VIKING · 2018-11-05 · Remote Trigger Switch/Button (momentary SPST not included) Step 1 Connect...
Transcript of VIKING · 2018-11-05 · Remote Trigger Switch/Button (momentary SPST not included) Step 1 Connect...
PRODUCT MANUALDesigned, Manufactured and Supported in the USA
C O M M U N I C AT I O N & S E C U R I T Y S O L U T I O N S
Promote Your Business WhileCustomers Hold and more ...
Features
The DVA-2WA is a digital announcer with a built in
2 watt amplifier. Designed to provide music and
promotion on hold, the DVA-2WA can playback in
a continuous loop or alternate between promotions
and an auxiliary music source in timed intervals.
Any number of multiple messages may be
recorded.
The announcer comes with four professionally pre-
recorded promotion on hold messages, a power
supply and cabling for an easy plug and play
installation.
The output of the DVA-2WA may also be
connected directly to loudspeakers for repeated
messages or played at the push of a button for
museum displays, information booths, point of
interest locations, retail applications, etc.
• 7.5 minutes of user recordable memory
• Select from user recorded messages or four pre-recorded
on-hold pacifier messages
• Three playback options: on demand, continuous loop and
timed intervals
• Non-volatile memory (no batteries required)
• Built-in 2 watt amplifier will drive up to three 25AE Paging
Horns, 30AE Ceiling Speakers or equivalent
• Record from electret mic, carbon handset, tape, CD, PC
sound card or any line level device
• Monitor recording from a standard handset
• 600 ohm audio output for high wattage amplifiers
• Multiple message capabilities (total number of messages
limited to 250 or the maximum record time)
• AGC (Automatic Gain Control) for trouble free recording
• Auxiliary audio (MOH) input for background music between
messages
• Remote trigger input for on-demand playback from a remote
contact closure
• Press and hold play mode
• Status LED for record and playback indication
• Master and auxiliary input volume controls
• I.O. (Input/Output) communications port (allows only one
DVA-2WA to announce at a time)
• On-hold promotion messages and background-music
• Non-volatile message repeater for...
- Museum and information displays
- Car rental “Leave the keys in the ignition...”- Airport “Loading and unloading only...”- Smoking “This is a non-smoking building...”- Amusement Parks “Please keep your hands in the vehicle at all times...”
- Retail “Blue light special in aisle 5...”
Power: 120V AC/12V DC, 500mA adapter provided
Dimensions: 5.25” x 3.5” x 1.75” (133mm x 89mm x 44mm)
Shipping Weight: 2.2 lbs (1.0 kg )
Environmental: 32°F to 90°F (0°C to 32°C) with 5% to 95%
non-condensing humidity
Frequency Response: 100-3.4KHz
Sampling Rate: 64K (equivalent)
User Message Length: 7.5 minutes maximum
Recording Audio Input Level: 30mV - 1.0V RMS (AGC
range)
600 Ohm Audio Output Level: 0.3V RMS maximum (across
a 600 ohm load)
Speaker Output Power: 2 watt peak
Connections: (1) 6-position cage clamp terminal block, (3)
3mm (1/8”) audio jacks, (1) handset jack
Pre-recorded Pacifier Message Length: 30 seconds total
Minimum Speaker Impedance: 2.66 Ohms: (3) 8-Ohm
speakers in parallel
I.O. Com Wire Run Length: 1000 ft maximum (24 AWG)
Remote Trigger Wire Run Length: 4000 ft maximum (24
AWG)
DVA-2WADigital Voice Announcer
with Built-In Amplifier
April 24, 2018
Applications
Specifications
www.VikingElectronics.com
Information: 715-386-8861
VIKING
The DVA-2WA’s non-volatile memory eliminates
the need for batteries or costly built in tape decks.
This provides the convenience of recording at the
shop or professional studio and then shipping to
the installation site.
2
Features Overview
C
C
MADE IN
USA
TPG
1 432
ON
1 765
VIKING©
VIKINGELECTRONICS
HUDSON WI, 54016
DIGITAL ANNOUNCERWITH 2 WATT AMPLIFIER
POW
ER 1
2V D
C
MODEL DVA-2WA MASTERVOLUME
AUX. AUDIOVOLUME
MIN MAX MIN MAX
1 2 3 4 5 6
600
OH
M A
UD
I OO
UTP
UT
SPEA
KER
OU
TPU
T
MES
SAG
E R
EPEA
TD
ELAY
TIM
ES
HA
ND
SET
REC
/ M
ON
ITO
R
REC
OR
D A
UD
I OIN
PUT
( MIC
/ TA
PE)
AU
X. A
UD
IOIN
PUT
/ MO
H
3 4 1 2 5 6 7
MIC
ATT
ENU
ATIO
NA
UTO
REP
EAT
REM
OTE
TR
I GG
ER
PRES
S A
ND
HO
LD
DEF
AU
LT M
ESSA
GE
STAT
US
- PW
R
STA
RT
/ STO
P
Master Volume Control: Adjusts audio output level of messages and auxiliary/ MOH audio.
Record and Playback Start/Stop Button: For starting and stopping recording and/or playback.
Handset Record/Monitor Jack: Only a carbon type handset can be used for recording. Any standard handset may be used for monitoring.
Record Audio Input Jack: For electret Mic or line level audio input from tape, CD, PC, etc. (1/8” mono jack)
Auxiliary Audio Volume Control: Adjust to match background music volume to message volume.
600 Ohm Audio Output: Connect to music input port of phone system or higher watt amplifier. (1/8” mono jack)
I.O. (Input/Output) Com Port:Daisy-chain terminals A & B to multiple DVA-2WA’s.With this connection made, the last DVA-2WA activated will turn off the current announcement of any previous DVA-2WA and allow only the last DVA-2WA activated to be heard. Note: This connection is polarity sensitive.
Amplified Speaker Output:Connect directly to speakers. Up to three 8-Ohm speakers maximum.
Remote Trigger Input: Connect to a momentary contact closure for single on-demand playback.
Programming Switches: Set message repeat times and unit configurations (see page 9).
Auxiliary Audio/MOH Input: For timed background music between promotional messages. (1/8” mono jack)
Status LED: Indicates which function the DVA-2WA is currently performing. See the chart below for function descriptions.
PLAY/RECORD Selector Switch: Move switch to the left to select the play mode. Move switch to the right to select the record mode.
Important: If you experience hum during the playback of user-recorded messages, earth ground Speaker Output terminal 5 before recording messages.
IMPORTANT: Electronic devices are susceptible to lightning and power station electrical surges from both the ACoutlet and the telephone line. It is recommended that a surge protector be installed to protect against such surges.
Status Function
OFF Idle
ON Steady Ready to record
Fast Flash Recording
Flash Playback
Slow Flash Delay time
Pulse Hi/Lo Memory overflow
3
C
C
MADE IN
USA
TPG
1 432
ON
1 765
VIKING©
VIKINGELECTRONICS
HUDSON WI, 54016
DIGITAL ANNOUNCERWITH 2 WATT AMPLIFIER
POW
ER 1
2V D
C
MODEL DVA-2WA MASTERVOLUME
AUX. AUDIOVOLUME
MIN MAX MIN MAX
1 2 3 4 5 6
600
OH
M A
UD
IOO
UTP
UT
SPEA
KER
OU
TPU
T
MES
SAG
E R
EPEA
TD
ELAY
TIM
ES
HA
ND
SET
REC
/ M
ON
ITO
R
REC
OR
D A
UD
IOIN
PUT
(MIC
/ TA
PE)
AU
X. A
UD
IOIN
PUT
/ MO
H
3 4 1 2 5 6 7
MIC
ATT
ENU
ATIO
NA
UTO
REP
EAT
REM
OTE
TR
IGG
ER
PRES
S A
ND
HO
LD
DEF
AU
LT M
ESSA
GE
STAT
US
- PW
R
C
C
MADE IN
USA
TPG
1 432
ON
1 765
VIKING©
VIKINGELECTRONICS
HUDSON WI, 54016
DIGITAL ANNOUNCERWITH 2 WATT AMPLIFIER
POW
ER 1
2V D
C
MODEL DVA-2WA MASTERVOLUME
AUX. AUDIOVOLUME
MIN MAX MIN MAX
1 2 3 4 5 6
600
OH
M A
UD
I OO
UTP
UT
SPEA
KER
OU
TPU
T
MES
SAG
E R
EPEA
TD
ELAY
TIM
ES
HA
ND
SET
REC
/ M
ON
ITO
R
REC
OR
D A
UD
I OIN
PUT
( MIC
/ TA
PE)
AU
X. A
UD
IOIN
PUT
/ MO
H
3 4 1 2 5 6 7
MIC
ATT
ENU
ATIO
NA
UTO
REP
EAT
REM
OTE
TR
I GG
ER
PRES
S A
ND
HO
LD
DEF
AU
LT M
ESSA
GE
STAT
US
- PW
R
STA
RT
/ STO
P
STA
RT
/ ST O
P
OR
ON
OFF1 432 765
Continuous Recorded Loop Music(DIP Switch 6 ON)
DIPSwitches
KSU or PABXPhone System
To Music OnHold Input
Double ended 1/8”audio cord included
Licensed Radio
12V DCAdapter
(included)
120V AC
see page 9
Installation
A. Pre-Recorded or User-Recorded Promotion and Music On Hold
In this application, the DVA-2WA will play a continuous loop to your phone system’s music-on-hold port.
B. Information On-Demand
1. On-Demand with Uninterruptible Announcement
This application is ideal for situations in which a momentary contact closure will trigger the
announcement or message. Once triggered, the unit will play its entire message. When the
message has finished, the switch can be activated again to play the next message (or repeat
the first message if only one is recorded).
C
C
MADE IN
USA
TPG
1 432
ON
1 765
VIKING©
VIKINGELECTRONICS
HUDSON WI, 54016
DIGITAL ANNOUNCERWITH 2 WATT AMPLIFIER
POW
ER 1
2V D
C
MODEL DVA-2WA MASTERVOLUME
AUX. AUDIOVOLUME
MIN MAX MIN MAX
1 2 3 4 5 6
600
OH
M A
UD
I OO
UTP
UT
SPEA
KER
OU
TPU
T
MES
SAG
E R
EPEA
TD
ELAY
TIM
ES
HA
ND
SET
REC
/ M
ON
ITO
R
REC
OR
D A
UD
I OIN
PUT
( MIC
/ TA
PE)
AU
X. A
UD
IOIN
PUT
/ MO
H
3 4 1 2 5 6 7
MIC
ATT
ENU
ATIO
NA
UTO
REP
EAT
REM
OTE
TR
I GG
ER
PRES
S A
ND
HO
LD
DEF
AU
LT M
ESSA
GE
STAT
US
- PW
R
STA
RT
/ STO
P
Remote Trigger Switch/Button(momentary SPST not included)
Step 1 Connect speakers to the DVA-2WA as shown in the diagram below.
Step 2 Connect a “Remote Trigger Switch/Button” (momentary SPST, not included).
*
* Note: Up to three 8-ohm speakers may be connected (not included). Viking models 25AE Paging Horn,30AE Ceiling Speaker or equivalent are recommended. For more information, see DOD 498.
C
C
MADE IN
USA
TPG
1 432
ON
1 765
VIKING©
VIKINGELECTRONICS
HUDSON WI, 54016
DIGITAL ANNOUNCERWITH 2 WATT AMPLIFIER
POW
ER 1
2V D
C
MODEL DVA-2WA MASTERVOLUME
AUX. AUDIOVOLUME
MIN MAX MIN MAX
1 2 3 4 5 6
600
OH
M A
UD
I OO
UTP
UT
SPEA
KER
OU
TPU
T
MES
SAG
E R
EPEA
TD
ELAY
TIM
ES
HA
ND
SET
REC
/ M
ON
ITO
R
REC
OR
D A
UD
I OIN
PUT
( MIC
/ TA
PE)
AU
X. A
UD
IOIN
PUT
/ MO
H
3 4 1 2 5 6 7
MIC
ATT
ENU
ATIO
NA
UTO
REP
EAT
REM
OTE
TR
I GG
ER
PRES
S A
ND
HO
LD
DEF
AU
LT M
ESSA
GE
STAT
US
- PW
R
STA
RT
/ STO
P
Remote Trigger Switch/Button(momentary SPST not included)
Remote Stop Switch/Button(momentary SPST not included)
4
Step 1 Connect speakers to the DVA-2WA as shown right.
Step 2 Use the “Remote Trigger Switch/Button” for the “Start” Switch.
Step 3 Use the optional Remote Stop Switch on the I.O.COM connections A & B for the “Stop“ Switch.
3. On-Demand with interruptible Announcement (Separate Start/Stop Switches/Buttons)
This application is ideal for situations in which separate switches or buttons are used to start or
stop the message.
*
* Note: Up to three 8-ohm speakers may be connected (not included). Viking models 25AE Paging Horn,30AE Ceiling Speaker or equivalent are recommended. For more information, see DOD 498.
2. On-Demand with Uninterruptible Announcement (Single Start/Stop Switch/Button)
This application is ideal for situations in which a single switch or button is used to start or stop
the message.
C
C
MADE IN
USA
TPG
1 432
ON
1 765
VIKING©
VIKINGELECTRONICS
HUDSON WI, 54016
DIGITAL ANNOUNCERWITH 2 WATT AMPLIFIER
POW
ER 1
2V D
C
MODEL DVA-2WA MASTERVOLUME
AUX. AUDIOVOLUME
MIN MAX MIN MAX
1 2 3 4 5 6
600
OH
M A
UD
I OO
UTP
UT
SPEA
KER
OU
TPU
T
MES
SAG
E R
EPEA
TD
ELAY
TIM
ES
HA
ND
SET
REC
/ M
ON
ITO
R
REC
OR
D A
UD
I OIN
PUT
( MIC
/ TA
PE)
AU
X. A
UD
IOIN
PUT
/ MO
H
3 4 1 2 5 6 7
MIC
ATT
ENU
ATIO
NA
UTO
REP
EAT
REM
OTE
TR
I GG
ER
PRES
S A
ND
HO
LD
DEF
AU
LT M
ESSA
GE
STAT
US
- PW
R
STA
RT
/ STO
P
Remote Start/Stop Switch/Button(momentary SPST not included)
Step 1 Connect speakers to the DVA-2WA as shown right.
Step 2Solder a momentary SPST switch/button to the “REMOTE SW” pads 1 & 2. This will allow
users to start and stop messages from a single remote switch.
*
* Note: Up to three 8-ohm speakers may be connected (not included). Viking models 25AE Paging Horn,30AE Ceiling Speaker or equivalent are recommended. For more information, see DOD 498.
5
Step 1
Adjust DIP switches 2, 3 and 4 for delay
times of 2 seconds to 30 minutes (see
page 9).
Step 2
Connect speakers or auxiliary amplifier.
The Unit will power up to three 8-ohm
speakers, or can provide a 600 ohm signal
to auxiliary amplifiers.
Step 3Set DIP switch 6 to the ON position for
continuously repeated playback
C
C
MADE IN
USA
TPG
1 432
ON
1 765
VIKING©
VIKINGELECTRONICS
HUDSON WI, 54016
DIGITAL ANNOUNCERWITH 2 WATT AMPLIFIER
POW
ER 1
2V D
C
MODEL DVA-2WA MASTERVOLUME
AUX. AUDIOVOLUME
MIN MAX MIN MAX
1 2 3 4 5 6
600
OH
M A
UD
I OO
UTP
UT
SPEA
KER
OU
TPU
T
MES
SAG
E R
EPEA
TD
ELAY
TIM
ES
HA
ND
SET
REC
/ M
ON
ITO
R
REC
OR
D A
UD
I OIN
PUT
( MIC
/ TA
PE)
AU
X. A
UD
IOIN
PUT
/ MO
H
3 4 1 2 5 6 7
MIC
ATT
ENU
ATIO
NA
UTO
REP
EAT
REM
OTE
TR
I GG
ER
PRES
S A
ND
HO
LD
DEF
AU
LT M
ESSA
GE
STAT
US
- PW
R
STA
RT
/ STO
P
To input of pagingamplifier (not included)
ON
OFF1 432 765
DIPSwitches
see page 9
C. Continuous Loop (Repetitive Information)
Single or multiple informational messages may
be repeated continuously or you may use the
message repeat delay time option for adding
timed intervals between messages.
*
* Note: Up to three 8-ohm speakers may be connected(not included). Viking models 25AE Paging Horn, 30AECeiling Speaker or equivalent are recommended. Formore information, see DOD 498.
C
C
MADE IN
USA
TPG
1 432
ON
1 765
VIKING©
VIKINGELECTRONICS
HUDSON WI, 54016
DIGITAL ANNOUNCERWITH 2 WATT AMPLIFIER
POW
ER 1
2V D
C
MODEL DVA-2WA MASTERVOLUME
AUX. AUDIOVOLUME
MIN MAX MIN MAX
1 2 3 4 5 6
600
OH
M A
UD
I OO
UTP
UT
SPEA
KER
OU
TPU
T
MES
SAG
E R
EPEA
TD
ELAY
TIM
ES
HA
ND
SET
REC
/ M
ON
ITO
R
REC
OR
D A
UD
I OIN
PUT
( MIC
/ TA
PE)
AU
X. A
UD
IOIN
PUT
/ MO
H
3 4 1 2 5 6 7
MIC
ATT
ENU
ATIO
NA
UTO
REP
EAT
REM
OTE
TR
I GG
ER
PRES
S A
ND
HO
LD
DEF
AU
LT M
ESSA
GE
STAT
US
- PW
R
STA
RT
/ STO
P
C
C
MADE IN
USA
TPG
1 432
ON
1 765
VIKING©
VIKINGELECTRONICS
HUDSON WI, 54016
DIGITAL ANNOUNCERWITH 2 WATT AMPLIFIER
POW
ER 1
2V D
C
MODEL DVA-2WA MASTERVOLUME
AUX. AUDIOVOLUME
MIN MAX MIN MAX
1 2 3 4 5 6
600
OH
M A
UD
I OO
UTP
UT
SPEA
KER
OU
TPU
T
MES
SAG
E R
EPEA
TD
ELAY
TIM
ES
HA
ND
SET
REC
/ M
ON
ITO
R
REC
OR
D A
UD
I OIN
PUT
( MIC
/ TA
PE)
AU
X. A
UD
IOIN
PUT
/ MO
H
3 4 1 2 5 6 7
MIC
ATT
ENU
ATIO
NA
UTO
REP
EAT
REM
OTE
TR
I GG
ER
PRES
S A
ND
HO
LD
DEF
AU
LT M
ESSA
GE
STAT
US
- PW
R
STA
RT
/ STO
P
Optional I.O. COM Connections
Note: This connectionis polarity sensitive
Optional Remote Stop Switch/Button(momentary SPST not included)
To otherDVA-2WA
units
Step 1Connect speakers and remote momentary switches to the DVA-2WAs as shown in Installation
sections 1, 2 or 3.
Step 2Connect the I.O. Com connections as shown below to prevent two announcers from playing at
one time.
Step 3A remote “stop” switch can be connected to the I.O Connections A & B. A momentary closure
will stop message.
4. Multiple Units with I.O. (Input/Output) Communication
When installing multiple DVA-2WA’s in displays that are close enough together to cause audible
interference, the I.O. communication will allow only one DVA-2WA to announce at a time. The
last unit to be triggered will announce its message, disabling any current messages played
from any previously triggered DVA-2WA.
*
* Note: Up to three 8-ohm speakers may be connected (not included). Viking models 25AE Paging Horn,30AE Ceiling Speaker or equivalent are recommended. For more information, see DOD 498.
6
E. Time Activated Messages Over a Paging System
C
C
MADE IN
USA
TPG
1 432
ON
1 765
VIKING©
VIKINGELECTRONICS
HUDSON WI, 54016
DIGITAL ANNOUNCERWITH 2 WATT AMPLIFIER
POW
ER 1
2V D
C
MODEL DVA-2WA MASTERVOLUME
AUX. AUDIOVOLUME
MIN MAX MIN MAX
1 2 3 4 5 6
600
OH
M A
UD
I OO
UTP
UT
SPEA
KE R
OU
TPU
T
MES
SAG
E R
EPEA
TD
ELAY
TIM
ES
HA
ND
SET
REC
/ M
ON
ITO
R
REC
OR
D A
UD
IOIN
PUT
(MIC
/ TA
PE)
AU
X. A
UD
IOIN
PUT
/ MO
H
3 4 1 2 5 6 7
MIC
ATT
ENU
ATIO
NA
UTO
REP
EAT
RE M
OTE
TR
IGG
E R
PRES
S A
ND
HO
LD
DEF
AU
LT M
ESSA
GE
STAT
US
- PW
R
STA
RT
/ STO
P
|OR
|Optional Background
Music Source
Model CTG-1 Clock ControlledTone Generator (DOD# 460)
To Input of OptionalPaging Amplifier
(not included)
PM
TIME/ CANCEL- + MODE
ALERT TONESSINGLE DOUBLE TRIPLE
VIKING ©
MODEL CTG-1
LOCK
SET DAYSET TIME
SET EVENTS
REVIEW/CANCEL
CLOCK CONTROLLEDTONE GENERATOR
VOL
9V BATTERYBACKUP
1 2 3 4 5 6 7 8 9 10 11 12
“The store will be closing in 10 minutes. Please bring items to the check out...”
In this application, the DVA-2WA is used in conjunction with a Viking CTG-1 Clock Controlled Tone
Generator (DOD 460) to provide time activated promotional voice messages over an existing paging
system.
**
* Note: Up to three 8-ohm speakers may be connected (not included). Viking models 25AE Paging Horn, 30AECeiling Speaker or equivalent are recommended. For more information, see DOD 498.
D. Single Line 7.5 Minute Digital Announcer
C
C
MADE IN
USA
TPG
1 432
ON
1 765
VIKING©
VIKINGELECTRONICS
HUDSON WI, 54016
DIGITAL ANNOUNCERWITH 2 WATT AMPLIFIER
POW
ER 1
2V D
C
MODEL DVA-2WA MASTERVOLUME
AUX. AUDIOVOLUME
MIN MAX MIN MAX
1 2 3 4 5 6
600
OH
M A
UD
IOO
UTP
UT
S PE A
KE R
OU
TPU
T
MES
SAG
E R
EPEA
TD
ELAY
TIM
ES
HA
ND
S ET
RE C
/ M
ON
I TO
R
RE C
OR
D A
UD
IOIN
PUT
(MIC
/ TA
P E)
AU
X . A
UD
IOIN
PUT
/ MO
H
3 4 1 2 5 6 7
MIC
ATT
ENU
ATIO
NA
UTO
REP
EAT
RE M
OTE
TR
I GG
E R
PRES
S A
ND
HO
LD
DEF
AU
LT M
ESSA
GE
STAT
US
- PW
R
STA
RT
/ STO
P
1 2 3
on
VIKING© MODEL RAD-1A
REMOTE ACCESSDEVICE
VIKINGELECTRONICS
HUDSON, WI 54016
DTM
F O
FF
600
OH
M A
UD
IO
PHO
NE
LIN
E O
UT
# #
ENA
BLE
LE
AR
N M
OD
E
PHONELINE
IN
PHONELINEOUT 2 31 4 5 6 7
REL
AY
CO
NTA
CTS
N.O
.
CO
M
N.C
.
ON
4 65
C.O. Line or Analog PABX/KSU Station
DIP Switches(see page 9)
Step 1 Connect as shown.
Step 2 Turn DIP switch 5 ON (see page 9).
Step 3 Program the RAD-1A as shown in the RAD-1A Product Manual, DOD 410.
In this application, the RAD-1A Remote Access Device will answer the line and trigger the message
on the DVA-2WA to play from the beginning.
Important: The RAD-1A “Call Timer” must be programmed to a time long enough for theDVA-2WA to play its entire message. Please refer to the RAD-1A Product Manual, DOD 410.
7
Recording
A. Recording from an Electret Microphone or Carbon Handset
Step 1.Set DIP switch 1 to the OFF position and remove any background music source from the AUX
AUDIO input.
Step 2.
Connect the 1/8” Electret microphone plug to the Record Audio input and set DIP switch 7 to the
OFF position or connect a carbon handset to the modular jack of the DVA-2WA and set DIP switch
7 to the ON position. See page 9.
Step 3.Slide the PLAY/RECORD switch to the right, the LED will light steady to indicate the DVA-2WA is in
the record mode. Note: To avoid feedback, turn the Master Volume control to “min” position.
Step 4.Momentarily press the START/STOP button to begin recording. The LED will flash fast to indicate
you are recording.
Step 5. Momentarily press the START/STOP button again to stop recording, the LED will light steady.
Step 6. Repeat steps 4 and 5 for each message you wish to record.
Step 7. Slide the PLAY/RECORD switch to the left to place the DVA-2WA back into the play mode.
Step 8.Turn up the Master Volume control and review recording(s) by momentarily pressing the
START/STOP button and listening to messages in handset, speakers or 600 ohm output.
C
C
MADE IN
USA
TPG
1 432
ON
1 765
VIKING©
VIKINGELECTRONICS
HUDSON WI, 54016
DIGITAL ANNOUNCERWITH 2 WATT AMPLIFIER
POW
ER 1
2V D
C
MODEL DVA-2WA MASTERVOLUME
AUX. AUDIOVOLUME
MIN MAX MIN MAX
1 2 3 4 5 6
600
OH
M A
UD
I OO
UTP
UT
SPEA
KER
OU
TPU
T
MES
SAG
E R
EPEA
TD
ELAY
TIM
ES
HA
ND
SET
REC
/ M
ON
ITO
R
REC
OR
D A
UD
I OIN
PUT
( MIC
/ TA
PE)
AU
X. A
UD
IOIN
PUT
/ MO
H
3 4 1 2 5 6 7
MIC
ATT
ENU
ATIO
NA
UTO
REP
EAT
REM
OTE
TR
I GG
ER
PRES
S A
ND
HO
LD
DEF
AU
LT M
ESSA
GE
STAT
US
- PW
R
STA
RT
/ STO
P
OFF
1
ON7
OFF
Carbon HandsetSet DIP switch 7 to ON
(Viking part # Q171030 orequivalent, not included)
Electret Microphone with 1/8” jackSet Dip switch 7 to OFF
(NRG Research Inc. Part # SA-125 (www.nrgresearch.com) or equivalent, not included)
DIP switch 7 ONfor CarbonHandset
DIP switch 7 OFFfor Electret Mic
12V DCAdapter
(included)
120V AC
Important: If you experience hum during the playback of user-recorded messages, earth ground Speaker Output terminal 5 before recording messages.
DIP Switches(see page 9)
DIP Switches(see page 9)
Start/Stop Button
Notes: If the total available record time is surpassed while recording, the status LED will pulse hi-low. To re-record all user-recorded messages, move the switch to play then back to the record position. This will allow youto record over all the previous messages in memory.
8
Step 1.Set DIP switch 1 to the OFF position and DIP switch 7 in the ON position and disconnect any
background music source from the AUX AUDIO input. See page 9.
Step 2. Set the volume on the MP3 player / Tape player / CD player / PC to the middle position.
Step 3.Connect the output from the MP3 player / Tape player / CD player / PC to the RECORD AUDIO input
jack of the DVA-2WA using the double ended 1/8” audio cord provided.
Step 4.Slide the Play/Rec switch to the right, the LED will light steady to indicate the DVA-2WA is in the
record mode.
Step 5.Momentarily press the START/STOP button to begin recording. The LED will flash fast to indicate
you are recording.
Step 6. Momentarily press the START/STOP button again to stop recording, the LED will light steady.
Step 7. Repeat steps 5 and 6 for each message you wish to record.
Step 8. Slide the PLAY/RECORD switch to the left to place the DVA-2WA back into the play mode.
C
C
MADE IN
USA
TPG
1 432
ON
1 765
VIKING©
VIKINGELECTRONICS
HUDSON WI, 54016
DIGITAL ANNOUNCERWITH 2 WATT AMPLIFIER
POW
ER 1
2V D
C
MODEL DVA-2WA MASTERVOLUME
AUX. AUDIOVOLUME
MIN MAX MIN MAX
1 2 3 4 5 6
600
OH
M A
UD
I OO
UTP
UT
SPEA
KER
OU
TPU
T
MES
SAG
E R
EPEA
TD
ELAY
TIM
ES
HA
ND
SET
REC
/ M
ON
ITO
R
REC
OR
D A
UD
I OIN
PUT
( MIC
/ TA
PE)
AU
X. A
UD
IOIN
PUT
/ MO
H
3 4 1 2 5 6 7
MIC
ATT
ENU
ATIO
NA
UTO
REP
EAT
REM
OTE
TR
I GG
ER
PRES
S A
ND
HO
LD
DEF
AU
LT M
ESSA
GE
STAT
US
- PW
R
STA
RT
/ STO
P
OR
Optional Handset for monitoring recordings
(Viking part # Q171030 or equivalent, not included)
MP3 Player(not included)
CD Player(not included)
OFF
1 ON
7
12V DCAdapter
(included)
120V AC
Important: If you experience hum during the playback of user-recorded messages, earth ground Speaker Output terminal 5 before recording messages.
DIP Switches(see page 9)
DIP Switches(see page 9)
Start/Stop Button
PC Sound Card(not included)
B. Recording from a Tape, CD Player or Any Line Level Source (PC sound card, etc)
Notes: If the total available record time is surpassed while recording, the status LED will pulse hi-low. To re-record all user-recorded messages, move the switch to play then back to the record position. This will allow youto record over all the previous messages in memory.
9
ON = Unit will only playback the professionally pre-recorded on-hold pacifier messages (4
messages, approximately 30 seconds of total playback time). See the table below for specifications.
Note: The 4 pre-recorded messages are stored in non-volatile memory and cannot be re-recordedor erased.
OFF = Unit will only playback the user-recorded message(s) (total number of messages limited to
250 or the maximum record time of 7.5 minutes).
A. DIP Switch 1: Pre-Recorded or User-Recorded Messages
B. DIP Switches 2 / 3 / 4: Delay Time
Between Message Playback
Message # Length Message
1 4.5 sec “Please continue to hold. We’ll be back with you as soon as possible.”
2 7.5 sec“Thank you for holding, we look forward to talking with you. Please continue tohold and we’ll be back with you in a moment.”
3 6.5 sec“Please continue to hold. Your call is very important to us. We’ll be back withyou in a moment.”
4 6.5 sec“Thank you for holding. We appreciate your patience. Please hold the line andwe’ll be right back with you.”
C
C
MADE IN
USA
TPG
1 432
ON
1 765
VIKING©
VIKINGELECTRONICS
HUDSON WI, 54016
DIGITAL ANNOUNCERWITH 2 WATT AMPLIFIER
POW
ER 1
2V D
C
MODEL DVA-2WA MASTERVOLUME
AUX. AUDIOVOLUME
MIN MAX MIN MAX
1 2 3 4 5 6
600
OH
M A
UD
I OO
UTP
UT
SPEA
KER
OU
TPU
T
MES
SAG
E R
EPEA
TD
ELAY
TIM
ES
HA
ND
SET
REC
/ M
ON
ITO
R
REC
OR
D A
UD
I OIN
PUT
( MIC
/ TA
PE)
AU
X. A
UD
IOIN
PUT
/ MO
H
3 4 1 2 5 6 7
MIC
ATT
ENU
ATIO
NA
UTO
REP
EAT
REM
OTE
TR
I GG
ER
PRES
S A
ND
HO
LD
DEF
AU
LT M
ESSA
GE
STAT
US
- PW
R
STA
RT
/ STO
P
ON
OFF1 432 765
Switch 2 Switch 3 Switch 4 Delay Time
OFF OFF OFF 2 seconds
OFF OFF ON 15 seconds
OFF ON OFF 30 seconds
OFF ON ON 60 seconds
ON OFF OFF 5 minutes
ON OFF ON 7.5 minutes
ON ON OFF 15 minutes
ON ON ON 30 minutes
Note: DIP Switches shownin factory default positions
ON = Message will only play while a contact is maintained across terminals 1 and 2.
OFF = Message will continue to play after contact is removed.
These DIP switches are used to select the
delay time for background music between
message playback. Use the table at the right
to select your desired delay time.
DIP Switch Programming
D. DIP Switch 6: Continuous/Normal Play Mode
C. DIP Switch 5: Remote Trigger Operation
E. DIP Switch 7: Input Gain Adjustment
ON = Continuous loop.
OFF = Normal play.
ON = Reduce gain for line level devices.
OFF = High gain for electret mics.
10
C. Continuous Loop (DIP Switch 6 ON)
In the continuous loop mode (see Installation section C), the DVA-2WA will play all
recorded messages one at a time in the order in which they were recorded with
programmed delay times between each message. Delays between message playback
are selectable from 2 seconds to 30 minute increments (see DIP Switch Programming
section B). If a background music source is connected, music will be faded in and out
during the delay times.
Note: If the Auxiliary Audio is not loud enough, and the AUX AUDIO is at maximum,increase the volume of your music source (licensed radio, etc.)
Operation
The DVA-2WA is designed to be recorded from any line level source (tape/CD player,
PC soundcard, etc.) or live from an Electret microphone or carbon handset. Single or
multiple messages may be recorded. You may record up to 250 messages, but the total
length of all messages may not exceed the maximum record time. With the
PLAY/RECORD switch in the RECORD (right) position follow the steps in the
Recording section on pages 7 and 8.
With the PLAY/RECORD switch in the PLAY position, the DVA-2WA is ready to play.
Momentarily press the start switch on the front panel or a remote switch connected to
the remote trigger terminals (or “REMOTE SW” pads 1 & 2) to initiate a single message
playback. Each message will playback one at a time in the order in which they were
recorded. After a message has been played, the button must be pressed again for the
next message. The START/ STOP switch on the front panel (or the switch connected
to “REMOTE SW” pads 1 & 2) can also be used to start and stop message playback.
Momentarily pressing the switch during an announcement will stop playback and will
also reset the unit to begin playback from the first message recorded on the next switch
activation or remote trigger.
A. Recording
B. Information On-Demand
Viking's model CTG-1 is a clock controlled tone generator
designed to provide accurately timed alert tones or
buzzer sounds over an existing paging system.
The CTG-1 can be programmed to output single, double
or triple alert tones or buzzer sounds with up to 128
events in a 24 hour period. These tone/buzzer sounds
are ideal for indicating the start and end of shifts, break
times, lunch periods, etc. for factories, schools, or any
business requiring an audible indication of specified
times. Each day of the week can be programmed to either on or off, allowing you to turn off the
alert tones during specific days of the week (weekends, etc.) The CTG-1 has three contact
closure inputs for triggering an emergency siren, evacuation signal or a door bell sound. See
DOD 460 for more information.11
Related Products
The 25AE, 30AE, 35AE, and 40AE
paging speakers provide additional
economical paging coverage to
existing Viking paging units (PA-2A,
PA-15, PA-30, PA-60, HF-3W, M2W)
or to any system with an 8 ohm output.
In outdoor, factory or warehouse
environments, 25AE paging horns are
the best method of producing
understandable sound. In these environments the directional design allows the installer to
focus the sound cone down aisles and toward work areas.
In office and restaurant environments, it is best to distribute sound more evenly. Ceiling
mounted 30AE, 35AE, or 40AE speakers in close proximity offer the best distribution and are
cost effective. The 35AE speakers include a volume control.
The RAD-1A Remote Access Device gives
authorized users remote access to PABX, Centrex
and Electronic Key system features. It can also
provide bridging to a second central office line. With
two levels of access and programmable toll
restriction, the RAD-1A provides the security required
to help prevent phone system and toll abuse.
The RAD-1A answers on the first ring and
disconnects on CPC, call time out, silence time out,
return dial tone or by dialing #7. Separate 600 ohm
audio and telephone line outputs are provided, allowing connection to audio amplifiers, digital
announcers, telephone lines or analog PABX extensions. For “line extender” applications, the
user does not have to hang up and redial the RAD-1A to make another call. The RAD-1A will
also provide a hookswitch flash on the telephone line out ports to access PABX, Centrex or
Electronic Key system features.
Add Time Controlled Alert Tones and Emergency Tones to Your Paging System
Line Powered Remote Access Device
Cost Effective Speakers for Indoor and Outdoor Use
For more info,
see DOD 498
For more info, see DOD 410
12
IF YOU HAVE A PROBLEM WITH A VIKING PRODUCT, CONTACT: VIKING TECHNICAL SUPPORT AT (715) 386-8666Our Technical Support Department is available for assistance Monday through Friday 8am - 5pm central time. So that we can give you betterservice, before you call please:1. Know the model number, the serial number and what software version you have (see serial label).2. Have your Product manual in front of you.3. It is best if you are on site.
RETURNING PRODUCT FOR REPAIRThe following procedure is for equipment that needs repair:1. Customer must contact Viking's Technical Support Department at 715-386-8666 to obtain a Return Authorization (RA) number. Thecustomer MUST have a complete description of the problem, with all pertinent information regarding the defect, such as options set,conditions, symptoms, methods to duplicate problem, frequency of failure, etc.2. Packing: Return equipment in original box or in proper packing so that damage will not occur while in transit. Static sensitive equipmentsuch as a circuit board should be in an anti-static bag, sandwiched between foam and individually boxed. All equipment should be wrappedto avoid packing material lodging in or sticking to the equipment. Include ALL parts of the equipment. C.O.D. or freight collect shipmentscannot be accepted. Ship cartons prepaid to: Viking Electronics, 1531 Industrial Street, Hudson, WI 540163. Return shipping address: Be sure to include your return shipping address inside the box. We cannot ship to a PO Box.4. RA number on carton: In large printing, write the R.A. number on the outside of each carton being returned.
RETURNING PRODUCT FOR EXCHANGEThe following procedure is for equipment that has failed out-of-box (within 10 days of purchase):1. Customer must contact Viking’s Technical Support at 715-386-8666 to determine possible causes for the problem. The customer MUSTbe able to step through recommended tests for diagnosis.2. If the Technical Support Product Specialist determines that the equipment is defective based on the customer's input and troubleshooting,a Return Authorization (R.A.) number will be issued. This number is valid for fourteen (14) calendar days from the date of issue.3. After obtaining the R.A. number, return the approved equipment to your distributor, referencing the R.A. number. Your distributor will thenreplace the Viking product using the same R.A. number.4. The distributor will NOT exchange this product without first obtaining the R.A. number from you. If you haven't followed thesteps listed in 1, 2 and 3, be aware that you will have to pay a restocking charge.
Warranty
TWO YEAR LIMITED WARRANTYViking warrants its products to be free from defects in the workmanship or materials, under normal use and service, for
a period of two years from the date of purchase from any authorized Viking distributor. If at any time during the warrantyperiod, the product is deemed defective or malfunctions, return the product to Viking Electronics, Inc., 1531 Industrial Street,Hudson, WI., 54016. Customer must contact Viking's Technical Support Department at 715-386-8666 to obtain a ReturnAuthorization (R.A.) number.
This warranty does not cover any damage to the product due to lightning, over voltage, under voltage, accident, misuse,abuse, negligence or any damage caused by use of the product by the purchaser or others. This warranty does not covernon-EWP products that have been exposed to wet or corrosive environments. This warranty does not cover stainless steelsurfaces that have not been properly maintained.
NO OTHER WARRANTIES. VIKING MAKES NO WARRANTIES RELATING TO ITS PRODUCTS OTHER THAN ASDESCRIBED ABOVE AND DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTIES OR MERCHANTABILITY ORFITNESS FOR ANY PARTICULAR PURPOSE.
EXCLUSION OF CONSEQUENTIAL DAMAGES. VIKING SHALL NOT, UNDER ANY CIRCUMSTANCES, BE LIABLETO PURCHASER, OR ANY OTHER PARTY, FOR CONSEQUENTIAL, INCIDENTAL, SPECIAL OR EXEMPLARYDAMAGES ARISING OUT OF OR RELATED TO THE SALE OR USE OF THE PRODUCT SOLD HEREUNDER.
EXCLUSIVE REMEDY AND LIMITATION OF LIABILITY. WHETHER IN AN ACTION BASED ON CONTRACT, TORT(INCLUDING NEGLIGENCE OR STRICT LIABILITY) OR ANY OTHER LEGAL THEORY, ANY LIABILITY OF VIKING SHALLBE LIMITED TO REPAIR OR REPLACEMENT OF THE PRODUCT, OR AT VIKING'S OPTION, REFUND OF THEPURCHASE PRICE AS THE EXCLUSIVE REMEDY AND ANY LIABILITY OF VIKING SHALL BE SO LIMITED.
IT IS EXPRESSLY UNDERSTOOD AND AGREED THAT EACH AND EVERY PROVISION OF THIS AGREEMENTWHICH PROVIDES FOR DISCLAIMER OF WARRANTIES, EXCLUSION OF CONSEQUENTIAL DAMAGES, ANDEXCLUSIVE REMEDY AND LIMITATION OF LIABILITY, ARE SEVERABLE FROM ANY OTHER PROVISION AND EACHPROVISION IS A SEPARABLE AND INDEPENDENT ELEMENT OF RISK ALLOCATION AND IS INTENDED TO BEENFORCED AS SUCH.
Due to the dynamic nature of the product design, the information contained in this document is subject to changewithout notice. Viking Electronics, and its affiliates and/or subsidiaries assume no responsibility for errors andomissions contained in this information. Revisions of this document or new editions of it may be issued to incorporatesuch changes.
Printed in the U.S.A.DOD 110 ZF301530 Rev C