Weld Prospektus 2015 02 copy - Graboplast Zrt. · mecánica o manual, con la profundidad y anchura...
Transcript of Weld Prospektus 2015 02 copy - Graboplast Zrt. · mecánica o manual, con la profundidad y anchura...
WELDGraboplastFloor Covering Manufacturers Ltd.H-9023 Győr, Fehérvári út. 16/b.Telefon: (+36) 96 506-100
www.graboplast.com
The glued floorcovering should be grooved at the joints mechanically or manually in an adequate depth and width. Any contamination should be removed. Welding should be made either by automatic or manual welding machine. The recommended temperature is 300 ºC, but in order to set the optimal temperature and speed, test welding should be made in all cases. When applying round-diameter welding rod, the surplus, after the weld seam is cooled off should be removed in 2 steps: first the cord is cut into half by the help of a trimming guide and a quarter moon knife. Then, after total cooling off, the balance is cut to flat by a quarter moon knife.
WELDING
El fresado de las juntas del pavimento se puede realizar con maquina fresadora mecánica o manual, con la profundidad y anchura adecuadas, limpiando la hendidura resultante de posibles restos. Podemos hacer la soldadura con un soldador automáti-co o manual. La temperatura del soldador debe ajustarse normalmente entre 300 centigados, pero para establecer la temperatura y velocidad óptimas, es necesario realizar previamente unde prueba. En caso del soldar con cordon graboWeld de sec-cion circular, debe eliminarse el cordon sobrante cortando a ras de pavimento con una cuchilla tipo “cuarto de luna” una vezque el cordon se haya enfriando totalmente.
SOLDADURA
A leragasztott padlóburkolót az illesztéseknél gépi vagy kézi fugamaróval megfelelő mélységben és szélességben kimarjuk, és a fugát az esetleges szennyeződésektől megtisztítjuk. A hegesztést végezhetjük automata vagy kézi hegesztő készülékkel.A beállítandó hőmérséklet kb. 300 ºC, azonban az optimális hőfok és sebesség megállapításához minden esetben próbahegesztést kell végezni. Kör keresztmetszetű Grabo Weld felhasználá-sa esetén a felesleges zsinórt a hegesztési varrat kihű-lését követően, két lépésben távolítjuk el: először letoló szán és „negyedhold” kés segítségével a zsinórt félbevágjuk, majd a teljes kihűlést követően „negyedhold” késsel végezzük a síkba vágást.
HEGESZTÉS
WELD
1 2 3 4
WELDGraboplastFloor Covering Manufacturers Ltd.H-9023 Győr, Fehérvári út. 16/b.Telefon: (+36) 96 506-100
www.graboplast.com
The glued floorcovering should be grooved at the joints mechanically or manually in an adequate depth and width. Any contamination should be removed. Welding should be made either by automatic or manual welding machine. The recommended temperature is 300 ºC, but in order to set the optimal temperature and speed, test welding should be made in all cases. When applying round-diameter welding rod, the surplus, after the weld seam is cooled off should be removed in 2 steps: first the cord is cut into half by the help of a trimming guide and a quarter moon knife. Then, after total cooling off, the balance is cut to flat by a quarter moon knife.
WELDING
El fresado de las juntas del pavimento se puede realizar con maquina fresadora mecánica o manual, con la profundidad y anchura adecuadas, limpiando la hendidura resultante de posibles restos. Podemos hacer la soldadura con un soldador automáti-co o manual. La temperatura del soldador debe ajustarse normalmente entre 300 centigados, pero para establecer la temperatura y velocidad óptimas, es necesario realizar previamente unde prueba. En caso del soldar con cordon graboWeld de sec-cion circular, debe eliminarse el cordon sobrante cortando a ras de pavimento con una cuchilla tipo “cuarto de luna” una vezque el cordon se haya enfriando totalmente.
SOLDADURA
A leragasztott padlóburkolót az illesztéseknél gépi vagy kézi fugamaróval megfelelő mélységben és szélességben kimarjuk, és a fugát az esetleges szennyeződésektől megtisztítjuk. A hegesztést végezhetjük automata vagy kézi hegesztő készülékkel.A beállítandó hőmérséklet kb. 300 ºC, azonban az optimális hőfok és sebesség megállapításához minden esetben próbahegesztést kell végezni. Kör keresztmetszetű Grabo Weld felhasználá-sa esetén a felesleges zsinórt a hegesztési varrat kihű-lését követően, két lépésben távolítjuk el: először letoló szán és „negyedhold” kés segítségével a zsinórt félbevágjuk, majd a teljes kihűlést követően „negyedhold” késsel végezzük a síkba vágást.
HEGESZTÉS
WELD
1 2 3 4
4,0 mm
GRABOWELD
We offer the 4.0 mm diameter circular welding rods to commercial floorings and to show floorings.
Recomendamos el cordón de soldadura Graboweld, de4,0 mm de diámetro, para pavimentos instados en lugares de uso comercial y pavimentos instalados para eventos en caso de uso continuado
A 4,0mm-es Grabo Weldet a közületi felhasználási területekrelerakott padlókhoz és a show padlókhoz ajánljuk.
2110
2000
2320
4000
2216
2233
2082
2066
2561
2255
1651
2131
2251
2243
9105
2538
2537
2171
7250
2250
1138
1008
1133
1121
1347
1360
1156
1230
1340
1174
1154
1172
1165
1246
1259
1855
1286
1281
1675
1991
2295
2940
2954
2942
2278
2879
9067
9113
9145
4954
3080
3072
3884
3086
3066
3925
3430
3328
2246
2374
3553
3392
3391
2482
8010
3642
2075
2229
2296
2659
3111
7235
7073
7246
7405
7410
7801
7830
7057
7087
7089
7017
7606
7143
7307
7316
7263
7567
7522
7439
3655
3648
4505
4970
4955
4269
4517
4387
5025
4738
6322
6101
6058
1452
1260
6353
6091
6083
6346
6108
6160
6161
6384
6110
6364
6331
6184
6396
6546
6277
6057
6308
6292
6312
5972
5969
6954
5945
5845
5068
13811
15491
15771
62931
12601
13341
16551
63461
16751
12601
12461
14521
18551
60911
75831
70931
63401
12391
12691
63461
16551
2062
2219
2209
2038
2149
1794
2492
3151
2519
2851
3328
3338
3151
1794
3925
3096
3086
3072
2561
2529
1991
6277
6470
6780
6269
7093
6346
6170
6160
6161
3553
3573
3648
4289
4387
4725
4738
4957
5945
6107
2000
2066
2038
2209
2216
2219
7373
7122
7143
7483
7493
7507
7533
7566
7100
7522
1347
1360
6322
1156
1281
1452
1286
1855
6091
1675
12851
12591
12601
15681
18551
60911
63961
19911
47381
74481
63461
68131
75832
K326GGRABO WELD
K65GGRABO WELD
CARGRABO WELD
I40GRABO WELD
I50GRABO WELD
4,5 mm
GRABOWELD
We offer the 4.5 mm diameter circular welding rodsto Sport floorings.
Recomendamos el cordón de soldadura Graboweld, de 4,5 mmde diámetro, para pavimentos deportivos.
A 4,5mm-es Grabo Weldet a Sport padlókhoz ajánljuk.
Length: 100mLength: 120m
WELDGraboplastFloor Covering Manufacturers Ltd.H-9023 Győr, Fehérvári út. 16/b.Telefon: (+36) 96 506-100
www.graboplast.com
The glued floorcovering should be grooved at the joints mechanically or manually in an adequate depth and width. Any contamination should be removed. Welding should be made either by automatic or manual welding machine. The recommended temperature is 300 ºC, but in order to set the optimal temperature and speed, test welding should be made in all cases. When applying round-diameter welding rod, the surplus, after the weld seam is cooled off should be removed in 2 steps: first the cord is cut into half by the help of a trimming guide and a quarter moon knife. Then, after total cooling off, the balance is cut to flat by a quarter moon knife.
WELDING
El fresado de las juntas del pavimento se puede realizar con maquina fresadora mecánica o manual, con la profundidad y anchura adecuadas, limpiando la hendidura resultante de posibles restos. Podemos hacer la soldadura con un soldador automáti-co o manual. La temperatura del soldador debe ajustarse normalmente entre 300 centigados, pero para establecer la temperatura y velocidad óptimas, es necesario realizar previamente unde prueba. En caso del soldar con cordon graboWeld de sec-cion circular, debe eliminarse el cordon sobrante cortando a ras de pavimento con una cuchilla tipo “cuarto de luna” una vezque el cordon se haya enfriando totalmente.
SOLDADURA
A leragasztott padlóburkolót az illesztéseknél gépi vagy kézi fugamaróval megfelelő mélységben és szélességben kimarjuk, és a fugát az esetleges szennyeződésektől megtisztítjuk. A hegesztést végezhetjük automata vagy kézi hegesztő készülékkel.A beállítandó hőmérséklet kb. 300 ºC, azonban az optimális hőfok és sebesség megállapításához minden esetben próbahegesztést kell végezni. Kör keresztmetszetű Grabo Weld felhasználá-sa esetén a felesleges zsinórt a hegesztési varrat kihű-lését követően, két lépésben távolítjuk el: először letoló szán és „negyedhold” kés segítségével a zsinórt félbevágjuk, majd a teljes kihűlést követően „negyedhold” késsel végezzük a síkba vágást.
HEGESZTÉS
WELD
1 2 3 4