1
Assembly instructions osAKA
029220|14 COMFORTLINE
Assembly instructionsTop quality from Japan Metal shed OsakaThe assembly video can be found on: www.finnhaus.de
2
Assembly instructions osAKA
A
A
B
C
A
A
B
C
A B CA B CA B C
The basement and the cross-beam must be layed together as in the plan.
Assembly oF tHe bAsement AnD cross-beAm
required accessories
Pce no. Article Qty
Base frame, in front 1
Base frame, left 1
Base frame, right 1
Base frame, rear 1
Cross-beam 2
-Metal fitting for corner basement, front left
1
-Metal fitting for corner basement, front right
1
-Metal fitting forcorner basement, rear
2
01
02
03
04
05
Metal fitting rear corner. Metal fitting front right. Metal fitting front left.
Drive the metal fittings on the frame, so that the holes conform.
Front view with bricks used as foundation.
Front view with plastic plates used as foundation.Supplied with house.
01
0102
02
03
03
04
0405
05
05
05
To guarantee the shed stands correctly it requires a good found-ation. (More information can be found in our leaflet).
The shed must be built raised from the ground to insure that the rain water can run underneath.
3
Assembly instructions osAKA
A
A
B
C
Front view
Spirit level
Short screws
Short screws
Short screwsShort screws
※
※
Attention: Please insure that all the base frame parts are level, so that after completion the door opens and closes easily.
FittinG oF tHe bAse FrAme AnD tHe cross-beAm
01
02
03
04
05
required accessories
Pce no. Article Qty
- Short screws 14
- Spirit level 1
After the frame has been checked that it is level the two screws marked can then be secured, checking that there are no gaps in between the frame parts.
※
b + cMetall fittingfor the front
※
Short screwsAMetall fittingfor the rear corner
Short screws
05
4
Assembly instructions osAKA
Assembly oF tHe corner post
required accessories
Pce no. Article Qty
Corner post, front left 1
Corner post, front right 1
Corner post, rear left 1
Corner post, rear right 1
- Short screws 14
06
07
08
09
Slot
Hook
Put the hook in the slot.
Short screws
Tighten all the screws.
07
02 03
04
01
09
08
06
Front view
Attention:To maintain that everything is at a right angle check the length of diagonals are exactly the same.
Please check that all the edges of the frames are together. Otherwise the ground panels may not fit.
5
Assembly instructions osAKA
Assembly oF tHe reAr AnD Front rooF FrAme
required accessories
Pce no. Article Qty
Roof frame, rear 1
Roof frame, front 1
- Rubber plug, small 2
- Short screws 6
15
19
Shortscrews
Shortscrews
Rubber plug,small
Slot
Hook
Hook
Rubber plug,small
Short screws
Hook the top rear frame in both corner post slots and screw tightly.
Hook the top over the front corner post lip. Fit bottom hook in slot and secure with two short screws.
After fitting the rear top framework please fit the smaler rubber grommets (these holes are for electric cable).
A b1519
06
08
08
06
07
19
0915
Front view
6
Assembly instructions osAKA
Assembly oF tHe leFt AnD riGHt DecorAtiVe coVer
required accessories
Pce no. Article Qty
Decorative cover, left 1
Decorative cover, right 1
- Short screws 6
17
18
A
B
short screws
short screwsA
b
18
15
09
18
19
07
18
17
Front view
7
Assembly instructions osAKA
Assembly oF tHe centrAl WAll strenGtHeners For tHe leFt, riGHt AnD tHe reAr
Please fit the wall strengthener provisionaly.
Screw the metal holder for the gutter to the central post .
A b
14
Hole to the inside
Centralhole
Top, shorter
Bottom, longer
①
②
c
1111
1212
1313
Centralhole
Top side
Hole to the inside
Shortscrews
Side view
14
12
12
13
1314
14
14
15
13 12
Metal holder for gutter
Metal holder for gutter
11
14
required accessories
Pce no. Article Qty
Central wall strengthener, left, right
2/2
Central wall strengthener,rear
3
- Metal holder for gutter 1
- Short screws 15
13
12
8
Assembly instructions osAKA
Assembly oF tHe centrAl WAll strenGtHeners in Front
required accessories
Pce no. Article Qty
Central wall strengthener, front
2
- Long screws 2
- Short screws 2
- Nut 2
10
Shortscrews
Longscrews
Nut
Longscrews
Nut
NutLongscrews
Aupper Attachement
Shortscrews
blower Attachement
The base of the strengthener is pressed and secured into the third hole of the corner post.
please watch the
hook direction!
left right
Counting from corner post use third hole.
threaded hole for door panelthreaded hole for the central wall
strengthener in front
19
10
10
10
10
Attention!Don‘t forget to
secure the top of the
strengthener.
For a door opening left: The strengthener is turned over and is secured on the baseframe in the third hole from left.
01
9
Assembly instructions osAKA
required accessories
Pce no. Article Qty
Central Ground panel
2
Ground panelleft, right
2
- Special screw 16
Assembly oF tHe GrounD pAnel
29
30
The front of the ground panel (C) to be mounted over ledge of gutter.
Please use the special srews. (If the screws do not fit exactly please take a look on page 27 (3) tips for Assembling)
A
B
C
Specialscrew
30
30
29
29
A b cBasement groundpanel
Side view Front viewRear view
Basement groundpanel Basement
groundpanel
10
Assembly instructions osAKA
A bag with each roof panel contains sevensnow plugs. Remove glue covering and fitas shown.
Assembly oF tHe rooF pAnels
required accessories
Pce no. Article Qty
Roof panel, big 4
- Short screws 16
- Snow plug (4 Bags) 28
27
27
27
27
27
Fit roof starting on left side.
Slop roof down to rear so that rain can drop off there.
Rear
Strengthering
Short screws
Front Fit roof in this order.
ARear
Strengthe-ring
Shortscrews
27
27
15 19
27
27 27
2727 27 27
27 27
Attention!Before mounting the
roof fill holes with snow
plugs.
27
11
Assembly instructions osAKA
Assembly oF tHe rooF stAbiliser
required accessories
Pce no. Article Qty
Roof stabiliser 2
- Long screws and nuts each with
24
16
16
16
Lift the roof stabilisator and secure with two long screws central holes.
Strengthering of the roof panels
lower side
upperside
long screwNut
Nut
longscrew
Longscrews
Nut
longscrew
1.
Fix both ends of the stabilisator with nuts and bolts.
2.
3.NutNut Nut
longscrew
longscrewlong
screw
Please check all nuts and bolts are tight.
27
1612 13+ 12 13+
1
2
2
12
Assembly instructions osAKA
1
2
1
2
Assembly oF tHe siDe WAll pAnels
required accessories
Pce no. Article Qty
Side wall panel big 10
- Hooks out of aluminium 3
- Short screws 18
- Long screws and nuts 21
20
1. beFore AssemblinGOnly the hooks within the red markings can be moved when the shed is finished. Please decide – before the shed is build up – where the hooks should be.
Attaching the hooksThe hooks can be mounted in the holes of the large or small sides of the panels but with a max. of 2 kg per hook.
2. mount1. Place the bottom of the panels in the base frame.2. Lift top of place between posts.
While assembling the side wall panels do not let them go, before they are not provisorily bolted. They might fall down and hurt someone.
20
20
30
Upperwall strengthener
13
Assembly instructions osAKA
Assembly oF tHe siDe WAll pAnels
20
20
20
20
20
20
20
20
20
20
1. siDe WAll pAnels, reArPlease check the right angle of 90 ° between the base frame and the posts.
2. boltinGIn corner posts secure with short srews, all the strengtheners with long nuts and bolts and strengthen, then fix strengtheners.
First fix panels to corner posts provisionally and tighten all the screws.
Shortscrews
Longscrews
Nut
Side view Rear view
2020 20 20 2020 20
14
Assembly instructions osAKA
26
7
8
3
5
4
1
2 6
7
8
3
5
4
1
Please fit the screws as shown.
74 24
Assembly oF tHe Door pAnel For openinG At tHe riGHt
required accessories
Pce no. Article Qty
Side wall panel big, front right and left
1/1
- Short screws 16
24
74
90°
Shortscrews
Be shure that the doors are right angles.
24
74
10
10
15
Assembly instructions osAKA
Assembly oF tHe Front DecorAtiVe coVer AnD tHe HeiGHt compensAtion coVer bAr
required accessories
Pce no. Article Qty
Decorative cover, front 1
Height compensation cover bar
1
- Screw head caps 3
- Short screws 7
25
51
Shortscrews
Hole cover
Roof panel
25
51
25
2519
1
2
Hook the trim panel in the front roof frame.
Rotate the trim panel as shown up over the roof and secure it with short screws.
Secure the adjustment ledge with three short screws and hole caps.
1
2
3
16
Assembly instructions osAKA
Assembly oF tHe Gutter
required accessories
Pce no. Article Qty
Gutter 1
- Short screws 5
26
26
Hook both ends of the gutter on the trim panels.
Rotate over the roof and secure it with short screws.
Shortscrews
1
2
26
15
metal holderfor the gutter
17
Assembly instructions osAKA
Put both bends with connecting piece together
Fit clamps over down pipe and attache both bends with connection piece to gutter.
ATTENTION:Please cut the rainwater pipe to the correct length BEFORE assembling it. The metal clamps have to be slid onto the rainwater pipe before mounting.
Secure the down pipe to the angle joint star-ting from the top, then centre and last at the bottom.
Secure with the same screw as corner post.
Bend
Drain hole
Angle joint
Screw the three angle joints with short screws.
Gutter
Hole for rainwaterr
Angle joint
Angle joint
Metal clamp forrainwater pipe
Shortscrews
Shortscrews
Short screws
Angle joint
Bend
Rainwater pipe
Connectionpiece
Shortscrews
siDe VieW
1
3
2
Assembly oF tHe rAinWAter pipe
Fit both down pipes left and right. required accessories
Pce no.
Article Qty
-
Rainwater pipe and connec-tion piece
2/2
-
Metal clampand angle joint
6/6
- Bend 4
-Short screws
10
18
Assembly instructions osAKA
Assembly For riGHt HAnD Doors
required accessories
Pce no. Article Qty
Door, front right 1
Door, front left 1
- Metal stopper 4
- Short screws 4
- Door stop cover 2
32
31
32
31
Before mounting door please fit both metal stoppers top and bottomas shown.
Take precaution that the cylinder lock isn‘t scratched.
Shortscrews
Metalstopper
Metalstopper
Metalstopper
First fit both hooks of the metal stoppers in the slots as shown.
Door stop cover
Runner wheel unit
Fit door stop cover on left door on left side. For a right hand door, fit door stop cover on the right.
Door stop cover
Runner wheel unit at the door
Likewise on left for right door.
Attention! To build the left hand
door, go to page 19 in
this assembly instruction.
19
Assembly instructions osAKA
32
3183
33
Assembly For leFt HAnD Doors
3183
32
33
24
74
10
10
Drip ledge
Place rear movable door in lower rear sill and hook on the runner wheels, so that there is a wheel either side of the fixed door strengthener.
Afterwards place front door in front sill and hook on runner wheels on either side of drip ledge.
required accessories
Pce no. Article Qty
Door, front left 1
Door, front right 1
Door paneel, rear right 1
Door paneel, front left 1
31
32
33
833233
Hook bottom of door in rear sill.
Hook bottom of door in front sill and fit top in upper door sill.
Fit top in upper door sill.1 2
1 1
2 2
ADJustinG tHe Door
check the following points:
1. Before fitting the front decoration cover, check that both doors completly open and shut.
2. Check the doors are square.3. The door lock must work perfectly.
problems with the lock?See „Tips for assembling“ on page 26 (7).
Lock Unlock
20
Assembly instructions osAKA
AssemblinG tHe Front DecorAtion coVer
required accessories
Pce no. Article Qty
Front decoration cover 1
- Metal holder for the upper front decoration cover
2
- Door holder 1
- Short screws 6
34
Shortscrews
Door holder
Stick the top of the door holder in the slot in the front decoration cover.
Stick the other end of the door holder in the slot in the frame.
Fix the door holder with a short screw.
Metal holder for the upper front decoration cover
Front decorationcover
34
Metal holder forthe upper frontdecoration cover
1. Fit the front decoration cover between the corner posts and provisionaly srew on.
2. Then fit both metal holder in the slots.
3. The front decoration cover will lock in exactly. When complete tighten screws.
34
34
A
b
1
1
3
2
3
2
Door holder
21
Assembly instructions osAKA
Mount with long screws and nuts.Fix Pce no. with
B
B
AssemblinG tHe rAcKs
Short screws
required accessories
Pce no. Article Qty
Rack frame for side panels 4
Rack frame for rear wall1
Cross rear strengthener 2
Front cross strengthener1
- Short screws 2
87
88
39
87
87
39
90
87
88
88
20
20
20
Bottom of rack frame fits in gap between ground and wall panels.
39
90
building the racks
Hook the rear rack frame in the last gap on wall panels. Then add the front rack frame to fit shelves.
For large wall panelsUse the first gap in the central panel,for front rack frame.
Gap
87
A
cross strengthening
Fix the rear central rack frame and hook the top and bottom strengthener in and secure the front frame.
b88
39
22
Assembly instructions osAKA
FittinG tHe sHelVes
required accessories
Pce no. Article Qty
-Metal shelves supports
16
Big shelf 4
You need four metal shelves supports for one shelf. (Two on each side)
For example: With a gap of 5 cm you can create 21 ranks.
Lay the shelves on top of the metal shelves supports.
TY33
336100402
You can find the sticker with the piece number under the shelf.
Possible arrangement from the top.The big and small shelves can be adjusted as wished.
335
23
Assembly instructions osAKA
AncHorinG tHe builDinG
required accessories
Pce no. Article Qty
- Anchor, big 4
- Anchor, small 4
- Short screws 8
2. Your chosen basement.
3. Pour cement.
1. The fitting dowels and screws are not included.
※※
Fix two ankers at each side of the corner post using short screws.
Anchor,small
Anchor,big
Shortscrews
The shed must be ankered to protect against falling over.
The accessoires marked „ “ may be used when the shed is more than 120 mm above ground. In this case the large anchors can be lengthened with the short anchors and short screws.
※
24
Assembly instructions osAKA
FittinG tHe screW cAps AnD coVer
required accessories
Pce no. Article Qty
- Screw head cover 50
-Cover forrightangled holes
2
Check that all screws are tight before you fit all 50 screw head covers and the door slot covers on.
In cold weather the plastic cover can become hard. In this case warm up for example in your trouser pocket to soften.
Screw head cover
Cover for rightangled holes
Fit the top end first with double notch and press cover all in post, finally slide down.
Cover with arrow must be fitted pointing down.
Rightangled hole in corner post.
Mount the rubber plug on thefront, right and left corner post.
Press the rubber plug together to fit easily into the corner post.
Hole forrubber plug
25
Assembly instructions osAKA
GENERAL ADVISE
1. Ensure the ground is flat and firm where you want to build uo your metal shed. (For example a concrete foundation or a concrete pier foundation, where the shed is to be built)
2. Ensure that no excessive rain or snow could damage the shed. For example from a house roof.
3. Do not carry the heavy parcels alone so that the material does not get damaged. Please wear gloves and a longarmed shirt while building the metal shed to protect your hands and arms from insury.
mountinG ADVise For tHe substructure / Floor pAneles1. Ensure youself that the base frame is level
and square (for example on a cemented underground) before you start mounting the floor panels.
2. Measure the diagonals with a tape measure.
�The�diagonals�A�and�B�have�to�be�same�length,�they�have�to�build�a�uniform�rectangle.
3. The holes in the panels and the base frame must lie over each other. Check with the Philips screw driver.
TIPS FOR ASSEMBLING
26
Assembly instructions osAKATIPS FOR ASSEMBLING
Screwing: Firstly screw the four corner posts with panels provionally and check that none are cross threaded. Then tighten.
Please screw CAREFULLY to protect the screws threads from damage.
4. Please anker the shed to the ground with supplied accessoires. Control that all is correctly screwed.
5. For electric wiring call in an electrician.
6. If a door sticks adjust runner wheels to run free.
7. Lock problems? Spray a small amount of oil in the locked door as shown.
Top Related