Wireless Advanced Installation Guide - W. W. Grainger · 2015-03-18 · PJ2-WALL - If one switch...

Wireless

1

0301710a 04/2014

Advanced Installation Guide

Two Switch Locations for Controlling Lights - 3-Way Installation: If you have two switches controlling your lights, follow this procedure to install your in-wall dimmer. .............................................................................................Page 2 - 5

Three or More Switch Locations for Controlling Lights - Multi-Location Installation: If you have three or more switches controlling your lights, follow this procedure to install your in-wall dimmer ...........................................Page 6 - 10

Adjusting Low-End Trim on the CasétaT In-Wall Dimmer: Follow this procedure if you experience performance issues such as flickering, flashing or other abnormal light behavior when your in-wall dimmer is at a low light level ...1

Adjusting High-End Trim on the CasétaT In-Wall Dimmer: Follow this procedure to adjust the maximum light output allowed by your in-wall dimmer ............................................................................................................................Page 12

Adjusting Low-End Trim on the CasétaT Plug-In Lamp Dimmer: Follow this procedure if you experience performance issues such as flickering, flashing or other abnormal light behavior when your plug-in lamp dimmer is at a low light level .........................................................................................................................................................Page 13

Adjusting High-End Trim on the CasétaT Plug-In Lamp Dimmer: Follow this procedure to adjust the maximum light output allowed by your plug-in lamp dimmer ...........................................................................................................Page 14

Converting a CasétaT Plug-In Lamp Dimmer to a Switch to Control Non-Dim Loads (Lights Only): Follow this procedure if you would like your plug-in lamp dimmer to act as a switch for non-dimmable lighting loads ..................Page 15

Removing Paired Devices from a CasétaT Wireless Dimmer: Follow this procedure if you need to remove paired PicoR remote controls or reset your dimmer to its factory default settings ..........................................................Page 16

Changing the Favorite Light Level on the Pico® Remote Control: Follow this procedure to change the light level your dimmer recalls when you press the "Favorite" button on your PicoR remote control. ..............................................Page 17

Troubleshooting ..............................................................................................................................................................Page 18

In-wall dimmer - PD-6WCL Plug-in lamp dimmer - PD-3PCL

Thank you for purchasing CasétaT Wireless from Lutron. This document will guide you through several additional installation topics beyond those covered in the quick-start guide included with your product.

Table of Contents

Wireless

2

0301710a 04/2014

1 Identify existing wiring

Two switches control the lights (3-way installation)

2 What you need for a 3-way installation

+

WARNING! Shock Hazard. May result in serious injury or death. Turn off power at circuit breaker before installing the unit.

4 Turn power off at circuit breaker

5 Remove existing switch from wall

6 Tag and disconnect wires from the switch

Place tag - to identify wire on different color screw

Different Color Screw

Ground(Green / Bare Copper)

Two Switch Locations for Controlling Lights - 3-Way Installation

Location 1 Location 2

In-wall dimmerPD-6WCL or P-PKG1W

Pico remote control with wall-mounting kitPJ2-WALL

- If one switch controls the lights (single-pole installation) See quick-start guide that came with your dimmer

- If three or more switches control the lights (multi-location installation) See page 6 for details

Important note:

3 Choose a location for your dimmer

Choose which switch location you want the dimmer installed in. This will be Location 1.

Location 1

Location 1

Wireless

3

0301710a 04/2014

7 Remove side sections (if necessary)

Do not remove outside side sections

on dimmers at the end of gang.

Each dimmer has inside

side sections removed.

Dimmer in middle has all


CFL/LED Total Wattage Incandescent/Halogen Total Wattage

0 W + 600 W 500 W 400 W

1 W – 25 W + 500 W 400 W 300 W

26 W – 50 W + 400 W 300 W 200 W

51 W – 75 W + 300 W 200 W 100 W

76 W – 100 W + 200 W 100 W 50 W

101 W – 125 W + 100 W 50 W 0 W

126 W – 150 W + 0 W 0 W 0 W

A B C

B B B C BA

8 Connect the dimmer

Tagged Wire

Ground(Green Wire)

9 Mount the dimmer

10 Attach the wallplate

‘snap’

11 Remove existing switch from wall at Location 2



Ground (Green / Bare Copper)Different Color Screw

Important note:Removing side sections reduces the dimmer’s maximum wattage

rating. See the chart below for maximum wattage information.

When installing more than one dimmer in the same wallbox, it is necessary to remove inner side sections prior to wiring (see image below). See below for derating information.

Wallplate Adapter Wallplate

Location 1

Location 1

Location 2


Location 2

Location 1

Wireless

4

0301710a 04/2014

13 Connect the wires

Ground

14 Attach the wallplate bracket and remote control


‘snap’

16 Turn power on at circuit breaker


Pairing the dimmer and PicoR remote control

17 Press and hold "Off" button on dimmer

05

10

15

6 sec.

UntilHold

Indicator lights flash

18 Press and hold "Off" button on remote control

Lights flash three times

05

10

15

6 sec.

Until


Location 2

Tagged Wire

Location 2

Location 2

Location 2

Location 1

Repeat steps 17 and 18 to pair additional remote controls.

19 Pair additional remote controls

Hold3x

Wireless

5

0301710a 04/2014


Neutral

Pico®

Remote ControlLine / Hot

Traveller

Dimmer *

Ground

Load

Schematic Diagram

Traveller

* Dimmer may be installed in either location.

Tagged WireTagged Wire

Wireless

6

0301710a 04/2014

Three or More Switch Locations for Controlling Lights - Multi-Location Installation

1 Identify existing wiring

2 What you need for a mult-location installation

+

WARNING! Shock Hazard. May result in serious injury or death. Turn off power at circuit breaker before installing the unit.

4 Turn power off at circuit breaker


+

- If one switch controls the lights (single-pole installation) See quick-start guide that came with your dimmer

- If two switches control the lights (3-way installation) See page 2 for details

Important note:

In-wall dimmerPD-6WCL or P-PKG1W

Pico® remote control with wall-mounting kitPJ2-WALL

Pico® remote control with wall-mounting kitPJ2-WALL

3 Choose a location for your dimmer

NOTE: There will be two different types of existing switches in this

application. Locations 1 and 3 will use 3-way switches (three screws

which control the lights, plus one ground screw) and Location 2 will use

a 4-way switch (four screws which control the lights, plus one ground

screw). For easiest installation, we recommend replacing one of the 3-way

switches with your dimmer (Locations 1 or 3). In this example, we will use

Location 1.

Location 1

3-Way Switch Locations 1 and 3

4-Way Switch Location 2

Three or more switches control the lights (multi-location)

Location 1 Location 2 Location 3

Wireless

7

0301710a 04/2014


8 Connect the dimmer

9 Mount the dimmer


‘snap’



Tagged wireLocation 1

Location 1

Location 1


7 Remove side sections (if necessary)

Do not remove outside side sections

on dimmers at the end of gang.

Each dimmer has inside


Dimmer in middle has all


CFL/LED Total Wattage Incandescent/Halogen Total Wattage

0 W + 600 W 500 W 400 W

1 W – 25 W + 500 W 400 W 300 W

26 W – 50 W + 400 W 300 W 200 W

51 W – 75 W + 300 W 200 W 100 W

76 W – 100 W + 200 W 100 W 50 W

101 W – 125 W + 100 W 50 W 0 W

126 W – 150 W + 0 W 0 W 0 W

A B C

B B B C BA

When installing more than one dimmer in the same wallbox, it is necessary to remove inner side sections prior to wiring (see image below). See below for derating information.

Important note:Removing side sections reduces the dimmer’s maximum wattage

rating. See the chart below for maximum wattage information.

Different Color Screw



Location 1

Wireless

8

0301710a 04/2014



‘snap’




Location 2

Location 2



Tagged Wires

Location 2



Ground (Green / Bare Copper)

Location 2

Location 2

Place tags - to identify wires on different color screws

Different Color Screws

Location 3

Wireless

9

0301710a 04/2014


21 Turn power on at circuit breaker

Pairing the dimmer and PicoR remote control

22 Press and hold "Off" button on dimmer

05

10

15

6 sec.

UntilHold

Indicator lights flash

23 Press and hold "Off" button on remote control

05

10

15

6 sec.

Until

Location 2

Location 1

Repeat steps 22 and 23 to pair remote control at Location 3.

24 Repeat for remote control at Location 3


Different Color ScrewGround (Green / Bare Copper)



Ground (Green / Bare Copper)


Location 3

Tagged Wire

Location 3

Location 3


‘snap’


Location 3

Hold

Lights flash three times

3x

Wireless

10

0301710a 04/2014


Neutral

Pico®

Remote ControlLine / Hot

Traveller Traveller

Traveller Traveller

Dimmer *

Ground

Load

Schematic Diagram

Pico®

Remote Control

* It is recommended to install dimmer in either Location 1 or 3.

Location 1 Location 2 Location 3

Tagged Wire Tagged Wires

Wireless

11

0301710a 04/2014

Adusting Low-End Trim on the CasétaT In-Wall Dimmer - PD-6WCL

On

Off

Darker

Brighter

In-wall dimmer

Adjusting Low-End Trim -

To optimize performance of CFL / LED lamps

1 Enter

05

10

15

6 sec.

Until

2 Adjust

Hold

Hold untilHold

a.

2 Adjust (continued)

Light stops flickering

and is stable

b.

Tap until

An indicator light

starts flashing

Light stops dimming

or turns off

Hold until

Indicator light stops flashing

4 Verify

a. Tap "Off" one time. Light will turn

off.

b. Tap "Brighter" one time. Light will

turn on.

c. If light is still off or is flickering,

repeat steps 1-4.

a.

b.

b.

3 Save

Wireless

12

0301710a 04/2014

Adusting High-End Trim on the CasétaT In-Wall Dimmer - PD-6WCL

Adjusting High-End Trim -


1 Enter

05

10

15

6 sec.

Until

2 Adjust

Hold

Hold untilHold

a.


Desired light level

is achieved

b.

Tap until

An indicator light

starts flashing

Hold until

Indicator light stops flashing

3 Save

Light is at full

brightness

On

Off

Darker

Brighter

In-wall dimmer

Wireless

13

0301710a 04/2014

Plug-in lamp dimmer

Adusting Low-End Trim on the CasétaT Plug-In Lamp Dimmer - PD-3PCL

On

Off

Darker

Brighter

Adjusting Low-End Trim -


1 Enter

05

10

15

6 sec.

Until

2 Adjust

Hold

Hold until

Hold

a.


b.

Tap until

The indicator light

starts flashing

Hold until

The indicator light stops flashing

4 Verify

a.

b.

Light stops dimming

or turns off

Light stops flickering

and is stable

a. Tap "Off" one time. Light will turn

off.

b. Tap "Brighter" one time. Light will

turn on.

c. If light is still off or is flickering,

repeat steps 1-4.

3 Save

Wireless

14

0301710a 04/2014

Plug-in lamp dimmer

On

Off

Darker

Brighter

Adjusting High-End Trim -


1 Enter

05

10

15

6 sec.

Until

2 Adjust

Hold

Hold until

Hold

a.


b.

Tap until

The indicator light

starts flashing

Light is at full

brightness

Hold until

The indicator light stops flashing

Desired light level

is achieved

3 Save

Adusting High-End Trim on the CasétaT Plug-In Lamp Dimmer - PD-3PCL

Wireless

15

0301710a 04/2014

Converting a CasétaT Plug-In Lamp Dimmer to a Switch to Control Non-Dim Loads

1 Press and Hold "On" and "Off" buttons

05

10

15

6 sec.

UntilHold

The indicator light

flashes

2 Verify

a. Tap "Off" one time. Light will

turn off.

b. Tap "On" one time. Light will

turn on.

– The "Brighter" and "Darker"

buttons will be disabled and

do nothing.

Note: Only use lighting loads on

your plug-in lamp dimmer,

even when operating in switch

mode.

a.

b.

3 To change back to dimmer mode repeat step 1

Plug-in lamp dimmer

On

Off

Darker

Brighter

Wireless

16

0301710a 04/2014

Removing Paired Devices from a CasétaT Wireless Dimmer

1 Tap the "On" button quickly three times, holding on the last press

05

10

15

3 sec.

2 Continue to hold the "On" button until the light begins to flash quickly.

Tap Tap

Until

3 Release the button, then immediately tap the button three more times

Tap Tap

3x

Light will flash slowly

three times, then turn off

4 All paired remotes are removed and all settings are returned to factory default.

– After the dimmer resets, the light will turn on to the full on state.

Note: This procedure also resets the high-end and low-end trim settings.

Hold

Hold

3x

Light starts

flashing quickly

3x

Wireless

17

0301710a 04/2014

You can use the round “Favorite” button on the

PicoR remote control to recall a favorite light level.

We’ve set it to 50%, but you can change it to any

level you like.

Favorite

1 Set desired light level on dimmer that has already

been paired with a remote control

2 Save favorite light level

05

10

15

6 sec.

Until

Indicator light(s)

flash(es) two times

3 Verify

Changing the Favorite Light Level on the Pico® Remote Control

or

2x

2x

or

a. Tap "Off" button one time on

remote control. Light will turn off.

b. Tap "Favorite" button one time

on remote control. Light will turn

on to saved level.

a.

b.

Wireless

18

0301710a 04/2014

Lutron Contact Numbers

Lutron and Pico are registered trademarks and FASS and Caséta are trademarks of Lutron Electronics Co., Inc.

WORLD HEADQUARTERS USA

Lutron Electronics Co., Inc. 7200 Suter Road Coopersburg, PA 18036-1299 TEL: +1.610.282.3800 FAX: +1.610.282.1243 Toll-Free: 1.888.LUTRON1 Technical Support: 1.800.523.9466

[email protected]

Lutron Electronics Co., Inc.7200 Suter RoadCoopersburg, PA 18036-1299 U.S.A.P/N 0301710 Rev. A 04/2014

Troubleshooting

North & South America Technical Hotlines

USA, Canada, Caribbean: 1.800.523.9466 Mexico: +1.888.235.2910 Central/South America: +1.610.282.6701

Symptoms Probable cause and action

Light does not turn on or dimmer's LEDs do notlight up.

• Light bulb(s) burned out.

• Breaker is OFF or tripped.

• Light not properly installed.

• Wiring error.

In-wall dimmer only

• FASST switch on the dimmer is in the off position.

Plug-in dimmer only

• Outlet is switched off.

• Lamp is turned off.

• Lamp is not plugged in.

Light does not respond to PicoR remote control. • The dimmer failed to pair with PicoR remote control.

• The dimmer is already at the light level the PicoR remote control is sending.

• The PicoR remote control is outside the 30 ft (9 m) operating range.

• The PicoR remote control battery is low.

• The PicoR remote control battery is installed incorrectly.

• Bulbs turn off while being dimmed.

• Bulbs turn on at high light level but do not turn on at a low light level.

• Bulbs flicker or flash when dimmed to a low light level.

Verify bulbs are marked dimmable and visit www.casetawireless.com/lowend for information on adjusting the dimmer for best bulb performance.

Go to www.casetawireless.com/support for additional troubleshooting suggestions.

Wireless Advanced Installation Guide - W. W. Grainger · 2015-03-18 · PJ2-WALL - If one switch...

Documents

Transcript of Wireless Advanced Installation Guide - W. W. Grainger · 2015-03-18 · PJ2-WALL - If one switch...