mils. It can be “kiss cut” in the traditional manner and cut against as done in computer graphics.
60#CCK:This liner can be used when a more economical liner is required. Lighter weight and lower thickness of 3.6 mil has good “kiss cutting” properties. This liner has high tensile strength for good web processing.
FilmLinersFilm liners provide excellent moisture resistance and typically lend themselves to producing a super smooth adhesive.
Polyester(PET): PET liners are very stable, providing high tensile and tear strength while maintaining total clarity. PET liners can be easily handled in both the coating and converting processes without shrinking or expanding. Polyester liners can be coated on both sides and are moisture resistant.
LowDensityPolyethylene(LDPE): Low density film has excellent extensibility producing a very conformable liner. It has potential for stretching when exposed to stress of high temperature but is beneficial when the bonded part with liner in place needs to be formed. It is supplied as clear or opaque and is moisture resistant.
High DensityPolyethylene(HDPE):High density film is much stronger and less elastic than low density but is less conformable. Its higher density tolerates higher temperatures which permits processing through coater ovens without dramatically stretching the film. HDPE films are water resistant.
pg. 8
Phone: 1-800-328-2619
Specialty Products TestingMethods
The four tests that most accurately gauge PSA product performance in standard applications are:
PeelAdhesionThis test measures the force required to remove a pressure sensitive tape from a substrate at a controlled angle, standard rate and condition.
• Peelangle (Std.is180,90degrees)• Substrate (Std.isstainlesssteel)• Peelrate (Std.is12in./min)• Residencetime (30min.,24hr.,etc.)• Testenvironment (Std.is72°F/50%R.H.)• Bondingprocedure (Mustbedefined)• Sampledimensions (Std.is1”wide)Peel adhesion is normally expressed in pounds per inch width
(lbs./inch).
ShearAdhesionAlso referred to as holding power or creep resistance, this test measures the ability of a tape to resist the static forcesappliedinthesameplaneasthefaceorcarrier.Resultsareusuallyexpressedintimerequiredforagivenweight to cause a given amount of tape to come loose from a vertical panel.
• Substrate (Std.isstainlesssteel)• Bondingprocedure (Mustbedefined)• Sampledimension (Dimensionsofbondedarea)• Testenvironment (Temperature/humidity)• Sheardirection (Vertical/horizontal)Shear is typically expressed in “hours to fail.”
Stainless SteelTest Panel
Adhesive Sample Supported with 2.0 mil PET Backing
Adhesive Surface in Contact with Test Panel
Force
Adhesive TapeSupported by2.0 mil PET
Standard WeightStainless SteelTest Panel
pg.9
Specialty Products
email: [email protected]. MACtac.com/technical
TestingMethods
Quick TackThis refers to the properties that allow a PSA to adhere to a surface under very light pressure. It is determined by the ability of the adhesive to quickly wet the surface contacted.
• Type tack test a. Loop Tack b.RollingBall c. Polyken Probe d. Finger Tack• Substrate (Std.isstainlesssteel)
ReleaseA measure of the force per unit width required to break the bond between the PSA and the protective liner, this test incorporates rate of separation, angle of separation and width of the sample. With this test, it is important to consider the separation rate as speeds may not be consistent between testers.
• Rateofseparation • Angleofseparation • Widthofsample
MACtac® Method: MACtac relies on the Scott ReleaseTest. It specifies a separation rate of 32 ft./min.,a 180 degree angle and a 2” wide sample. The force of separation is expressed as “grams per 2” width.”Commonspeedsinclude32ft./min.,12in./min.and300in./min.Varyingthespeedwillproducedifferentresults.
OtherTestMethodsAdditional testing methods are also used to measure:
• TensileStrength• Elongation• TearStrength• Thickness• Shrinkage• Weatherometer• QUV
Adhesive TapeSupported by2.0 mil PET
Adhesive Surfacein Contact with Test Area
Force
pg.10
Phone: 1-800-328-2619
MACbond®
MACbonddouble-coatedfilmtapes– Engineered for the most demanding bonding or laminating applications, these tapes feature general purpose and high-performance rubber-based adhesives or high-performance acrylic adhesives on polyester, polypropylene or the popular Blackbond™ carrier. An enhanced product line including a scrim carrier is also available.
•Idealforalternativeenergy,transportation,electronics, construction,automotiveandappliancemarkets.
•Appliedincushioning,sealing,stiffening,sounddampening and gaskets
•Speedsassemblyandlowersmanufacturingcosts
•Replacesmechanicalfastenersandliquidadhesives
•Bondstoawiderange of surfaces
pg.11
MACbond® Rubber, Double-coated Films, Single Liner
email: [email protected]. MACtac.com/technical
IB1111A Consists of a thin polyester film carrier coated on both sides with an aggressive, rubber based pressure sensitive adhesive. The product is supplied self-wound on a densified, semi-bleached kraft release liner.
Used extensively for the mounting and bonding of flexible magnetic materials. It can also be used to bond a variety of substrates including those that are relatively rough in surface texture. This product construction has been specially designed with a tighter than normal release in order to permit processing small cut parts without the liner removing from the adhesive prematurely.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 12.5 11.0 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 9.5 9.0 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .005
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 2.0 mil / 2.0 mil 0.5 mil PET 60# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll486 0.34 10.2” 54” x 750’ 6” x 30’
AdhesiveFilm
AdhesiveSCK Liner
IB1161 IB1161 consists of a thin polyester film coated on both sides with an aggressive, general-purpose, rubber- based pressure sensitive adhesive. The product is supplied self-wound on 60# Semi-Bleached, Densified-Kraft (SCK) release liner. IB1161 provides an economical solution exhibiting moderate adhesion and shear resistance. IB1161 is intended for use as an assembly aid for bonding foam, felt, cloth, paper, primed wood, metal and many low or unplasticized plastics in gasket, seal, trim & other applications.The½milPETfilmcarrierprovidesgoodstrength/stabilityforoptimumhandlingthroughvarious slitting, laminating, die-cutting processes.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 7.0 6.5 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 5.5 5.5 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 100+ 100+ PSTC - 107
Thickness - Carrier & Adhesive .0025
Temperature Application: Above 40°F (4°C) for best results. End Use: -50° to 140°F (-29° to 60°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 1.0 mil / 1.0 mil 0.5 mil PET 60# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll540 na na 60” x 750’ 6” x 30’
AdhesiveFilm
AdhesiveSCK Liner
IB1101AA polyester film coated on both sides with a high performance, rubber based pressure sensitive adhesive. The product is supplied self-wound on a polycoated natural kraft release liner.
IB1101A exhibits outstanding shear resistance and high adhesion. The extra thick (1.0 mil) polyester carrier provides added strength and stability for optimum processing and handling.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 10.0 11.5 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 10.5 11.5 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .0046
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 1.8 mil / 1.8 mil 1.0 mil PET 83# Brown PCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll486 0.46 10.9” 54” x 750’ 6” x 30’
AdhesiveFilm
AdhesivePCK Liner
pg.12
Phone: 1-800-328-2619
MACbond® Rubber, Double-coated Films, Single Liner
pg.12
IB1175AL12
A thin polyester film coated on both sides with an aggressive, general purpose, rubber based pressure sensitive adhesive. The product is supplied self-wound on a 12 pt. polycoated two side, natural kraft release liner.
Designed for general purpose bonding applications such as in the gasket, seal, and trim markets Typically used for bonding to foams, felts, cloths, primed wood, paper, metal, plastics, and most low or unplasticized substrates. It has an excellent balance of economy versus performance. The polyester carrier provides dimensional stability and superior die cutting properties.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 7.5 10.0 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 9.5 8.5 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .0035
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 1.8 mil / 1.2 mil 0.5 PET 12pt Board -
MSI Wt/MSI Roll OD Master Roll Sample Roll486 0.60 10.0” 54” x 750’ Custom
AdhesiveFilm
Adhesive
12 pt Board
Liner
Consists of a thin polyester film coated on both sides with an aggressive, general purpose, rubber based pressure sensitive adhesive. Supplied self-wound on a densified, semi-bleached kraft liner.
Designed for general purpose bonding applications such as in the gasket, seal, and trim markets. Typically used for bonding to foams, felts, cloths, primed wood, paper, metal, plastics, and most low or unplasticized substrates. It has an excellent balance of economy versus performance. The polyester carrier provides dimensional stability and superior die cutting properties.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 11.5 11.0 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 9.5 8.5 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .0035
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 1.8 mil / 1.2 mil 0.5 mil PET 80# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll486 0.45 10.0” 54” x 750’ 6” x 30’
IB1175AER
AdhesiveFilm
AdhesiveSCK Liner
IB1175AERW60 60”Wide - Consists of a thin polyester film coated on both sides with an aggressive, general purpose, rubber based pressure sensitive adhesive. The product is supplied self-wound on a densified, semi-bleached kraft liner.
Designed for general purpose bonding applications such as in the gasket, seal, and trim markets. Typically used for bonding to foams, felts, cloths, primed wood, paper, metal, plastics, and most low or unplasticized substrates. It has an excellent balance of economy versus performance. The polyester carrier provides dimensional stability and superior die cutting properties.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 11.5 11.0 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 9.5 8.5 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .0035
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 1.8 mil / 1.2 mil 0.5 mil PET 80# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll540 0.45 10.0” 60” x 750’ 6” x 30’
AdhesiveFilm
AdhesiveSCK Liner
Contact Sales for minimums and lead time.
pg.13
MACbond® Rubber, Double-coated Films, Single Liner
email: [email protected]. MACtac.com/technical
IB1178A A thin polyester film coated on both sides with an aggressive, general purpose, rubber based pressure sensitive adhesive. The product is supplied self-wound on a densified, semi-bleached kraft liner.
Designed for general purpose bonding applications to relatively smooth surfaces. Typically, it can be used for bonding to paper, metal, plastics, and most low or unplasticized substrates. It has an excellent balance of economy versus performance. The polyester carrier provides dimensional stability and superior die cutting properties.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 11.0 11.0 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 8.5 8.5 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .0029
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 1.2 mil / 1.2 mil 0.5 mil PET 60# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll486 0.28 9.2” 54” x 750’ 6” x 30’
AdhesiveFilm
AdhesiveSCK Liner
IB1178AW60 60”Wide - A thin polyester film coated on both sides with an aggressive, general purpose, rubber based pressure sensitive adhesive. The product is supplied self-wound on a densified, semi-bleached kraft liner.
Designed for general purpose bonding applications to relatively smooth surfaces. Typically, it can be used for bonding to paper, metal, plastics, and most low or unplasticized substrates. It has an excellent balance of economy versus performance. The polyester carrier provides dimensional stability and superior die cutting properties.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 11.0 11.0 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 8.5 8.5 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .0029
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 1.2 mil / 1.2 mil 0.5 mil PET 60# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll540 0.45 10.0” 60” x 750’ 6” x 30’
AdhesiveFilm
AdhesiveSCK Liner
IB1182 A thin polyester film coated on both sides with a general purpose, rubber based pressure sensitive adhesive. The product is supplied self-wound on a 60# densified, semi-bleached kraft liner.
Designed for general purpose bonding applications such as in the gasket, seal, and trim markets. Typically used for bonding to foams, felts, cloths, primed wood, paper, metal, plastics, and most low or unplasticized substrates. It has an excellent balance of economy versus performance and can be used in many applications as an aid to assembly. The polyester carrier provides dimensional stability and superior die cutting properties.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 10.0 11.0 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 10.0 11.0 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .0034
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 1.5 mil / 1.5 mil 0.5 mil PET 60# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll486 0.30 9.5” 54” x 750’ 6” x 30’
AdhesiveFilm
AdhesiveSCK Liner
pg.14
Phone: 1-800-328-2619
MACbond® Rubber, Double-coated Films, Single Liner
IB1182W60 60”Wide - A thin polyester film coated on both sides with a general purpose, rubber based pressure sensitive adhesive. The product is supplied self-wound on a 60# densified, semi-bleached kraft liner.
Designed for general purpose bonding applications such as in the gasket, seal, and trim markets. Typically used for bonding to foams, felts, cloths, primed wood, paper, metal, plastics, and most low or unplasticized substrates. It has an excellent balance of economy versus performance and can be used in many applications as an aid to assembly. The polyester carrier provides dimensional stability and superior die cutting properties. 60” Version of IB1182.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 10.0 11.0 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 10.0 11.0 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .0034
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 1.5 mil / 1.5 mil 0.5 mil PET 60# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll540 0.30 9.5” 60” x 750’ 6” x 30’
AdhesiveFilm
AdhesiveSCK Liner
IB1183W60 60”Wide - A thin polyester film coated on both sides with a general purpose, rubber based pressure sensitive adhesive. The product is supplied self-wound on an 80# densified, semi-bleached kraft liner.
Designed for general purpose bonding applications such as in the gasket, seal, and trim markets. Typically used for bonding to foams, felts, cloths, primed wood, paper, metal, plastics, and most low or unplasticized substrates. It has an excellent balance of economy versus performance and can be used in many applications as an aid to assembly. The polyester carrier provides dimensional stability and superior die cutting properties.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 10.0 11.0 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 10.0 11.0 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .0034
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 1.5 mil / 1.5 mil 0.5 mil PET 80# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll540 0.42 11.4” 60” x 750’ 6” x 30’
AdhesiveFilm
AdhesiveSCK Liner
IB1183 A thin polyester film coated on both sides with a general purpose, rubber based pressure sensitive adhesive. The product is supplied self-wound on an 80# densified, semi-bleached kraft liner.
Designed for general purpose bonding applications such as in the gasket, seal, and trim markets. Typically used for bonding to foams, felts, cloths, primed wood, paper, metal, plastics, and most low or unplasticized substrates. It has an excellent balance of economy versus performance and can be used in many applications as an aid to assembly. The polyester carrier provides dimensional stability and superior die cutting properties.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 10.0 11.0 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 10.0 11.0 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .0034
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 1.5 mil / 1.5 mil 0.5 mil PET 80# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll486 0.33 10.2” 54” x 750’ 6” x 30’
AdhesiveFilm
AdhesiveSCK Liner
pg.15
MACbond® Rubber, Double-coated Films, Single Liner
email: [email protected]. MACtac.com/technical
IB1184W60 A thin polyester film coated on both sides with a heavy coating of an aggressive, high performance, rubber based pressure sensitive adhesive. Self-wound on an 80# densified, semi-bleached kraft liner.
Designed for the more demanding bonding applications encountered in the gasket, seal and trim lamination markets where high tack and high ultimate bond strength are required. The heavy coating of adhesive aids in bonding rough or irregular surfaces. The polyester carrier provides dimensional stability and superior die cutting properties.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 14.0 15.0 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 14.0 15.0 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .0058
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 2.7 mil / 2.7 mil 0.5 mil PET 80# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll540 0.42 11.4” 60” x 750’ 6” x 30’
AdhesiveFilm
AdhesiveSCK Liner
IB1185L12 A thin polyester film coated on both sides with a general purpose, rubber based pressure sensitive adhesive. The product is supplied self-wound on a 12 pt. polycoated two side, natural kraft release liner.
Designed for general purpose bonding applications such as in the gasket, seal, and trim lamination markets. It can be used in many applications as an aid to assembly. The polyester carrier provides dimensional stability and superior die cutting properties. The added thickness of the 12 pt. liner contributes to easy die cutting, excellent layflat of the cut sheets and quick, easy removal of the die cut parts.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 11.0 9.0 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 9.0 8.0 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .0034
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 1.5 mil / 1.5 mil 0.5 mil PET 12pt Board -
MSI Wt/MSI Roll OD Master Roll Sample Roll486 0.60 13.7” 54” x 750’ 6” x 30’
AdhesiveFilm
Adhesive
12 pt Board
Liner
IB1188 DiverseCoatWeights - A thin polyester film coated on both sides with a rubber based pressure sensitive adhesive. One side has been specially designed to provide maximum adhesion to foams, fabrics and other highly textured surfaces. The product is supplied self-wound on a 80# densified, semi-bleached kraft liner.
Designed for bonding applications such as in the gasket, seal, and trim markets. Typically used for bonding to foams, felts, cloths, primed wood, paper, metal, plastics, and most low or unplasticized substrates.Theresultingproductsaresuitableforabroadrangeofapplicationsinthegasket,sound/thermal insulation, appliance and automotive markets. The polyester carrier provides dimensional stability and superior die cutting properties.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 12.5 13.0 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 12.0 12.5 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .0046
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 2.7 mil / 1.5 mil 0.5 mil PET 80# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll486 0.37 10.8” 54” x 750’ 6” x 30’
AdhesiveFilm
AdhesiveSCK Liner
IB1190A A thin polyester film coated on both sides with an aggressive, general purpose, rubber based pressure sensitive adhesive. The product is supplied self-wound on a densified, semi-bleached kraft liner.
Designed for general purpose bonding applications such as in the gasket, seal, and trim markets. Typically used for bonding to foams, felts, cloths, primed wood, paper, metal, plastics, and most low or unplasticized substrates. It has an excellent balance of economy versus performance. The polyester carrier provides dimensional stability and superior die cutting properties.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 11.5 10.5 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 9.5 8.5 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .0035
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 1.8 mil / 1.2 mil 0.5 mil PET 60# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll486 0.30 9.5 54” x 750’ 6” x 30’
AdhesiveFilm
AdhesiveSCK Liner
IB1190AW60 60”Wide - A thin polyester film coated on both sides with an aggressive, general purpose, rubber based pressure sensitive adhesive. The product is supplied self-wound on a densified, semi-bleached kraft liner.
Designed for general purpose bonding applications such as in the gasket, seal, and trim markets. Typically used for bonding to foams, felts, cloths, primed wood, paper, metal, plastics, and most low or unplasticized substrates. It has an excellent balance of economy versus performance. The polyester carrier provides dimensional stability and superior die cutting properties.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 11.5 10.5 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 9.5 8.5 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .0035
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 1.8 mil / 1.2 mil 0.5 mil PET 60# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll486 0.30 9.5” 60” x 750’ 6” x 30’
IB1190AP2 consists of a thin polyester film coated on both sides with an aggressive, general-purpose, rubber-based adhesive. The product is supplied at 54” width in self-wound form on a C2S 2 mil PET liner.
IB1190AP2 was designed for general purpose bonding applications such as in the gasket, seal and trim markets. IB1190AP2 is typically used for bonding to foams, felts, cloths, primed wood, paper, metal and manylow/unplasticizedplastics.Thepolyestercarrierprovidesdimensionalstabilityandsuperiordiecutting properties.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 11.5 14.0 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 9.0 9.0 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .0035
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 1.8 mil / 1.2 mil 0.5 mil PET 2 mil PET -
MSI Wt/MSI Roll OD Master Roll Sample Roll486 na na 54” x 750’ Custom
AdhesiveFilm
AdhesiveSCK Liner
AdhesiveFilm
Adhesive
2.0 Mil PET Liner
AdhesiveFilm
AdhesiveSCK Liner
IB1190AP2
pg.16
Phone:1-800-328-2619
MACbond® Rubber,Double-coatedFilms,SingleLiner
Contact Sales for minimums and lead time.
pg.17
MACbond® Rubber,Double-coatedFilms,SingleLiner
email: [email protected]. MACtac.com/technical
IB1200A A thin unoriented, polypropylene film coated on both sides with a high performance, rubber based pressure sensitive adhesive. The adhesive is protected by a release treated, 60# densified kraft liner.
IB1200A demonstrates unusually high tack and peel adhesion without sacrificing shear resistance. The heavy coating weight of adhesive provides excellent bonds to both smooth and irregular surfaces. The unoriented carrier membrane permits good conformability.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 4.5 6.0 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 12.0 11.5 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .0066
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 150°F (-18° to 66°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 2.7 mil / 2.7 mil 0.9 mil PP 60# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll486 0.43 11.1” 54” x 750’ 6” x 30’
AdhesiveFilm
AdhesiveSCK Liner
IB1271 IB1271consistsofa1.0milpolyesterfilmcoatedoneachsidewithacustom-formulated,rubber-basedpressure-sensitive adhesive. It is specially designed for adhesion to low-surface-energy substrates, high shear strength and clean removability from many surfaces. The product is supplied in self-wound form on 60# semibleached, densified-kraft release liner.
Engineered as an aggressive-removable laminate. The unique adhesive adheres to a variety of substrates while the high shear and 1.0 mil PET carrier aid in removability. This engineered laminate is not recommended for removal from high-surface-energy materials such as glass. MACtac recommends testing against specific end-use application requirements to confirm acceptable removability.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 5.5 6.0 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 4.0 4.0 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .0003
Temperature Application: Above 40°F (4°C) for best results. End Use: 0°F to 150°F (-18°C to 66°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 1.0 mil /1.0 mil 1.0 mil PET 60# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll486 na na 54” x 750’ 6” x 30’
AdhesiveFilm
AdhesiveSCK Liner
IB1271W60 IB1271W60consistsofa1.0milpolyesterfilmcoatedoneachsidewithacustom-formulated,rubber-based pressure-sensitive adhesive. It is specially designed for adhesion to low-surface-energy substrates, high shear strength and clean removability from many surfaces. The product is supplied in self-wound form on 60# semibleached, densified-kraft release liner.
Engineered as an aggressive-removable laminate. The unique adhesive adheres to a variety of substrates while the high shear and 1.0 mil PET carrier aid in removability. This engineered laminate is not recommended for removal from high-surface-energy materials such as glass. MACtac recommends testing against specific end-use application requirements to confirm acceptable removability.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 5.5 6.0 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 4.0 4.0 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .0003
Temperature Application: Above 40°F (4°C) for best results. End Use: 0°F to 150°F (-18°C to 66°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 1.0 mil /1.0 mil 1.0 mil PET 60# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll540 na na 60” x 750’ 6” x 30’
AdhesiveFilm
AdhesiveSCK Liner
IB2100 A thin polyester film coated on both sides with a high performance acrylic based pressure sensitive adhesive. The product is supplied self-wound on a densified, semi-bleached kraft liner.
Typically used for industrial bonding applications where outstanding adhesion, high shear and good solvent resistance are required. The acrylic adhesive offers good clarity and has excellent resistance to U.V. light exposure. The polyester carrier provides excellent dimensional stability and die cutting properties.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 4.5 3.5 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 4.0 4.0 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .0052
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 250°F (-18° to 121°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerAcrylic 2.4 mil / 2.4 mil 0.5 mil PET 60# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll486 0.37 10.5” 54” x 750’ 6” x 30’
AdhesiveFilm
AdhesiveSCK Liner
IB2101 A thin polyester film coated on both sides with a high performance acrylic based pressure sensitive adhesive. The product is supplied self-wound on a densified, semi-bleached kraft liner.
Is typically used for industrial bonding applications where good adhesion, high shear and good solvent resistance are required. IB2101 is best suited for bonding relatively smooth surfaces and similar applications requiring a thin reinforced adhesive film. The acrylic adhesive offers good clarity and has excellent resistance to U.V. light exposure. The polyester carrier provides excellent dimensional stability and die cutting properties.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 2.5 2.4 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 3.0 3.5 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .0026
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 250°F (-18° to 121°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerAcrylic 1.1 mil / 1.1mil 0.5 mil PET 60# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll486 0.27 9.0” 54” x 750’ 6” x 30’
AdhesiveFilm
AdhesiveSCK Liner
IB2130 A thin polyester film coated on both sides with a high tack, modifiedacrylicpressure sensitive adhesive. Theproductissuppliedself-woundona74#polycoatedwhitekraftliner.
The unique acrylic adhesive bonds to a wide range of materials, including most plastics and foams. IB2130 provides the temperature resistance required by many automotive and appliance applications without sacrificing peel and tack adhesion. The polyester carrier provides excellent dimensional stability and die cutting properties.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 6.5 6.5 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 4.5 4.5 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .0037
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 250°F (-18° to 121°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerModified Acrylic 1.8 mil / 1.5 mil 0.5 mil PET 72# White PCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll486 0.42 10.9” 54” x 750’ 6” x 30’
AdhesiveFilm
AdhesivePCK Liner
pg.18
Phone:1-800-328-2619
MACbond® Acrylic,Double-coatedFilms,SingleLiner
IB2133
IB-2132 consists of a thin polyester film coated on both sides with a high tack, modified acrylic pressure sensitive adhesive. The product is supplied self-wound on an 80# densified kraft liner.
The unique acrylic adhesive bonds to a wide range of materials, including most plastics and foams. IB-2132 provides the temperature resistance required by many automotive and appliance applications without sacrificing peel and tack adhesion. The polyester carrier provides excellent dimensional stability and die cutting properties.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 5.0 3.0 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 4.0 3.5 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .0037
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 250°F (-18° to 121°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerModified Acrylic 1.9 mil / 1.6 mil 0.5 mil PET 80# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll486 na na 54” x 750’ Custom
IB2133 consists of a thin polyester film coated on both sides with a high-tack, modified-acrylic, pressure sensitiveadhesive.Theproductissuppliedinself-woundformona72#WhitePolycoatedKraftliner.
The unique acrylic adhesive of IB2133 bonds to a wide range of materials, including most solid plastics and foams. The unique acrylic adhesive used in IB2133 also provides the temperature resistance required in many automotive and appliance applications without sacrificing immediate & ultimate adhesion. The polyester carrier provides excellent dimensional stability and die cutting properties.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 6.5 7.0 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 5.0 5.5 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .006
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 250°F (-18° to 121°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerModified Acrylic 2.8 mil /2.8 mil 0.5 mil PET 74# White PCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll486 na na 54” x 750’ Custom
AdhesiveFilm
AdhesivePCK Liner
pg.19
MACbond® Acrylic,Double-coatedFilms,SingleLiner
email: [email protected]. MACtac.com/technical
AdhesiveFilm
AdhesiveSCK Liner
IB2132
Contact Sales for minimums and lead time.
Contact Sales for minimums and lead time.
pg. 20
Phone:1-800-328-2619
MACbond® Acrylic,Double-coatedFilms,SingleLiner
IB2180N A thin polyester film coated on both sides with a high tack, modifiedacrylic pressure sensitive adhesive. Theproductissuppliedself-woundona74#polycoatedwhitekraftreleaseliner.
Provides aggressive tack and peel for quick bonding and long term adhesion. The unique acrylic adhesive bonds to a wide variety of materials with exceptional adhesion to low energy surfaces such as polypropylene and polyethylene. The polyester carrier provides excellent dimensional stability and die cutting properties.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 5.5 8.5 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 6.0 8.5 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .0050
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 190°F (-18° to 88°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerModified Acrylic 2.0 mil / 2.0 mil 0.5 mil PET 74# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll486 0.45 11.4” 54” x 750’ 6” x 30’
AdhesiveFilm
AdhesiveSCK Liner
IB2154
A 4.0 mil Black HDPE film coated on both sides with high-tack, modified-acrylic pressure sensitive adhesive(PSA).Theproductissuppliedself-woundonableached,74#PE-coatedKraftreleaseliner.
The modified-acrylic adhesive bonds well to range of materials, including many plastics. IB2154 provides the temperature resistance required in many automotive, appliance and other applications without sacrificing adhesion. IB2154 was originally developed for use in exterior automotive mirror-mounting applications.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 5.0 5.0 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 5.5 5.5 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
ThicknessCarrier plus adhesiveLiner
.0080
.0055
Temperature Application: Above 50°F (10°C) for best results. End Use: 40° to 200°F (-40° to 93°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerModified Acrylic 2.1 mil / 2.1 mil 0.5 mil PET 74# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll486 0.73 13.0” 54” x 750’ Custom
AdhesiveBlack Paper
AdhesiveSCK Liner
Contact Sales for minimums and lead time.
pg.21
MACbond®
email: [email protected]. MACtac.com/technical
Acrylic,Double-coatedFilms,DoubleLiner
IB2107 A thin polyester film coated on both sides with a high performance acrylic based pressure sensitive adhesive. The product is supplied with two white kraft release liners for ease of handling and processing in a sheet form.
Typically used for industrial bonding applications where outstanding adhesion, high shear and good solvent resistance are required. The acrylic adhesive offers good clarity and has excellent resistance to U.V. light exposure. The polyester carrier provides excellent dimensional stability and die cutting properties.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 4.0 4.0 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 4.0 4.0 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .0052
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 250°F (-18° to 121°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerAcrylic 2.4 mil / 2.4 mil 0.5 mil PET 80# White CCK 80# White CCK
MSI Wt/MSI Roll OD Master Roll Sample Sheet486 0.52 13.0” 54” x 750’ 8-1/2” x 11”
CCK LinerAdhesive
FilmAdhesiveCCK Liner
pg. 22
Phone: 1-800-328-2619
MACbond® Specialty
IB1250TR Permanent/Removable A 1.0 mil carrier film coated on both sides with a pressure sensitive adhesive. The “unwind side” is an aggressive, general purpose, permanent adhesive. The “liner side” utilizes a low adhesion, removable formulation. An 80# release coated, densified kraft liner protects the adhesive.
Designed for laminating permanently to the initial substrate. The second or final bond would provide removable adhesion from most substrates. This construction permits the production of removable or repositionable products such as gaskets, protective pads, and other temporarily bonded items.
Note:“Removability”isdependentonapplicationandsurfaceconditions.Usermusttestforsuitabilityintheir specific application.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 10.0 0.5 PSTC-16
Peel Adhesion, lbs./in. Stainless Steel - 30 minutes Stainless Steel - 24 hours
8.08.0
0.41.0
PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .0033
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 150°F (-18° to 66°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber / Rem. Acrylic 1.4 mil / 0.7 mil 1.0 Clear PP 80# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll486 0.36 10.0” 54” x 750’ 6” x 30’
AdhesiveFilm
AdhesiveSCK Liner
IB1419A Rubber Blackbond A latex impregnated black paper that is coated on each side with a high performance, rubber based pressure sensitive adhesive. The product is supplied with a polycoated white kraft liner on one side and a polycoated white kraft liner on the other.
Used extensively to bond plastic and metal faceplates, nameplates, logos, and other components in the home electronics industry. The black paper carrier provides the opaque block-out characteristic required in many applications. The aggressive adhesive insures quick reliable bonding during assembly.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 7.2 7.8 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 6.6 9.9 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .0058
Temperature Application: Above 75°F (24°C) for best results. End Use: 0° to 180°F (-18° to 82°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 1.5 mil / 1.5 mil Blackbond 90# White PCK 90# White PCK
MSI Wt/MSI Roll OD Master Roll Sample Roll486 0.58 15.4” 54” x 750’ 6” x 50’
LinerAdhesive
Black PaperAdhesivePCK Liner
IB1950
pg. 23
MACbond®
email: [email protected]. MACtac.com/technical
Specialty
IB1690AR Rubber with Tissue Carrier A light weight paper stock coated on each side with an aggressive, general purpose, rubber based pressure sensitive adhesive. Each side is protected by a release coated white kraft liner.
General purpose bonding system that can be easily handled in sheet form because of the two protective release liners. The adhesive bonds to a wide variety of substrates.
Performance Test Typical Values Testing Method
Quick Tack lbs./sq. in. - Stainless Steel 5.0** PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 7.0** PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ PSTC - 107
Thickness - Carrier & Adhesive .0037
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 1.2 mil / 1.2 mil White Fiber Stock 80# White CCK 80# White CCK
MSI Wt/MSI Roll OD Master Roll Sample Roll486 0.54 12..5” 54” x 750’ 6” x 30’
**Theadhesionfrequentlyexceedsthestrengthofthepaperandresultsindelaminationintherangeof5-7lbs
LinerAdhesive
PaperstockAdhesiveCCK Liner
Rubber with PVC Carrier IB-1950 consists of a thin, white-opaque PVC film coated on both sides with an aggressive, rubber-based pressure sensitive adhesive. The product is supplied in self-wound form on a semi-bleached, 50# densified kraft paper release liner.
IB-1950 was originally designed to fasten carpet, area rugs and other soft floor coverings to a variety of hard interior and exterior flooring surfaces. IB-1950 may also be used in general-purpose gasket, seal,trimandotherbonding/die-cuttingapplications.Therubber-basedadhesivesystemworkswellwith foams, felts, cloths, primed wood, paper, metal, and plastics. The white PVC film carrier provides excellent “block-out” opacity, dimensional stability, tensile strength and die-cutting properties.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 6.5 5.5 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 6.0 5.0 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F na na PSTC - 107
Thickness - Carrier & Adhesive .00055
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 1200°F (-18° to 65°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory Liner
Rubber 0.8 mil / 0.8 mil3.25 mil Soft White
Vinyl3.2 mil SCK -
MSI Wt/MSI Roll OD Master Roll Sample Sheet486 na na 54” x 750’ Custom
AdhesiveFilm
AdhesiveSCK Liner
Contact Sales for minimums and lead time.
pg.24
Phone:1-800-328-2619
IB2408
Acrylic Blackbond A latex impregnated black paper that is coated on each side with a high performance, acrylic pressure sensitive adhesive. The product is supplied with a polycoated white kraft liner on one side and a polycoated white kraft liner on the other.
Designed to bond most plastic and metal faceplates, nameplates, logos and other components in the home electronic industry. The black paper carrier provides the opaque block-out characteristic required in many applications. The acrylic adhesive offers improved performance at elevated temperatures.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 5.8 5.0 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 6.0 5.5 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .0078
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 250°F (-18° to 121°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerAcrylic 2.4 mil / 2.4 mil Blackbond 90# White SCK 90# White SCK
MSI Wt/MSI Roll OD Master Roll Sample Roll486 0.65 16.1” 54” x 750’ Custom
LinerAdhesive
Black PaperAdhesivePCK Liner
MACbond® Specialty
IB2104 Optically Clear A thin polyester film coated on both sides with a high performance acrylic based pressure sensitive adhesive. The product is supplied self-wound on a2.0milopticallyclearPETLiner.Is typically used for industrial bonding applications where outstanding adhesion, high shear and good solvent resistance are required. The acrylic adhesive offers good clarity and has excellent resistance to U.V. light exposure. The polyester carrier provides excellent dimensional stability and die cutting properties.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 4.5 3.5 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 4.0 4.0 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .0052
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 250°F (-18° to 121°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory Liner
Acrylic 1.75 mil / 1.75 mil 1.0 mil PET 2.0 mil Optically Clear PET Liner -
MSI Wt/MSI Roll OD Master Roll Sample Sheet259.2 na na 51” x 400’ 8-1/2” x 11”
AdhesiveFilm
Adhesive
2.0 Mil PET Liner
IB2125A Rubber/Acrylic A thin polyester film coated on one side with an aggressive, modified-acrylic pressure- sensitive adhesive and on the opposite side with high-performance, rubber-resin pressure-sensitive adhesive. IB2125A utilizes an 80# SCK release liner that provides a good combination of lamination, die-cutting and end-use application performance.
The “unwind side” modified-acrylic PSA provides excellent adhesion and compatibility with a wide range of foam, sponge, rubber, cork and other gasket materials. The “liner side” rubber-based PSA provides excellent adhesive performance on many end-use substrates with exposure to demanding application conditions. The polyester carrier provides dimensional stability and superior die cutting properties.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 6.0 11.0 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 8.0 8.5 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 15+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .0035
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 160°F (-18° to 71°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerAcrylic/Rubber 1.5 mil / 1.5 mil 0.5 mil PET 80# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll486 0.33 10.2” 54” x 750’ 6” x 30’
AdhesiveFilm
AdhesiveSCK Liner
Contact Sales for minimums and lead time.
pg. 25
email: [email protected]. MACtac.com/technical
MACbond® Specialty
IB2711A Heat Seal Film / Acrylic PSA IB-2711Aconsistsofaheatsensitivefilmcoatedwithablueacrylic adhesive and a paper liner. It offers moderate tack and adhesion properties and high cohesive strength. It has been especially designed for the fastening and protection of lenses during the processing stages in the optical industry.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 2.0 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 2.0 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 100+ PSTC - 107
Thickness - Carrier & Adhesive .0053
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 250°F (-18° to 121°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory Liner
Blue Acrylic 1.29 mil 4.0 mil Heat Sensitive LDPE 40# SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll76 na na 59” x 108’ Custom
IB6280W50 Acrylic with Scrim Carrier A thin polymeric scrim reinforcement combined with high-tack, modified-acrylic adhesives coatings. Supplied self-wound with 80# densified, semi-bleached kraft paper liner.
The modified-acrylic, pressure-sensitive adhesive used bonds to a wide range of gasket materials, includingmostsolidandfoamedplastics.Thescrimreinforcementprovidesexcellentadhesive/composite reinforcement, dimensional stability and conformability while maintaining maximum adhesion properties. Note: IB6205, a similar product with 5.0 mil Blue HDPE liner, is also available in 50”-wide, self-wound rolls.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 4.5 4.5 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 4.5 4.5 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .006Temperature Application: Above 50°F (10°C) for best results. End Use: -40° to 302°F (-40° to 150°C)** ** MACbond IB6280 tested as free-film construction to UL 969
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerAcrylic 2.5 mil / 2.5 mil Scrim 80# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll450 0.32 11.1” 50” x 750’ 6” x 30’
AdhesiveScrim
AdhesiveSCK Liner
IB6205W50
Acrylic with Scrim Carrier A thin polymeric scrim reinforcement combined with high-tack, modified-acrylic adhesives coatings. Supplied self-wound with 5 mil Blue HDPE release liner which providesimprovedtearandmoisture/humidityresistanceoversimilarproductIB6280(80#BleachedSCK liner).
The modified-acrylic, pressure-sensitive adhesive bonds to a wide range of gasket materials, including mostsolidandfoamedplastics.Thescrimreinforcementused,providesexcellentadhesive/compositereinforcement, dimensional stability and conformability while maintaining maximum adhesion properties.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 4.5 4.5 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 4.5 4.5 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .006
Temperature Application: Above 50°F (10°C) for best results. End Use: -40° to 302°F
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerAcrylic 2.5 mil / 2.5 mil Scrim 5.0 mil Blue HDPE -
MSI Wt/MSI Roll OD Master Roll Sample Roll450 9.5” 50” x 500’ Custom
AdhesiveScrim
Adhesive
5.0 Mil HDPE Liner
4.0 MilLDPE
Adhesive
SCK Liner
Contact Sales for minimums and lead time.
pg.26
Phone: 1-800-328-2619
MACbond® Prefinished
IB1190APS A thin polyester film coated on both sides with an aggressive, general purpose, rubber based pressure sensitive adhesive. The product is supplied self-wound on a densified, semi-bleached kraft liner.
Designed for general purpose bonding applications such as in the gasket, seal, and trim markets. Typically used for bonding to foams, felts, cloths, primed wood, paper, metal, plastics, and most low or unplasticized substrates. It has an excellent balance of economy versus performance. The polyester carrier provides dimensional stability and superior die cutting properties.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 11.5 10.5 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 9.5 8.5 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .0035
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 1.8 mil / 1.2 mil 0.5 mil PET 60# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll486 0.30 9.5 54” x 750’ 6” x 30’
AdhesiveFilm
AdhesiveSCK Liner
IB1182PS A thin polyester film coated on both sides with a general purpose, rubber based pressure sensitive adhesive. The product is supplied self-wound on a 60# densified, semi-bleached kraft liner.
Designed for general purpose bonding applications such as in the gasket, seal, and trim markets. Typically used for bonding to foams, felts, cloths, primed wood, paper, metal, plastics, and most low or unplasticized substrates. It has an excellent balance of economy versus performance and can be used in many applications as an aid to assembly. The polyester carrier provides dimensional stability and superior die cutting properties.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 10.0 11.0 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 10.0 11.0 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .0034
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 1.5 mil / 1.5 mil 0.5 mil PET 60# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll486 0.30 9.5” 54” x 750’ 6” x 30’
AdhesiveFilm
AdhesiveSCK Liner
pg. 27
MACbond® Rubber, Double-coated Films, Single Liner
email: [email protected]. MACtac.com/technical
SB1786 A thin polyester film coated on both sides with a high performance acrylic based pressure sensitive adhesive. The product is supplied with two white kraft release liners for ease of handling and processing in a sheet form.
Typically used for industrial bonding applications where outstanding adhesion, high shear and good solvent resistance are required. The acrylic adhesive offers good clarity and has excellent resistance to U.V. light exposure. The polyester carrier provides excellent dimensional stability and die cutting properties.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack lbs./sq. in. - Stainless Steel 4.0 4.0 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 4.0 4.0 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .0052
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 250°F (-18° to 121°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerAcrylic 2.4 mil / 2.4 mil 0.5 mil PET 80# White SCK 80# White SCK
MSI Wt/MSI Roll OD Sheet Size Sample Sheetna 0.52 na 18” x 22”, 100/ctn 18” x 22”
SCK LinerAdhesive
FilmAdhesiveSCK Liner
Slitting Short Rolls Sheeting Pattern CoatingSize $/MSI Setup/Release Size $/MSI Setup/Release Size $/MSI Setup/Re-
lease- 10 MMSI minimum order
- $50 set-up charge
- $0.15/MSI
- $200 pattern bar charge
>6” $0.02 - Less than 750’ $0.06 $25 150+ sq inch with minimum 10” dimension
$0.15 -
>2-6” $0.06 - Less than 300’ $0.12 $25
>1-2” $0.10 $25 Less than 150’ $0.17 $25 Smaller or dutch cut sheets
$0.30 $50
5/8” - 1” $0.15 $25 Custom pallets/crates (for custom sheets greater than 800 sq inches)
$50.00/pallet
-
<5/8”(3/8”-1/2”)
The listed web width is the minimum purchase however, please note the following for these narrow rolls:60” wide web material will yield 54” of material available to ship54” wide web material will yield 48” of material available to ship50” wide web material will yield 44” of material available to shipThe additional charges will be the same as 5/8”-1” for these sizes.Shipments of material with widths less than 5/8” may be - 25% of original quantity requested.
MACbondAdditionalCharges
pg. 28
Phone:1-800-328-2619
MACfilm®
MACfilmtransferfilms – These free films are engineered to assure smooth, low-profile bonding. The moisture-resistant polycoated release liner is curl resistant and assures complete edge-to-edge bonding of laminated and die-cut parts, even in high humidity.
•Idealfornameplates,membraneswitchesassembly,moldingandtrimconstruction
•Unsupportedrubberandacrylicfreefilms
•Modifiedacrylicforhigh-tack,high-temperatureperformance
•Moisture stable release liners
•Availablein1.0milto5.0milthickness
•Bondstoawidevarietyofsubstratesincludinglow-surfaceenergymaterialssuchaspowder-coatedmetalandplastics
pg.29
MACfilm® Rubber,Double-coatedFilms,SingleLiner
email: [email protected]. MACtac.com/technical
IF1093A-80
A 2.0 mil thick film of high performance, rubber based pressure sensitive adhesive. The adhesive is protected by a two side release treated, 80# densified kraft.
Provides aggressive tack and peel adhesion along with superior shear strength. This adhesive bonds to a wide variety of materials including low energy surfaces such as polyethylene and polypropylene. The 2.0 mil adhesive thickness provides the mass needed to establish secure bonds to uneven or irregular surfaces.
An economical means of bonding fabrics, felts, foams and other materials where a reinforcing carrier membrane is not required.
Performance Test Typical Values Testing MethodQuick Tack lbs./sq. in. - Stainless Steel 11.00 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 9.0 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ PSTC - 107
Thickness inches -Adhesive Only .002Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 2.0 mil - 80# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll350 0.30 9.0” 54” x 540’ Custom
TransferFilm
SCK Liner
IF1092A
A 2.0 mil thick film of high performance, rubber based pressure sensitive adhesive. The adhesive is protected by a two side release treated, 60# densified kraft.
Provides aggressive tack and peel adhesion along with superior shear strength. This adhesive bonds to a wide variety of materials including low energy surfaces such as polyethylene and polypropylene. The 2.0 mil adhesive thickness provides the mass needed to establish secure bonds to uneven or irregular surfaces.
An economical means of bonding fabrics, felts, foams and other materials where a reinforcing carrier membrane is not required.
Performance Test Typical Values Testing MethodQuick Tack lbs./sq. in. - Stainless Steel 11.00 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 9.0 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ PSTC - 107
Thickness inches -Adhesive Only .002Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerRubber 2.0 mil - 60# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll350 0.30 9.0” 54” x 540’ Custom
TransferFilm
SCK Liner
Contact Sales for minimums and lead time.
Contact Sales for minimums and lead time.
IF2012A A 2.0 mil thick film of high performance, acrylic pressure sensitive adhesive. The adhesive is protected by a two side release treated, polycoated natural kraft liner.Provides aggressive tack and high shear strength for quick bonding and long term holding power. The acrylic adhesive has excellent ultra violet light stability and elevated temperature resistance.
The 2.0 mil thickness provides excellent adhesion to most smooth surfaces. This thin adhesive film enables nameplates and faceplates to maintain their engineered low profile appearance.
Complies with U.L. 969 “Marking and Labeling Systems” under both “indoor” and “outdoor” exposure conditions. Test conditionscanbeobtainedbycontactingMACtacorbyconsultingtheMACtacU.L.File#MH12627.
Performance Test Typical Values Testing MethodQuick Tack lbs./sq. in. - Stainless Steel 4.0 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 4.1 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ PSTC - 107
Thickness inches - Adhesive Only .002
Temperature Application: Above 50°F (10°C) for best results. End Use: -40° to 250°F (-40° to 121°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerAcrylic 2.0 mil - 83# Brown PCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll350 0.30 9.0” 54” x 540’ 6” x 30’
IF20V2 is a 2.0 mil thick film of high performance, acrylic pressure sensitive adhesive. The adhesive is protectedbya72#two-side,release-treated,bleachedpolycoatedkraftliner.
IF20V2 provides aggressive tack and high shear strength for quick bonding and long term holding power. The acrylic adhesive has excellent ultra violet light stability and elevated temperature resistance. The 2 mil thickness of IF20V2 provides excellent adhesion to most smooth surfaces. This thin adhesive film enables nameplates and faceplates to maintain their engineered low profile appearance. The adhesive utilized in IF20V2 complies with U.L. 969 “Marking and Labeling Systems” under both “indoor” and “outdoor” exposure conditions.
Performance Test Typical Values Testing MethodQuick Tack lbs./sq. in. - Stainless Steel 4.5 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 4.0 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ PSTC - 107
Thickness inches - Adhesive Only .002
Temperature Application: Above 50°F (10°C) for best results. End Use: -40° to 250°F (-40° to 121°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerAcrylic 2.0 mil na 74# White PCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll350 na na 54” x 540’ Custom
TransferFilm
Brown PCK Liner
TransferFilm
PCK Liner
IF2013A A 3.0 mil thick film of high performance, acrylic pressure sensitive adhesive. The adhesive is protected by a two side release treated, polycoated natural kraft. Provides aggressive tack and high shear strength for quick bonding and long term holding power. The acrylic adhesive has excellent ultra violet light stability and elevated temperature resistance.
3.0 mil thickness permits more complete contact area on moderately textured, irregular or mismatched surfaces. Typical uses: mounting of nameplates, faceplates, decorative trim, foams, felts, cloth, etc.
Complies with U.L. 969 “Marking and Labeling Systems” under both “indoor” and “outdoor” exposure conditions. TestconditionscanbeobtainedbycontactingMACtacorbyconsultingtheMACtacU.L.File#MH12627.
Performance Test Typical Values Testing MethodQuick Tack lbs./sq. in. - Stainless Steel 4.5 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 4.5 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ PSTC - 107
Thickness inches - Adhesive Only .003
Temperature Application: Above 50°F (10°C) for best results. End Use: -40° to 250°F (-40° to 121°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerAcrylic 3.0 mil - 83# Brown PCKSCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll350 0.34 9.5” 54” x 540’ 6” x 30’
TransferFilm
Brown PCK Liner
IF20V2
pg. 30
Phone:1-800-328-2619
MACfilm® Acrylic,FreeFilms,SingleLiner
Contact Sales for minimums and lead time.
pg.31
email: [email protected]. MACtac.com/technical
IF2015A 5.0 mil thick film of high performance, acrylic pressure sensitive adhesive. The adhesive is protected by a two side release treated, polycoated natural kraft liner.
Aggressive tack and high shear strength for quick bonding and long term holding power. The acrylic adhesive has excellent ultra violet light stability and elevated temperature resistance.
5.0 mil thickness permits more complete contact area on textured, irregular or mismatched surfaces. Typical uses: mounting of nameplates, faceplates, decorative trim, foams, felts, cloth, etc.
IF2015A complies with U.L. 969 “Marking and Labeling Systems” under both “indoor” and “outdoor” exposure conditions.TestconditionscanbeobtainedbycontactingMACtacorbyconsultingtheMACtacU.L.File#MH12627.
Performance Test Typical Values Testing MethodQuick Tack lbs./sq. in. - Stainless Steel 5.5 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 5.0 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ PSTC - 107
Thickness inches - Adhesive Only .005
Temperature Application: Above 50°F (10°C) for best results. End Use: -40° to 250°F (-40° to 121°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerAcrylic 5.0 mil - 83# Brown PCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll350 0.41 10.2” 54” x 540’ 6” x 30’
IF-2013AP2 is a 3 mil thick film of high performance, acrylic pressure sensitive adhesive. The adhesive is protected by a two side release coated polyester liner.
IF-2013AP2 provides aggressive tack and high shear strength for quick bonding and long term holding power. The acrylic adhesive has excellent ultra violet light stability and elevated temperature resistance. The 3 mil thickness of IF-2013AP2 permits more complete contact area on moderately textured, irregular or mismatched surfaces. Typical uses would include the mounting of nameplates, faceplates, decorative trim, foams, felts, cloth, etc. IF-2013AP2 complies with U.L. 969 “Marking and Labeling Systems” under both “indoor” and “outdoor” exposure conditions.
Performance Test Typical Values Testing MethodQuick Tack lbs./sq. in. - Stainless Steel 5.0 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 5.0 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ PSTC - 107
Thickness inches - Adhesive Only .003
Temperature Application: Above 50°F (10°C) for best results. End Use: -40° to 250°F (-40° to 121°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerAcrylic 3.0 mil na 2.0 mil Clear PET -
MSI Wt/MSI Roll OD Master Roll Sample Roll350 na na 54” x 540’ Custom
TransferFilm
Brown PCK Liner
TransferFilm
2.0 MilPET Liner
IF2013AP2
MACfilm® Acrylic,FreeFilms,SingleLiner
Contact Sales for minimums and lead time.
pg. 32
Phone: 1-800-328-2619
MACfilm® Acrylic,FreeFilms,SingleLiner
IF2092
TransferFilm
PCK Liner
2.0 mil thick film of high tack, modified acrylic pressure sensitive adhesive. The adhesive is protected by atwosidereleasetreated,74#polycoatedwhitekraftliner.
IF2092 provides aggressive tack and peel for quick bonding and long term adhesion. The unique acrylic adhesive bonds to a wide variety of materials with exceptional adhesion to low energy surfaces such as polypropylene and polyethylene.
2.0 mil thickness provides excellent adhesion to most smooth surfaces. The thin adhesive film enables nameplates, faceplates and other decorative attachments to maintain an engineered low profile appearance.
Performance Test Typical Values Testing MethodQuick Tack lbs./sq. in.
7.05.04.04.5
PSTC-16
Peel Adhesion, lbs./in. 7.05.55.06.5
PSTC - 101
Thickness inches - Adhesive Only .002
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 190°F (-18° to 88°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerAcrylic 2.0 mil - 74# White PCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll350 0.28 8.7” 54” x 540’ 6” x 30’
Stainless SteelHDPELDPEPP
Stainless Steel - 30 minutesHDPE - 30 minutes LDPE- 30 minutes PP - 30 minutes
IF2095
TransferFilm
PCK Liner
5.0 mil thick film of high tack, modified acrylic pressure sensitive adhesive. The adhesive is protected by atwosidereleasetreated,74#polycoatedwhitekraftliner.
Provides aggressive tack and peel for quick bonding and long term adhesion. The unique acrylic adhesive bonds to a wide variety of materials with exceptional adhesion to low energy surfaces such as polypropylene and polyethylene.
5.0 mil thickness permits more complete surface contact to textured, irregular and mismatched surfaces
Performance Test Typical Values Testing MethodQuick Tack lbs./sq. in. 11.5
7.86.07.0
PSTC-16
Peel Adhesion, lbs./in. 10.810.28.59.5
PSTC - 101
Thickness inches - Adhesive Only .005
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 200°F (-18° to 93°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerAcrylic 5.0 mil - 74# White PCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll350 0.38 9.9” 54” x 540’ 6” x 30’
Stainless SteelHDPELDPEPP
Stainless Steel - 30 minutesHDPE - 30 minutes LDPE- 30 minutes PP - 30 minutes
Slitting Short Rolls Pattern CoatingSize $/MSI Setup/Release Size $/MSI Setup/Release - 10 MMSI minimum order
- $50 set-up charge
- $0.15/MSI
- $200 pattern bar charge
>6” $0.02 - Less than 540’ $0.06 $25
>2-6” $0.06 - Less than 300’ $0.12 $25
>1-2” $0.10 $25 Less than 150’ $0.17 $25
5/8” - 1” $0.15 $25
MACfilmAdditionalCharges
pg. 33
MACfilm®
email: [email protected]. MACtac.com/technical
IF2043B IF-2043B consists of 3 mils of high-performance, acrylic adhesive and two release liners. The adhesive is protected by 60# White Polycoated Kraft release liner and 4 mil translucent-blue, LDPE film liner.
IF-2043B provides aggressive tack and high shear strength for quick bonding and long term holding power. The 3 mil acrylic adhesive has excellent ultraviolet light stability, elevated temperature resistance and provides excellent adhesion to both smooth and moderately rough surfaces. Typical uses include plate mounting, faceplates, decorative trim, gaskets, etc. The translucent-blue LDPE film release liner allows parts to be vacuum formed while maintaining the integrity of the liner and permits inspection of the laminated parts prior to final assembly.
Performance Test Typical Values Testing MethodQuick Tack lbs./sq. in. - Stainless Steel 4.5 PSTC-16
Peel Adhesion, lbs./in. Stainless Steel - 30 minutes 4.5
PSTC - 101
Shear - Hours to Fail Stainless Steel - 1000 g/sq. in. @ 72°F 300+
PSTC - 107
Thickness inches - Adhesive Only .003
Temperature Application: Above 50°F (10°C) for best results. End Use: -40° to 250°F (-40° to 121°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerAcrylic 3.0 mil na 4.0 mil Blue LDPE 60# White SCK
MSI Wt/MSI Roll OD Master Roll Sample Roll350 na na 54” x 540’ 6” x 30’
This product is a 1 mil thick film of a general purpose acrylic pressure sensitive adhesive. The adhesive is supplied between two differential release liners to allow ease of handling during the application process. The second liner is a paper adhered to a thin film to provide “tear-free” properties. IF3041 offers a means of bonding a variety of materials where a reinforcing carrier membrane is not required andtheincreasedstiffnessisnotneededordesired.CompliantwithFDA21CFR175.105ToySafetyuseperASTMF963-96a,HasbroSRS-012RevF.
Performance Test Typical Values Testing MethodQuick Tack lbs./sq. in. - Stainless Steel 3.0 PSTC-16
Peel Adhesion, lbs./in. Stainless Steel - 30 minutes 4.0
PSTC - 101
Shear - Hours to Fail Stainless Steel - 1000 g/sq. in. @ 72°F na
PSTC - 107
Thickness inches - Adhesive Only .001
Temperature Application: Above 25°F (-4°C) for best results. End Use: -75°F to 200°F (-59°C to 93°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerAcrylic 1.0 mil na Tear Free 2.5 mil SCk
MSI Wt/MSI Roll OD Master Roll Sample Roll389 na na 60” x 540’ 6” x 30’
4.0 MilBlue LDPE
Adhesive
SCK Liner
IF3041A 1.0 mil thick film of general performance, acrylic pressure sensitive adhesive. The adhesive is protected by a release treated SCK liner on each side.
Provides good tack and shear strength for immediate adhesion and long term holding power. The acrylic adhesive has excellent ultra violet light stability and elevated temperature resistance.
1.0 mil thickness provides excellent adhesion to most smooth surfaces. IF3041 offers an economical means of bonding a variety of materials where a reinforcing carrier membrane is not required and the increased stiffness is not needed or desired. Excellent choice for flexible magnets. Compliant with FDA 21CFR175.105ToySafetyuseperASTMF963-96a,HasbroSRS-012RevF.
Performance Test Typical Values Testing MethodQuick Tack lbs./sq. in. - Stainless Steel 3.0 PSTC-16
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 4.0 PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 150+ PSTC - 107
Thickness inches - Adhesive Only .001
Temperature Application: Above 50°F (10°C) for best results. End Use: -40° to 200°F (-40° to 93°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory LinerAcrylic 1.0 mil - 2.5 mil SCK 2.5 mil SCK
MSI Wt/MSI Roll OD Master Roll Sample Roll389 0.57 7.7” 60” x 540’ 6” x 30’
SCK Liner
Adhesive
SCK Liner
TransferFilm
SCK Liner
IF3041TF
Acrylic,FreeFilms,DoubleLiner
pg.34
Phone:1-800-328-2619
MACmount®
MACmountfoamtapes – These double-coated, polyethylene closed-cell foam tapes offer excellent shear strength and are highly conformable and compressible when applied to uneven, irregular or contoured surfaces. Both general purpose and high-performance rubber-based adhesives are available, as well as high-performance acrylic based adhesives.
•Idealforappliance,transportation,constructionandelectronics applications
•Widerangeofthickness,30milto125milfoamsavailable,designedforfillinggaps
•Appliedincushioning,sealing,sounddampeningand mirrormounting
pg. 35
MACmount®
email: [email protected]. MACtac.com/technical
Contact Sales for minimums and lead time.
Rubber,Double-coatedFoams,SingleLiner
IM1705A
A1/32”black,closedcellpolyethylenefoamcoatedonbothsideswithahighshearstrengthrubberbased pressure sensitive adhesive. The adhesive is protected by a two side release treated, polycoated natural kraft liner.
Generally used where the ultimate in holding power is desired for indoor applications. The aggressive adhesive bonds to most surfaces including low energy materials such as polyethylene and polypropylene. The1/32”foamcarrierprovidesagapfillingfunctionwhichaidsinthejoiningofunevenorirregularsurfaces.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack, Lbs./sq. in. Stainless Steel 7.5 9.0 MACtac CTM - 25
Peel Adhesion, lbs./in. Stainless Steel - 30 minutes
Foam Tear** PSTC - 101
Shear - Hours to Fail Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+
PSTC - 107
Thickness - Carrier & Adhesive .036
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory Liner
Rubber/Rubber 2.7 mil / 2.7 mil 1/32” Black PE Foam 83# Brown PCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll
140 0.52 12.4” 54” x 216’ Custom
AdhesiveBlack Foam
AdhesivePCK Liner
IM1800A A1/32”white,closedcellpolyethylenefoamcoatedonbothsideswithahighshearstrengthrubberbased pressure sensitive adhesive. The adhesive is protected by a two side release treated, polycoated natural kraft liner.
Generally used where the ultimate in holding power is desired for indoor applications. The aggressive adhesive bonds to most surfaces including low energy materials such as polyethylene and polypropylene. The1/32”foamcarrierprovidesagapfillingfunctionthataidsinthejoiningofunevenorirregularsurfaces.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack, Lbs./sq. in. Stainless Steel 7.5 9.0 MACtac CTM - 25
Peel Adhesion, lbs./in.Stainless Steel - 1 minute Stainless Steel - 30 minutes Foam Tear**
PSTC - 101
Shear - Hours to Fail Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+
PSTC - 107
Thickness - Carrier & Adhesive .036
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory Liner
Rubber/Rubber 2.7 mil / 2.7 mil 1/32” White PE Foam 83# Brown PCk -
MSI Wt/MSI Roll OD Master Roll Sample Roll
140 0.50 12.4” 54” x 216’ 6” x 20’
AdhesiveFoam
AdhesivePCK Liner
IM1801A A1/32”white,closedcellpolyethylenefoamcoatedonbothsideswithahighshearstrengthrubberbased pressure sensitive adhesive. The adhesive is protected by a two side release treated, semi-bleached kraft liner.
Generally used where the ultimate in holding power is desired for indoor applications. The aggressive adhesive bonds to most surfaces including low energy materials such as polyethylene and polypropylene. The1/32”foamcarrierprovidesagapfillingfunctionthataidsinthejoiningofunevenorirregularsurfaces.
Performance TestTypical Values
Testing MethodUnwind Liner
Quick Tack, Lbs./sq. in. Stainless Steel 6.5 8.5 MACtac CTM - 25
Peel Adhesion, lbs./in. Stainless Steel - 30 minutes
Foam Tear** PSTC - 101
Shear - Hours to Fail Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+
PSTC - 107
Thickness - Carrier & Adhesive .036
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory Liner
Rubber/Rubber 2.7 mil / 2.7 mil 1/32” White PE Foam 60# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll140 0.45 12.0” 54” x 216’ na
** Typically, the adhesion exceeds the strength of the foam in the range of 6 - 9 Lbs./ inch
AdhesiveFoam
AdhesiveSCK Liner
pg.36
Phone: 1-800-328-2619
MACmount® Rubber,Double-coatedFoams,SingleLiner
IM1900A A1/32”white,closedcellpolyethylenefoamcoatedonbothsideswithanaggressive,generalpurpose,rubber based pressure sensitive adhesive. The product is supplied self-wound on a densified, semi-bleached kraft release liner.
Developed for general purpose bonding applications. The adhesive bonds to most surfaces including lowenergymaterialssuchaspolyethyleneandpolypropylene.The1/32”foamcarrierprovidesagapfillingfunctionthataidsinthejoiningofunevenorirregularsurfaces.
Performance TestTypical Values
Testing MethodUnwind Liner
Peel Adhesion, lbs./in. Stainless Steel - 1 minute Stainless Steel - 30 minutes
Foam Tear**PSTC - 101
Shear - Hours to Fail Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+
PSTC - 107
Thickness - Carrier & Adhesive .034
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 150°F (-18° to 66°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory Liner
Rubber/Rubber 1.8 mil / 1.8 mil 1/32” White PE Foam 80# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll
140 0.35 11.9” 54” x 216’ 6” x 20’
AdhesiveFoam
AdhesiveSCK Liner
IM1810A A1/16”white,closedcellpolyethylenefoamcoatedonbothsideswithahighshearstrengthrubberbased pressure sensitive adhesive. The adhesive is protected by a two side release treated, polycoated natural kraft liner.
Generally used where the ultimate in holding power is desired for indoor applications. The aggressive adhesive bonds to most surfaces including low energy materials such as polyethylene and polypropylene. The1/16”foamcarrierprovidesagapfillingfunctionthataidsinthejoiningofunevenorirregularsurfaces.
Performance TestTypical Values
Testing MethodUnwind Liner
Peel Adhesion, lbs./in. Stainless Steel - 1 minute Stainless Steel - 30 minutes
Foam Tear**PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .066
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 150°F (-18° to 66°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory Liner
Rubber/Rubber 2.7 mil / 2.7 mil 1/16” White PE Foam 83# Brown PCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll
70 0.60 11.6” 54” x 108’ 6” x 20’
AdhesiveFoam
AdhesivePCK Liner
IM1830A A1/16”white,closedcellpolyethylenefoamcoatedonbothsideswithahighshearstrengthrubberbased pressure sensitive adhesive. The adhesive is protected by an 80# two side release treated, semi-bleached kraft liner.
Generally used where the ultimate in holding power is desired for indoor applications. The aggressive adhesive bonds to most surfaces including low energy materials such as polyethylene and polypropylene. The1/16”foamcarrierprovidesagapfillingfunctionthataidsinthejoiningofunevenorirregularsurfaces.
Performance TestTypical Values
Testing MethodUnwind Liner
Peel Adhesion, lbs./in. Stainless Steel - 1 minute Stainless Steel - 30 minutes
Foam Tear**PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness - Carrier & Adhesive .066
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 150°F (-18° to 66°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory Liner
Rubber/Rubber 2.7 mil / 2.7 mil 1/16” White PE Foam 80# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll
70 0.60 11.6” 54” x 108’ 6” x 20’** Typically, the adhesion exceeds the strength of the foam in the range of 6 - 9 Lbs./ inch
AdhesiveFoam
AdhesiveSCK Liner
pg. 37
MACmount®
email: [email protected]. MACtac.com/technical
Rubber,Double-coatedFoams,SingleLiner
IM1930A A1/16”white,closedcellpolyethylenefoamcoatedonbothsideswithanaggressive,generalpurpose,rubber based pressure sensitive adhesive. The product is supplied self-wound on a densified, semi-bleached kraft release liner.
Developed for general purpose bonding applications. The adhesive bonds to most surfaces including lowenergymaterialssuchaspolyethyleneandpolypropylene.The1/16”foamcarrierprovidesagapfillingfunctionthataidsinthejoiningofunevenorirregularsurfaces.
Performance TestTypical Values
Testing MethodUnwind Liner
Peel Adhesion, lbs./in. Stainless Steel - 1 minute Stainless Steel - 30 minutes
Foam Tear**PSTC - 101
Shear - Hours to Fail Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+
PSTC - 107
Thickness - Carrier & Adhesive .066
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 150°F (-18° to 66°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory Liner
Rubber/Rubber 1.8 mil / 1.8 mil 1/16” White PE Foam 80# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll
70 0.45 11.3” 54” x 108’ 6” x 20’
AdhesiveFoam
AdhesiveSCK Liner
IM1940A A1/8”white,closedcellpolyethylenefoamcoatedonbothsideswithanaggressive,generalpurpose,rubber based pressure sensitive adhesive. The product is supplied self-wound on a densified, semi-bleached kraft release liner.
Developed for general purpose bonding applications. The adhesive bonds to most surfaces including lowenergymaterialssuchaspolyethyleneandpolypropylene.The1/8”foamcarrierprovidesagapfillingfunctionthataidsinthejoiningofunevenorirregularsurfaces.
Performance TestTypical Values
Testing MethodUnwind Liner
Peel Adhesion, lbs./in. Stainless Steel - 1 minute Stainless Steel - 30 minutes
Foam Tear**PSTC - 101
Shear - Hours to Fail Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+
PSTC - 107
Thickness - Carrier & Adhesive .129
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 150°F (-18° to 66°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory Liner
Rubber/Rubber 1.8 mil / 1.8 mil 1/8” White PE Foam 80# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll
70 0.65 15.2” 54” x 108’ 6” x 20’
** Typically, the adhesion exceeds the strength of the foam in the range of 6 - 9 Lbs./ inch
AdhesiveFoam
AdhesiveSCK Liner
pg. 38
Phone: 1-800-328-2619
MACmount® Rubber, Double-coated Films, Single LinerAcrylic,Double-coatedFoams,SingleLinerMACmount®
A1/32”black,closedcellpolyethylenefoamcoatedonbothsideswithahighperformance,modifiedacrylic pressure sensitive adhesive. The adhesive is protected by a blue 5.0 mil HDPE liner.
Provides the excellent temperature properties, holding power and chemical resistance exhibited by acrylicadhesivesplusthestrengthofacross-linkedpolyethylenefoam.The1/32”foamcarrieroffersagapfillingfunctionthataidsinthejoiningofunevenorirregularsurfaces.TheHDPElinerismoistureresistant and provides very good tear resistance.
Performance TestTypical Values
Testing MethodUnwind Liner
Peel Adhesion, lbs./in. Stainless Steel - 30 minutes 6.0 5.0
PSTC - 101
Shear - Hours to Fail Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+
PSTC - 107
Thickness - Carrier & Adhesive .036
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 200°F (-18° to 90°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory Liner
Acrylic/Acrylic 2.0 mil / 2.0 mil 1/32” White PE Foam 5.0 mil Blue HDPE -
MSI Wt/MSI Roll OD Master Roll Sample Roll
132 0.39 12.1” 51” x 216’ Custom
A1/32”black,closedcellpolyethylenefoamcoatedonbothsideswithahighperformance,modifiedacrylic pressure sensitive adhesive. The adhesive is protected by a blue 5.0 mil HDPE liner.
Provides the excellent temperature properties, holding power and chemical resistance exhibited by acrylicadhesivesplusthestrengthofacross-linkedpolyethylenefoam.The1/32”foamcarrieroffersagapfillingfunctionthataidsinthejoiningofunevenorirregularsurfaces.TheHDPElinerismoistureresistant and provides very good tear resistance.
Performance TestTypical Values
Testing MethodUnwind Liner
Peel Adhesion, lbs./in. Stainless Steel - 30 minutes 4.5 5.0
PSTC - 101
Shear - Hours to Fail Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+
PSTC - 107
Thickness - Carrier & Adhesive .026
Temperature Application: Above 50°F (10°C) for best results. End Use: -20° to 200°F (-29° to 90°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory Liner
Modified Acrylic 2.2 mil / 2.2 mil 20 mil Black PE Foam 80# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll
140 na na 54” x 216’ Custom
IM2908N
AdhesiveBlack Foam
Adhesive
5.0 MilHDPE Liner
A1/32”black,closedcellpolyethylenefoamcoatedonbothsideswithamodified-acrylicpressuresensitive adhesive. The adhesive is protected by a 80# densified, semi-bleached kraft release liner.
Provides the excellent temperature properties, holding power and chemical resistance exhibited by acrylicadhesivesplusthestrengthofacross-linkedpolyethylenefoam.The1/32”foamcarrieroffersagap-fillingfunctionwhichaidsinthejoiningofunevenorirregularsurfaces.
Performance TestTypical Values
Testing MethodUnwind Liner
Peel Adhesion, lbs./in. Stainless Steel - 30 minutes 6.0 5.0
PSTC - 101
Shear - Hours to Fail Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+
PSTC - 107
Thickness - Carrier & Adhesive .036
Temperature Application: Above 50°F (10°C) for best results. End Use: -20° to 200°F (-29° to 90°C)
Adhesive Field/Factory Thickness Carrier Field Liner Factory Liner
Acrylic/Acrylic 2.0 mil/ 2.0 mil 1/32” Black PE Foam 80# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll
140 0.39 12.1” 54” x 216’ Custom
IM2908-80
AdhesiveBlack Foam
AdhesiveSCK Liner
AdhesiveBlack Foam
AdhesiveSCK Liner
IM2901
Contact Sales for minimums and lead time.
Contact Sales for minimums and lead time.
Contact Sales for minimums and lead time.
pg.39
MACmount®
email: [email protected]. MACtac.com/technical
MACmountAdditionalChargesSlitting Short Rolls Pattern CoatingSize $/MSI Setup/Release Size $/MSI Setup/Release - 10 MMSI minimum order
- $50 set-up charge
- $0.15/MSI
- $200 pattern bar charge
>6” $0.05 - Less than 750’ $0.06 $25
>2-6” $0.10 - Less than 300’ $0.12 $25
>1-2” $0.15 $50 Less than 150’ $0.17 $25
5/8” - 1” $0.20 $50
<5/8”(3/8”-1/2”)
The listed web width is the minimum purchase however, please note the following for these narrow rolls:54” wide web material will yield 51” of material available to ship51” wide web material will yield 48” of material available to shipThe additional charges will be the same as 5/8”-1” for these sizes.Shipments of material with widths less than 5/8” may be - 25% of original quantity requested.
A1/32”white,closedcellpolyethylenefoamcoatedonbothsideswithahighperformance,modifiedacrylic pressure sensitive adhesive. The adhesive is protected by a 60# densified, semi-bleached kraft release liner.
Provides the excellent temperature properties, holding power and chemical resistance exhibited by acrylicadhesivesplusthestrengthofacross-linkedpolyethylenefoam.The1/32”foamcarrieroffersagapfillingfunctionthataidsinthejoiningofunevenorirregularsurfaces.
Performance TestTypical Values
Testing MethodUnwind Liner
Peel Adhesion, lbs./in. Stainless Steel - 1 minute Stainless Steel - 30 minutesStainless Steel - 24 hours
5.56.58.5
4.56.08.0
PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+ PSTC - 107
Thickness inches - Adhesive Only .036
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 200°F (-18° to 90°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory Liner
Acrylic/Acrylic 2.0 mil / 2.0 mil 1/32” White PE Foam 60# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll
140 0.34 11.8” 54” x 216’ 6” x 20’
IM2920
AdhesiveFoam
AdhesiveSCK Liner
A1/16”white,closedcellpolyethylenefoamcoatedonbothsideswithahighperformance,modifiedacrylic pressure sensitive adhesive. The adhesive is protected by a 60# densified, semi-bleached kraft release liner.
Provides the excellent temperature properties, holding power and chemical resistance exhibited by acrylic adhesives plus the strength of a cross-linked polyethylene foam.The 1/16” foam carrier offers agapfilling function that aids in the joining of uneven or irregular surfaces.
Performance TestTypical Values
Testing MethodUnwind Liner
Peel Adhesion, lbs./in. Stainless Steel - 1 minute Stainless Steel - 30 minutesStainless Steel - 24 hours
6.5^7.5^8.5^
6.0^6.5^8.0^
PSTC - 101
Shear - Hours to Fail Stainless Steel - 1000 g/sq. in. @ 72°F 300+ 300+
PSTC - 107
Thickness - Carrier & Adhesive .066
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 200°F (-18° to 90°C)
Adhesive Unwind/Liner Thickness Carrier Field Liner Factory Liner
Acrylic/Acrylic 2.0 mil / 2.0 mil 1/16” White PE Foam 60# White SCK -
MSI Wt/MSI Roll OD Master Roll Sample Roll
70 0.44 11.3” 54” x 108’ 6” x 20’^ Partial foam tear. Typically, the adhesion exceeds the strength of the foam.
IM2940
AdhesiveFoam
AdhesiveSCK Liner
Acrylic,Double-coatedFoams,SingleLiner
pg.40
Phone:1-800-328-2619
GS SeriesGSSeriesAdhesives – Specially formulated to provide instant, very aggressive tack and peel adhesion as well as superior shear strength, GS Series high-strength adhesive tape is durable enough to replace many mechanical fasteners. Ideal for permanent bonding of substrates in the assembly and manufacturing industries.
•Idealforpackaging,transportation,constructionand P.O.P applications
•Availablein5.0milto50milthickness
•Availablein1/2”to11-1/2”adhesivewidths
•Usedinvibrationdampeningandpackagingassemblies
•Speedsassemblyandlowersmanufacturingcosts
•Fills gaps
•Actsasamoisturebarrier
pg.41
GS Series
email: [email protected]. MACtac.com/technical
High-StrengthAdhesiveTapes
TheGS-SeriesofstripadhesivesaremadeupofanunsupportedSBRpressuresensitiveadhesive,specially coated by MACtac using a patented, proprietary process, and wound on a 60# densified kraft release liner.
The adhesive used in the GS-Series provides very aggressive tack and peel adhesion along with superior shear strength. This adhesive bonds to a wide variety of materials including low energy surfaces such as polyethylene and polypropylene. The standard thicknesses of 5 to 50 mils provides the mass needed to establish secure bonds to uneven or irregular surfaces.
TheGS-Seriesstripadhesivesareavailableinanumberofnarrowwidthsizesrangingfrom1/4”to111/2”.Thetoleranceforanygivenwidthis+/-1/16”.Typicallyprovidedasasingleordoublestripofadhesive on the 60# liner, each roll has ungummed edges for ease of handling and quick liner removal. There are manufacturing limitations, however, so please contact your district sales manager to review your application in order to determine suitability.
TheGSSeriesisalsoavailablewitha2milpolyesterlinerasacustomconstruction.
*Customandmade-to-ordersizesareavailable,contactsalesorcustomerservice.
GS2004 5.0 mil version of high peel and tack adhesive free film for difficult to adhere to substrates; bonding and mounting to irregular surfaces; semi-structural bonding; good for assembly.
Performance Test Typical Values Testing MethodQuick Tack, Lbs./sq. in. - Stainless Steel 20+
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 22+ PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ PSTC - 107
Thickness inches - Adhesive Only .005
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)
Adhesive Field/Factory Ct Wt Carrier Field Liner Adh. Width/Liner Width
Rubber 5.0 mil - 60# White SCK 1.00” / 1.50”
MSI Wt/MSI Roll OD Master Roll Sample Roll16.2 0.28 11.4” 5.0 mil x 1.5” x 900’ 5.0 mil x 1.5” x 50’
TransferFilm
SCK Liner
GS1003 20.0 mil version of high peel and tack adhesive free film for difficult to adhere substrates; bonding and mounting to irregular surfaces; semi-structural bonding; good for assembly
Performance Test Typical Values Testing MethodQuick Tack, Lbs./sq. in. - Stainless Steel 20+
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 22+ PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ PSTC - 107
Thickness inches - Adhesive Only .020
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)
Adhesive Field/Factory Ct Wt Carrier Field Liner Adh. Width/Liner Width
Rubber 20 mil - 60# White SCK 0.50” / 1.00”
MSI Wt/MSI Roll OD Master Roll Sample Roll2.4 0.84 9.5” 20.0 mil x 1.0” x 200’ 20.0 mil x 1.0” x 50’
TransferFilm
SCK Liner
pg.42
Phone:1-800-328-2619
GS SeriesGS1001 20.0 mil version of high peel and tack adhesive free film for difficult to adhere substrates; bonding and
mounting to irregular surfaces; semi-structural bonding; good for assembly.
Performance Test Typical Values Testing MethodQuick Tack, Lbs./sq. in. - Stainless Steel 20+
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 22+ PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ PSTC - 107
Thickness inches - Adhesive Only .020
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)
Adhesive Field/Factory Ct Wt Carrier Field Liner Adh. Width/Liner Width
Rubber 20 mil - 60# White SCK 1.00” / 1.50”
MSI Wt/MSI Roll OD Master Roll Sample Roll3.6 0.84 9.5” 20.0 mil x 1.5” x 200’ 20.0 mil x 1.0” x 50’
GS1013 20.0 mil version of high peel and tack adhesive free film for difficult to adhere substrates; bonding and mounting to irregular surfaces; semi-structural bonding; good for assembly
Performance Test Typical Values Testing MethodQuick Tack, Lbs./sq. in. - Stainless Steel 20+
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 22+ PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ PSTC - 107
Thickness inches - Adhesive Only .020
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)
Adhesive Field/Factory Ct Wt Carrier Field Liner Adh. Width/Liner Width
Rubber 20 mil - 60# White SCK 2.00” / 3.00”
MSI Wt/MSI Roll OD Master Roll Sample Roll7.2 0.84 9.5” 20.0 mil x 3.0” x 200’ 20.0 mil x 1.0” x 50’
GS1039 30.0 mil version of high peel and tack adhesive free film for difficult to adhere substrates; bonding and mounting to irregular surfaces; semi-structural bonding; good for assemblyPerformance Test Typical Values Testing Method
Quick Tack, Lbs./sq. in. - Stainless Steel 20+
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 22+ PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ PSTC - 107
Thickness inches - Adhesive Only .030
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)
Adhesive Field/Factory Ct Wt Carrier Field Liner Adh. Width/Liner Width
Rubber 30 mil - 60# White SCK 0.63” / 1.00”
MSI Wt/MSI Roll OD Master Roll Sample Roll
30.0 mil x 1.0” x 500’ 30.0 mil x 1.0” x 50’
TransferFilm
SCK Liner
TransferFilm
SCK Liner
TransferFilm
SCK Liner
GS1019 35.0 mil version of high peel and tack adhesive free film for difficult to adhere substrates; bonding and mounting to irregular surfaces; semi-structural bonding; good for assemblyPerformance Test Typical Values Testing Method
Quick Tack, Lbs./sq. in. - Stainless Steel 20+
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 22+ PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ PSTC - 107
Thickness inches - Adhesive Only .035
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)
Adhesive Field/Factory Ct Wt Carrier Field Liner Adh. Width/Liner Width
Rubber 35 mil - 60# White SCK 0.75” / 1.50”
MSI Wt/MSI Roll OD Master Roll Sample Roll3.6 1.40 11.4” 35.0 mil x 1.5” x 200’ 35.0 mil x 1.0” x 50’
TransferFilm
SCK Liner
pg.43
GS Series
email: [email protected]. MACtac.com/technical
High-StrengthAdhesiveTapes
GS1007 35.0 mil version of high peel and tack adhesive free film for difficult to adhere substrates; bonding and mounting to irregular surfaces; semi-structural bonding; good for assembly Performance Test Typical Values Testing Method
Quick Tack, Lbs./sq. in. - Stainless Steel 20+
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 22+ PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ PSTC - 107
Thickness inches - Adhesive Only .035
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)
Adhesive Field/Factory Ct Wt Carrier Field Liner Adh. Width/Liner Width
Rubber 35 mil - 60# White SCK 1.00” / 1.50”
MSI Wt/MSI Roll OD Master Roll Sample Roll3.6 1.40 11.4” 35.0 mil x 1.5” x 200’ 35.0 mil x 1.0” x 50’
GS2906 50.0 mil version of high peel and tack adhesive free film for difficult to adhere substrates; bonding and mounting to irregular surfaces; semi-structural bonding; good for assemblyPerformance Test Typical Values Testing Method
Quick Tack, Lbs./sq. in. - Stainless Steel 20+
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 22+ PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ PSTC - 107
Thickness inches - Adhesive Only .050
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)
Adhesive Field/Factory Ct Wt Carrier Field Liner Adh. Width/Liner Width
Rubber 50 mil - 60# White SCK 2.00” / 2.40”
MSI Wt/MSI Roll OD Master Roll Sample Roll7.2 1.97 11.6” 50.0 mil x 2.5” x 200’ na
GS1004 35.0 mil version of high peel and tack adhesive free film for difficult to adhere substrates; bonding and mounting to irregular surfaces; semi-structural bonding; good for assemblyPerformance Test Typical Values Testing Method
Quick Tack, Lbs./sq. in. - Stainless Steel 20+
Peel Adhesion, lbs./in. - Stainless Steel - 30 minutes 22+ PSTC - 101
Shear - Hours to Fail - Stainless Steel - 1000 g/sq. in. @ 72°F 300+ PSTC - 107
Thickness inches - Adhesive Only .035
Temperature Application: Above 50°F (10°C) for best results. End Use: 0° to 180°F (-18° to 82°C)
Adhesive Field/Factory Ct Wt Carrier Field Liner Adh. Width/Liner Width
Rubber 35 mil - 60# White SCK 0.50” / 2.00”
MSI Wt/MSI Roll OD Master Roll Sample Roll4.8 1.40 11.4” 35.0 mil x 2.0” x 200’ 35.0 mil x 1.0” x 50’
TransferFilm
SCK Liner
TransferFilm
SCK Liner
TransferFilm
SCK Liner
pg.44
Phone:1-800-328-2619
pg.44
PhenolicTapes The MACtac® IF4020 Series was developed for bonding friction materials with fewer environmental and safety issues than solvent-based adhesives, MACtac has developed a series of heat-activated, dry film adhesive products. MACtac’s dry film nitrile-phenolic tapes provide permanent adhesion to a variety of wet-laid fibers (paper), carbon and other friction materials utilized in automotive OEM, aerospace, heavy equipment, lawn and garden, and industrial applications.
The new series addresses solvent-evaporation and adhesive quantity issues common with liquid adhesives. It also reduces waste and improves overall manufacturing efficiency by allowing pre-measured tapes to be pre-applied in-line to raw materials or converted parts usingmodestheat-assistlamination(approx.66°C/150°F).Thefinalbond of the adhesive-coated friction material to its companion is completed at a higher temperature and pressure. This allows for greater speed-to-market when compared to parts manufactured with liquid adhesives, which can take up to a day to cure.
The series demonstrates high strength properties at low and elevated temperatures and excellent chemical resistance. This combination is critical for friction applications where parts are subjectedtohighoperatingtemperatures,energyabsorptionandpressures, as well as exposure to chemicals such as transmission and brake fluids.
•Permanentadhesionwherepartsareexposedtochemicalssuchastransmissionfluids.
•Idealforhigh-temperatureresistanceapplications
•Highperformanceapplications
pg.45
email: [email protected]. MACtac.com/technical
NitrilPhenolicFilmedAdhesivePhenolicTapesIF4020A
IF4023A A 2.2 mil thick dry film of thermosetting adhesive. It is protected by a 84# polycoated kraft liner, release coated on two sides.
The adhesive can typically be transferred from the protective release liner to the bondable substrate withtheuseofmodestheat(approx.150°F).Theselectedcurescheduleshouldthenbeperformedto obtain full bond to the end use substrate.
When properly cured, IF-4023A exhibits good strength properties at both low and elevated temperatures.Italsoexhibitsexcellentplasticflowwhichcontributestowardobtaining100%contactwith the substrates to be bonded. The material becomes thermoset after cure.
Performance Test Typical Values Testing MethodDisc Shear Strength psi 73°F 400°F
2500+500+
SAE J840
Curing ConditionsThe desired disc shear strength can be obtained with any of the following “Bond-Line” temperatures and times:. A. 350° F for 15 minutes B. 370° F for 10 minutes C. 400° F for 5 minutes
Ct Wt Field Liner Factory Liner
2.2 mil 84# White PCK na
Roll OD Master Roll Sample
13.8” 60” x 1,800’ 8” x 10” Sheets
Dry Film
SCK Liner
Dry Film
PCK Liner
A 1.0 mil thick dry film of thermosetting adhesive. It is protected by a 60# densified kraft liner, release coated on both sides.
The adhesive can typically be transferred from the protective release liner to the bondable substrate withtheuseofmodestheat(approx.150°F).Theselectedcurescheduleshouldthenbeperformedto obtain the full bond to the end use substrate.
When properly cured, IF-4020A exhibits good strength properties at both low and elevated temperatures.Italsoexhibitsexcellentplasticflowwhichcontributestowardobtaining100%contactwith the substrates to be bonded. The material becomes thermoset after cure.
Performance Test Typical Values Testing MethodDisc Shear Strength psi 73°F 400°F
2500+500+
SAE J840
Curing ConditionsThe desired disc shear strength can be obtained with any of the following “Bond-Line” temperatures and times:. A. 350° F for 15 minutes B. 370° F for 10 minutes C. 400° F for 5 minutes
Ct Wt Field Liner Factory Liner
1..0 mil 60# White SCK na
Roll OD Master Roll Sample
11.2” 56” x 1,800’ 8” x 10” Sheets
pg.46
Phone: 1-800-328-2619
Safety GritA permanent, conformable PSA product that provides a safe, non-slip surface.
•Finelyground,siliconcarbidegrit,uniforminsizeand evenly distributed.
•Water-resistantgritallowsforexposuretoharsh interiorandexteriorenvironments.
•Industrialstrengthfilmcarrierpreventsrot,offershighmoistureresistanceandinsuresstability.
•Wet/drycarrierresiststearing,chippingandflaking.
•Highquality,hightackrubber-basedadhesiveadheres to a wide variety of substrates including painted and unpaintedwood,metalandetchedconcrete.
•Adhesiveresistswater,alcoholsanddetergent.
pg.47
email: [email protected]. MACtac.com/technical
Safety Grit
IC6187
Consists of a finely ground mineral abrasive permanently bonded to one side of a high-strength, non-tearing plastic carrier film with an adhesive on the opposite side. The permanent pressure sensitive adhesive is protected with a kraft paper release liner.
Providesalowprofile,non-slipmaterialforinterior/exteriorsurfacessuchasshopfloors,stairs, loading ramps, ladders, recreational vehicles, diving boards, skateboards, etc. The adhesive provides instant secure bonding with no lifting even in high-traffic areas.
Performance Test Typical Values Testing MethodShear - Hours to Fail Stainless Steel - 1000 g/sq. in. @ 72°F
100+ PSTC-7
Peel Adhesion, lbs./in. Stainless Steel - 30 minutes 5.0 PSTC-1
Thickness inches - Film plus adhesive .020
Temperature Application: Above 50°F (10°C) for best results. End Use: 20° to 150°F (-7° to 66°C)
Adhesive Field/Factory Ct Wt Carrier Field Liner Factory Liner
Rubber 2.1 Plastic 80# White CCK -
MSI Wt/MSI Roll OD Master Roll Sample Sheet
162 0.81 11” 54” x 250’ Custom
GritPlastic
AdhesiveCCK Liner
SafetyGritAdditionalChargesSlitting Short RollsSize $/MSI Setup/Release Size $/MSI Setup/Release
>6” $0.05 - Any Short Roll $0.20 $50
>2-6” $0.10 $75
>1-2” $0.15 $75
Contact Sales for minimums and lead time.
pg.48
Phone: 1-800-328-2619
Specialty Products Rubber, Double-coated Films, Single LinerBuilding&ConstructionApplication IdeasFrom the inside to the outside, MACtac® has adhesive products perfectly suited for the building and construction markets. Products in this area include cold application temp HVAC tapes as well as PSA for Window and Door sealing and mounting. For high performance and high value, look to MACtac for Building and Construction needs.
Products mentioned below are proven effective for the associated applications, but by no means represent the entirety of MACtac’s product offering. Our Sales and Technical Marketing teams are ready to provide specific product recommendations.
Application Product Substrates Product Benefit
PipeInsulation(HVAC) Building Products
Bonding to common insulation facings (Foil, ASJ & FSK)
With a variety of Faces such as Foil, ASJ, Soft White Vinyl and Scrim, MACtac BuildingProducts meet a wide range of performance criteria for HVAC applications.
WindowsandDoorsSealing
IB119XAIB213X
Bonding various solid or foamed seals to glass, metal, wood & PVC
Whether replacement wndows or new construction, MACtac has products for sealing IG units, setting replacements, and a wide variety of gasket and protection materials. IB119XA bonds well to plastics and provides for vibration and acoustical noise reduction. IB213X provides higher temperature performance and UV resistance.
Roofing,FaçadeInsulation
GS-Series Bonding various plastic or rubber seals to metal, wood & PVC
GS-Seriesthick mass of adhesive from 5 to 50mils provides a very aggressive bond for high shear applications. GS-Series allows for elimination of rivets and mechanical fasteners, and acts as a seals substrates from moisture
Acoustic Insulation IB1188 Bonding sound & vibration-damping materials to metals, wood & plastics
Bonds well to foams, with the shear strength needed for permanent wall mounting, IB1188 is used in a number of noise and vibration dampening applications inside and outside of the home.
Bumpers Specialty Bumper Films
Bonding cast urethane bumpers to metal, plastic, wood & glass
MACtacusesspecialtyfilmsinconjunctionwithstandard,highperformance rubber and acrylic adhesives to provide the right properties for Bumpers going into cabinets, electronics and more.
General Purpose MountingandBonding
IM18XXA Similar & dissimilar metals, plastics &natural/syntheticfibers
For high shear wall mounting, IM18XXA acts as a gap filler with excellent adhesion.
CarpetMounting,FloorInstallation
IB1178AIB6280
GS-Series
Bonding similar & dissimilar materials including wood, plastic, metal & carpeting
IB1178A provides stability to various commercial landing tiles, while the scrim carrier and environmental resistance of IB6280 works well around corners with initial repositionability. For wood, PVC & carpet trim pieces, GS-Series products provide both aggressive adhesion and excellent cohesive strength.
SecurityWindowFilms Specialty Window
Bonding to glass, polycarbonate & other transparent substrates
In addition to adding cosmetic appearance to glass used in furniture, window and cabinet doors, MACtacWindowFilmsoffer a unique safety feature.
SettingBlocks IF1092A Bonding various rubber materals to other window components
Thin profile, economic with excellent performance, IF1092A 2.0 mil rubber free-film provides necessary support for durable setting blocks.
pg.49
Specialty Products Rubber, Double-coated Films, Single Liner
email: [email protected]. MACtac.com/technical
Appliance ApplicationsApplication IdeasAppliance applications present unique challenges for which MACtac® has a variety of standard and custom solutions. From UL Listed Acrylic products that bond well to high and low surface energy surfaces to economical rubber adhesives, MACtac has partnered with Appliance OEM’s and suppliers for many years to change how PSA’s fit into their process.
Products mentioned below are proven effective for the associated applications, but by no means represent the entirety of MACtac’s product offering. Our Sales and Technical Marketing teams are ready to provide specific product recommendations.
Application Product Substrates Product Benefit
SoundDampening IB1175AERGS-Series
Sound & vibration-damping foams to metals & plastics.
IB1175AER has excellent wetting properties for challenging substrates such as porous foams, and an easy-release liner for problem-free dispensing of die-cut, soft-foam gaskets.
InsulationBonding IM18XXAIM29XX
Bonding plastic-encapsulated insu-lation to metals & plastics
Availableincombinationsof1/32”,1/16”,and1/8”withblackand white foams, the IM18XXA has excellent shear and heat resistance for a rubber adhesive, while IM29XX products provides acrylic performance.
Gasket and Seal Mounting
IB119XA Bonding gasket materials including foams to metals & plastics
IB119XA is a high performing workhorse rubber adhesive ideal for a wide variety of applications. A softer adhesive bonds well to challenging surfaces, while the heavier factory-side coat weight flows into porous substrates.
Nameplate&GraphicOverlays
IF201XAIF209X
Plastic or metal to variety of plas-tics & powder-coated paints.
Thin profile acrylic free-films, IF201XA provides good adhesion and environmental resistance to standard surfaces, while IF209X handles the challenges of lower surface energy materials like powder coated paints and plastics.
FoamMounting IM18XXAIM19XXA
Bonding unpainted metals to painted metals & various plastics
IM18XXA offers a higher performance product for difficult applications. IM18XXA uses a heavier coat weight rubber adhesive with better shear and temperature resistance than IM19XXA. Both IM18XXA and IM19XXA are available in 1/32”,1/16”and1/8”whiteandblackPEfoam.
ScrewAnchors IM18XXAIM19XXA
Bonding unpainted metals to painted metals & various plastics
IM19XXA offers greater value than IM18XXA where general performance is required. Additionally, as a softer adhesive, it may succeed where other rubber adhesives fail. Both IM18XXAandIM19XXAareavailablein1/32”,1/16”and1/8”white and black PE foam.
DecorativeTrimBonding
IF201XAIF209X
IB119XA
Bonding trim to various paints. LSE plastics & powder-coats.
IF201XA acrylic freefilms provide excellent adhesion and environmental resistance to high surface energy substrates, while IF209X handles low surface energies. IB119XA has a variety of widths and liners for applications that do not require the environmental and heat resistance of an acrylic.
Door HandleBonding GS-Series Bondingpainted/platedmetalsorplastic parts to various paints.
GS-Series thick mass of adhesive from 5 to 50mils provides a very aggressive bond for high shear applications. GS-Series allows for elimination of rivets and mechanical fasteners, and acts as a seals substrates from moisture.
ProtectiveDoorLiners Optically Clear Glass & polycarbonate windows; painted metal surfaces
MACtac has a variety of Optically Clear adhesives and overlaminates originally developed for photo lamination.
PSALabelStock Label Products Painted metals, plastics & glass For more information about a large variety of PrintableLabelProducts,contactyourMACtacSalesRepresentative.
pg. 50
Phone: 1-800-328-2619
Specialty Products Rubber, Double-coated Films, Single LinerRV&MarineApplicationsApplication IdeasMarine&RVpresentchallengesduetotheharshenvironment.Reducingnoise,adhering through shock and vibration, heat and chemicals, MACtac® has developed and specified a variety of products with leading OEM’s.
Products mentioned below are proven effective for the associated applications, but by no means represent the entirety of MACtac’s product offering. Our
Sales and Technical Marketing teams are ready to provide specific product recommendations.
Application Product Substrates Product Benefit
Heat,SoundandVibrationInsulation
IB118XIB1175AER
IF201X
Flatand/ormoldedrubbertometal, plastic and other substrates
The IB118X family provides excellent tack and better heat and shear resistance than other rubber adhesives. Available in a variety of widths and liner thickness, many IB118X products have been tested to automotive standards. IB1175AER flows more easily to adhere to challenging substrates with an easy removable liner.
Non-SlipTape IC6187 Painted & unpainted metal, plastic, wood and other substrates
MACtac Safety Grit provides non slip surfaces for a wide varietyofsubstratesinMarine,RVandindustrialequipment.
DecorativeGraphics Various Various For more information on a wide variety of Graphic Products contactyourSalesRepresentative.
Mirror Mounting IM2908-80IM2901
Coated mirror to ABS and other molded plastics
IM2908-80 is a proven product in the automotive industry for anti-shatter requirements in a challenging environment.
Gaskets/Seals IB118XIB2125AIB213X
Bonding similar & dissimilar materi-als – metals and plastics
IB1182’sHighTackRubberAdhesiveisacosteffectivesolutionwith good initial adhesion and shear strength. IB2125A uses one side rubber, one side acrylic for applications with different substrate requirements.
Roof/WallAssembly GS-Series Bonding similar & dissimilar materials – metals and plastics
GS-Series thick mass of adhesive from 5 to 50mils provides a very aggressive bond for high shear applications. GS-Series allows for elimination of rivets and mechanical fasteners, and acts as a seals substrates from moisture.
InteriorTrim IB6280IF2083IB213X
Foam-backed fabrics & PVC’s to fiberglass & other plastics
IB6280’s High Performance Acrylic combined with a Scrim Carrier provides structure that is still conformable for curved and uneven substrates. Available with different coat weights, and in Freefilm and Double-coated PET.
DeckingMaterial IB2180IF209X
Smooth and non-skid fiberglass to semi-rigid flooring
Specially designed to withstand the harsh marine environment and resist plasticizer migration, the IF209X family offers exceptional performance for demanding applications.
Carpet/Flooring IB2180IF209X
Fiberglass & other plastics to car-pet backings
Initially repositionable, the IF209X free films and double-coats build adhesion quickly, allowing for ease of installation and the removal of liquids and sprays commonly used today with almost no setting time.
Engine Cover IB2180 Fiberglass and other plastics to various sound-deadening foams
IB2180 provides heat resistance and adhesion necessary for foams and similar materials used in sound and vibration dampeninginmarineandRVenginecompartments.
pg.51
Specialty Products Rubber, Double-coated Films, Single Liner
email: [email protected]. MACtac.com/technical
AutomotiveApplicationsApplication IdeasMACtac offers a wide variety of pressure sensitive adhesives that have been certified to domestic and imported automotive standards. For a list of automotive certs or more information, please contact MACtac Customer Service at 1.800.321.0011
Products mentioned below are proven effective for the associated applications,
but by no means represent the entirety of MACtac’s product offering. Our Sales and Technical Marketing teams are ready to provide specific product recommendations.
Application Product Substrates Product Benefit
Nameplates IF2012A IF209XIM29XX
Painted Surface to Molded Plastic IF2012A High Performance Acrylic offers strong adhesion and peel strength to high surface energy metals and plastics. IF2092’s LSE adhesive provides excellent adhesion to lower surface energy materials such as powder coated paints.
RubberGaskets/Seals IB1182XIB2125AIB213X
RubbertoMoldedPlastic IB1182’sHighTackRubberAdhesiveisacosteffectivesolutionwith good initial adhesion and shear strength. IB2125A uses one side rubber, one side acrylic for applications with different substrate requirements.
DashboardAssembly/NavigationSystem
IF201XAIF2043B
PET Film to Molded Plastic Graphic Overlays and gauges can be assembled in thin profile with IF2012A Series or higher performing IF2043B for more challenging applications.
InteriorTrim IB6280IF2083IB213X
Foam Backed Fabric & Vinyl Molded Trim Materials to Filled PP
IB6280’s High Performance Acrylic combined with a Scrim Carrier provides structure that is still conformable for curved and uneven substrates. Available with different coat weights, and in Freefilm and Double-coated PET.
Carpet/Shoddy IB1188IB1184
GS
WovenCarpet/ShoddytoTPO/Metal
IB1184's heavy coat weight flows well into irregular surfaces. IB1188 uses a differential coat weight to reduce cost where one substrate is more challenging than the other. From 5 to 50 mils thick, GS-Series rubber based adhesive provides tremendous bonding of a wide variety of adhesives.
TailightConstruction IB1182 RubbertoMoldedPlastic IB1182'sHighTackRubberAdhesiveisacosteffectivesolutionwith good initial adhesion and shear strength.
Sound/VibrationDampening
IB118XIB1175AER
Felt/Nonwoven/FoamtoTPO/Metal
MACtac has a wide array of products for Sound and Vibration, from high tack rubber IB118X series, to the very easy release IB1175AER series for soft, easily torn materials. Acrylic and Rubber/Acrylicproductsarealsoavailable.
Mirror Mounting IM2908-80IM2901
Coated Mirror to ABS IM2908-80 is a proven product in the automotive industry for anti-shatter requirements in a challenging environment.
Transmission/ClutchFrictionDisc
IF4023IF4020
Ferrous and Non-Ferrous Metal to Carbon
IF4023 Phenolic products hold up under high heat and pressure to provide structural adhesion of carbon friction components.
HVACDucts IB1185L12IB1175AERIB2125A
Foam to TPO Plastic IB1185L12’s 12pt tag liner acts as a tray for diecut parts, allowing for ease of hand assembly and otherwise makes starting the liner easier on materials with low internal strength. IB1175AER’s 80# liner removes smoothly and easily from foam/felt/shoddy.
pg. 52
Phone: 1-800-328-2619
FoamFabricationAdhesive Recommendations
Chemistry ProductPE Foam PE Foam
4# to 6# Volara Foam
4# to 6# Volara Foam
Mincel Foam Mincel Foam PVC Foam PVC Foam
30 Min. 1 Week 30 Min. 1 Week 30 Min. 1 Week 30 Min. 1 Week
Rubber
IB1175A + ++ ++ +++ ++ +++ +++ +++IB1178A + ++ + +++ + +++ ++ +++IB1182/-3/-5 + ++ ++ +++ + +++ ++ +++IB1184 ++ +++ +++ +++ ++ +++ +++ +++IB1190A + ++ ++ +++ ++ +++ +++ +++
Acrylic
IB2012 + ++ + ++ + ++ + ++IF2015 + ++ ++ ++ ++ ++ ++ ++IB2092/IF2095 ++ +++ +++ +++ +++ +++ +++ +++IB2100 + ++ + ++ + +++ + ++IB2130 + ++ + +++ + +++ +++ +++
++
Chemistry Product
Neoprene Foam SCE
41, 43
Neoprene Foam SCE
41, 43
Poron Foam
Poron Foam
Vinyl Nitrile Foam
Vinyl Nitrile Foam
2#, 4#, 6# UL Ester
Urethane Foam
2#, 4#, 6# UL Ester
Urethane Foam
EPDM Foam
EPDM Foam
30 Min. 1 Week 30 Min. 1 Week 30 Min. 1 Week 30 Min. 1 Week 30 Min. 1 Week
Rubber
IB1175A ++ +++ ++ +++ ++ +++ ++ +++ ++ +++IB1178A + ++ + ++ + +++ + +++ + +++IB1182/-3/-5 ++ +++ + +++ ++ +++ + +++ ++ +++IB1184 +++ +++ +++ +++ +++ +++ ++ +++ +++ +++IB1190A ++ ++ ++ +++ ++ +++ ++ +++ ++ +++
Acrylic
IB2012 + ++ + +++ + + + ++ ++ +++IF2015 ++ ++ ++ +++ ++ +++ ++ ++ ++ +++IB2092/IF2095 +++ +++ +++ +++ +++ +++ +++ +++ +++ +++IB2100 + ++ + +++ + +++ + ++ ++ +++IB2130 + ++ ++ +++ ++ +++ + +++ ++ +++
These recommendations are based on previous history and testing and do not mean that all recommended products will work as every application is unique. It is the sole responsibility of the customer to determine fitness for use in each application prior to the purchase of any MACtac product
+ mild Bond, Improved with Pressure or Heat++ Agressive Bond +++ Destruction of Foam When Removed
pg. 53
email: [email protected]. MACtac.com/technical
MACtac®ProductsYouShouldKnowBasket of 12Product Ct Wt mil
Field/Factory Carrier Master RollSample Roll MSI Peel Tack Temp
Max Performance Description Liner Recommended For
Rub
be
r
IB1178A 1.2/1.2 1/2 mil PET54” x 750’
6” x 30’486 8.0/8.0 10.0/10.0 180°F Good
Cost effective general purpose bonding to smooth surfaces
60# White SCK
Any general performance bond
IB1190A 1.2/1.8 1/2 mil PET54” x 750’
6” x 30’486 8.5/9.5 10.5/12.5 180°F Better
Great tack and peel on a wide variety of substrates especially
non-plasticized foams and gaskets. A cost
effective solution to foam bonding and
other more challenging substrates
60# White SCK
Foam Fabrication, Gasketing, PET
Urethane foam, PE Foam, sponge, plastic, rubber, compressed
sheet
IB1200A 2.7/2.7 1.0 mil PP54” x 750’
6” x 30’486 11.5/12.0 6.0/4.5 180°F Best!
Heavy coat-weight for high performance
requirements. 1-mil PP carrier for excellent
conformability while increasing the integrity of your bond
60# White SCK
Very high performance applications
OEM Specification, PE Foam, sponge,
plastic, rubber, cork, compressed sheet
DC
Fo
am
Tap
e
IM1900A 1.8/1.81/32” white
PE foam54” x 216’
1” x 5’140 *** *** 150°F Good
General purpose bonding and mounting
between irregular and LSE substrates.
80# White SCK
Appliance / assembly aid
IM1800A 2.7/2.71/32” white
PE foam54” x 216’
1” x 5’140 *** *** 150°F Better
High coat-weight, high performance
bonding and mounting between irregular and LSE substrates.
80# White SCK
General purpose mounting
application. Moderate to High shear mounting
IM2908 2.0/2.01/32” black
PE foam54” x 216’
1” x 5’140 *** *** 200°F Best!
High performance Acrylic Foam Tape
80# White SCK or 5.0 mil
blue HDPE
Soap Dispenser or mirror mounting. High
shear mounting
Ac
rylic
DC
IB2101 1.1/1.1 1/2 mil PET54” x 750’
6” x 30’486 3.5/3.0 2.4/2.5 250°F Good
Acrylic double-coat, resistant to plasticizers, high temperatures,
and chemicals in a cost effective coat weight
60# White SCK
Cost effective bonding, mounting,
nameplates, faceplates,
decorative trim, PET Urethane,
Polyether, PVC Foam
IB2130 1.5/1.8 1/2 mil PET54” x 750’
6” x 30’486 4.5/4.5 6.5/6.5 250°F Best!
Modified-Acrylic, excellent temperature
resistance, tack, peel and shear on a
wide variety of substrates
74# White SCK
For High-Tack, High-Temperature
application, gasket, seals, automotive,
appliance.
Ac
rylic
FF
IF2012A 2.0 mil None54” x 540’
6” x 30’350 4.1 4.0 250°F Bood
UL rated, high performance acrylic,
2 MIL, high shear with UV and temperature resistance
83# Brown PCK
Cost effective acrylic bonding
applications, nameplates, faceplates,
gaskets, foams
IF2015A 5.0 mil None54” x 540’
6” x 30’350 5.0 5.5 250°F Best!
UL rated, high performance acrylic,
5 MIL, high shear with UV and temperature resistance
83# Brown PCK
High performance acrylic bonding
applications, nameplates, faceplates,
gaskets, foams
LSE
Ac
rylic
FF IF2092 2.0 mil None
54” x 540’6” x 30’
350 7.0 7.0 250°F Good2 mil High performance
acrylic freefilm, LSE74# White
PCK
LSE PP, PE, Powder-coated paints,
aggressive peel and tack
IF2095 5.0 mil None54” x 540’
6” x 30’350 10.0 10.0 250°F Best!
5 mil High performance acrylic freefilm, LSE
74# White PCK
Heavy coat-weight LSE PP, PE, Powder-
coated paints, aggressive peel and
tack
pg.54
Phone: 1-800-328-2619
Conversions&FractionsMetric to Inchesmillimeters Decimal Inches 1mm .03937 2mm .07874 3mm .11811 4mm .15748 5mm .19685 6mm .23622 7mm .27559 8mm .31496 9mm 35433 10mm .39370 11mm .43307 12mm .47244 13mm .51181 14mm .55118 15mm .59055 16mm .62992 17mm .66929 18mm .70866 19mm .74803 20mm .78740 21mm .82677 22mm .86614 23mm .90551 24mm .94488 25mm .98425
Thickness Conversion Formulas Inches x 0.0833 = Feet Inches x 25.4 = mm Inches x 25,400 = Microns mils x 25.4 = Microns mils x 0.001 = Inches Microns x 0.03937 = mils Microns x 0.0001 = cm mm x 1000 = Microns mm x 39.37 = mils .0254 x mils = mm
Metric to InchesThese formulas provide a simple method for converting frequent-ly encountered units for web or sheet materials.
MSI (1000 square inches) to: MSI divided by 0.144 = Ft2 (square feet) [Example: 25 MSI ÷ 0.144 = 173.61 Ft2]
MSI divided by 1.296 = Yd2 (square yards) [Example: 25 MSI ÷ 1.296 = 19.29 Yd2]
MSI divided by 1.550 = m2 (square meters) [Example: 25 MSI ÷ 1.550 = 16.13 m2]
Ft2 (square feet) to: Ft2 times 0.144 = MSI (1000 square inches) [Example: 200 Ft2 x 0.144 = 28.8 MSI]
Ft2 times 0.1111 = Yd2 (square yards) [Example: 200 Ft2 x 0.1111 = 22.22 Yd2]
Ft2 times 0.0929 = m2 (square meters) [Example: 200 Ft2 x 0.0929 = 18.58 m2]
Yd2 (square yards) to: Yd2 times 1.296 = MSI (1000 square inches) [Example: 200 Yd2 x 1.296 = 259.2 MSI]
Yd2 times 9.0 = Ft2 (square feet) [Example: 200 Yd2 x 9.0 = 1800 Ft2]
Yd2 times 0.8361 = m2 (square meters) [Example: 200 Yd2 x 0.8361 = 167.22 m2]
m2 (square meters) to: m2 times 1.55 = MSI (1000 square inches) [Example: 50 m2 x 1.55 = 77.50 MSI]
m2 times 10.7639 = Ft2 (square feet) [Example: 50 m2 x 10.7639 = 538.20 Ft2]
m2 times 1.196 = Yd2 (square yards) [Example: 50 m2 x 1.196 = 59.80 Yd2]
MSI to lineal feet for a 54” wide web MSI divided by 0.648 = lineal feet [Example: 500 MSI ÷ 0.648 = 771.6 lineal feet]
Lineal feet to MSI for a 54” wide web Lineal feet times 0.648 = MSI (1000 square inches) [Example: 250 lineal feet x 0.648 = 162 MSI]
MSI to lineal feet for 60” wide web MSI divided by 0.720 = lineal feet [Example: 500 MSI ÷ 0.720 = 694.4 lineal feet]
Lineal feet to MSI for a 60” wide web Lineal feet times 0.720 = MSI (1000 square inches) [Example: 250 lineal feet x 0.720 = 180 MSI]
pg. 55
email: [email protected]. MACtac.com/technical
Conversions&FractionsConversion FormulasLocate the known unit of measurement across the top row. Find the unknown unit of measurement down the left column. Follow the appropriate row and column until they intersect. Multiply the number listed at the point of intersection.
Units of Length
mili- Centi- UNIT Inch Foot Yard meter meter Meter (in) (ft) (yd) (mm) (cm) (m)
inch 1 12 36 0.03937 0.3937 39.37
foot 0.08333 1 3 0.00328 0.0328 3.281
yard 0.02777 0.333 1 0.00109 0.0109 1.094
mm 25.4 304.8 914.4 1 10 1000
cm 2.54 30.48 91.44 0.1 0 100
meter 0.0254 0.305 0.915 0.001 0.01
Units of Capacity - U.S. Liquid Measure
Fluid mili- CubicUNIT Ounce Quart Gallon liter Liter Inch (fl oz) (qt) (ga) (ml) (l) (in£)
fl oz 1 32 128 0.0338 33.8148 0.5541
quart 0.03125 1 4 0.00106 1.0567 0.01732
gallon 0.0078 0.25 1 0.000264 0.264 0.00433
ml 29.57286 946.3316 3785.327 1 1000 16.387
liter 0.02957 0.9463 3.7853 0.001 1 0.01639
in£ 1.80469 57.75 231 0.06102 61.02 1
Fraction EquivalentsFractional Inches Decimal Inches millimeters
1/64 0.015625 0.397
1/32 0.031250 0.794
3/64 0.046875 1.191
1/16 0.062500 1.588
3/32 0.093750 2.381
1/8 0.125000 3.175
5/32 0.156250 3.969
3/16 0.187500 4.763
7/32 0.218750 5.556
1/4 0.250000 6.350
9/32 0.281200 7.144
5/16 0.312500 7.938
11/32 0.343700 8.731
3/8 0.375000 9.525
13/32 0.406200 10.319
7/16 0.437500 11.113
15/32 0.468700 11.906
1/2 0.500000 12.700
17/32 0.531200 13.494
9/16 0.562500 14.288
19/32 0.537500 15.081
5/8 0.625000 15.875
21/32 0.656200 16.669
11/16 0.687500 17.463
23/32 0.718700 18.256
3/4 0.750000 19.050
25/32 0.781200 19.844
13/16 0.812500 20.638
27/32 0.843700 21.431
7/8 0.875000 22.225
29/32 0.906200 23.019
15/16 0.937500 23.813
31/32 0.968700 24.606
1 1.000000 25.400
pg.56
Phone: 1-800-328-2619
Conversions&FractionsThickness Conversion Chart
mils Microns1 25.4
2 50.8
3 76.2
4 101.6
5 127.0
6 152.4
7 177.8
8 203.2
9 228.6
10 254.0
11 279.4
12 304.8
13 330.2
14 355.6
15 381.0
16 406.4
17 431.8
18 457.2
19 482.6
20 508.0
21 533.4
22 558.8
23 584.2
24 609.6
25 635.0
Metric to Inchesmillimeters Decimal Inches1 .3937
2 .07874
3 .11811
4 .15748
5 .19685
6 .23622
7 .27559
8 .31496
9 .35433
10 .39370
11 .43307
12 .47244
13 .51181
14 .55118
15 .59055
16 .62992
17 .66929
18 .70866
19 .74803
20 .78740
21 .82677
22 .86614
23 .90551
24 .94488
25 .98425
Converting Multipliers
12 inches .03937 mils 1 foot 1 micron
25.4 mm 1,000 microns 1 inch 1 mm
.001 inches 39.37 mils 1 mils 1 mm
25,400 microns .0254 mm 1 inch 1 mils
25.4 microns .0001 cm 1 mils 1 micron
Thickness Conversion Formulas
Inches x 0.0833 = Feet
Inches x 25.4 = mm
Inches x 25,400 = Microns
mils x 25.4 = Microns
mils x 0.001 = Inches
Microns x 0.03937 = mils
Microns x 0.0001 = cm
mm x 1000 = Microns
mm x 39.37 = mils
CUSTOMER INFORMATION PROFILE
Mail to: MACtac or Fax to: MACtac Salesman Name:Credit Dept. Credit Dept. Territory No:4560 Darrow Road (330) 688-5461Stow, OH 44224-1898 (800) 223-3117
Company Name Business Structure:
Any other company name used Proprietorship Partnership Corporation
Billing Address Date Established Federal Tax ID No.
City, State & Zip Code Tax Exempt Yes No Duns No.
Phone No. Fax No.
Owners or OfficersName & Title Social Security Number
If this is a U.S. company and tax exempt, pleasecomplete and return the attached multi-stateExemption/Resale Certificate. In the absence ofan exemption certificate, the law compels us toconsider all sales to you subject to tax.
Home Address Home Phone % Ownership If Corporation: State Incorporated
Name & Title Social Security Number Branch Yes No Subsidiary Division
Home Address Home Phone % Ownership Parent Company
Name & Title Social Security Number Address
Home Address Home Phone % Ownership Address Phone No.
Accounts Payable Manager & Accounts Payable Contact:Name Title Phone No.
Name Title Phone No.
Estimated monthly purchases from MACtac $___________Have our terms of sale been explained to you? Yes No
TERMS AND CONDITIONS:Terms As stated on individual invoice. If the invoice reflects that a discount is available, the payment must be
received by the discount date.
Service charge A charge of 2% per month (24% per annum) is charged on all accounts 15 days or more past due.
Additional fees In the event suit is filed to enforce payment, signer(s) agree to reasonable collection cost and attorneyfees as allowed by law
Returns Restocking charge on all goods returned for credit will be applied.
Please return this application, including financial statement. Be assured that any information provided will be held in strictestconfidence and be used only for our credit granting purposes. Applicants signatures attest financial responsibility, ability andwillingness to pay our invoices in accordance with invoice terms. The above information as well as that on the reverse side isfor the purpose of obtaining credit.
I agree to comply with the above terms, and certify that all information furnished is accurate. I authorize MACtac tocontact creditors, or any credit reporting agency, to obtain ratings now and any time hereafter.
Firm Name _____________________________________
Print name _____________________________________ Title _____________________________
Signed by _____________________________________ Date ________________
Print name _____________________________________ Title _____________________________
Signed by _____________________________________ Date ________________
PLEASE COMPLETE OTHERSIDE OF FORM.
Primary Bank Reference:Bank Contact Officer Phone No. Fax No.
Address City State Zip Code
Loan Type Loan Account # Checking Account # Savings Account #
Primary Supplier References:Name Name
Address Address
City, State & Zip Code City, State & Zip Code
Phone No. Fax No. Phone No. Fax No.
Name Name
Address Address
City, State & Zip Code City, State & Zip Code
Phone No. Fax No. Phone No. Fax No.
Year ________ Year ________ Year ________CURRENT ASSETS:
Cash ___________________ ___________________ ___________________
Accounts receivable ___________________ ___________________ ___________________Inventory ___________________ ___________________ ___________________Other current assets ___________________ ___________________ ___________________
Total ___________________ ___________________ ___________________
FIXED ASSETS:Machinery & equipment ___________________ ___________________ ___________________Land & buildings ___________________ ___________________ ___________________Other fixed assets ___________________ ___________________ ___________________Less depreciation ___________________ ___________________ ___________________
Total ___________________ ___________________ ___________________
CURRENT LIABILITIES: _________________ _________________ _________________Accounts payable ___________________ ___________________ ___________________Short-term loans ___________________ ___________________ ___________________Current portion of long-term debt ___________________ ___________________ ___________________Other current liabilities ___________________ ___________________ ___________________
Total ___________________ ___________________ ___________________
LONG-TERM LIABILITIES:Long-term debt, less current portion ___________________ ___________________ ___________________Other liabilities ___________________ ___________________ ___________________
Total ___________________ ___________________ ___________________
INCOME STATEMENT:Sales less returns and allowances ___________________ ___________________ ___________________
Less cost of goods sold ___________________ ___________________ ___________________Gross Profit ___________________ ___________________ ___________________Less operating expenses ___________________ ___________________ ___________________Operating income ___________________ ___________________ ___________________Less other expenses ___________________ ___________________ ___________________Net income (loss) ___________________ ___________________ ___________________
FIGURES ARE: Audited Unaudited
pg.59
email: [email protected]. MACtac.com/technical
AdditionalInformationOrder Lead Times / Business Rules
SlittingonStockProducts: 5 day lead time if entered and cleared by credit before 4pm EST
FinishedGoods: If stocked, can ship same day if entered and cleared by credit before 1pm EST, otherwise next day ship.
Sheeting: 5 day lead time
CustomProducts: Follow custom lead time
MACtac.comThefollowingitemsareavailableonourwebsite—www.MACtac.com,www.MACtac.com/technical
• Advanced Find - find products using multiple criteria
• PerformanceGuides
• ProductLiterature
• PressReleases
• TechnicalAssistanceBulletins
• FrequentlyAskedQuestions
pg.60
Phone:1-800-328-2619
Packaging&Labeling
Poker Packaging Cradle PackagingPallets will be selected to best match order widths, lengths and volumes.
Pallets will be selected to best match order widths, lengths and volumes.
Chip board / Deck Pads Chip board / Deck Pads
Rolls placed with labels lined up uniformly facing the outside of the length of the pallet.
Rolls placed with labels lined up uniformly facing the outside of the length of the pallet.
Release discs between rolls. Release discs between rolls.
2 x 2 angle board between roll cores. 2 x 2 angle board between roll cores.
Poly Sheet Plastic banded rolls to pallet through 2 x 2 angle boards
Stretch wrap Roll wedges
Pallet label placed on top end of the length side of pallet facing out
Poly sheet
Stretch wrap
Pallet label placed on top end of the length side of pallet facing out.
* Special Requests - Call Customer Service at 1-800-321-0011. Additional charges may apply.
Pallet Options
30” L x 30” W 48” L x 40” W
36” L x 36” W 48” L x 48” W
45” L x 45” W 54” L x 30” W
48” L x 30” W 60” L x 30” W
Carton Packaging Log Roll Carton PackagingPallets will be selected to best match order widths, lengths and volumes.
Pallets will be selected to best match order widths, lengths and volumes.
Chip board / Deck Pads Chip board / Deck Pads
Place poly bag into carton Poly bag each roll
Release paper on bottom and between rolls Upsom pad (fit to carton) with plastic plug (2113) and release disc on each end of the roll
Pilot core between roll cores (must be 2” from top)
May use upsom between layers for stability
Corner board
Polyband to pallet Lay carton down on skid
Stretch wrap Rope and stretch wrap
Pallet label placed on top end of the length side of the pallet. Pallet label placed on top end of the length side of the pallet.
* Special Requests - Call Customer Service at 1-800-321-0011. Additional charges may apply.
Pallets can contain mixed roll widths. All efforts will be taken to
keep mixed pallets to a minimum.
pg.61
Packaging&Labeling
email: [email protected]. MACtac.com/technical
Shop Order Number
Customer PO#
Customer Order Number
Product
Trace ID
Customer Part Number
Master Roll Stock Lot Number
Upended PackagingPallets will be selected to best match order widths, lengths and volumes.
Lengths and volumes
Upsom board
Roll on end
Upsom board
Wood top
Poly band to pallet / 4 ways
Stretch wrap
* Special Requests - Call Customer Service at 1-800-321-0011. Additional charges may apply.
pg.62
Phone:1-800-328-2619
pg.63
email: [email protected]. MACtac.com/technical
MACtac TECHNICAL ProductsInnovative Supplier of Engineered Pressure Sensitive Adhesives
MACtac North America • 4560 Darrow Road • Stow, OH 44224-1898 • ph:800.328.2619 • fax:330.688.1153 email: [email protected] • www.MACtac.com/technical
© 2012 Morgan Adhesives CompanyMAC4082 ver. 8 (04/12)MACtac, MACbond, MACfilm andMACmount are trademarks of Morgan Adhesives Company
Top Related