Logistic Systems for Packaging, Transportation and Storage
Quality Certification to DIN EN ISO 9001: 2000www.zarges.de
w
2
Contents
Contents
3
Characteristics of Aluminium ZARGES TransportationSystems and Reusable Packaging in Aluminium.
w Make sense from an economic, safe and ecological point of view:
Aluminium is a material that is lightin weight and highly robust:The density of aluminium is only around
2.6 to 2.8 g/cm3. This is approximately1/3 rd of the density of steel. Despite its
low weight aluminium features very
high strength characteristics.
Aluminium is impervious to watervapour:Even under extremely long-term storage
conditions, it is impossible for moisture
to penetrate the material. By means of
welding it is possible to fabricate an alu-
minium container so that it is resistant
to water vapour.
Aluminium is resistant to impact andvery strong:The surface may be dented by impact
but the impact energy is absorbed by
the distortion.
Aluminium is not sensitive to extremefluctuations in temperature:In the temperature range of – 40 to
+80 °C the material characteristics
remain constant.
Aluminium is resistant to corrosionand has a built-in defensive response:On contact with oxygen the surface
develops an oxide layer which is rein-
stated immediately if damage occurs.
Aluminium is hygienic:The smooth surface is easy to clean
and neutral in terms of odour. Alu-
minium containers are eminently
suitable for areas where hygiene is
a primary requirement.
Aluminium conducts electricity:Aluminium is a good conductor of
electricity and heat, an advantage with
housings for electronic installations
for example.
Aluminium is magnetically neutral:Aluminium is free from ferro-magnet-
ism. This material characteristic may
assume major importance for certain
application.
Aluminium is fully recyclable:Old aluminium can be melted down and
re-used – a positive contribution towards
relieving the burden of waste disposal
and protecting the environment.
Aluminium is resistant to UV radiation:Long storage periods and use under
exposure to UV rays have no effect on
this material.
Aluminium lends itself to machining in a number of different ways:All the standard machining processes –
welding, moulding etc. – can be applied
to aluminium and can be carried out
very much more cost-efficiently than is
the case with other metals.
w ZARGES, a leading company in the aluminium processing sector, has recognised the advantages of this material for decades. The result is a wide range of boxes, crates, cases, baskets, trolleys and individual special designswhich will help you find solutions to your logistics problems. Our long-lasting reusable equipment makes a valuablecontribution to protecting the environment.
w Characteristics of Aluminium . . . . . . . . . . . . . . . . . . . . . . . . . 3
w K470 Universal Container K470 . . . . . . . . . . . . . . . . . . . . . . . 4
w K470 Universal Container – Accessories . . . . . . . . . . . . . . . . 14
w K450 Containers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
w Tool- and Rollbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
w K410 Alu-Cases K410 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
w Service and Attaché Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
w P472 Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
w P402 Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
w Retou ® Collapsible Container . . . . . . . . . . . . . . . . . . . . . . . . 25
w Transport and Storage Container K475 . . . . . . . . . . . . . . . . . 26
w Mitraset® 19˝electronic housing . . . . . . . . . . . . . . . . . . . . . . . 27
w Flat pallets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
w Baskets and cases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
w Dolly trolleys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
w Box trolleys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
w Open trolleys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
w Cupboard and cage trolleys . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
w Accessories for cupboard trolleys and special fittings . . . . . 40
w Recyclable waste systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
w ZARGES individual solutions . . . . . . . . . . . . . . . . . . . . . . . . . . 43
4
ZARGES Universal Containersan innovation spanning more than 50 years
w Stackable universal container.w Lid with stainless steel hinge, two straps
and peripheral foam seal to lid.w Robust edge, lid and floor profile.w Peripheral beading and corner beading
for enhanced shape retention.w Alloy cast stacking corners.w Snaplocks. Can be secured by using lock
and key, lead seals or padlock.w Ergonomic drop-type handles with
high carrying capacity.w Stackable and palletisable, to suit
pallet sizes to DIN 15 141.w For practical dolly trolleys for the
K470 universal case see page 30.
ZARGESK470 Universal Container
ZARGES Universal Containers – in the forefront of innovationfor more than 50 years The Universal Container K470 is a realclassic. Developed way back in 1950, today it still continues to stand for the power of innovation, the highest standards ofquality, maximum functionality and convincing design. Char-acteristics that have made it into a model for the majority ofthe ZARGES logistics products. It has been redesigned twice,consistently taking account of the latest state of technologyand with the addition of useful accessories. It thus providesthe optimum solution for safe and reliable transport, efficientstorage, the perfect packaging solution and reliable protec-tion for your goods from external influences.
5
ZARGES Universal Containersan innovation spanning more than 50 years
ZARGESZARGES K470 series – in accordance with to ATA 300 standard
The entire K470 series has beeen successfully tested in
accordance with the international aviation standard ATA 300
(category I). This is official confirmation of its suitability for
use in conjunction with air cargo. Category I means that a
container must be capable of standing up to a minimum
of 100 service cycles (i.e. inbound and outward flight in each
case) in air freight operation. ZARGES commissioned the
well-known test laboratory, Dayton T. Brown from the USA
to carry out the corresponding test series.
The following criteria were investigated:
w Drop resistance: K470 cases were loaded with a weight
of 23 kg and dropped 280 times from a height of
76/92 cm. Afterwards the locks and hinges were still
functioning perfectly and the lid could be opened and
closed without any problems.w Imperviousness to spray: the cases were sprinkled with
100 litres of water over a period of one hour.w Stability: this included a vibration test where the
cases were loaded with a weight of 23 kg and placed
on a vibrating table for two hours.
7
ZARGES Universal Containers
6
ZARGES Universal Containers
ZARGESK470 Universal Container
2
3
4
6
8
9
10
11
12
14
15
16
17
18
19
20
21
23
24
25
22
1
5
7
13
9
ZARGES Universal ContainersK470 Universal Container – check out the benefits. That’s what you get with ZARGES.
8
ZARGES Universal Containers
ZARGESK470 Universal Container
ZARGESK470 Universal Container
Order No. See< No. Int. dimensions (L × W× H, approx. mm) Ext. dimensions (L × W× H, approx. mm) Contents (approx. l) Weight (approx. kg)
40 835 1 350 × 250 × 150 400 × 300 × 180 13 2,6
40 677 2 350 × 250 × 310 400 × 300 × 340 27 3,1
40 810 3 550 × 350 × 150 600 × 400 × 180 29 4,2
40 568 4 550 × 350 × 220 600 × 400 × 250 42 4,8
40 678 5 550 × 350 × 310 600 × 400 × 340 60 5,0
40 564 6 550 × 350 × 380 600 × 400 × 410 73 5,3
40 849 7 550 × 550 × 220 600 × 600 × 250 67 5,6
40 859 8 550 × 550 × 380 600 × 600 × 410 115 6,6
40 836 9 550 × 550 × 580 600 × 600 × 610 175 7,8
40 837 10 600 × 430 × 450 650 × 480 × 480 116 6,5
40 838 11 600 × 560 × 300 650 × 610 × 330 101 6,5
40 839 12 600 × 560 × 440 650 × 610 × 470 148 7,4
40 840 13 660 × 600 × 350 710 × 650 × 380 143 7,6
40 841 14 690 × 460 × 380 740 × 510 × 410 121 6,9
40 842 15 690 × 640 × 340 740 × 690 × 370 150 8,0
40 843 16 690 × 640 × 430 740 × 690 × 460 190 8,6
40 565 17 750 × 550 × 380 800 × 600 × 410 157 10,0
40 566 18 750 × 550 × 580 800 × 600 × 610 240 12,0
40 844 19 780 × 480 × 520 830 × 530 × 550 182 11,1
40 845 20 900 × 480 × 400 950 × 530 × 430 164 11,0
40 846 21 900 × 640 × 450 950 × 690 × 480 243 13,4
40 567 22 950 × 450 × 380 1000 × 500 × 410 162 10,9
40 580 23 1150 × 750 × 480 1200 × 800 × 510 415 20,0
40 875 24 1550 × 550 × 465 1600 × 600 × 495 396 25,0
40 876 25 1650 × 750 × 670 1700 × 800 × 700 829 30,0
NB: Inside clearance approx. 30 mm less than internal measurement (length and width). For other sizes please enquire. Available accessories: divider sets, attaché tool inserts, foam sets, dolly trolleys, snap on castors, trolleys and pallets – please enquire.
Important Note:K470 transport container for trans-
porting hazardous goods can be
supplied at extra cost. Please quote
GGVS specification when ordering.
Special internal inserts available
on request.
Ordering example: 40 564 GGVS.
*Inspected:
Composite packaging UN 4B
Individual solutions to individual problems. Any logis-tical problem calls for its own particular solution. This has always been a governing principle of our work.And, of course, this is especially so in cases where our broad standard range is not sufficient on its own. In close co-operation with our customers we changedimensions, internal and external fittings, the designor the colour of the K 470 and make precise adaptationsto suit the relevant requirements. Why not speak to usabout it?
Special features K470.w Order Nos. 40 677 and 40 835 are fitted with: 1 drop-type
handle on the lid, corner beading, 1 snaplock in the centre of
the container.w Order Nos. 40 810 (no beading) and 40 849 (with beading) are
fitted with: 1 handle on the front between the snaplocks.w Order Nos. 40 580, 40 875 and 40 876 are fitted with:
2 each skids made from extruded aluminium on lid and floor,
3 snaplocks on front and 2 drop-type handles at each end.w Order No. 40 568 is fitted with an additional handle
on the front.
11
ZARGES Universal ContainersIndividual Solutions for Individual Applications
ZARGESK470 Universal Container
10
ZARGES Universal ContainersIndividual Solutions for Individual Applications
ZARGESK470 Universal Container
13
ZARGES Universal ContainersDetails
12
ZARGES Universal ContainersK470 Universal Container – check out the benefits. That’s what you get with ZARGES.
Stacking corners in cast aluminium.
w When faced with a choice, you start by considering the little things.Quality invariably shows in the detail.
And this is precisely why our universal containers have made us not only the market leader,
but the leader in terms of quality.
All-round seal incorporated in the lid. Protected against wear and tear, overloading
and squashing.
Seal also guaranteed in the corners
(special notches).
Stainless steel hinge strips riveted to the
sheet metal outer covering and the solid profile lid
(to prevent them being ripped out).
Skid bars in robust aluminium profile on
the top of containers with external dimensions
of 1200 × 800 mm and above (additional lid
reinforcement).
Edge, base and lid profile framework in solid
profile, fully welded with sheet metal providing
a strong and durable joint.
Snap fasteners and hooks in aluminium/stainlesssteel, corrosion-resistant and with provision for
lead seal, padlock or quick-lock buckle closures.
(shackle thickness 6 mm �).
2 heavy-duty lid straps, sealed at the ends
to prevent fraying. Straps securely held with no
risk of tearing under heavy loads. Secured
with special large-headed rivets.
High-performance flash butt welding process in
accordance with DIN EN ISO 4063. This intensive
manufacturing process ensures a high degree of
stability and strength.
Heavy-duty ergonomic drop handles with returning spring (stainless steel)
and plastic sleeve.
Extremely strong, smooth, visually appealing
spot welds in accordance with DIN ISO 4063.
The overlap joint in the sheet metal outer covering
has no fissures and is extremely durable.
All-round beading and corner beading for reinforcement.
All riveted joints have solid rivets.
Skid bars in robust aluminium profile on containers
with external dimensions of 1200 × 800 mm and above
(additional base reinforcement).
15
ZARGES Universal Container – Accessories
14
ZARGES Universal Container – Accessories
ZARGESK470 Universal Container
New Perspectives for tried-and-tested Boxes
Nowadays flexibility is one of the most important pre-requi-sites when it comes to successful business. With our range ofaccessories we ensure that you will be able to react quicklyto new requirements without needing to replace your tried-and-tested ZARGES boxes entirely. From different codingoptions right through to variable internal fittings and match-ing rollers for easy transportability, you will find everythinghere that you need to adapt your boxes so that they meet thecurrent requirement at any time. This ensures a high levelof protection for your investment and maximum provision forthe future.
Attaché insert
w Made from hardwearing woven fabric. The practical
briefcase for documents and work tools. w Dimensions: 430 × 290 mm.
w Order No. 40 626
Tool Pocket
w Removable, made from hard-wearing woven fabric.
A transportable storage bag for tools. w Dimensions: 435 × 260 mm.
w Order No. 40 627
Armoured Clasps
w Suitable for seal or
shackle lock.
w For using locks
with 8 mm shackle
diameter.
Label Holders
w Available in
various sizes to DIN
or in special sizes.
Self-adhesive labels
w in various sizes/colours/fonts, resistant to peeling
if required.
Labels
w For affixing to
containers, stamped
in DIN fonts, capital
letters 20 mm tall,
covering one or more
lines.
Lettering
w In DIN fonts, capital
letters, 20 mm high,
covering one or
more lines.
Standard Padded Inserts
w Foam insert, can be
adapted to accommodate
bottles 40 to 100 mm �.w Integrated absorbent
material. w Please enquire.
Divider System
w Made from high quality foams.w Includes base foam and foam with
raised finish in the lid.w The individual organization
system for larger items. w Size: 550 × 350 × 190 mm.
w Order No. 40 730
Adjustable Divider System
w Consisting of
a divider with two
notched strips.
w Set 1: Order No. 40 864w Set 2: Order No. 40 865w Set 3: Order No. 40 866
Security Keys
w Also available as master key
system.
Lock Set
w To suit all containers with lock
fittings in hinged closures. w Consists of 2 locks and 2 keys.
w One key operates all locks within
the set only.
Order No. 40 830w One key operates all locks within
the entire series.
Order No. 40 831
Shackle lock
w Shackle lock with 4-digit,
freely selectable combination
of numbers.w Shackle diameter 5 mm.w To fit all ZARGES containers and
P472 cases.
w Order No. 46 989
Co
nte
nts
no
t su
pp
lie
d.
Co
nte
nts
no
t su
pp
lie
d.
17
ZARGES Universal Container – Accessories
16
ZARGES Universal Container – Accessories
Accessories for K470 and K450 transport containers
Order No. Description To suit:
40 626 Attaché Case All K 470 and K 450 with the exception of Order No. 40 677 and 40 720
40 627 Tool Pocket All K 470 and K 450 with the exception of Order No. 40 677, 40 835 and 40 720
40 730 Divider Set K 470 and K 450 with internal dimensions 550 × 350 mm
40 735 Pick’n Pluck Foam Set 1 K 470 and K 450 with internal dimensions 550 × 350 mm
40 736 Pick’n Pluck Foam Set 2 K 470 and K 450 with internal dimensions 750 × 550 mm
40 741 Clip-On fixed Castors All K 470 and K450 from size 550 x 350 mm upwards
40 742 Clip-On swivel Castors All K 470 and K450 from size 550 x 350 mm upwards
40 864 Aluminium Divider Set 1 Panel height 215 mm, to fit containers with an internal width of 350 mm
40 865 Aluminium Divider Set 2 Panel height 350 mm, to fit containers with an internal width of 350 mm
40 866 Aluminium Divider Set 3 Panel height 345 mm, to fit containers with internal width of 450 mm
40 738 Transportation Rollers All K 470 and K 450 particularly suitable for those with an external length of 800 –1000 mm
40 739 Trolley, detachable All K 470 and K 450 with a length of 600 – 800 mm
40 830 Lock Set Interchangeable only within the set, To suit all containers with lock fittings
40 831 Lock Set Entire series interchangeable, To suit all containers with lock fitting Co
nte
nts
no
t su
pp
lie
d.
Co
nte
nts
no
t su
pp
lie
d.
Individual foam inserts
w We manufacture customised padded inserts from a
wide range of materials which, in terms of protection
and functionality, are perfectly coordinated with the
goods you wish to transport. w One of the special features of these first-class foams
is the fact that the protective effect of the finished
packaging can be calculated in advance.w Taking into account weight, area, height of drop and
sensitivity (G value) we develop packaging for you
featuring optimum padding thickness. The result is
maximum protection with minimum raw materials
usage. w If required, antistatic fittings and dissipative inserts
are also available.
Pick ’n Pluck Foam Set
Foam linings
w Pre-punched soft foam inserts made from open-cell
PU foam, the fast and cost-effective solution for
individual pieces or low-volume batch production.
Sheet thicknesses in set, 2 each 30 mm and 60 mm,
30 mm lid insert foam with raised finish, base foam
10 mm. Includes adhesive. Shape can be modified
without the need for special tools.
w Set 1: 550 × 350 × 220 mm.
Order No. 40 735To fit K470/K450 containers with internal dimensions 550 × 350 mm
w Set 2: 750 × 550 × 220 mm.
Order No. 40 736To fit K470/K450 containerswith internal dimensions 750 × 550 mm
w If required, we can supply the containers complete with
a durable and abrasion-resist-
ant PE foam lining. Floor and
side panels made from Plasta-
zote LD 45 (weight per unit
volume 45 kg/m3, thickness
11 mm), lid lined with
raised finish PU foam.
w For other materials
and side panel thick-
nesses please enquire.
Snap-on castors
w Made from high quality
polyamide, load capacity
up to 50 kg, supplied
inclusive of necessary
fixings and instructions
for assembly, easy to fit.
w Order No. 40 738To fit K 470 and K 450.Ideal for containers
with an external length
of 800 – 1000 mm.
Clip-On Castors
w These ZARGES Clip-On castors make all K470 and
K450 universal containers, from size 550 × 350
mm (L × W) internal measurements upwards,
mobile in just a few moments without the need for
tools.w Made from solid rubber, wheel diameter
100 mm, braked swivel castors, carrying
capacity 90 kg with 4 castors.w 2 fixed castors, Order No. 40 741
(each with clamping mechanism,
one left and one right).w 2 swivel castors, Order No. 40 742
(each with clamping mechanism,
one left and one right)
Pallet Base
w If required, the containers can be supplied with a
pallet base. Pallets in wood, plastic or aluminium.
Please enquire.
Trolley
w Simple self-assembly, smooth-running underbody,
54 mm � castors, load capacity 30 kg, extendable
handle can be locked in position.
w Order No. 40 739To fit K 470 and K 450 with an external length
of 600 – 800 mm.
w Supplementary set enables trolley to be used
on other boxes.
Order No. 40 740
NEW!
The following castor arrange-ments are recommended: w 2 swivel and 2 fixed castors
(1 × Order No. 40 742,
1 × Order No. 40 741)
w 4 swivel castors
(2 × Order No. 40 742)
19
Toolbox and Rollbox
18
K 450 Containers
Co
nte
nts
no
t su
pp
lie
d.
w High-strength, corrosion-resistant
aluminium alloy.w Stainless steel hinges.w Lid seal for protection against dust and spray.w Stabilising corner beading.w Stirrup hinges with provision for lock.w Can be secured by means of key,
lead seal or padlock.w Stackable, with grey plastic stacking corners
ensuring high load capability.w To suit pallet dimensions to DIN 15141.
ZARGESK450 Containers
1
2
3
4
5
6
7
Order See Int. dimensions Ext. dimensions Contents WeightNo. No. (L × W × H, approx. mm) (L × W × H, approx. mm) (approx. l) (approx. kg)
40 720 1 350 × 250 × 310 400 × 300 × 340 27 3.0
40 721 2 550 × 350 × 220 600 × 400 × 250 42 4.7
40 722 3 550 × 350 × 310 600 × 400 × 340 60 4.9
40 723 4 550 × 350 × 380 600 × 400 × 410 70 5.2
40 724 5 750 × 350 × 310 800 × 400 × 340 81 6.1
40 725 6 750 × 550 × 380 800 × 600 × 410 155 7.5
40 716 7 750 × 550 × 580 800 × 600 × 610 240 8.9
NB: Inside clearance approx. 30 mm less than internal measurement(length and width).
Accessoriesw Small parts container with 21 insert sections in PP.
The sorting system for smaller items.
To suit K450 Order-Nos. 40 721 to 40 724.w Size: 430 × 330 × 60 mm
Order No. 40 628w For further accessories see pages 14/15.
Co
nte
nts
no
t su
pp
lie
d.
w Fold-down front section.w 5 plastic pull-out internal compartments and
one larger compartment.w 2 stirrup latchese.w Broad band-type hinge.w Corners fitted to protect against impact.w Flexible handle for carrying.
ZARGESToolbox
w One end fitted with 2 wheels.w Robust and retains its shape.w Protected against dust and spray.w Secure, central stackable.w Stirrup hinges adaptable for lead seals,
shackle and key-operated locks.w Sprung, drop-type handles.
ZARGESK412 Rollbox
Order No. Int. dimensions Ext. dimensions Contents Weight(L × W × H, approx. mm) (L × W × H, approx. mm) (approx. l) (approx. kg)
40 851 910 × 365 × 375 950 × 400 × 410 124 8.7
40 852 740 × 365 × 375 780 × 400 × 410 100 7.6
NB: Inside clearance on Rollboxes approx. 40 mm less than internal measure-ment (length and width). For other sizes please enquire.
Order No. Int. dimensions Ext. dimensions Weight(L × W × H, approx. mm) (L × W × H, approx. mm) (approx. kg)
40 758 410 × 250 × 230 445 × 260 × 255 3.2
Accessories
Set of Locks with Keys:
Order No. 40 830Order No. 40 831
Shackle-type Lock:Order No. 46 989
w see page 15.
20
K410 Alu-Case
w Light alloy cases with smooth, anodised surfaces.w Corrosion-resistant.w Corner reinforcements with corner pieces to cases.w Comfortable carrying handle.w Turnbuckles with involuntary release safeguard.w Watertight base section.w Hinged lid with peripheral seal ensures extensive
protection against dust and spray.w Can be fitted with various foam inserts.
ZARGESK410 Alu-Case
Co
nte
nts
no
t su
pp
lie
d.
21
Service and Attaché CasesThe elegant transport option
The robust ZARGES aluminium cases representan ideal transport and packaging medium for awide range of applications. Ideal for presentingsamples, as secure packaging for valuable or sensitive items or for carrying the serviceengineer’s repair kit.
Robust, lockable and fitted with ergonomiccarrying handles, they are characterised byfunctionality, long life and timeless design.
Order No. See Int. dimensions Ext. dimensions Contents WeightNo. (L × W × H, approx. mm) (L × W × H, approx. mm) (approx. l) (approx. kg)
40 765 1 360 × 300 × 140 370 × 330 × 145 15 1.8
40 763 2 470 × 350 × 120 480 × 380 × 125 20 2.2
40 764 3 530 × 330 × 140 540 × 360 × 145 25 2.5
40 766 4 470 × 350 × 170 480 × 380 × 175 28 2.7
NB: Inside clearance approx. 20 mm less than internal measurement (lengthand width). For other sizes please enquire.
Internal Fittings Type AOrder No. To fit Foam sheet thickness
Alu-Case Order No. (lower section)
41 704 40 763 2 × 20 mm 1 × 40 mm
41 705 40 764 2 × 40 mm 1 × 20 mm
41 706 40 766 3 × 40 mm 1 × 20 mm
Internal Fittings Type BOrder No. To fit
Alu-Case Order No.
41 701 40 763
41 702 40 764
41 703 40 766
Internal Fittings Type B
w Lid: self-adhesive, stone grey burl foam sheet,
20 mm thick.w Base section: self-adhesive foam slotted framework,
plastic sheet for compartments can be divided
up as required, universally adjustable.w One set consists of: burled lid sheet, smooth base
sheet 20 mm thick, 2 notched longitudinal and
2 notched end pieces, 1 horizontal divider (notched)
and 2 smooth lengthwise dividers (can be cut to suit
by customer).
Internal Fittings Type A
w Lid: Self-adhesive, stone grey burl foam sheet,
20 mm thick.w Base section: removable foam sheets in varying
thicknesses with good padding effect.w Depending on requirement, cut out using
a sharp knife.
Accessories Internal Fittings Typ BOrder No. To fit
Alu-Case Order No.
Crosswise notched divider panel 309 580 40 763
309 581 40 764
309 582 40 766
Smooth divider panel309 583 40 763
309 584 40 764
309 585 40 766
Typ A
Typ B
Important Note:The aluminium cases for transportation of Hazardous Goods are subject
to an extra charge. Please quote GGVS specification when ordering. Special
internal inserts available on request. Ordering example: 40 766 GGVS.
*Inspected: Composite packaging UN 4B
1
23
4
ZARGESService and Attaché Cases
Ensuring you always make a good impression.
w Anodised aluminium alloy shell.w Broad band hinge.w Plastic impact strips.w Rubber seal for protection against dust and spray.w Comfortable carrying handle and two locks
with anti-spring back feature.
Attaché case also available with:w Digital lock, fabric lining, attaché compartment
and lid retainer.
Co
nte
nts
no
t su
pp
lie
d.
w Set 3:
650 × 455 × 180 mm.
Order No. 41 712To fit Service Case:40 874
Pick ’n Pluck Foam Setw Set 1:
490 × 330 × 120 mm.
Order No. 41 710To fit Service Case:40 873
w Set 2:
490 × 330 × 150 mm.
Order No. 41 711To fit Service Case:40 872
Toolbagw Size : 435 × 260 mm.
Order No. 40 627
To fit Service Cases:40 872 to 40 874
Attaché Case Insert:w Size : 430 × 290 mm.
Order No. 40 626
To fit Service Cases:40 872 to 40 874
Accessories: Case inserts
Service CaseOrder No. Int. dimensions Ext. dimensions Contents Weight
(L × W × H, approx. mm) (L × W × H, approx. mm) (approx. l) (approx. kg)
40 873 490 × 330 × 130 505 × 365 × 130 20 2.8
(90/40)* (90/40)*
40 872 490 × 330 × 160 505 × 365 × 160 24 2.9
(90/70)* (90/70)*
40 874 650 × 455 × 190 665 × 490 × 190 55 4.5
(120/70)* (120/70)*
Attaché CaseOrder No. Int. dimensions Ext. dimensions Contents Weight
(L × W × H, approx. mm) (L × W × H, approx. mm) (approx. l) (approx. kg)
41 841 490 × 330 × 130 505 × 365 × 135 20 3.1
(90/40)* (90/40)*
* Height (H) split into lower and upper section.
Order No. 40 874
Order No. 41 841
Order No. 40 872
Order No. 40 873
23
P472 CaseThe case that knows no limits.
22
P472 CaseThe case that knows no limits.
Accessories:w Pick ’n Pluck foam set made from pre-punched PU foam.w Set of divider panels, padded, divider panels secured
in place with Velcro-type fastening, adjustable.w Foam fittings, manufactured to individual customer
requirements. Just ask us.w Lid insert for enhanced organizational capacity.w Combination lock, Order No. 46 989w Dessicant, Order No. 46 988w Customer-specific inscriptions to your specification
on request.
The ZARGES hard shell case for maximum protection of sensitive goods.
w Indestructible, stackable, rigid case manufactured
from high grade polypropylene.w Ideal transit and storage case for fragile goods
such as electronic, optical and measuring instruments,
equipment for medical and biotechnology applications,
etc.w Available in more than 30 different styles and sizes,
with internal capacities to 227 litres.w Larger cases with wheels and retractable handles
for easier handling.w Neoprene seal for watertightness and airtightness
to IP 67.w Pressure relief valve as standard.w Temperature resistant from –23 °C to +99 °C, and
resistant to many aggressive chemicals such as
acids and alkalis.w All metal parts on handles and catches are
non-corroding.w Standard in black, but other colours (yellow, silver,
sand, olive green and orange) are available according
to model in minimum order quantities. Other colours
on request
w Certificates:• Air Transportation Association.
• US military standards MIL-C-4150 J.
• NATO (issued stock numbers).
Model 1620
Model 1510
Model 1450
Model 1490 CC1
Model 1150
Model 1120Model 1720
Model 1300
Model 1400
Model 1450
with frame insert
w Note:Please see also the catalogue:
PELI CASES, Order No. 240.
P472 – Model 1620 complete with trolley
Divider set Pluck foam set
ZARGESP472 Case
Order No. Order No. Order No. Model Int. dimensions Ext. dimensions Contents Weight without empty with foam with divider (L × W× H, approx. mm) (L × W× H, approx. mm) (approx. l) Inlet (approx. kg)
46 800 46 801 – 1120 187 × 124 × 77 209 × 166 × 90 1,8 0,5
46 810 46 811 – 1150 212 × 149 × 93 235 × 192 × 111 2,9 0,8
46 820 46 821 – 1200 238 × 184 × 103 270 × 246 × 123 4,5 1,2
46 830 46 831 – 1300 238 × 184 × 155 270 × 246 × 174 6,8 1,4
46 840 46 841 – 1400 305 × 230 × 131 340 × 295 × 152 9,2 1,8
46 730 46 731 46 732 1430 344 × 146 × 297 430 × 244 × 341 18,0 3,0
46 720 46 721 46 722 1440 * 434 × 190 × 406 500 × 305 × 457 33,6 6,6
46 850 46 851 46 852 1450 376 × 263 × 152 406 × 330 × 174 15,0 2,5
46 860 46 861 – 1470 400 × 268 × 95 424 × 332 × 111 10,2 1,7
46 880 46 881 – 1490 454 × 292 × 105 494 × 354 × 119 13,9 2,3
46 882 – – 1490 CC1 454 × 292 × 105 494 × 354 × 119 13,9 2,3
With laptop fittings, shoulder strap, lockable catches.
46 700 46 701 – 1495 479 × 333 × 97 549 × 438 × 124 15,5 3,3
46 890 46 891 46 892 1500 432 × 290 × 155 470 × 357 × 176 19,4 2,9
46 770 46 771 46 772 1510 * 514 × 289 × 193 559 × 351 × 229 28,6 5,1
46 900 46 901 – 1520 454 × 324 × 171 486 × 392 × 192 25,2 3,6
46 910 46 911 46 912 1550 481 × 367 × 197 525 × 436 × 217 34,8 4,8
46 790 46 791 46 792 1560 * 518 × 392 × 229 560 × 455 × 265 46,5 6,9
46 920 46 921 46 922 1600 552 × 427 × 200 616 × 494 × 220 47,1 5,9
46 930 46 931 46 932 1610 * 563 × 435 × 269 624 × 490 × 303 65,9 9,1
46 940 46 941 46 942 1620 * 560 × 432 × 320 630 × 492 × 352 77,4 11,1
46 680 46 681 46 682 1630 * 703 × 533 × 394 794 × 615 × 444 147,0 14,1
46 710 46 711 46 712 1640 * 602 × 610 × 353 691 × 699 × 414 130,0 15,4
46 950 46 951 46 952 1650 * 736 × 454 × 267 781 × 520 × 295 89,2 13,3
46 980 46 981 46 982 1660 * 740 × 525 × 448 800 × 581 × 479 174,0 15,5
46 690 46 691 46 692 1690 * 762 × 635 × 463 847 × 722 × 463 197,0 15,4
46 740 46 741 46 742 0340 457 × 457 × 445 518 × 519 × 489 93,0 10,9
46 750 46 751 46 752 0350 ** 508 × 508 × 409 569 × 571 × 540 118,0 11,8
46 760 46 761 46 762 0370 ** 610 × 610 × 610 673 × 673 × 642 227,0 14,5
46 960 46 961 – 1700 * 910 × 351 × 133 968 × 452 × 155 42,5 7,3
46 780 46 781 – 1720 * 1067 × 343 × 133 1127 × 406 × 156 48,6 7,6
46 970 46 971 – 1750 * 1283 × 341 × 133 1346 × 443 ×154 58,2 10,7
NB: The models marked * are fitted with wheels for easier handling. Models 1440, 1510, 1560, 1610, 1620, 1630, 1650, 1660 and 1690 also have a retractablehandle. Standard colour black, other colours available on request. Model 0340 with 4 castors and a pull handle. Frame insert can be supplied for a number ofmodels from 1120 to 1550.
** Matching set of add-on castors (2 fixed and 2 swivel castors) available, Order No. 46 757 (not included in delivery).
25
Retou ® Collapsible Box
24
P402 CasePlastic Case made from ABS
w Robust case injection moulded from ABS (acrylonitrile-
butadiene-styrene) or SB (styrene-butadiene).w High impact resistance and surface hardness
(resists scratching).w Unbreakable and retains its shape with
low intrinsic weight.w Stackable and palletisable.w Ergonomic carrying handle.w Soft Click locks.w Temperature resistant from –30 °C to + 80 °C.w UV-resistant and cadmium-free.w The case material ABS is environmentally friendly
and 100 % recyclable.w Optimum case volume utilization as a result
of split 1/4 lid, 3/4 lower section. w Suitable for foam inserts.
w These cases offer extensive possibilities for protecting
your product inside the case, in the shape of foam
fittings, thermoformed inserts or cover sheets. w Individual forming options using screen printing,
hot embossing or in-mould labelling. w ABS injection moulded cases made from Plaston
have proved themselves thousands of times over
in demanding every-day applications.
ZARGESP402 Case
Typ Order No. Order No. Order No. Int. dimensions Ext. dimensions Volumen Weightblack blue red (L × W × H, approx. mm) (L × W × H, approx. mm) approx. l approx. kg
Typ 31 43 752 43 753 43 754 384 × 219 × 47 + 17 384 × 290 × 71 5,1 0.85
Typ 51 43 755 43 756 43 757 372 × 249 × 66 + 17 394 × 293 × 91 7,7 1.08
Typ 81 43 758 43 759 43 760 420 × 276 × 78 + 22 444 × 320 × 108 11,6 1.30
Typ 111 43 761 43 762 43 763 440 × 310 × 78 + 22 464 × 354 × 108 13,6 1.50
Typ 126 43 764 43 765 43 766 530 × 375 × 95 + 35 557 × 422 × 139 25,8 2.50
Typ 146 43 767 43 768 43 769 609 × 409 × 90 + 51 639 × 466 × 151 35,1 3.50
Typ 156 43 770 43 771 43 772 609 × 409 × 150 + 51 639 × 466 × 211 50,0 3.90
w Collapsible reusable packaging made from aluminium alloy.w Can be folded up by one person quickly and easily.w Ease of handling thanks to interlocking sections with
retention pins to base and side sections.w Profiled protective strips.w 3 solid panel sections providing a high level of stability.w Collapsability feature means that the space requirement
is reduced to one thirdw Lid firmly connected to rear panel by means of
anti-vibration hinge.w End sections and lids feature additional external
reinforcement profiles.w Automatic engagement locks, can be lead sealed or
reinforced with shackle-type lock.w Stacking corners.w Can be used on moving belts.w 15 mm space when collapsed (for e.g. internal lining).
ZARGESRetou ® Collapsible Box
w The packaging system for the transport and storage of liquid
and highly viscous substances.w Very high level of quality and hygiene with minimum outlay
on cleaning.w Collapsible containers made from light alloy.w Can be easily folded flat by one person.w Stacking corners.w Stackable up to 3 at a time when full, up to 7 at a time when
folded flat.w Suitable for roller conveyorsw Run-off opening integrated in side panel/pallet.w Accessories such as inliners, filling and emptying bung etc.
appropriate to contents and the purpose for which the item
is to be used. Please enquire. w Matching dolly trolley on p. 30.w Can also be used in clean rooms and to cater for special
hygiene requirements.w Can be used in the foodstuffs, cosmetics and pharmaceuticals
industries, industrial chemistry and biochemical applications.
ZARGESRetou ® collapsible container for inliners
Retou ® Collapsible BoxOrder No. Int. dimensions Ext. dimensions Height folded Contents Weight
(L × W × H, approx. mm) (L × W × H, approx. mm) (approx. mm) (approx. l) (approx. kg)
45 070 730 × 530 × 570 800 × 600 × 600 145 221 21.0
45 073 1130 × 730 × 740 1200 × 800 × 900 287 610 62.0
NB: The aluminium pallet and aluminium impact protection strips are special fittings. Supplied with wooden pallet and wooden impact protectionstrips. Order No. 45 073: dimensions and weight including flat wooden pallet. Other sizes on request.
Collapsible Box – Special FeaturesOrder No. Detailed description
45 070 + 45 073 Lengthwise front panel can be folded down
loading also possible from the front
45 073 flat wooden pallet supplied as standard
Order No. Int. dimensions Ext. dimensions Height folded Contents Weight(L × W × H, approx. mm) (L × W × H, approx. mm) (approx. mm) (approx. l) (approx. kg)
45 075 730 × 530 × 570 800 × 600 × 750 260 200 26.0
45 076 1145 × 745 × 590 1200 × 800 × 820 400 500 60.0
45 077 1145 × 945 × 930 1200 × 1000 × 1140 400 1000 75.0
w Protection type IP 65 to DIN 40 050 and ICE 34-5/529
using welded housing and lid with peripheral seal.w Base with stacking bars, top plate features recesses
for stacking.w All sizes can be stacked with other sizes
(with the exception of depth 610).w Inside frame made from aluminium extrusions
suspended by shock mounts.w Sides with countersunk drop-type sprung handles.w All sides and top sections with reinforcing ribs
(with the exception of depth 610).w Rubber mounts with rails to accommodate anti-
vibration framework.w Fully removable framework.w Top section with rapid release fasteners.w Variable designs featuring different depths
and heights.w Wide range of special fittings for numerous
applications.w Can be fitted into Dornier Shelter framework.w Can also be supplied as UN approved
hazardous goods packaging.
27
Mitraset® 19˝Electronic Housings
ZARGESMitraset® 19˝Electronic Housings
Mitraset® 19˝Electronic Housings to VG 95446 aredesigned to accommodate electronics equipment in a19˝rack. They fulfil a number of protective functions:for instance, deflection of mechanical stresses suchas impact, shock and vibrations, protection againstelectromagnetic interference such as radio waves,lightning strikes etc. as well as from general environ-mental influences such as heat, moisture, dust etc. In order to fulfil these requirements Mitraset® 19˝Electronic Housings are constructed as follows: Thecasing is constructed of precision welded high tensilealuminium sheets to which an elastically suspendedanti-vibration frame, made from extrusions, is fitted.The actual device to be protected is inserted into thisframework and screwed in. The anti-vibration frame-work is linked to the casing by means of rails and rub-ber shock mounts, the type of bearing and the materialused are selected to suit the relevant requirements.
w Note:Please also see our special catalogue:
Hi-Tech containers, Order No. 254.
26
K475 Transport and Storage Container
Co
nte
nts
no
t su
pp
lie
d.
w Moisture-resistant special reusable packaging.w Particularly suitable for high-quality equipment.w Stackable, with stacking corners to base and lid sections.w Removable lid with peripheral seal.w Stirrup hinges with spring catch.w Sprung, drop-type handles, ergonomic and with
high load-carrying capability.w Pressure compensating valve and moisture indicator.w Can also be supplied in special sizes.w Interior fittings (e.g. foam padding) and special screen
arrangements available.
HF-sealed version also available on request.
ZARGESK475 Transport and Storage Container
w Note:Please see also
our special catalogues:
Hi-Tech Containers,
Order No. 254.Hazardous Goods Pack-
aging, Order No. 260.
Important Note:The K475 Transport Container for
transportation of Hazardous Goods
are subject to an extra charge.
Please quote GGVS specification
when ordering. Special internal
inserts available on request.
Ordering example: 45 133 GGVS.
*Inspected:
Composite packaging UN 4B
1
8
Order See Int. dimensions Ext. dimensions Contents WeightNo. Nr. (L × W× H, approx. mm) (L × W× H, approx. mm) (approx. l) (approx. kg)
45 131 1 360 × 260 × 265 400 × 300 × 300 25 4.8
45 133 2 360 × 360 × 265 400 × 400 × 300 34 5.5
45 137 3 560 × 360 × 265 600 × 400 × 300 53 7.1
45 138 4 560 × 360 × 365 600 × 400 × 400 74 7.8
45 141 5 760 × 360 × 265 800 × 400 × 300 73 10.7
45 142 6 760 × 360 × 365 800 × 400 × 400 100 11.8
45 144 7 760 × 560 × 360 800 × 600 × 400 153 15.1
45 145 8 760 × 560 × 460 800 × 600 × 500 196 16.8
45 146 9 760 × 560 × 560 800 × 600 × 600 238 18.5
NB: Inside clearance on K475 containers is approx. 32 mm less than the internalmeasurement (length and width). Other sizes on request.
5
6
9
3
7
28
Flat Pallets
Aluminium flat pallet with 4 corner-mounted feet(see o. 1)
w Framework and lengthwise slats made from closed,
high-strength, corrosion-resistant light alloy sections.w Seams welded to ensure watertight finish.
ZARGESFlat Pallets
29
Baskets and Containers
ZARGES pallets are characterised by their high level of stability andload-carrying capability as well as their resistance to corrosion andtheir long life. Fabricated from high-quality materials and carefullymachined, they are extremely hygienic, easy to clean and GMPapproved. Whether they are made from aluminium or stainlesssteel, whether they are fitted with cornermounted feet or with skids,ZARGES pallets invariably represent a long-term commercialinvestment – resistant to aggressive substances, heat, cold andmechanical damage. Special versions available on request.
1500kg
1
2
3
4
Order No. Dimensions No. of slats Weight Load capacity(L × W × H, approx. mm) (approx. kg) (approx. kg)
45 162 800 × 600 × 150 3 8.5 600
45 172 1200 × 800 × 150 4 13.0 600
45 182 1200 × 1000 × 150 5 15.0 600
Aluminium flat pallet with long corner-mounted feet (see no. 2)
w Framework and lengthwise slats made from closed,
high-strength, corrosion-resistant light alloy profiles.
Seams welded to ensure watertight finish.w Extra long corner-mounted feet (L = 300 mm) combine the
advantages of skid-type undercarriage and corner-mounted
feet. They can, for example, be used on moving belts and are
suitable for automatic warehousing applications.w Plenty of room for fork lift truck access. No solid section
to get in the way, therefore less risk of damage.
Order No. Dimensions No. of slats Weight Load capacity(L × W × H, approx. mm) (approx. kg) (approx. kg)
45 175 1200 × 800 × 150 4 14.0 1000
45 185 1200 × 1000 × 150 5 16.5 1000
Aluminium flat pallet with skids (see no. 3)
w Framework and horizontal slats made from closed,
high-strength, corrosion-resistant light alloy profiles.
w Central support for skids.w Seams welded to ensure watertight finish.w Can be used on moving belts.
Aluminium flat pallet with skids and corner-mounted feet(see no. 4)
w Framework and horizontal slats made from closed,
high-strength, corrosion-resistant light alloy sections.w Centre support skids and 4 corner feet.w Seams welded to ensure watertight finish.w Suitable for use on moving belts.
Order No. Dimensions No. of slats Weight Load capacity(L × W × H, approx. mm) (approx. kg) (approx. kg)
45 173 1200 × 800 × 150 5 12.8 1000
45 183 1200 × 1000 × 150 5 14.6 1000
Order No. Dimensions No. of slats Weight Load capacity(L × W × H, approx. mm) (approx. kg) (approx. kg)
45 174 1200 × 800 × 150 6 15.2 1500
45 184 1200 × 1000 × 150 6 17.3 1500
ZARGESBasket
K270 Pharmaceuticals Transport Container
w Construction as for K270 transport container but anodised.w Sides and base smooth.w Welded side panel.w Drop-type handles.w Accessories: removable lid for use when stacking with
apertures for security seals.
ZARGESContainers
ZARGES perforated baskets are available in straight-sided and tapered sides versions. Straight-sidedbaskets can be stacked on top of each other whilst thetapered versions can be stacked one inside the other.
K250 Transport Basket
w Straight design.w Their robust stacking corners mean that they can be
stacked one on top of the other.w Slotted hand-grips to each end.w Plastic skids.
Order No. Int. dimensions Ext. dimensions Contents Weight(L × W × H, approx. mm) (L × W × H, approx. mm) (approx. l) (approx. kg)
40 781 540 × 340 × 280 580 × 380 × 300 52 2.5
40 782 700 × 440 × 280 740 × 480 × 300 86 3.5
K251 Transport Basket
w Tapered design.w Can be stacked one inside the other.w Slotted hand-grips at each end.w Plastic skids.
Order No. Int. dimensions Ext. dimensions Height Volumen Weight(L × W × H, approx. mm) (L × W × H, approx. mm) (approx. mm) (approx. l) (approx. kg)
40 783 top: 700 × 445 top: 740 × 485 290 89 3.0
bottom: 630 × 375 bottom: 640 × 380
ZARGES containers are a tried-and-tested transportmedium, packaging and efficient storage unit all inone. Individual models are also available which aresuitable for use on conveyors or moving belts.
Order No. Int. dimensions Ext. dimensions Contents Weight(L × W × H, approx. mm) (L × W × H, approx. mm) (approx. l) (approx. kg)
48 011 540 × 340 × 300 580 × 380 × 325 55 3.9
48 014 Container lid 0.6
Special sizes on request.
K270 Transport Container
w Solid edge and base profiles.w Beading and corner beading
(Order No. 40 551, 40 552, 40 554).w Slotted hand-grips to both ends.w Suitable for conveyors and moving belts.w Auto. coding strips on request.w Co-ordinated with DIN 15141 pallet sizes.
Order No. Int. dimensions Ext. dimensions Contents Weight(L × W × H, approx. mm) (L × W × H, approx. mm) (approx. l) (approx. kg)
40 551 720 × 540 × 400 760 × 580 × 425 155 5.3
40 552 720 × 540 × 300 760 × 580 × 325 117 4.6
40 553 720 × 540 × 200 760 × 580 × 225 77 4.2
40 554 540 × 340 × 300 580 × 380 × 325 55 3.0
40 555 540 × 340 × 200 580 × 380 × 225 37 2.5
W170 Trolley
w Robust light alloy trolley for a range of different applications.w High-tensile generously-proportioned extrusions to top rim
and base, positive interlocking ensures permanent bonding
to metal.w Ends and sides reinforced with peripheral beading
and corner beading.w Chassis: 2 fixed and 2 swivel action castors, corner mounted,
125 mm �, 40 mm wide, smooth-running, “non-marking”,
with roller bearings, thread guards.
31
Box Trolleys
ZARGESW170 Trolley
30
Dolly Trolleys
W150 Dolly Trolley
w Suitable for transporting K270 light alloy boxes
and/or K470/K450 cases.w Chassis: 2 fixed and 2 swivel-action castors,
125 mm �, 40 mm wide, smooth running, rubber tyres,
“non-marking”, roller bearings.
ZARGESDolly Trolleys
When it comes to finding a simple answer to“weighty”transport and storage problems, the manoeuvrableZARGES trolleys on castors are the automatic, cost-efficient solution.
Available in high or low level versions, they literallymake light work of handling and transporting ZARGESboxes, cases and baskets singly or stacked evenwhere heavy loads are involved.
W152 Dolly Trolley
w For transporting K250 light alloy baskets, K470/K450
cases and K270 boxes.w Chassis: 2 fixed and 2 swivel-action castors,
125 mm �, 40 mm wide, smooth running, rubber tyres,
“non-marking”, roller bearings.
Order No. To suit Container ext. dimensions Weight(L × W, approx. mm) (approx. kg)
40 608 K 270 760 × 580 5.5
40 607 K 270 580 × 380 5.1
40 608 K 470/K 450 800 × 600 5.5
40 607 K 470/K 450 600 × 400 5.1
or 2 cases: 400 × 300
Order No. To suit Ext. dimensions Height Weight(L × W, approx. mm) (approx. mm) (approx. kg)
40 609 K 250 580 × 380 450 5.9
740 × 480
40 680 K 470/K 450 800 × 600 450 6.2
K 270 760 × 580
Whether it is a matter of transporting items in-house,supplying goods to outlying departments, transportinglaundry, supplies or waste disposal, ZARGES box trolleys can be used for an extensive number of applications. A variety of models and a wide range of accessories turnZARGES box trolleys into multi-functional aids.
Special designs are available for particular applications.
W170 Trolley with Lid (accessory)
w Hinged lid.w Polyester straps.w 2 snaplocks.w Subject to an extra charge, the lid can be supplied complete
with aperture and security plate
Order No. Int. dimensions Ext. dimensions Contents Weight(L × W × H, approx. mm) (L × W × H, approx. mm) (approx. l) (approx. kg)
40 631 1000 × 640 × 650 1050 × 690 × 855 415 19.5
40 635 1250 × 700 × 750 1300 × 750 × 955 655 23.7
Order No. Hinged lid with strap and 2 snaplocksto fit order no.
40 654 40 631
40 675 40 635
327 412 40 631 with aperture
339 147 40 635 with aperture
ZARGESW154 heavy duty dolly trolley
w Welded extruded aluminium construction.w Castors (2 fixed and 2 braked swivel castors)
made from polyamide, white.
Order No. To suit Ext. dimensions Container Max. WeightOrder No. (L × W, approx. mm) load (approx. kg)
45 096 45 075/45 070 800 × 600 Up to 300 kg 7.8
45 097 45 076/45 073 1200 × 800 Up to 600 kg 15.9
40 580
33
Box Trolleys
32
Box Trolleys
W171 Box Trolley with Fold-down Section
Construction similar to W170 trolley, apart from the following:w Long side folds down to half its height for more
convenient loading and unloading.w Rear wall with central vertical reinforcement section.w Fold-down section with fixing for bolts and movable
hinges for mounting.w Corner-mounted castors.w Chassis: 2 fixed and 2 swivel action castors, corner-
mounted, 125 mm �, 40 mm wide, smooth-running,
“non-marking”, with roller bearings, thread guards.
ZARGESW171 Box Trolley
W171 trolley, anodised, with tri-sectional lid
Design similar to W 171 trolley, except for:w Smooth side panels without beading.w Straight seam-welded, peripheral floor joint sealw Tri-sectional lid fold-down mechanism and
one front panel flap. w Push-pull handle on swivel castor side.w Drain tap to trolley floor.w Peripheral plastic-padded deflector buffer.w Chassis: 2 fixed and 2 swivel castors in diamond
arrangement, � 200 mm, 50 mm wide, smooth
running, with rubber tyres, ”non-marking“, roller
bearings, thread guards.
Order No. Int. dimensions Ext. dimensions Contents Weight(L × W × H, approx. mm) (L × W × H, approx. mm) (approx. l) (approx. kg)
40 691 1000 × 575 × 1200 1140 × 685 × 1490 690 30.0
40 692 1250 × 700 × 1200 1390 × 810 × 1490 1050 35.0
40 693 Construction and dimensions as for Order No. 40 691 but without anodising.
40 694 Construction and dimensions as for Order No. 40 692 but without anodising.
Transport Container, mobile
w Reinforced with peripheral beading/ corner beading.w Push-Pull handle.w Extruded hinged lid with aperture approx. 420 × 24 mm
complete with security plate.w Stirrup hinge.w Chassis: axle tube with 2 castors, 200 mm �.
ZARGESTransport Container, mobile
Order No. Int. dimensions Overall width Contents Weight(L × W × H, approx. mm) (approx. mm) (approx. l) (approx. kg)
40 896 450 × 550 × 980 580 240 15.0
w One long side with cut-out section (approx. depth 295 mm).w Push-Pull handles to both ends.w High tensile extrusions to top rim and base.w Ends and sides reinforced with peripheral beading and
corner beading.w Chassis: 2 fixed and 2 swivel action castors, corner
mounted, 200 mm �, 50 mm wide, smooth running,
rubber tyres, “non-marking”, with roller bearings,
thread guards.
ZARGESW172 Trolley
w For transporting sensitive, lightweight articles.w Smooth internal walls.w High tensile extrusions to top rim and base.w Chassis: 2 fixed and 2 swivel action castors, corner-
mounted, 75 mm �, 25 mm wide, smooth-running,
rubber tyres, “non-marking”, with roller bearings,
thread guards.
ZARGESW181 Trolley
w Anodised and non-anodised versions.w Depending on the model, 16 discharge holes, 8 mm �,
located centrally in floor of trolley.w High tensile extrusions to top rim and base.w Ends and sides reinforced with peripheral beading
and corner beading.w Stackable.w Chassis: 2 fixed and 2 swivel action castors, corner-
mounted, 125 mm �, 40 mm wide, smooth-running,
rubber tyres, “non-marking”, with roller bearings,
thread guards.
ZARGESW182 Trolley
Order No. Int. dimensions Ext. dimensions Contents Weight(L × W× H, approx. mm) (L × W× H, approx. mm) (approx. l) (approx. kg)
40 661 (anodized) 700 × 560 x 590 740 × 600 × 760 230 12.0
complete with drainage
perforations to base
40 780 (non-anodized) 700 × 560 x 590 740 × 600 × 760 230 12.0
without floor
discharge holes
Order No. Int. dimensions Ext. dimensions Contents Weight(L × W× H, approx. mm) (L × W× H, approx. mm) (approx. l) (approx. kg)
40 650 760 × 400 × 500 800 × 440 × 625 150 8.0
Order No. Int. dimensions Ext. dimensions Contents Weight(L × W× H, approx. mm) (L × W× H, approx. mm) (approx. l) (approx. kg)
40 634 1500 × 900 × 700 1650 × 950 × 980 945 37.0
Order No. Hinged lid with strap and 2 snaplocks to fit order no
40 675 40 674
339 147 40 674 with aperture
40 559 40 633
40 558 40 633 with hooded lid and no locks
Order No. Int. dimensions Ext. dimensions Contents Weight(L × W × H, approx. mm) (L × W × H, approx. mm) (approx. l) (approx. kg)
40 633 900 × 500 × 780 950 × 550 × 980 350 20.0
40 674 1250 × 700 × 1200 1300 × 750 × 1400 1050 33.0
Fig. 1
Fig. 2
Fig. 3
34
Box Trolleys
ZARGESW161 Constant Load Level Trolley, anodised
35
Box Trolleys
w Floor with vertical movement facility which keeps the load permanently
at the same level. (Fig. 1)w Using interchangeable lifting elements, the load capacity can be varied
from 30 – 195 kg in increments of 15 kg, depending on the type of trolley.
(Fig. 2)w The floor will remain horizontal even if the load is distributed unevenly.
(Fig. 2)w Light alloy extruded profile reinforcement to top rim with abrasion-
resistant plastic cladding. (Fig. 3)w Chassis: 2 swivel action and 2 fixed castors in diamond pattern,
125 mm �, 40 mm wide, smooth-running, rubber tyres, “non-marking”,
with roller bearings, thread guards.w Order No. 40 645: chassis consisting of 4 swivel castors � 125 mounted
in diamond arrangement.
Order No. Int. dimensions Ext. dimensions Contents Weight Load Adjustment(L × W× H, approx. mm) (L × W× H, approx. mm) (approx. l) (approx. kg) (kg)
40 644 1000 × 650 × 500 1060 × 710 × 820 325 24,5 90.0
40 645 1010 × 420 × 430 1060 × 470 × 800 170 21,0 30.0
40 646 1010 × 600 × 430 1060 × 650 × 800 250 25,0 45.0
40 647 1410 × 700 × 430 1460 × 750 × 800 420 29,0 60.0
40 756 1400 × 700 × 600 1460 × 760 × 920 590 31,5 150.0
ZARGESW125 Trolley
w Anodised.w Watertight.w Smooth internal surfaces.w Drain tap in floor of trolley.w Chassis: 2 swivel action and 2 fixed castors, corner-
mounted, 125 mm �, 40 mm wide, smooth running,
rubber tyres, "non-marking", with roller bearings,
thread guards.
ZARGESW128 Trolley
w Anodised.w Watertight.w Strong extruded rim.w Push-Pull handles to either end.w Inclined floor and 5/4̋ drain tap for problem-free fluid
run-off from base.w All above trolley sections protected by means of
peripheral guard with abrasion-proof plastic padding
resistant to disinfectants and temperature-resistant
up to 95°C.w Chassis: 2 fixed and 2 swivel action castors, 160 mm �,
40 mm wide, smooth running, rubber tyres,
“non-marking”, with roller bearings, thread guards.w Swivel action castors with brakes.
Special Accessoriesw Pivot pin for lift / tilt facility to DIN 30 70.w Special chassis for container washing unitsw Coupling/drawbar for in-train travel.
Order No. Description of Additional Fittings
40 888 Light alloy side flap for container aperture
40 889 Hinged lid with two snaplocks
and peripheral seal
3062 Central braking facility for 160 mm � swivel castors
Order No. Int. dimensions Ext. dimensions Contents Weight(L × W × H, approx. mm) (L × W × H, approx. mm) (approx. l) (approx. kg)
40 887 1185 × 620 × 850 1300 × 730 × 1100 620 38.0
Order No. Int. dimensions Ext. dimensions Contents Weight(L × W × H, approx. mm) (L × W × H, approx. mm) (approx. l) (approx. kg)
40 623 1000 × 700 × 400 1040 × 740 × 765 280 21.0
36
Open Trolleys
Shelf Trolley
w Anodised.w With two push-pull handles and integrated reinforced rim.w Plastic guards.w Chassis: 4 swivel action castors cornermounted, 125 mm �,
40 mm wide, smooth running, rubber tyres, “non-marking”,
with roller bearings, thread guards.w Inter-shelf clearances:
For 40 726: 488 mm, for 40 727: 230 mm.w Additional equipment: wheel brakes for 125 mm � swivel-
action castors.
ZARGESOpen Trolleys
Whether you are dealing with items that are verticallyor horizontally stacked. Luggage, boxes or bags,trays, dishes, cans or laundry ZARGES open trolleyswill accommodate everything and transport it easily and safely to its destination.
1 2
3 4System variations:
Order No. No. Platform dimensions Ext. dimensions Belastung* WeightPlatforms (L × W × H, approx. mm) (L × W × H, approx. mm) (approx. kg) (approx. kg)
40 726 2 800 × 520 925 × 640 × 870 40,0 12.0
40 727 3 800 × 520 925 × 640 × 870 40,0 16.0
* Per platform
Variomobil (Trolley Kit System)
w Open trolley on modular design basis (retrofitting possible
at any time).w Robust, smooth-finish platform.w Chassis: 2 swivel action and 2 fixed castors, corner-mounted,
160 mm �, 40 mm wide, smooth running, thread guards.w Smooth-finish demountable side and end panels (acces-
sories).
Order No. Int. dimensions Ext. dimensions Castor-� Loading Weight(L × W × H, approx. mm) (L × W × H, approx. mm) (approx. mm) (kg) (approx. kg)
40 785 1000 × 655 × 620 1200 × 750 × 1050 160 300 13.2
Order No. Description of Additional Parts for Basic Model 40 785
40 787 Push-Pull handle anodized with front end panel
40 788 Single-section side panel
37
Cupboard Trolleys
ZARGESCupboard Trolleys
The imaginative multi-functional system that ensures protection,security and hygiene in relation to storage applications as well asan efficient means of transporting tools, materials, laundry, foodand many other items.
With its robust carcass in anodised aluminium, solid profile periph-eral framework, ergonomic push-pull handles, wide-openingdoors with integrated seals and central locking, smooth-runningchassis featuring castors with rubber tyres in asymmetric arrange-ment, numerous options in relation to equipment and functionalaccessories, the ZARGES cupboard trolley is the preferred solutionto internal and external transportation and storage problems. Inindustry, service companies, government departments, hospitals,laundries etc.
w Anodised surfaces.w Two doors which can be folded back parallel to ends.w Open doors held in position magnetically.w Central locking facility, locks door panels in extruded
framework.w Two push-pull handles.w All the above trolley components protected by peripheral
guards with abrasion-proof plastic padding resistant to
disinfectants and temperature resistant up to 95°C.w Distortion-free trolley substructure (torsion tube).w Chassis: 2 swivel action and 2 fixed castors, corner-
mounted, 200 mm �, 50 mm wide, smooth-running, rubber
tyres, “non-marking”, with roller bearings, thread guards.w For accessories and special equipment please see Page 40.
ZARGESW105 Cupboard Trolleys (Without internal fittings)
Order No. Int. dimensions Ext. dimensions Contents Weight(L × W× H, ca. mm) (L × W× H, ca. mm) (approx. l) (approx. kg)
40 667 1135 × 550 × 1390 1255 × 630 × 1725 870 62.0
Other sizes on request.
Compartments Fixtures for shelves Shelf inserts
Order No. 40 785
Order No. 40 785 and 40 787
Order No. 40 785 and 2 × 40 787
Order No. 40 785 and 2 × 40 787
and 1 × 40 788
4
3
2
1
38
Cupboard Trolleys
w Layout as for order no. 40 677, but with the addition
of 2 fitted shelves and 2 wheel brakes.w Special size W105 (e.g. for sterile containers):
Layout as for order no. 40 667 but with 620 mm (internal)
trolley depth and 2 fitted shelves.w Swivel castors with central stop brakes for Order No. 40 673
(can be operated centrally via connecting rod/foot pedal)
(not illustrated)
ZARGESW105 Cupboard Trolley with 2 fitted shelves
w Layout as for order no. 40 667, but with the addition of
one fitted shelf.
ZARGESW105 cupboard trolley with one fitted shelf
W 105 Cupboard Trolley with 2 fitted shelvesOrder No. Int. dimensions Ext. dimensions Contents Weight
(L × W× H, approx. mm) (L × W× H, approx. mm) (approx. l) (approx. kg)
40 673 1135 × 550 × 1390 1255 × 630 × 1725 870 66.0
Special sizes on request.
W 105 Cupboard Trolley with 2 fitted shelves (e.g. for sterile containers)Order No. Int. dimensions Ext. dimensions Contents Weight
(L × W× H, approx. mm) (L × W× H, approx. mm) (approx. l) (approx. kg)
40 666 1250 × 620 × 1390 1370 × 700 × 1725 1080 73.0
w Note:This trolley provides space for: Sterile containers, 600 × 300 × 150 (300) mm,
Mesh container, 600 × 300 × 130 (150) mm plus other container sizes.
Special sizes on request.
W 105 Cupboard Trolley with 1 fitted shelfOrder No. Int. dimensions Ext. dimensions Contents Weight
(L × W× H, approx. mm) (L × W× H, approx. mm) (approx. l) (approx. kg)
40 669 1135 × 550 × 1030 1255 × 630 × 1365 640 59.0
Special sizes on request.
39
Cupboard Trolleys/Cage Trolleys
w Special size W105 for sterile fresh laundry, for soiled laun-
dry and many other applications.w Layout as for order no. 40 667 but with additional features
as follows:
• Plastic padded guard to top.
• Two collapsible fitted shelves with burr-free perforations.
• Black plate for labels and label holder to DIN A4.
• Arranged to accommodate a weight of 53 kg +/– 0,2 kg.
• Chassis: 2 swivel action and 2 fixed castors, corner-
mounted, 125 mm � × 40 mm wide, smooth running,
rubber tyres, “non-marking”, with roller bearings.
ZARGESW105 OP Cupboard trolley
w Steel, galvanised, yellow-chromed.w Superimposed tubular framework chassis.w Side panels, rear panel and shelves formed from robust
mesh.w Top shelf can be folded down against rear panel and centre
shelf can be folded down to front.w Front section with low wall and horizontal tie-bars.w Label plate 100 × 130 mm.w Clothes rail, 3 straps, foot plates.w Chassis: 2 swivel action and 2 fixed castors, corner mounted,
125 mm �, 40 mm wide, smooth-running, rubber tyres,
“non-marking”, with roller bearings Thread guards.w Additional equipment available at extra charge:
Extra straps, guard, wheel brakes for swivel action castors,
coupling and drawbar for in-train operation, cover, castors
160 or 200 mm �.
ZARGESGW1700 Cage trolley
Order No. Int. dimensions Ext. dimensions Contents Weight(L × W× H, approx. mm) (L × W× H, approx. mm) (approx. l) (approx. kg)
40 890 835 × 470 × 1430 965 × 545 × 1700 560 53.0
Order No. Int. dimensions Ext. dimensions Compartment height Weight(L × W× H, approx. mm) (L × W× H, approx. mm) (approx. mm) (approx. kg)
Lower, 650
43 910 740 × 540 × 1530 800 × 600 × 1730 Middle, 560 37.0
Top, 320
Supplied flat-packed for on-site assembly.
NEW!
40
Cupboard Trolley Accessories and Special Equipment
ZARGESCupboard Trolley Accessories and Special Equipment
ZARGES cupboard trolleys can be supplied without fitted shelves,with one or two fitted shelves and with special fittings for a range ofapplications. Depending on the design, cupboard trolleys may beused for a very wide variety of applications, for example, for storageand retrieval exercises, in the catering service, for transporting foodwithin the context of the restaurant trade, in hospitals and nursinghomes, as a spares store for electronic components etc. Fitted with a drawbar or tie-bar, cupboard trolleys lend themselves to in-trainuse. Washing in container washing units is also possible. In fact, theapplication possibilities are infinite.
Accessories and Special Equipment, W 105 Cupboard TrolleyOrder No. Description
3001 Fitted Shelf
3002 Clothes rail
3004 Drawbar can be folded against body section (fixed attachment towbar)
3005 Tiebar with towing bracket (demountable towing device)
3006 Lockable trolley doors, cylinder lock with keys to fit all trolleys or with separate keys
3007 for each trolley, 2 keys supplied for each lock
3060 Braked swivel castors 200 mm �3061 Central braking for swivel castors 200 mm �
w Note:Special fittings are sometimes only available subject to minimum order.
Please enquire.
Label Holder
w 74 × 50 mm,
DIN A 7/DIN A 8
150 × 50 mm, DIN A 6
212 × 50 mm, DIN A 5
210 × 148 mm, DIN A 5
296 × 210 mm, DIN A 4
with transparent window.
Embossing
w 20 mm DIN font,
capital letters.
Chassis/Castors
w � 100 mm, 35 mm wide
� 125 mm, 40 mm wide
� 160 mm, 40 mm wide
� 200 mm, 50 mm wide
Also available on request
for container washing units
etc.
Security Locks
w including master key
version.
Trailer Coupling
w for all trolley models.
Towbar
w for all trolley models.
Self-adhesive labels
w in different sizes/colours/fonts, also available in
peel-resistant version if required.
41
Recyclables Collection Systems
w Waste disposal cabinet for 1–3 waste receptacles
(PP or steel, 60 l capacity).w Powder-coated grey (similar to RAL 7040).w Easy to operate receptacle, can be securely locked
in position, easy change-over.w Open front section with full-width flap for labelling.w 4 swivel-action castors, wheel � 50 mm.w Designed for use under table or worksurface.w Note: Available if required in light alloy instead of
steel (min. order quantity 30-off).
ZARGES – Waste Disposal Cabinet, steel,1, 2 and 3 compartments
ZARGESDual Compartment, Triple Compartment
w Weatherproof carcass in steel plate, powder-coated
grey (similar to RAL 7040).w 2 lockable doors.w 3 apertures with movable flaps.w Recessed vents and inclined metal cover sheet
give protection from the rain.w Guide rail and suspension framework for waste
collection sacks inside.w Suitable for 60 l containers and standard commercial
waste sacks.
ZARGESTriple Waste Collection Station, Steel
Order No. Construction Shelf heights Weight(approx. mm) (approx. kg)
43 941 Single compartment 400 × 585 × 785 14.0
43 942 Double compartment 700 × 585 × 785 21.0
43 943 Triple compartment 1000 × 585 × 785 27.0
Order No. Construction Shelf heights Weight(approx. mm) (approx. kg)
43 921 2fach 700 × 610 × 950 13.5
43 922 3fach 1000 × 610 × 950 18.0
Order No. Ext. dimensionse Weight(L × W× H, approx. mm) (approx. kg)
43 937 980 × 590 × 1000 48.0
w Light alloy trolley with shelves.w 3-tier shelving.w Load capacity /compartment approx. 25 kgw Chassis: 4 swivel-action castors, 100 mm �,
35 mm wide, smoothrunning, rubber tyres,
“non-marking”, roller bearings, thread guards.w Suspension frame for bags: Order no. 43 931
ZARGESGlass Recyclables Collection Unit
Order No. Ext. dimensionse Shelf heights Weight(L × W× H, ca. mm) (approx. mm) (approx. kg)
43 924 720 × 520 × 1155 160 / 590 / 1035 13.5
w Light alloy framework construction, sheet metal
cladding to three sides for a range of waste collection
media (paper/plastic sacks, nets etc.).w With covers and retaining rings.w Chassis: 4 swivel-action castors, 100 mm �,
35 mm wide, smooth-running, “non-marking”,
with roller bearings, thread guards.w Additional equipment: Doors for 2-compartment
waste collecting station Order no. 43 928.w Doors for triple compartment waste collecting station
Order no. 43 927.w Note: Item not held in stock. Minimum order quantity
20-off. Please enquire.w Suspension frame for bags: Order no. 43 931
42
Recyclables Collection Systems
w Anodised.w Robust and fireproof.w Stackable.w Accessories: separate anodised light alloy lid.
ZARGESLight Alloy Waste Collection Unit
ZARGESOther Accessories
Order No. Int. dimensions Contents Weight(L × W× H, approx. mm) (approx. l) (approx. kg)
40 747 300 × 300 × 500 45 3.0
40 757 Light alloy lid (to fit 40 747 only)
46 084 300 × 264 × 493 39 2.6
w Reinforced with peripheral beading/ corner beading.w Push-Pull handle.w Hinged lid with reinforced extruded rim, complete with
approx. 420 × 24 mm aperture and security plate.w Stirrup hinge.w Chassis: Axle tube with 2 castors, � 200 mm.
ZARGESTransport Container, mobile
Order No. Int. dimensions Overall width Contents Weight(L × W× H, approx. mm) (approx. mm) (approx. l) (approx. kg)
40 896 450 × 550 × 980 580 240 15.0
Low density polyethylene bags, blue (not illustrated)Order No. Suitable for 43 923 and 43 940
43 830 1 box of 10 rolls of 25 each, density 45 �,
volume approx.60 l
Polyethylene Collection Unit Type A / BOrder No. Type Ext. dimensions Weight
(L × W× H, approx. mm) (approx. kg)
43 925 A 600 × 400 × 280 2.5
43 926 B 400 × 300 × 270 1.3
PP Recyclables Container with LidOrder No. Suitable for Ext. dimensions Weight
(L × W× H, approx. mm) (approx. kg)
43 923 43 941 –43 943, 43 921, 550 × 280 × 580 3.0
43 922, 43 937
43 933 Lid for polypropylene bin
Steel Recyclables Container (not illustrated)Order No. Suitable for Ext. dimensions Weight
(L × W× H, approx. mm) (approx. kg)
43 940 43 941, 43 942, 43 943 540 × 280 × 590 8.0
Identification LabelsOrder No. 1 set labels Consisting of 1 each:
43 944 labelled Paper, residual waste, bio-waste,
foil, metal, glass, paperboard,
plastic/synthetics
43 945 Pictograms Residual waste, paper / paperboard,
glass, tinplate, foil/synthetics
Images from left to right:
w PE Collector Box
w PE Recyclables
w Container Identification Labels
43
ZARGES Individual SolutionsLogistics Innovations for each and every sector.
ZARGESIndividual Solutions
ZARGES – Number 1 when it comes to Individual Solutions
We are fully aware that even the most comprehensiveproduct concept cannot be expected to cope with eachand every requirement. When it comes to complex indi-vidual customer- and application-related solutions, our design and development division is at your service.With our broad experience of aluminium processing, thetechnological know-how you expect from the marketleader and the creativity of a supplier who is at homewith practically any application, from the chemical andelectronics sectors right through to the automotiveindustry, we develop, fabricate and put together logis-tics solutions which have been devised down to the lastdetail to correspond with the most modern state oftechnology. Make your Just-in-Time/KANBAN solutionsa reality with ZARGES components.
A
B
w
Making Direct Contact with ZARGES
ZARGES GmbH Postfach 1630D-82360 Weilheim
Tel.: + 49-(0) 881-687-130Fax: + 49-(0) 881-687-440
u
Ide
nt.
-Nr.
16
9E
.1.0
2.0
8, e
e-Z
AR
08
20
9W
e r
ese
rve
th
e r
igh
t to
imp
lem
en
t te
chn
ica
l ch
an
ge
s. A
ll d
ime
nsi
on
s a
nd
we
igh
ts s
tate
d a
re a
pp
roxi
ma
te. C
urr
en
ta
s a
t th
e d
ate
of
go
ing
to
pre
ss. R
ep
rod
uct
ion
, in
clu
din
g t
he
re
pro
du
ctio
n o
f e
xtra
cts,
is p
erm
itte
d o
nly
wit
h t
he
ap
pro
val
of
ZA
RG
ES
Gm
bH
.
w Special SystemsTransportation and packaging
systems for applications under
special conditions in the military
sector as well as in electronics
and for hazardous goods.
[email protected].: +49-(0)881-687-131Fax: +49-(0)881-687-484
w Special SystemsUN-approved special transport
and packaging solutions for the
safe and reliable transportation
of hazardous goods.
[email protected].: +49-(0)881-687-131Fax: +49-(0)881-687-484
w Medical SystemsPlanning, fabrication and
installation of concepts and
products, tailored to the special
features of hospital logistics.
A reliable, streamlined supply of
medical products, medications,
laundry and meals to wards
and patients with the focus on
reliability in the provision of
goods and a high degree of e
conomic viability as far as the
process is concerned.
[email protected].: +49-(0)881-687-132Fax: +49-(0)881-687-525
w Access SystemsLadders, scaffolding, platforms,
assembly lifts and other access
equipment for the industrial and
service sectors, for DIY, trade
applications and the private
sector.
[email protected].: +49-(0)881-687-100Fax: +49-(0)881-687-500
Top Related