SWG Conversion Sheet
Page 1
Diameter Aspect Ratio
(AWG) (inches) (mm) (inches) (mm) (inches) (mm) (inches) (mm)
4 0.2320 5.8930 0 0.0000 0 0.0000 0.00 0.00
5 0.2120 5.3850 0 0.0000 0 0.0000 0.00 0.00
6 0.1920 4.8770 0 0.0000 0 0.0000 0.00 0.00
7 0.1760 4.4700 0 0.0000 0 0.0000 0.00 0.00
8 0.1600 4.0640 0 0.0000 0 0.0000 0.00 0.00
9 0.1440 3.6580 0 0.0000 0 0.0000 0.00 0.00
10 0.1280 3.2510 0 0.0000 0 0.0000 0.00 0.00
11 0.1160 2.9460 0 0.0000 0 0.0000 0.00 0.00
12 0.1040 2.6420 0 0.0000 0 0.0000 0.00 0.00
13 0.0920 2.3370 0 0.0000 0 0.0000 0.00 0.00
14 0.0800 2.0320 0 0.0000 0 0.0000 0.00 0.00
15 0.0720 1.8290 0 0.0000 0 0.0000 0.00 0.00
16 0.0640 1.6260 0 0.0000 0 0.0000 0.00 0.00
17 0.0560 1.4220 0 0.0000 0 0.0000 0.00 0.00
18 0.0480 1.2190 0 0.0000 0 0.0000 0.00 0.00
19 0.0400 1.0160 0 0.0000 0 0.0000 0.00 0.00
20 0.0360 0.9140 0 0.0000 0 0.0000 0.00 0.00
21 0.0320 0.8130 0 0.0000 0 0.0000 0.00 0.00
22 0.0280 0.7110 0 0.0000 0 0.0000 0.00 0.00
23 0.0240 0.6100 0 0.0000 0 0.0000 0.00 0.00
24 0.0220 0.5590 0 0.0000 0 0.0000 0.00 0.00
25 0.0200 0.5080 0 0.0000 0 0.0000 0.00 0.00
AWG Conversion Data Source: SWG Conversion Data Source:
(Imperial) Standard Wire Gauge (SWG)Standard Wire
GaugeRing Inner Diameter
Ring Outer Diameter
To calculate Aspect Ratios, enter the Ring Inner Diameters as either fractions (1/4) or decimals (.25). The only cell on the Aspect Ratio Calculator that you can click on are the cells inside the Red Boxes. Everything else is calculated formulaically.
http://www.engineeringtoolbox.com/awg-wire-gauge-d_731.htmlhttp://home.kooee.com.au/pel/Articles/SWG_conv.pdf
SWG Conversion Sheet
Page 2
American Wire Gauge (AWG)
Diameter Aspect Ratio
(AWG) (inches) (mm) (inches) (mm) (inches) (mm) (inches) (mm)
4 0.2043 5.1892 0 0.0000 0 0.0000 0.00 0.00
5 0.1819 4.6203 0 0.0000 0 0.0000 0.00 0.00
6 0.1620 4.1148 0 0.0000 0 0.0000 0.00 0.00
7 0.1443 3.6652 0 0.0000 0 0.0000 0.00 0.00
8 0.1285 3.2639 0 0.0000 0 0.0000 0.00 0.00
9 0.1144 2.9058 0 0.0000 0 0.0000 0.00 0.00
10 0.1019 2.5883 0 0.0000 0 0.0000 0.00 0.00
11 0.0907 2.3038 0 0.0000 0 0.0000 0.00 0.00
12 0.0808 2.0523 0 0.0000 0 0.0000 0.00 0.00
13 0.0720 1.8288 0 0.0000 0 0.0000 0.00 0.00
14 0.0641 1.6281 0 0.0000 0 0.0000 0.00 0.00
15 0.0571 1.4503 0 0.0000 0 0.0000 0.00 0.00
16 0.0508 1.2903 0 0.0000 0 0.0000 0.00 0.00
17 0.0453 1.1506 0 0.0000 0 0.0000 0.00 0.00
18 0.0403 1.0236 0 0.0000 0 0.0000 0.00 0.00
19 0.0359 0.9119 0 0.0000 0 0.0000 0.00 0.00
20 0.0320 0.8128 0 0.0000 0 0.0000 0.00 0.00
21 0.0285 0.7239 0 0.0000 0 0.0000 0.00 0.00
22 0.0254 0.6452 0 0.0000 0 0.0000 0.00 0.00
23 0.0226 0.5740 0 0.0000 0 0.0000 0.00 0.00
24 0.0201 0.5105 0 0.0000 0 0.0000 0.00 0.00
25 0.0179 0.4547 0 0.0000 0 0.0000 0.00 0.00
Inches to mm Converter
Conv. inch to mm Conv. mm to inch
(inches) (mm) (mm)(inches)
Dec Frac
0 0.0000 0.0000 0.00 0
American Wire Gauge
Ring Inner Diameter
Ring Outer Diameter
To calculate Aspect Ratios, enter the Ring Inner Diameters as either fractions (1/4) or decimals (.25). The only cell on the Aspect Ratio Calculator that you can click on are the cells inside the Red Boxes. Everything else is calculated formulaically.
http://www.engineeringtoolbox.com/awg-wire-gauge-d_731.htmlhttp://home.kooee.com.au/pel/Articles/SWG_conv.pdf
Top Related