VS-570-HDSDI - Marshall Electronics · VS-570-HDSDI IP Cameras can be connected in either 1 to 1...

User Manual ver.1.0

VS-570-HDSDI 2.0 Megapixel Speed Dome

JimLucas

Text Box

v1.0 10062010570

VS-570-HDSDI User Manual

2.0 Megapixel Speed Dome Manual

2/54

Safety Precaution

Make sure to turn off the power before installing VS-570-HDSDI. Do not install under the direct sunlight or in dusty areas. Make sure to use the product within the temperature and humidity specified in the specification. Do not operate the product in the presence of vibrations or strong magnetic fields. Do not put electrically conducting materials in the ventilation hole. Do not open the top cover of the product. It may cause a failure or electric shock on the

components. To prevent from overheating, make sure to keep the distance at least 10cm from the ventilation

hole. Make sure of proper voltage (220V/100V) before connecting the power.

We appreciate your purchasing VS-570-HDSDI. Before installing the product, please read the following with care.



3/54

Table of Content

1. Introduction ................................................................................................................................. 4

About this manual ..................................................................................................................... 4 Features ................................................................................................................................... 4 Product and Accessories .......................................................................................................... 7 Part Names and Functions ....................................................................................................... 8 System Connections ................................................................................................................. 9

2. Installation ................................................................................................................................. 12 DIP Switch Setup .................................................................................................................... 12 Installation Camera with Brackets ........................................................................................... 14 Wiring/Cabling & Connecting .................................................................................................. 16 Check if it works ..................................................................................................................... 19

3. System Operation ..................................................................................................................... 20 Remote Video Monitoring ....................................................................................................... 20 Initialization of IP address ....................................................................................................... 23

4. Remote Configuration ............................................................................................................... 24 Using Web Brower .................................................................................................................. 24 System Configuration ............................................................................................................. 25 Video Configuration ................................................................................................................ 29 Audio Configuration ................................................................................................................ 34 Network Configuration ............................................................................................................ 35 Serial Configuration ................................................................................................................ 40 Event Configuration ................................................................................................................ 42 PTZ Configuration .................................................................................................................. 45 Record Configuration .............................................................................................................. 49 User Configuration .................................................................................................................. 50 Camera Configuration ............................................................................................................ 52



4/54

1. Introduction About this manual This User Manual provides information on operating and managing the premium network camera, VS-570-HDSDI. The Manual includes instructions of installation, operation and configuration of VS-570-HDSDI

troubleshooting tips.

Features VS-570-HDSDI is a 2.0M PTZ network-based camera with remote live monitoring, audio monitoring and control via an IP network such as LAN, ADSL/VDSL, and Wireless LAN.

Camera • 1/3” 2Megapixel CMOS Image Sensor

• X10 optical zoom, x12 digital zoom

• True Day & Night (ICR)

Video • Highly efficient compression algorithm, H.264 & MJPEG support

• 18 kinds of compression and resolutions: CIF (352x240) - Full HD (1920x1080)

• Wide range of transmission rates: 32kbps ~ 8Mbps

• Various transmission modes: CBR, VBR

• Motion detection

• Composite video output

• HD-SDI video output (Option)

Audio • Multi-transmission mode: Simplex (VS-570-HDSDI Client PC or Decoder, Client PC or

Decoder VS-570-HDSDI), Full Duplex

Network

• Fixed IP & Dynamic IP (DHCP) support

• 1:1, 1:N support

• Multicasting

• Various types of Protocol support: TCP/IP, UDP, Multicast, DHCP, SMTP, HTTP, SNMP, RTP, RTSP



5/54

Serial Data • RS-485 support:

• Data pass-through mode: Serial data communication between VS-570-HDSDI and Decoder.

Sensor and Alarm • Supports direct connections of external sensor and alarm devices.

• Event Alarm notification.

• 2 alarm sensor Inputs and 2 alarm Output relays are available.

• If an external sensor is activated, camera can be set to move to the corresponding Preset position.

User Interface

• Diagnose and upgrade a through dedicated program called True Manager.

• System configuration using Internet Explorer

High Reliability • Reliable embedded system.

Powerful Pan/Tilt Functions • Max. 360/sec high speed Pan/Tilt Motion.

• Using Vector Drive Technology, Pan/Tilt motions are accomplished in the shortest path. As a result, the time to target view is reduced dramatically and the video on the monitor is very stable.

• When using a PTZ controller, the ultra slow speed of 0.05/sec is usefull for accurately moving the camera to a desired view. Additionally, the zoom-proportional pan/tilt movement improves the ability to follow a moving object.

Preset, Pattern, Swing, Group • MAX. 128 Presets are assignable and characteristics of each preset can be set up

independently.

• Max. 8 sets of Swing action can be stored. This enables you to move the camera repetitively between two preset positions with a designated speed.

• Max. 4 of Patterns can be recorded and played back. This enables to move camera to follow any trajectory operated by a joystick as closely as possible.

• Max. 8 sets of Group actions can be stored. This enables you to move camera repetitively with a combination of Preset or Pattern or Swing. A Group is composed of a maximum of 20 entities of Preset/Pattern/Swings.



6/54

PTZ(Pan/Tilt/Zoom) Control • With RS-485 communication, a maximum of 255 cameras can be controlled at the same time.

• Pelco-D or Pelco-P protocol can be selected as a control protocol in the current version of firmware.

Easy Installation and Perfect Outdoor Environment Compatibility • Fans and heaters are built into the camera enclosure for both hot and cold temperature

environments. Advanced mechanical design protects the camera from damaging water and dust.

• It is easy to install and maintain the camera with a cable channel built into the mountin brackets.



7/54

Product and Accessories

Note: Mount Brackets are optional.

Wall Mount Bracket Ceiling Mount Bracket

[Screws : Torx Screw M418, Hex Lag #1450] [Screws : Torx Screw M418, Anchor Bolt 3/8"70]

Main body & Dome Cover Accessories

Main Cable Wrench Driver 2EA of BNC

Cross LAN Cable Audio Cable CD



8/54

Part Names and Functions

• Dome Cover To protect the dome cover from scratches or dust Do Not Remove the protective vinyl from the dome before completing the installation process.

• DIP Switch Sets up camera ID and protocol.

• Drop Prevention Spring

This prevents the camera from dropping during installation and maintenance. After installing the Bracket, please connect the spring to the drop prevention hook of main body as shown in picture.

• Mounting Screw Hole

This hole is for screws that attach the main body to the mounting bracket.

• IP Reset Switch Reset the network configuration to the factory defaults. You will lose all the data that had been previously entered . To initialize the system to the factory default, press the reset button and hold for more than 5 seconds.

• LAN Port This is used for the Ethernet connection.

• Audio Port This is used for the audio in/out connection.

• Video (BNC) This is used for the HD-SDI video out.

• Main Connector This is used for connecting to the power wire, the RS-485 communication cable, and the alarm in/out connection cable.

①



9/54

System Connections

VS-570-HDSDI IP Cameras can be connected in either 1 to 1 connection where one VS-570-HDSDI

is connected to one PC client or a decoder system or, 1 to many connections where one VS-570-HDSDI can be connected to several PCs and decoder systems. The VS-101 video server can work as a video decoder which takes the data from a video server or IP camera, decodes and outputs analog or digital video, HDMI and HDSDI.

Topology

Generally, the VS-570-HDSDI and PC or a decoder is connected in 1-to-1 mode or 1-to many configuration.

1:1 Connection .

One VS-570-HDSDI is installed at a site where video images are transmitted. A PC or a decoder is installed at a central location to receive and view the video images on an analog monitor. Audio and serial data are transferred in either direction.

Site Remote Center (Decoder) Remote Center

Site Remote Center (PC SW)



10/54

or

or

or

1:N Connection .

In this configuration, a site can be monitored from many remote central locations. Although up to 64 PCs

or decoders can be connected to one VS-570-HDSDI, in the real network environment, network bandwidth can limit the maximum connections. Functionally, the central monitoring system (CMS) software provided can replace the decoder.

Multicast Mode

If the network supports multicasting, a large number of decoders can be used to receive video effectively

from a VS-570-HDSDI using a single streaming of video and audio. However, multicast mode is possible only when the network environment supports multicast.

Relay

Video and audio data can be retransmitted from one center to another center. This arrangement is useful when the network bandwidth to the site is limited and there is more than one center wanting to monitor the site.

Site Remote Center

Site Center 1(Decoder) Center 2 (Decoder)



11/54

CMS (Central Monitoring System)

CMS (Central Monitoring System) is a Window-based remote monitoring program used to monitor or control video, audio, and events in real time from several IP cameras or video servers. Please refer to the CMS User Manual for more detail.

Site Remote Center

Site Remote Center (Decoder) CMS



12/54

2. Installation

DIP Switch Setup When you control the camera through RS-485, before installation, you should set the DIP switches to

configure the camera ID, communication protocol.

Camera ID setup

ONON

1 2 3 4 5 6 7 8

ID numbers of each camera are set up using binary numbers.

See the examples shown below:

Switch 1 2 3 4 5 6 7 8

ID Value 1 2 4 8 16 32 64 128

ex) ID=5 On off On off off off off off

ex) ID=10 off On off On off off off off

The camera ID range is 1~255. The Camera ID must not be 0.

Factory default of Camera ID is 1.

Match the camera ID with Cam ID setting of your DVR or Controller to control the camera.



13/54

Communication Protocol Setup

1 2 3 4

ONON

Select the appropriate Protocol with DIP switch combination.

Switch State Protocol/Baud rate S0

(Pin 1) S1

(Pin 2) S2

(Pin 3)

OFF OFF OFF PELCO-D, 2400 bps

ON OFF OFF PELCO-D, 9600 bps

OFF ON OFF PELCO-P, 4800 bps

ON ON OFF PELCO-P, 9600 bps

Otherwise Reserved

If you want to control using a DVR or P/T controller, their protocol must

be identical to the camera otherwise, you can not control the camera.

Turn off the camera before adjusting the DIP switches. If you change the camera protocol by changing the DIP switches, the change will be effective after you reboot the camera.

Factory default of protocol is “Pelco-D, 2400 bps”.



14/54

Camera Installation using Brackets

Installation using a Ceiling Mount Bracket (not supplied) ① Remove the ceiling tile from the ceiling and cut a hole whose diameter is 30~40mm on the ceiling tile to pass the wire(s) and cable(s) through to the upside of the ceiling. Then prepare the ceiling mount bracket. Pull the wire(s) for the system as below. (Anchor Bolt 3/8"×70)

② Hook up the “Drop Prevention Spring” on main body

to prevent the camera from unexpected drops. Pull

the wire(s) and cable(s) for the system as shown below.

③ Align the index marks and assemble the main

body to the mounting adaptor and turn it. Attach the main body to the camera mounting adaptor with the included screws. (Torx screw M4X18). Please make certain the screws are securely or tightened to maintain a waterproof seal.

④ Screw the dome cover to the main body and remove the protection vinyl from the dome cover.

Notice Before starting the installation, make sure that the Camera ID and Protocol are set up properly.

To adjust the installation height from the mounting surface, pipes and couplers may be needed

between the surface mount part of the ceiling mount bracket and the camera mount part of the ceiling

mount bracket. Please note that these are not supplied by the manufacturer.



15/54

Installation using the Wall Mount Bracket ① Make a hole whose diameter is 30~40mm on the mounting surface to pass the wire(s) and cable(s) through the mounting surface.

Prepare the wall mount bracket by Pulling the wire(s) and cable(s) for the system as below. Attach the wall mount bracket to the mounting surface. (Hex Lag #14×50)

② Hook up the “Drop Prevention Spring” on main body to

prevent the camera from unexpected drops. Pull the

wire(s) and cable(s) for the system as below.

③ Line up the index marks and assemble the main

body to the mounting ring and turn it. Attach the

main body to the mounting adaptor with the supplied

(Torx screw M4X18). Please make certain the screws

are securely tightened to maintain a waterproof seal. .

④ Screw the dome cover to the main body and

remove the protection vinyl from the dome.

Notice Before starting the installation, make sure that the Camera ID and Protocol are set up properly.



16/54

Wiring/Cabling & Connecting

Port Description Main Cable

Port Pin Number (RJ45) Connector / Wire Color Signal

1 Black RS485 +

2 Brown RS485

3 Red DC 12V

4 Orange Ground

5 Yellow OUT COM (Relay Output Common)

6 Green OUT 2 (Relay Output 2)

7 Blue OUT 1 (Relay Output 1)

8 Violet IN COM (Sensor Input Common)

9 Gray IN 1 (Sensor Input 1)

10 White IN 2 (Sensor Input 2)

Audio Cable

Port Pin Number Connector/ Wire Color Signal

1 RCA (Yellow) Audio IN

2 Audio GND

3 RCA (White) Audio OUT



17/54

Connecting Power

1. Carefully check the voltage and current capacity of the rated power. The rated power is indicated in the back of main unit.

2. After confirming the voltage, connect the power adaptor to the AC power source then connect the 12V DC connector to the system .

For the DC input models, be careful with the polarity of the DC power. The system will be

permanently damaged if connected to reverse polarity power supplies.

In cases where the power wire is very long, there may be a voltage drop and the system

may not work properly. Make the length of the power wire as short as possible.

Connecting Network

1. Plug thne network cable to Ethernet port (RJ-45 network port).

Connecting Video

1. To display video through the HD-SDI port, connect the port to a monitor using a BNC coaxial cable rated for HDSDI video.

2. Set Enable Preview option “ON” on the Video tab of web page.

(Please refer to the Video Configuration part of this manual)

When using HD-SDI, video may contain errors if the correct type of BNC coaxial cable is not used.

If the video transmission distance exceeds 100 meters, video data may lost due to a

reduction in the video signal. In order to prevent this use of a repeater is recommended.

When using HD-SDI, video can be only be viewed on a HD-SDI monitor.

Connecting Audio

Audio is full-duplex. It is possible to set the mode as Tx-only, Rx-only or Tx-Rx.

1. Connect the audio input and output ports to the corresponding audio devices.

2. The Audio signal required is line level. Audio equipment using an amp, mixer or other amplifier

should be used.



18/54

Connecting Serial Port (RS-485 Communication)

For PTZ control, connect the cable(s) to your keyboard or DVR. To connect multiple cameras to a single controller, the RS-485 communication should be connected in parallel as shown below. If you are connecting a single camera to a controller, you must terminate the camera. When connecting more than one camera to a single controller, terminate the last camera on the communication line. era The last camera means the camera farthest in cable length from the controller. Note that the total length of the communication cable between a controller and the camera(s) on the same communication t line must be less than 1.2Km.

The RS-485 port of VS-570-HDSDI can be connected to external equipment such as PT receiver etc. A PC client can send PT commands to the external equipment via the serial port.

When a decoder system instead of a PC client is connected to VS-570-HDSDI, the serial port and that of the decoder system work in pass-through mode. That is, data from one port is delivered to the other port and vice versa.

Connecting Sensor and Alarm

Connect sensor and alarm devices to corresponding terminals accordingly.

Sensor Input



19/54

Relay Output

Maximum allowable electrical load of relay is shown bellow table.

Drive Power DC Power AC Power

Max. Load Max DC 24V, 1A Max AC 125V, 0.5A

Check if it works

Once the power is supplied to the camera, it will start booting. The system will boot up to an operating mode after approximately 40-60 seconds. The green LED on the Ethernet port will flash indicating the system is ready.

The software provided in the CD called True Manager allows you to check the IP address and other network details of the camera. Please refer to the True Manager manual for instructions on how to find the IP address of the camera and change it if required.

OUT 1

AC or DC

LOAD

Internal

OUT 2 LOAD

OUT COM



20/54

3. System Operation

Remote Video Monitoring

There are two ways to monitor video when the center system and VS-570-HDSDI are connected. In order for proper operation, an IP address must be set accordingly. Please refer to True Manager in Chapter 3 or Remote Setting in Chapter 4 for further details.

Default ID : admin Default Password : 1234

.

Video Monitoring using Internet Explorer

Open Internet Explorer and enter VS-570-HDSDI‟s IP address. The system will ask for confirmation to install Active-X control. Once authorized, the Internet Explorer will start to display video images from VS-570-HDSDI as shown below.

Default IP Address : http://192.168.10.100



21/54

Video Selection

Select the Video stream to be viewed: Primary or Secondary.

The VS-570-HDSDI is capable of dual streaming; primary streaming and secondary streaming.

Video will be displayed according to the resolution set in the video configuration. If dual streaming (“Use Dual Encode” Menu on the Video page) is not activated, the secondary video will not be available.

Screen Size

Adjust the Screen size.

Screen size is initially adjusted according to the compression resolution. If you click on the x1/2 icon, the whole screen size will be reduced by half.

Digital Zoom

Controsl the Digital zoom on the screen.

The more the camera zooms in, the smaller the square of the control panel. Position of the image can be changed by moving the position of the square. Max x5 Digital Zoom is available. If you press x1, the screen will return to the normal size.

PTZ Control Panel (Optical Zoom & Digital zoom built-in the camera)

Control PTZ and PTZ Control Panel is used for controlling external PTZ devices when the external PTZ devices are connected through a serial port. Since x10 optical zoom lens and x12 digital zoom is built into the VS-570-HDSDI, it is possible to control zooming by using the Zoom in/out buttons of the PTZ control Panel. In order to use digital zoom, select Digital zoom ON in the Camera tab.

Focus Near, Focus Far, Auto Focus

Adjusts the focus of the lens.

Menu On, Enter, ESC

Displays and controls OSD (On Screen Display) menu if OSD menu is supported.

NOTE: The VS-570-HDSDI does not support the OSD menu.



22/54

Select Preset

Set the preset position, move to the specific preset position or clear the preset position.

- Go to: Moves to the selected preset entry if the preset entry is set.

- Set: Sets the current position to the selected preset entry.

- Clear: Deletes the selected preset entry.

Select List

Operate the selected Pattern or Swing or Group.

(Please refer to the PTZ tab to set Pattern, Swing and Group)

Sensor Input

Displays the status of the installed sensors in real time.

The VS-570-HDSDI supports two sensor inputs. When the sensor(s) of VS-570-HDSDI are installed and working, the sensor light turns red.

Alarm Output

Operates the alarm device by pressing the number icon

VS-570-HDSDI supports two alarm outputs. A number icon indicates the status of the alarm device.

Screen Capture

Captures video images and stores them as BMP or JPEG files.

Audio Transfer

Transfer audio from a PC that is displaying the current video image to VS-570-HDSDI.

File record

Recording the video appearing on the Live view page to an AVI file is available. The AVI files are generated

in the specified folder or in a specified file name on the PC where web browser is running.

1. Enter the drive and the folder name on the PC and enter the AVI

file name to be used.

2. Press the “Start” button to begin recording.

3. Press “Stop” button to end recording.

4. AVI file named “File name_IP address_hh_mm_ss” will be generated in the specified folder.



23/54

Video Monitoring with Decoder System

Once the VS-570-HDSDI‟s IP address is set in the remote IP address section of the decoder, the decoder system will connect to VS-570-HDSDI and start receiving the video images. Normally, a monitor connected to the decoder will display video images.

Initialization of IP address

If a system IP address is lost, the system can be reset to the system default IP address using the reset button in the rear of the system.

1. While the system is in operation, press and hold the reset button for more than 5 seconds.

2. The system will automatically reboot.

3. Once the system reboots, the IP address will be set to the system default as below:

IP mode Fixed IP IP address 192.168.10.100

Subnet mask 255.255.255.0 Gateway 192.168.10.1

Base port 2222 HTTP port 80



24/54

4. Remote Configuration

Using Web Brower

Remote setting is available by using the web browser. Enter the IP address of a VS-570-HDSDI, a live view screen appears as below. Press the Setup button located in the upper right area of the monitoring screen to go to the server setup. To change Remote Settings, the user must be authorized higher than manager level.

The configurations are grouped into 10 categories: System, Video, Audio, Network, Serial, Event, PTZ, Record, User and Camera. Configuration changes are not applied until the Apply button is pressed. If you leave the page without pressing the Apply button, any changes made on the page will not be saved.

Enter IP Address

Press Setup button



25/54

System Configuration



26/54

General System ID

Enter the System ID that will be used as the camera title.

The set System ID will be displayed with video image on the web browser. The System ID is

also transferred to remote software, such as CMS, and displayed on it.

Language

Select the language to be used for web-based configuration.

Firmware Firmware version

Displays the current firmware version.

Board ID

Display the Network board ID of VS-570-HDSDI recognized by system.

Upgrade

Upgrade firmware :

1. Press the Browse button to select a firmware file from your PC.

2. Press the Firmware Upgrade button to start the upgrade.

3. Messages showing the status (downloading / upgrading) will be displayed.

4. The camera will reboot automatically after completing the upgrade. Do not turn the camera off

during the upgrade process.



27/54

Time Start Time

This is the date and time when the camera was last booted.

Current Time

This is the current date & time.

Enter a new date and time and press the Set Current Time button to update.

Time Format

This allows you to change the time format. Selectable time formats are as follows:

- YYYY/MM/DD hh:mm:ss (Ex. 2010- 4-11 18:18:42)

- DD/MM/YYYY hh:mm:ss (Ex.11- 4-2010 18:18:42)

- MM/DD/YYYY hh:mm:ss (Ex. 4-11-2010 18:18:42)

Time Zone

This allows you to select the time zone of where the camera is installed.

Depending on the time zone, Daylight Saving Time will work automatically.

.

Automatically synchronize with NTP server

Checking this box will Synchronize the camera time with an NTP server using NTP (network time protocol).

Enter the NTP server name of the NTP server to be used.

Reboot Pressing this button will Reboot the camera.

Do not press the Reboot button unless required.

A time zone is a region of the earth that has uniform standard time, usually referred to as the local

time. By convention, time zones compute their local time as an offset from UTC (Coordinated

Universal Time). In casual use, GMT (Greenwich Mean Time) can be considered equivalent to UTC.

Local time is UTC plus the current time zone offset for the considered location.

The Network Time Protocol (NTP) is a protocol for synchronizing the clocks of computer systems

over packet-switched, variable-latency data networks. It is designed particularly to resist the effects

of variable latency by using a jitter buffer.



28/54

Factory Reset This changes the Current IP Address of VS-570-HDSDI to default IP Address: 192.168.10.100.

The System log and user registrations are also cleared. All other setting values will remain.

Note that the Password will not be changed by the Factory Reset for the security purpose. Please contact

Marshall Electronics Technical Support if you forget your password.



29/54

Video Configuration



30/54

Encode Enable Preview

1. Select ON to display video on the monitor that is connected to the composite or HD-SDI video port.

2. Select the Output format accordingly in the end of the Video page.

Note that when Enable Preview is ON, dual streaming is not available.

When the video is transmitted directly to the monitor through the BNC cable, the video signal bypasses the network and encoding.

Resolution

Select the video encoding resolution required.

18 resolutions are available.

The Scaling option is used when the encoding resolution is different from the input compression. Without

the Scaling option, input video will be croped according to the encoding resolution. On the other hand,

if Scaling is selected, the input video will be adjusted according to the encoding resolution.

Frame rate

Select the maximum number of frames per second for the video stream.

A frame rate of 1,2,3,4,5,6,8,10,15,20,25 and 30 can be selected. The actual frame rate of video can be less than the maximum frame rate set due to any network bandwidth limitation.

Preference

Select the encoding mode to control video quality: Quality or Bit rate.

If „Bit rate‟ is selected, the video encoding will be affected by the „Bit rate‟ value entered. Therefore, 'Bit rate' mode is CBR (Constant Bit rate) encoding.

If „Quality‟ is selected, the video encoding will be affected by the quality of image selected. Therefore, 'Quality' mode is VBR (Variable Bit Rate) encoding.



31/54

Quality

Select the required Video quality. Eight levels of quality are available.

Quality mode (VBR encoding) adjusts the bit rate according to the image complexity, using higher

bandwidth for increased activity in the video and lower bandwidth for decreased activity.

For active video content such as sports, or when network bandwidth is limited, It is reccomended

that CBR or Bit Rate encoding be used.

Bit rate

Set the bit rate value between 32 ~ 8000kbps.

Bit rate mode (CBR encoding) allows you to set a fixed bit rate that consumes a predictable amount of bandwidth. If the network capacity is sufficient use of a fixed bit rate of 4096 kbps or higher will maintain a high quality picture regardless of content.

I-Frame Interval

Set the I-frame Interval between 0 and 255.

There will be no I-frames if 0 is selected.

H.264 Profile

Select the H.264 Profile: High Profile or Baseline Profile

The standard defines various sets of capabilities which are referred to as profiles targeting specific classes of applications.

- High Profile (HiP)

The primary profile for broadcast and disc storage applications particularly for high-definition

television applications (for example, this is the profile adopted by the Blu-ray Disc storage format and

the DVB HDTV broadcast service).

- Baseline Profile (BP)

Primarily for low-cost applications that require additional data loss robustness, this profile is used in

some videoconferencing and mobile applications. This profile includes all features that are supported

in the Constrained Baseline Profile, plus three additional features that can be used for loss

robustness (or for other purposes such as low-delay multi-point video stream compositing).

http://en.wikipedia.org/wiki/Blu-ray_Disc

http://en.wikipedia.org/wiki/Digital_Video_Broadcasting



32/54

Dual Encode Use Dual Encode

1. Select the Off button on the Enable Preview to enable to use Dual Encode.

2. Select the ON button to enable to use Dual Encoding.

The secondary video can be viewed on Live View window by selecting Secondary on Video selection.

Dual Compression Algorithm

Select H.264 or MJPEG for the secondary streaming.

Maximum resolution is 1280 x 720 and 9 steps of resolution are available. If MJPEG is selected, only

“Quality” mode is supported

Motion Detection Use Motion Detection

Select ON to use the Motion Detection function.

Motion Detection Area Editing

Configure the regions for motion detection. Regions of arbitrary shapes can be configured using the

following steps:

Select the Enable button ajacent to the Edit heading .

Select editing Mode. Set is for including cells to motion detection region

and Erase is for excluding.

Select cells using the right mouse button. Multiple cells can be selected

conveniently by pressing and dragging.

Press Apply Edited Area to save the editing



33/54

Sensitivity

Sensitivity selects the amount of movement required to trigger (detect) a motion event.The value determines the sensitivity of the motion detection within a block. The lower the number the more sensitive to movement. Select from 0 to 10.

Information Display

System ID and/or server time can be display over the video window in Internet Explorer. Each item can be turned on or off separately, and the position also can be configured. This information is displayed after the video is decompressed.

Burn-in OSD

Inserts the system ID and date/time in the compressed video. The System ID and time respectively can be turned on or off in the video, the Position and Font size is also selectable.

Note: Since time information is inserted when the video is compressed, the changing characters of the time display is detected as motion. Therefore, even though there is no motion, an event will be triggered. In order to prevent this, exclude the area displaying time using Motion detection area editing.

Output Format Output Format menu appears only when Enable Preview is on.

Select the output format for the monitor preview according to the video output and monitor specification.



34/54

Audio Configuration

Algorithm Algorithm

Select the audio algorithm: G.711 or AAC.

Bitrate

Select the Bitrate to be 64kbps or 128kbps when AAC is selected.

The sampling rate is fixed to 32KHz when G7.11 is selected.

Note that when VS-570-HDSDI is connected to a decoder, the decoder ‟s audio algorithm MUST be set identically to transmit audio and video properly.

Mode Select the audio Transmit / Receive mode:

Mode Action

Off No operation

Tx-Only Transmit only

Rx-Only Receive only

Tx & Rx Transmit and Receive

Input Gain Set the audio input gain from 0 to 31.



35/54

Network Configuration



36/54

Local IP mode

Select the IP mode: Fixed IP or DHCP (Dynamic Host Configuration Protocol)

Depending on the mode selected, configuration items will appear as follows:

IP Mode Selection Description

Fixed IP

Local IP Fixed IP address

Local

Gateway

Gateway IP address

Local Subnet Subnet mask

DHCP N/A

☞ Please request IP address information from your ISP provider or network manager.

DNS Obtain DNS server address automatically.

Get DNS server address automatically when the IP mode is DHCP.

Use the following DNS server addresses:

Enter the DNS server IP address.

- Primary DNS server

- Secondary DNS server

Port Base Port

Enter the Base Port number.

The Network base port is used for communication between systems. In order for the VS-540-HDSDI and remote systems (decoder or CMS, NVR software) to be connected, the port numbers must be identically set.

Domain Name System (DNS) is a database system that translates a computer's fully qualified

domain name into an IP address. Networked computers use IP addresses to locate and connect to

each other, but IP addresses can be difficult for people to remember. For example, on the web, it's

much easier to remember the domain name www.amazon.com than it is to remember its

corresponding IP address (207.171.166.48). Each organization that maintains a computer network

will have at least one server handling DNS queries. That server, called a name server, will hold a list

of all the IP addresses within its network, plus a cache of IP addresses for recently accessed

computers outside the network.



37/54

HTTP Port

Enter the HTTP port used for web-based connection.

RTSP Port

Enter the RTSP port used for RTSP-based connection. The default RTSP port is 554.

RTSP (Real Time Streaming Protocol) is a standard for connected client(s) to control streaming data

over the World Wide Web.

Authentication RTSP Authentication

If the RTSP Authentication set to ON, the user must enter correct User ID and Password when any RTSP client is connected.

HTTP API Authentication

When HTTP API authentication set to ON, HTTP Authentication is asked for all clients which use

HTTP API .

RTP Session RTP (Real-Time Transport Protocol) is an Internet protocol used for transmitting single real-time

multimedia data such as audio and video to a select group of connected clients. Normally RTSP uses RTP to format packets of multimedia content. The RTP Session menu is used when only streaming the RTP without RTSP connection. The RTP stream will be transmitted to the destination set. The SDP (Session Description Protocol) file can be found in the server, and a client can retrieve it using http connection.

Related settings are as follows:

- Destination IP: Set the IP Address for your destination system which will receive RTP stream.

- Destination Port: Set the Port for your destination system which will receive RTP stream.

- User Name: Enter the User name that will be used as session name in the SDP file.

- File Name: Enter the file name that will be used as the name of the SDP file. It can then be accessed through http://ServerAddress/filename.

http://serveraddress/filename



38/54

SNMP The VS-570-HDSDI can be used as an SNMP agent. It is compatible to both SNMPv1 and

SNMPvec. Settings for using SNMP (Simple Network Management Protocol) are as follows:

- SNMP Listen Port: This port is used for connecting external devices when the system operates as an SNMP client. SNMP is not used when setting a 0 value.

- SNMP Trap Destination IP: Set the SNMP Trap Destination IP. - SNMP Trap Destination Port: Set the SNMP Trap Destination Port. SNMP is not used by setting 0

value.

Multicast Multicast IP

The multicast IP address selection range is between 224.0.1.0 and 238.255.255.255. The selection can be used only when media protocol is set to Multicast. The Multicast menu is used for the Multicast connection request from a decoder or CMS / NVR software to transmit Multicast stream to the decoder or CMS / NVR software. The multicast address must be the same for the system to be connected using multicast protocol.

DDNS Select the DDNS (Dynamic DNS) server to use. One of these two servers can be selected.

True DNS: TrueDNS service is used in this mode. Systems can be registered on the website for TrueDNS service: http://ns1.truecam.net. System will get a domain name of xxx.truecam.net style. Please, refer to the user guide document for True DNS service.

DynDNS: DynDNS service is used in this mode. Refer to www.dyndns.org for details. ID, Password and Domain name are needed when DynDNS is set.

Simple Network Management Protocol (SNMP) is used by network management systems to

communicate with network elements. SNMP lets TCP/IP-based network management clients use a

TCP/IP-based internetwork to exchange information about the configuration and status of nodes.

SNMP can also generate trap messages used to report significant TCP/IP events asynchronously to

interested clients. For example, a router could send a message if one of its redundant power supplies

fails or a printer could send an SNMP trap when it is out of paper.

Dynamic DNS is a method, protocol, or network service that provides the capability for a networked

device, such as a router or computer system using the Internet Protocol Suite, to notify a domain

name server to change, in real time (ad-hoc) the active DNS configuration of its configured

hostnames, addresses or other information stored in DNS.

http://ns1.truecam.net/

http://www.dyndns.org/



39/54

Check IP Disable: If “Check IP Disable” is selected, the IP Server will skip to check its own IP. In Fixed IP mode, the set IP will be registered on the DDNS server. In DHCP mode, the allotted IP will be registered on the DDNS server. Normally Check IP Disable can be unchecked.

Bitrate control When there is more than one client connected to the VS-570-HDSI, due to bandwidth differences

among the clients, some of them may not have enough bandwidth to receive the encoded stream completely. In this case, it is possible to select the way to stream video to clients as follows:

- Frame Drop Mode: Encoding will be adjusted to the client with the highest bandwidth. Clients with limited bandwidth may not receive all the frames.

- Suppression Mode: Bit rate and frame rate are adjusted most efficiently for all clients. In this case, all clients can be affected by the averaged bit rate and frame rate.

Address Info The following network information is displayed as Read only:

- IP Address: The Camera's own IP address. This information is useful when the camera‟s IP mode

is set to DHCP.

- Domain Name: If the camera is registered at the DDNS server, the registered domain name is

displayed.

- MAC Address: Display the MAC address of the camera. If the camera is registered at DDNS

server, the MAC address is used in DDNS registration.

- Connecting: Client IP Addresses that are currently connected to the system are listed. (1) Indicates

Primary Streaming and (0) Indicates Secondary streaming.



40/54

Serial Configuration



41/54

Serial Port Configuration Serial Port Information

RS-485 in VS-570-HDSDI support one RS-485 serial port.

The camera‟s serial port information is displayed automatically once the camera reboots after the DIP switch setup of the camera.

PTZ Type & ID: PTZ Type & ID are displayed automatically once the camera reboots after DIP switch setup. The default PTZ Type and ID is Pelco-D and 2400bps.

Sensor Type There are two sensor input ports on VS-570-HDSDI. The sensor ports can be configured as follows:

Function Operation

OFF Not used

NO (Normally

Open)

The port is normally open and activated when

closed.

NC (Normally

Closed)

The port is normally closed and activated

when opened.

The function of the sensor port is set based on the type of the sensor connected.

Sensor Schedule Choose Sensor OFF or Sensor ON. Click or drag the schedule cells below to set the Sensor

Schedule according to the day of the week and hour of the day.



42/54

Event Configuration



43/54

The VS-570-HDSDI has two sensor ports and two alarm ports.

When a decoder instead of a PC client is connected to a VS-570-HDSDI, one system becomes a Local system and the other a Remote system. Generally a system which is being used by the user is called the Local system. Then, actions for events can be configured for events from the remote system as well as for local system. For example, it is possible to turn on an alarm device in local (center) decoder system when a sensor device in remote (site) IP camera is triggered. Local section configures the actions for events from local (self) system, and configuration activates local devices. Remote sections configure the actions for events from the remote (peer) system.

The following table lists the possible actions for events.

Action Description

Alarm out Triggers alarm (relay) port.

E-mail Sends E-mail to the specified address. AVI file can be attached.

FTP Upload AVI file to a specified FTP server.

Preset Move to the Preset position.

Local & Remote Event Configuration Sensor1 / Sensor2/ Sensor3 / Sensor4.

Configures the actions when the sensor is activated. Multiple actions can be set for a single event.

On Video Loss

Configures the actions if the video input signal is lost. Multiple actions can be set for a single event.

On Motion

Configures the actions when motion is detected. Multiple actions can be set for a single event.

On Disconnect

Configures the actions when the link (connection) with peer system is disconnected. Multiple actions can

be set for a single event.

Alarm and Beep activation duration Set the duration of alarm or beep activation in case of an event. If it is set to continuous, it will remain

in an active state until an operator resets it manually.



44/54

E-mail Notification Specifies the information required to send event information, when E-mail is selected as an event action.

- Server Address: Enter an address of a mail (SMTP) server.

- Port: Specify a port for SMTP operation. Port 25 is the default port in SMTP operation. If a different port is configured in the SMTP server, this port needs to be changed accordingly.

- Sender Address: Enter an account registered in the SMTP server.

- ID & password: When the server requires authentication, ID and Password of an E-mail account need to be entered.

- Destination address: Enter the Destination address. More than one address can be entered by delimiting comma (,) or semi-colon (;). the Destination address can take up to 63 characters.

- Video Clip Attaching: Video clips stored at the moment of an event can be attached as an AVI or JPEG file format. If using dual Encoding, Primary video or Secondary video (H.264 only) can be selected.

FTP Upload Specifies the information to upload event information, when FTP is selected as an event action.

- Server Address: Enter an address of an FTP server to receive video files.

- Port: Specify a port for FTP operation. Port 21 is the default port in FTP operation. If a different port is configured in the FTP server, this port needs to be changed accordingly.

- ID & password: Enter ID and Password for accessing the FTP server.

- Upload video: Primary video and Secondary video (H.264 only), JPEG can be selected as an upload method.

- Number of Frame: Enter frame number of JPEG Capture (from 1 to 10)

- Continuous upload: Continuous upload “on” allows the video image to be transmitted regularly, regardless of the occurrence of events.

- Upload duration: Specify recording duration of a video clip to be transmitted. (Max 300 sec).

- Upload interval: Specify transmission interval. (Max 3600 sec).

Recording duration is not included in the transmission interval. For example, if Upload interval is 60 seconds and Upload duration is 20 seconds, a Video clip of 20 seconds is transmitted every 80 seconds.

Event Record Specify the duration of recorded video generated by events to send through E-mail or upload through FTP.

- Pre-event Time: Specify the duration of the recording before an event happens.

- Post-event Time: Specify the duration after the event is cleared.

Max duration is 30 seconds.



45/54

PTZ Configuration



46/54

PTZ Control PTZ using the PTZ controller

Preset A Maximum 128 positions can be stored as Preset positions.

1. Move the position to be set.

2. Select one of the entries of Preset from the list.

3. Press Set button.

4. Enter the preset name to be used and press Save Label button.

5. Press Go to button to move to the present position.

Pattern Pattern Function is that a camera memorizes the path (mostly curve path) by joystick of controller for

assigned time and revives the path exactly as it memorized. 4 Patterns are available and Maximum 760 communication commands can be stored in a pattern.

1. Select one of the entries of Pattern from the list.

2. Press Set Pattern Start button. Create the Pattern by using the PTZ controls. Every move will be saved until pressing the Set Pattern Stop button.

3. Press Set Pattern Stop button to save the pattern.

4. Press Run Pattern button to playback the selected pattern.

Note that when the system memorizes patterns, the commands are stored in the internal memory not

the in the Pan/Tilt/Zoom positions. Hence there might be small differences between the original path

and the replayed path by path patterns. Note that it is not a problem in position precision.



47/54

Swing By using Swing function, you can make camera to move between 2 Preset positions repeatedly. When

swing function runs, camera moves from the preset assigned as the 1st point to the preset assigned as the 2nd point in CW(Clockwise) direction. Then camera moves from the preset assigned as the 2nd point to the preset assigned as the 1st point in CCW(Counterclockwise) direction.

In case that the preset assigned as the 1st point is same as the preset assigned as the 2nd point, camera turns on its axis by 360 in CW(Clockwise) direction and then it turns on its axis by 360 in CCW(Counterclockwise) direction

.

1. Check Enable box

2. Select the Preset for 1st Position and 2nd Position

3. Enter the Speed (0~255)

4. Press Save Swing button to save the Swing

Group This function allows the camera to memorize a combination of Presets, Patterns and/or Swings as a

Group which can be sequentely run repetitively. A Maximum of 8 sets of Group are available to

program. Each group can have maximum of 20 actions which are the combination of Presets, Patterns

and Swings. Preset speed and the repeat number of Pattern & Swing can be set using the

Option entry. Dwell time between actions can be set up as well.

1. Select one of the Group entries.

2. Press Modify Group button. The following window will appear.

3. Set the Action (Preset or Swing or Pattern), Dwell Time and Option and check the Enable boxes.

4. Press Apply button. The Group can then be used on the Live View Page.



48/54

Ex) Group-1

5 10 3

Live View Page

Select List-1 and Press Group to playback the Group-1 program.

Swing-1 Repeat 2

Preset-1 Speed 3

Pattern-1 Repeat100



49/54

Record Configuration This page is not available from the VS-570-HDSDI

When using the VS-570-HDSDI the Record page is not available.



50/54

User Configuration

User List Users can be registered and the privilege level of each user can be specified. User configuration is

allowed only by the Admin user. A maximum of 16 users can be registered and each user can have one of four privileges:

Privilege Allowed Operations Remarks

Admin All operations User ID = admin

Manager All operations except for user

configuration

User Live viewing and PTZ control

Guest Live viewing only

Add User

Press the Add button. The following window will appear:

Enter the User ID and password (up to 15 characters) and select the allowed Privilege Level



51/54

Delete User

Select the User to be deleted and press the Delete button.

Change Password

Press Modify Password button. The following window will appear:

Enter the current password and then set a new password.

Modify Privilege Level

Press the Modify Privilege button to change theUser privilege level. It is not allowed to change the privilege level of the admin user.

Login Policy Authentication Type

For user login, the following access algorithms can be selected: Basic or Digest.

HTTP authentication based on RFC 2617 (HTTP Authentication: Basic and Digest Access

Authentication) is supported.

Skip Login provides for convenient access to the server when authentication is not required. When Skip Login is set to Enable, the login step is skipped. The privilege level in force after login skip is usedwill be determined by the setting of Privilege Level After Login Skipped.



52/54

Camera Configuration



53/54

Day & Night The camera delivers color images during the day. As light diminishes below a certain level, the camera

can automatically switch to night mode (Black & White mode) to maintain good image quality.

Day & Night function can be selectable according to the environment.

- Auto : Automatically switches to Day (Color) or Night (B&W) according to light using ICR (Infrared Cut filter Removable).

- Day (Color): Delivers a color image regardless of light.

- Night (B/W): Delivers a B/W image regardless of light.

White Balance White Balance has the following modes:

- Auto: This mode computes the white balance value output using color information from the entire screen. It outputs the proper value using the color temperature radiating from a black subject based on a range of values from 3000 to 7500K

- Manual: Manual allows control of R and B gain, 256 steps each.

Auto Exposure AE Mode

- Full Auto: Auto Iris and Gain, Fixed Shutter Speed (59.94/NTSC:1/60 sec, 50/PAL: 1/50 sec)

DSS (Digital Shutter Speed) mode (Auto or Off) can be selected. When DSS mode is Auto, from 1/2 to 1/60 DSS Limit is available. Back Light Compensation can be selected.

- Manual: 21 steps of Shutter, 18 steps of Iris and 8 steps of Gain can be set manually.

- Shutter Priority: 21 steps (1/2 ~ 1/10,000) of Shutter Speed can be set manually. The Iris and Gain are set automatically according to the brightness of the subject.

- Iris Priority: 18 steps (F1.8 to Close) of Iris can be set manually. The Shutter Speed and Gain are set automatically, according to the brightness of the subject.

- Bright: The bright control function adjusts both the Gain and Iris using an internal algorithm according to a brightness level set by the user. Exposure is controlled by Gain when dark and by Iris when bright. As both Gain and Iris are fixed, this mode is used when exposing at a fixed camera sensitivity.

- Spot Light: Avoids a situation where the face of the subject is over-illuminated, and becomes washed out. In Spot AE, a particular section of the subject can be designated, and then that portion of the image can be weighted and a value computed so that the Iris and Gain can be optimized to obtain an image.



54/54

ETC Digital Zoom

Determine the Digital zoom (12x) supported by the camera zoon lens.

x10 Optical zoom and x12 Digital zoom lens (f=5.1 ~ 5.1mm) is built-in VS-570-HDSDI.

Aperture Level

Set Aperture Level from 0 to 15.

Aperture control is a function which adjusts the enhancement of the edges of objects in the picture. There are 16 levels of adjustment, starting from “no enhancement.” When shooting text, this control may help by making the text sharper.

Zoom Proportional Jog

When Zoom proportional Jog is ON, the Pan/Tilt speed will be set automatically after Zoom in (x10)

Auto Flip

- ON: If the tilt angle arrives at the top of the tilt orbit(90°), the zoom module camera turns on its axis by 180° at the top of tilt orbit and moves to the opposite tilt direction (180°) to keep tracing targets.

- Off: More than 90° tilt moving is not available

Max Jog Speed

Adjust the Max Pan Speed (8 Steps)

Max Zoom Speed

Adjust the Max Zoom Speed (8 Steps)

JimLucas

Text Box

v1.0 10062010570

VS-570-HDSDI - Marshall Electronics · VS-570-HDSDI IP Cameras can be connected in either 1 to 1...

Documents

Transcript of VS-570-HDSDI - Marshall Electronics · VS-570-HDSDI IP Cameras can be connected in either 1 to 1...