7/25/2019 Honda Odyssey - Replaceing Front Bumper - Manual
1/13
2006 American Honda Motor Co., Inc - All Rights Reserved. AII 33173 (0607) 1 of08F01-SHJ-1000-91
PART LIST
Front under spoiler
5 Stepped bolts
2 Square head bolts
2 Washer-nuts
4 Self-tapping screws
4 Spring nuts
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriverFlat-tip screwdriver
Ratchet
10 mm Socket
Drill
3 mm, 6 mm, 8 mm and 10 mm Drill bits
Center punch
File
Blanket
Masking tape
Isopropyl alcoholShop towel
Eye protection (face shield, safety goggles, etc.)
INSTALLATION
INSTRUCTIONS
Accessory Application Publications No.
Issue Date
JULY 2006
2007 ODYSSEYFRONT UNDER SPOILER
AII 33173
INSTALLATION
Customer Information: The information in thisinstallation instruction is intended for use only by
skilled technicians who have the proper tools,equipment, and training to correctly and safely addequipment to your vehicle. These procedures
should not be attempted by do-it-yourselfers.
NOTE:
Be careful not to damage the front bumper and
body paint finish.
This front under spoiler kit should be installed only
if the ambient air temperature is 60F (15C) orabove.
To allow the adhesive to cure, do not wash thevehicle for 24 hours.
www.collegehillshonda.com
7/25/2019 Honda Odyssey - Replaceing Front Bumper - Manual
2/13
2 of 5 AII 33173 (0607) 2006 American Honda Motor Co., Inc - All Rights Reserved.
1. Remove the front bulkhead cover (ten clips).
With Front Corner Sensors:
2. Remove the front bumper (two bolts, eight clips,and two self-tapping screws and pull the bumper
out towards you). If equipped, unplug the fog lightconnectors. If equipped, unplug the front cornersensor connectors. Place the front bumper on a
blanket to install the front under spoiler.
Without Fog Lights and Front CornerSensors:
4121010Y
CLIP (8)
BULKHEADCOVER
LONGCLIP
4121021Y
SELF-TAPPINGSCREW
BOLT
LONG CLIP
FRONTBUMPER
SELF-TAPPINGSCREWCLIP
BOLT
With Fog Lights:
4311060Y
FOG LIGHTCONNECTOR
FOG LIGHTCONNECTOR
FRONT BUMPER
4728010Y
FRONTCORNERSENSORCONNECTOR
FRONTCORNERSENSORCONNECTOR
FRONTBUMPER
www.collegehillshonda.com
7/25/2019 Honda Odyssey - Replaceing Front Bumper - Manual
3/13
2006 American Honda Motor Co., Inc - All Rights Reserved. AII 33173 (0607) 3 of
4. On the inside of the bumper, locate the sevenscribed marks. Center punch each scribed mark.
5. While wearing eye protection, drill two 8 mm holesthrough the front bumper. First drill with a 3 mm
drill bit, then finish with an 8 mm drill bit.
6. While wearing eye protection,drill five 10 mmholes through the five center-punched marks alongthe bottom of the bumper. First drill with a 3 mm
drill bit, then with a 6 mm drill bit, and finish with a10 mm drill bit.
7. Using a file, remove any burrs from the drilledholes.
4716020Y
FRONTBUMPER
CENTERPUNCH
CENTERPUNCH
SCRIBEMARK (7)
4716030Y
DRILL(3 mm 8 mmDRILL BIT)
FRONTBUMPER
CENTER-PUNCHEDMARKS (2)
4716040Y
DRILL(3 mm 6 mm
10 mm DRILL BIT)FRONTBUMPER
CENTER-PUNCHEDMARKS (5)
3. Locate the four dimples at the fenderwell area ofthe front bumper. While wearing eye protection,
drill a 6 mm hole through each dimple. Start with a3 mm drill bit and finish with a 6 mm drill.
4716011Y
FRONTBUMPER
DIMPLE
DRILL(3 mm 6 mmDRILL BIT)
DIMPLE
www.collegehillshonda.com
7/25/2019 Honda Odyssey - Replaceing Front Bumper - Manual
4/13
4 of 5 AII 33173 (0607) 2006 American Honda Motor Co., Inc - All Rights Reserved.
9. Slide one square head bolt into each bracket on
the front under spoiler.
11. Using isopropyl alcohol on a shop towel, clean the
front bumper where the under spoiler will attach.
12. Position the under spoiler on the front bumper, and
install a washer-nut to each square-head bolt.
10. Attach a strip of masking tape to the end of eachadhesive backing, then pull back 1 to 2 inches
of the adhesive backing. Fold the ends back, andtape them to the front of the spoiler.
FRONTBUMPER
FRONT UNDERSPOILER
4220050YWASHER-NUTS
4220030Y
SPOILERBRACKET
SQUAREHEAD BOLT
Slide onto thebracket.
FRONT UNDERSPOILER
4220042YFRONT UNDERSPOILER
ADHESIVE BACKINGS (6)Fold back the ends and tapethem to the surface of the front
under spoiler.
8. Slide one spring nut over each of the four holesyou drilled at the fenderwell area of the bumper.
4220020Y
FRONT BUMPER
HOLESDRILLEDIN STEP 3.
SPRINGNUTS
SPRINGNUTS
SPRINGNUT
HOLESDRILLEDIN STEP 3.
HOLESDRILLEDIN STEP 3.
www.collegehillshonda.com
7/25/2019 Honda Odyssey - Replaceing Front Bumper - Manual
5/13
2006 American Honda Motor Co., Inc - All Rights Reserved. AII 33173 (0607) 5 of
14. At the edge of the spoiler/bumper, loosely installthe four self-tapping screws.
15. With the help of an assistant, gently pull the sidesof the bumper around the fenderwell and install
the front bumper. If equipped, plug in the fog lightconnectors. If equipped, plug in the front corner
sensor connectors. Make sure the center rubbersplash protector is above the bottom bumper
edge. Reinstall the six clips, two bolts, and twoself-tapping screws to secure the bumper.
13. Secure the front bumper to the front under spoilerusing the five stepped bolts.
16. While holding light pressure on the spoiler,carefully remove the adhesive backings. Hold the
spoiler firmly against the front bumper with thepalm of your hand for 30 seconds, particularly atthe edges.
17. While holding the edge of the spoiler against thebumper, tighten the four self-tapping screws
installed in step 14.
18. Reinstall the front bulkhead cover.
4511220Y
FRONT UNDERSPOILER
SELF-TAPPINGSCREW
FRONTBUMPER
SELF-TAPPINGSCREW
4407060Y
SPLASHGUARD
RUBBER
SPLASHGUARD
CENTER RUBBERSPLASHPROTECTOR
CLIP(reused.)
FRONTBUMPER
CLIPS(6: reused.)
FRONTBUMPER
FRONT BUMPER
CLIP (reused.)BOLTS(reused.)
BOLTS(reused.)
SELF-TAPPINGSCREW(reused.)
SELF-TAPPINGSCREW(reused.)
4220061Y
FRONT
BUMPER
STEPPED BOLT
FRONTUNDERSPOILER
SELF-TAPPINGSCREWInstall loosely.
SELF-TAPPINGSCREWInstall loosely.
4220072YFRONTUNDER
SPOILER
FRONT BUMPER
ADHESIVE BACKINGS (6)Carefully remove whileholding pressure on thespoiler.
www.collegehillshonda.com
7/25/2019 Honda Odyssey - Replaceing Front Bumper - Manual
6/13
6 of 5 AII 33173 (0607) 2006 American Honda Motor Co., Inc - All Rights Reserved.
Give a copy this page to your customer.
When towing Odyssey, follow the instructions described in the vehicle Owners Manual.
When using the front towing hook, make sure to remove the front bumper with front under spoiler. Failure to
follow this precaution could damage the vehicle, the front bumper, and the front spoiler.
4727020Y
www.collegehillshonda.com
7/25/2019 Honda Odyssey - Replaceing Front Bumper - Manual
7/13
2006 American Honda Motor Co., Inc. - All Rights Reserved. All 33187 (0607) 1 of
INSTALLATION
INSTRUCTIONS
Accessory Application Publications No.
Issue Date
08F04-SHJ-1000-91
JULY 2006
2007 ODYSSEYSIDE UNDER SPOILER
PARTS LIST
Left side under spoiler
Right side under spoiler
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
Blanket
INSTALLATION
NOTE:
To prevent damage, place a blanket under the sideunder spoilers during installation.
These instructions show the left side under spoilerbeing installed. The same procedure applies to
installing the right side under spoiler.
Optional splash guards cannot be used with the
side under spoilers.
1. Open the front and rear doors. Remove the self-
tapping screw that fasten the left side sill panel tothe left front inner fender. Slide the side sill panel
forward, then remove it by pulling it out towardyou.
2. Remove the 13 clips from the side sill by turningthem 45.
26 Seals
4114010Y
LEFT SIDESILL PANEL
FRONT
LEFT FRONTINNER FENDER
LEFT SIDESILL PANEL
SELF-TAPPINGSCREW (Reuse.)
4114020YCLIPS (13)(Reused.)
Turn 45 toremove.
FRONT
LEFT SIDE SILL
LEFT SIDE SILL
All 33187
www.collegehillshonda.com
7/25/2019 Honda Odyssey - Replaceing Front Bumper - Manual
8/13
2 of 2 All 33187 (0607) 2006 American Honda Motor Co., Inc. - All Rights Reserved.
3. On the inside of the new under spoiler, install the
13 clips you removed to the holders through thecutout as shown. Make sure the clips fit properlyin the cutouts.
5. Position the left side under spoiler on the body
under the front inner fender, and push the clipsyou just installed into the square holes in thebody. Use the palm of your hand to click all 13
clips into place.
6. Reinstall the self-tapping screw removed in step 1.
4. Remove the old seals from the 13 clips, andinstall the new seals from the kit.
4114040Y
LEFT SIDEUNDER SPOILER
CLIPS(13)
SEAL
OLD SEAL(Replace.)
4114050YSQUAREHOLE CLIP
LEFT SIDEUNDER SPOILER
FRONT
4114060Y
LEFT FRONTINNER FENDER
SIDE UNDERSPOILER (LEFT)
SELF-TAPPINGSCREW (Reused.)
4114031Y
CLIPS (8)(Center align theclip with the rib.)
CLIPS (5) (reused)(Note the installationdirection.)
LEFT SIDEUNDERSPOILER
CLIPS (8) (Reused.)(Note the installationdirection.)
CUTOUT
RIBS (8)
CUTOUT
7. Repeat steps 1 thru 6 to install the right side under
spoiler.
www.collegehillshonda.com
7/25/2019 Honda Odyssey - Replaceing Front Bumper - Manual
9/13
2006 American Honda Motor Co., Inc. - All Rights Reserved. AII 33181 (0607) 1 of08F03-SHJ-1000-91
INSTALLATION
INSTRUCTIONS
Accessory Application Publications No.
Issue Date
JULY 2006
2007 ODYSSEYREAR UNDER SPOILER
NOTE: Optional splash guards cannot be used with
this rear with this rear under spoiler.TOOLS AND SUPPLIES REQUIRED
Phillips screwdriverFlat-tip screwdriver
Ratchet
10 mm Socket
Drill
3 mm, 8 mm, and 10 mm Drill bits
Clip remover
Felt-tip pen
File
Isopropyl alcohol
Shop towelMasking tape
Blanket
Pushpin
Eye protection (face shield, safety goggles, etc.)
INSTALLATION
Customer Information: The information in thisinstallation instruction is intended for use only by
skilled technicians who have the proper tools,equipment, and training to correctly and safely add
equipment to your vehicle. These procedures
should not be attempted by do-it-yourselfers.
NOTE:
Be careful not to damage the rear bumper andbody paint finish.
To prevent damage, rest the rear bumper on theblanket during the installation.
This rear under spoiler kit should be installed onlyif the ambient air temperature is 60F (15C) orabove.
To allow the adhesive to cure, do not wash the
vehicle for 24 hours.
PARTS LIST
Rear under spoiler
5 Long Stepped bolts
4 Short Stepped bolts
6 Square head bolts
2 Self-tapping screws
15 Washer-nuts
2 Spring nuts
4 Adhesive Collars
AII 33181
www.collegehillshonda.com
7/25/2019 Honda Odyssey - Replaceing Front Bumper - Manual
10/13
2 of 5 AII 33181 (0607) 2006 American Honda Motor Co., Inc. - All Rights Reserved.
2. On the inside of the bumper, locate the 13 marked
areas. Using a pushpin, pierce the bumper at the13 locations identified below. Double-check yourmarks before piercing through the bumper.
1. Remove the rear bumper:
If equipped, remove two screws and threeclips that secure the inner fender.
Remove the four self-tapping screws (two oneach side) at the fenderwell.
Using a clip remover, pry out and remove the
three clips along the bottom of the bumper. Using a flat-tip screwdriver, pry out and
remove the bumper bolt cover covers, thenremove the four bumper bolts.
With the help of an assistant, release thebumper from the fenderwell, and slide the
bumper away from the vehicle.
If equipped, unplug the backup sensor
connectors.
Set the bumper on a blanket.
3. While a wearing eye protection, drill an 8 mm hole
through the two rear marks and the four sidemarks.
First drill with a 3 mm drill bit, then finish with
an 8 mm drill bit.
Remove any burrs from the edges of the holes
with a file.
4120011Y
BOLTS (4)
BOLTCOVERS(4)
REARBUMPER
CLIP
SELF-TAPPINGSCREWS (4)
SELF-TAPPINGSCREW(If equipped withinner fender.)
SELF-TAPPING SCREW(If equipped withinner fender.)
4727030Y
PUSHPIN
MARKEDAREAS (13)
REARBUMPER
MARK NOT USED(Do not piercethroughthis mark.)
REAR UNDERSPOILER MARK(Mark in the sameposition on theother side.)
MARK NOTUSED(Do notpiercethroughthis mark.)
REARBUMPER
4211031Y
DRILL(First drill witha 3 mm drillbit and finishwith an 8 mmdrill bit.)
REARBUMPER
MARKEDAREA (6)
www.collegehillshonda.com
7/25/2019 Honda Odyssey - Replaceing Front Bumper - Manual
11/13
2006 American Honda Motor Co., Inc. - All Rights Reserved. AII 33181 (0607) 3 of
4. Turn the bumper upside down. While wearing eye
protection, drill a 10 mm hole through each of theseven marks and two slots:
First drill with a 3 mm drill bit, then finish with a10 mm drill bit.
Remove any burrs from the edges of the holeswith a file.
5. On the inside of the rear under spoiler, locate thesix brackets (three on each side), Slide one
square head bolt into each bracket on the rearunder spoiler.
8. LX model only: Install one spring nut to the lowerbumper hole on each side at the fenderwell.
9. Using isopropyl alcohol on a shop towel, clean therear bumper where the rear under spoiler willattach.
6. Attach a strip of masking tape to the end of each
adhesive backing, then pull back 1 to 2 inchesof adhesive backing. Fold the ends back, and tape
them to the outer surface of the spoiler withmasking tape.
7. Using isopropyl alcohol on a shop towel, clean the
rear spoiler areas where the adhesive collars willattach. Remove the adhesive backing from eachadhesive collar, and attach the collar to the inside
of the rear spoiler in the areas shown.
4508020B
REARBUMPER
MARKEDAREA (7)
DRILL(First drill witha 3 mm drill bitand finish witha 10 mm drillbit.)
SLOT
4414012Y
SQUAREBOLT
ADHESIVEBACKINGS (5)(Fold the endsback, and tapethe ends tothe outer surfaceof the underspoiler.)
REARUNDERSPOILER
SQUARE HEADBOLTS (6)
BRACKET
4526020Y
REAR BUMPER
DIMPLESPRING NUT
SPRING NUT
DIMPLE
4211052Y
ADHESIVECOLLAR
ADHESIVEBACKING
REAR UNDERSPOILER
ADHESIVECOLLAR
ADHESIVE COLLARATTACHMENT POINT
ADHESIVECOLLARATTACHMENTPOINT
ADHESIVE
COLLAR
ADHESIVE COLLARATTACHMENT POINT
www.collegehillshonda.com
7/25/2019 Honda Odyssey - Replaceing Front Bumper - Manual
12/13
4 of 5 AII 33181 (0607) 2006 American Honda Motor Co., Inc. - All Rights Reserved.
12. While holding light pressure on the under spoiler,
carefully remove the adhesive backings from theunder spoiler. After attaching, hold the underspoiler firmly against the rear bumper with the
palm of your hand for 30 seconds, particularly atthe edges.
14. Install the self-tapping screws at the fenderwell.
13. Reinstall the rear bumper.
10. Position the rear under spoiler on the rear bumper,
and install a washer nut to each square-head bolt.Tighten the washer-nuts in the order shown.
11. Install the five long stepped bolts through the
inboard holes in the under spoiler, and install thefour short stepped bolts through the outboardholes in the under spoiler. Install a washer-nut on
each stepped bolt. Tighten the washer-nuts in theorder shown.
WASHER NUTS (9)REAR BUMPER
REAR UNDERSPOILER
4212021Y
WASHER NUTS (9) REAR BUMPER
REARUNDERSPOILER
LONGSTEPPEDBOLT
SHORTSTEPPEDBOLT
SHORTSTEPPEDBOLT
4719030Y
REAR UNDERSPOILER
REAR BUMPER
REAR BUMPER
REAR UNDERSPOILER
ADHESIVE BACKINGS (5)(Carefully remove whileholding pressure on theunder spoiler.)
REAR
BUMPER
SELF-TAPPINGSCREW
SELF-TAPPINGSCREW
SELF-TAPPINGSCREW
REAR UNDERSPOILER
SELF-TAPPINGSCREW
www.collegehillshonda.com
7/25/2019 Honda Odyssey - Replaceing Front Bumper - Manual
13/13
2006 American Honda Motor Co., Inc. - All Rights Reserved. AII 33181 (0607) 5 of
Give a copy of this page to your customer.
When towing the Odyssey, follow the instructions described in the vehicle Owners Manual.
When using the rear towing hook, make sure to remove the rear bumper with rear under spoiler. Failure tofollow this precaution could damage the vehicle, the rear bumper, and the rear spoiler.
4727010Y
www.collegehillshonda.com
Top Related