How to Make a Topographic Profile
This represents a very simple topographic map of a hill. The hill is steep on the left side (the contour lines are very close together) and has a gentle slope on the right side. The numbers represent the elevation of the contour lines. (*)
100200
300
400
What would the hill look like if you were to slice it from left to right? (*)
How to Make a Topographic Profile
Again, think of the cardboard analogy. Every layer of cardboard would represent 100 feet of elevation (the same as a contour line). You would have 4 layers of cardboard. Viewed from the side it would look like this (*)
100200
300
400
Each layer of the hill has a different piece of cardboard. To determine the size, draw lines from the hill down to the appropriate layer of cardboard. (*)
500 feet
400 feet
300 feet
200 feet
100 feet
Thus, you have a somewhat blocky profile of what the hill looks like. (*)
How to Make a Topographic Profile
100200
300
400
500 feet
400 feet
300 feet
200 feet
100 feet
Normally, the Earth’s surface is not this blocky. In a topographic profile a line is drawn from these points (red dots) producing a smooth transition. (*)
Thus you have a topographic profile. This is what the hill would look like if you were to cut it along the profile line and look at it from the side. (*)
Now it’s your turn. (*)
A B
This is the profile line – from A to B. Where this black line crosses the INDEX CONTOURS (you do not have to do every contour line) draw a line down to the appropriate contour elevation (layers) below. (*)
6400
The contour interval of this map is 40 feet. Every index contour would then be 200 feet.800
0
7000
760074007200
7800
68006600
Find this page in your Topo Worksheet Packet
A B
6400
The contour interval of this map is 40 feet. Every index contour would then be 200 feet.800
0
7000
760074007200
7800
68006600
In this region the profile line cut across the 7800 foot line 4 times.
(*)
The last step is to simply connect the “dots”. (*)
The profile is finished. (*)
A B
6400
The contour interval of this map is 40 feet. Every index contour would then be 200 feet.800
0
7000
760074007200
7800
68006600
This is a very classic example of a butte with steep sides and a very flat top. The profile that you see here is an exaggerated scale – the vertical scale is greater than the horizontal scale. The next example is where the vertical scale is closer to the horizontal scale. (*)
A B
In this example the butte is still the same horizontal distance, but the vertical scale has been compressed. If the vertical scale was bigger it would produce more exaggeration. (*)
These are just different representations of the same butte. On the test, the profile that you will be asked to draw will be simpler than this one. (*)
THE GRAND CANYON, ARIZONA
This view of the Grand Canyon is from the South Rim looking north into Bright Angel Canyon. This is what it looks like on a topographic map. (*)
THE GRAND CANYON, ARIZONA
This view of the Grand Canyon is from the South Rim looking north into Bright Angel Canyon. This is what it looks like on a topographic map. (*)
It may not be as majestic but it is full of information. (*)
Cumberland, Pennsylvania/MarylandBased on the slope information provided by the brown contour lines, the tributaries flow down fairly steep slopes (the contour lines are close together) making them YOUTHFUL streams. The main stream occupies a valley that has very few contour lines. In fact the wide spacing of these contour lines represents a floodplain – placing this river in the MATURE stage. (*)
Just for fun, let’s construct a topographic profile across the main stream from point A to point B. (*)
AA
BBTry to visualize what this profile would look like before you move on. (*)
Cumberland, Pennsylvania/Maryland
AA BB
Using every INDEX CONTOUR – 100 foot interval … (*)
11001000900
800
700
600
Print this page if you want to draw the profile. The next slide goes through the process. READY ? (*)
Top Related