VACUUM TOILET · NOTE: Evac 910 vacuum toilets with the Mosaik, Aniara or Open front seats and...

EVAC reserves the right to make alterations to this specification without prior notice.© Copyright Evac Oy. All rights reserved. 1

EVACCommercial Marine Equipment

VVVVVAAAAACUUM CUUM CUUM CUUM CUUM TTTTTOILETOILETOILETOILETOILET

TECHNICAL DATADate: Doc.17 Sep 2009 001991-1

6543418 EVAC 910, WALL MODEL, PRESTIGE SILENT, WHITE6543419 EVAC 910, WALL MODEL, MOSAIK, WHITE

* Prestige seat and cover fulfill ANSI Z124.5 - 1997 [Plastic Toilet ( Water closet ) Seats] requirements.

** See available colours in document 002003-2

Materials Bowl: White vitreous china**Seat; *Prestige: UF-S**, Mosaik: PP**Cover; *Prestige: UF-S **, Mosaik: PP**Pneumatic push button: White plastic, ABSDischarge valve; plastic parts: PP, rubber parts: NR

Operating data Water pressure: 3 - 10 barOperating vacuum: -0.3 ... - 0.6 barWater consumption: ~1.2 ±0.15 litres/flush ( water pressure: 4 bar, vacuum: -0.4 bar )Air consumption: ~60 ±10 litres/flush (normal atmospheric air)

Connections Water supply: 1/2" MPT, flexible hoseDischarge: Discharge connection Ø50, connection sleeve includes two hose clampsto O.D. 48 - 52mm pipes

Shipping data P/N 6543418 Evac 910, wall model, Prestige Silent:Net weight: 20.8 kgShipping weight: 23.1 kgShipping volume: 0.168m3

P/N 6543419 Evac 910, wall model, Mosaik:Net weight: 17.7 kgShipping weight: 19.7 kg

Water supply 1/2”

Shut-off valve

Vacuum breaker

P/N 6541458 Pneumatic push button, whiteMax. 420

230

550

Max

. 450

110

365

5043

0

Seat and cover:Prestige* or Mosaik

Bowl

Connection sleeve

Discharge connection

250

400

Flexible waterconnection hose

45

Edge strip

Ø50




TECHNICAL DATADate: Doc. 17 Sep 2009 001996-2

6543420 EVAC 910, WALL MODEL USPH, PRESTIGE SILENT, WHITE6543421 EVAC 910, WALL MODEL USPH, MOSAIK, WHITE6544766 EVAC 910, WALL MODEL USPH, OPEN FRONT, WHITE

Materials Bowl: White vitreous china**Seat; *Prestige: UF-S**, Mosaik: PP**, Open front: UF-S**Cover; *Prestige: UF-S**, Mosaik: PP**, Open front: UF-S**Pneumatic push button: White plastic, ABSDischarge valve; plastic parts: PP, rubber parts: NR

Operating data Water pressure: 3 - 10 barOperating vacuum: -0.3 ... - 0.6 barWater consumption: ~1.2 ±0.15 litres/flush ( water pressure: 4 bar, vacuum: -0.4 bar )Air consumption: ~ 60 ±10 litres/flush (normal atmospheric air)

Connections Water supply with USPH: 1/2" MPT, flexible hoseDischarge: Discharge connection Ø50, connection sleeve includes two hose clampsto O.D. 48 - 52mm pipes

Shipping data P/N 6543420 EVAC 910, wall model USPH, Prestige Silent:Net weight: 21.6 ±0.5kgShipping weight: 25.1 ±0.5kgShipping volume: 0.168m3

P/N 6543421 EVAC 910, wall model USPH, Mosaik:Net weight: 18.6 ±0.5kgShipping weight: 20.6 ±0.5kgShipping volume: 0.168m3

P/N 6544766 EVAC 910, wall model USPH, Open front:Net weight: 20.4 ±0.5kgShipping weight: 22.9 ±0.5kgShipping volume: 0.168m3

* Prestige seat and cover fulfill ANSI Z124.5 - 1997 [Plastic Toilet ( Water closet ) Seats] requirements.** See available colours on document 002003-2.

P/N 6541458 Pneumatic push button, whiteMax. 420

230

550

Max

. 450

110

365

5043

0

Water supply 1/2”

Shut-off valve

Edge strip

Seat and cover:Prestige*, Mosaik or Open front

Bowl

Connection sleeve

Dischargeconnection

250

400


45

USPH vacuum breaker

Ø50




TECHNICAL DATADate: Doc.

Materials Bowl: White vitreous china *Seat; Silent: PP*, Aniara: PP*Cover; Silent: PP*, Aniara: PP*Pneumatic push button: PlasticDischarge valve: Plastic parts: PP, rubber parts: NR

Operating data Water pressure: 3 ...10 barOperating vacuum: -0.3 ... -0.5 barWater consumption: ~1.2 ±0.15 litres/flush ( water pressure: 4 bar, vacuum: -0.4 bar )Air consumption: ~ 60 ±10 litres/flush (normal atmospheric air)

Connections Water supply: 1/2" MPT, flexible hoseDischarge: Rubber elbow 90°, two hose clamps are included in the rubber elbow 90° to O.D.48 - 52mm pipe.

Shipping data P/N 6545825 EVAC 910, floor model, Silent:Net weight: 22.6 ±0.5kgShipping weight: 24.6 ±0.5kgShipping volume: 0.168m3

P/N 6545826 EVAC 910, floor model, Aniara:Net weight: 20.7 ± 0.5kgShipping weight: 19.4 ±0.5kgShipping volume: 0.168m3

18 May 2009 002245-1

6545825 EVAC 910, FLOOR MODEL, SILENT (EVACINHUSH), WHITE6545826 EVAC 910, FLOOR MODEL, ANIARA, WHITE

* See available colours indocument 002003-2

150

560

Max

. 465

Max. 390

195 90 150

Dischargeconnection Ø50

Rubberelbow 90°

Water supply 1/2"

Shut-off valve

Vacuum breakerSeat and cover,Silent or Aniara

Bowl


Ø10

P/N 6544996 Pneumatic push buttonP/N 6541057 Optional pneumatic push button kit,wall installation, push button: white plastic

Ø50




TECHNICAL DATADate: Doc. 002246-118 May 2009

6545827 EVAC 910, FLOOR MODEL USPH, SILENT (EVACINHUSH), WHITE6545828 EVAC 910, FLOOR MODEL USPH, ANIARA, WHITE6545829 EVAC 910, FLOOR MODEL USPH, OPEN FRONT, WHITE

Materials Bowl: White vitreous china*Seat; Silent: PP*, Aniara: PP*, Open front: UF-S*Cover; Silent: PP*, Aniara: PP*, Open front: UF-S*Pneumatic push button: PlasticDischarge valve: Plastic parts: PP, rubber parts: NR

Operating data Water pressure: 3 ... 10 barOperating vacuum: -0.3 ... -0.50 barWater consumption: 1.2 ±0.15 litres/flush ( water pressure: 4 bar, vacuum: -0.4 bar )Air consumption: 60 ±10 litres/flush (normal atmospheric air)

Connections Water supply: 1/2" MPT, flexible hoseDischarge: Rubber elbow 90°, two hose clamps are included in the rubber elbow 90° toO.D. 48-52mm pipe.

Shipping data P/N 6545827 EVAC 910, floor model USPH, Silent:Net weight: 23.6 ±0.5kgShipping weight: 25.6 ±0.5kgShipping volume: 0.168m³

P/N 6545828 EVAC 910, floor model USPH, Aniara:Net weight: 21.7 ±0.5kgShipping weight: 23.7 ±0.5kgShipping volume: 0.168m³

P/N 6545829 EVAC 910, floor model USPH, Open front:Net weight: 23.6 ±0.5kgShipping weight: 25.6 ±0.5kgShipping volume: 0.168m³

* See available colours ondocument 002003-2

P/N 6544996 Pneumatic push buttonP/N 6541057 Optional pneumatic push button kit,wall installation, push button: white plastic

150

560

Max

. 465

Max. 390

195 90 150

DischargeconnectionRubberelbow 90°

Seat and cover,Silent, Aniara or Open front

Bowl


Vacuum breakerUSPH

Water supply 1/2"

Cu-pipeØ12

Ø10 Ø50

Shut-off valve




TECHNICAL DATADate: Doc.12 May 2008 1:01005F

6541458 PNEUMATIC PUSH BUTTON, WHITE

Materials Cover: ABS, whiteButton: PBT, whiteBottom plate: POM, natural

Connections Hose nipple Ø4

Shipping data Net weight: 0.2kg

4058

170

60Ø 4.5




TECHNICAL DATADate: Doc. 18 May 2009 002247-1

6544996 PNEUMATIC PUSH BUTTON

Pneumatic push button

Materials Push button: Plastic

Connections Hose nipple Ø4/Ø2





TECHNICAL DATADate: Doc. 31 Aug 2009 1:01197E

6541057 OPTIONAL PNEUMATIC PUSH BUTTON KIT

Materials Pneumatic push button, cover and button: White plasticCover plate: Nickel-plated brassProtecting pipe: White color PVC

Connections Hose nipple Ø4/Ø2



Cover plate

Protecting pipe

Installation kit

Pneumatic pushbutton

Ø10

900Cover plate

Protecting pipe




TECHNICAL DATADate: Doc.06 Jul 2009 002003-5

STANDARD COLOURS, EVAC 910, WALL MODELS AND FLOOR MODELS

Bowl, seat and cover are available in white and in standard colours. Standard colours are shown in the standardcolour palette.

! NOTE: Evac 910 vacuum toilets with the Mosaik, Aniara or Open front seats and covers are available only inwhite colour.

When you order a toilet in standard colour you must give the toilet's part number, the name and the standardcolour code. Example: 6544794 Wall model USPH, Prestige Silent, 30 Light green.

You can order the Prestige and the Silent seats and covers in additional colours only in large series. When youorder seat and cover in additional colours you must give an international colour code like the Muncell or RAL.

01 White 10 Light grey 68 Pergamon,light beige

30 Light green

Standard colour palette

*

COLOURS FOR WALL MODEL TOILETS Toilet bowl Seat and cover

Product no. Toilet name Standard colour code Standard colour code Additional colours* min. 250 pcs/order min.1000 pcs/order min.1000 pcs/order

6543418 Wall model, Prestige Silent 01 white 01 white X6543419 Wall model, Mosaik 01 white 01 white6543420 Wall model, USPH, Prestige Silent 01 white 01 white X6543421 Wall model, USPH, Mosaik 01 white 01 white6544766 Wall model, USPH, Open front 01 white 01 white6544791 Wall model, USPH, Prestige Silent, autoflush 01 white 01 white X

10 Light grey 10 Light grey6544792 Wall model, USPH, Prestige Silent, autoflush 30 Light green 30 Light green X

68 Pergamon, light beige 68 Pergamon, light beige 10 Light grey 10 Light grey

6544793 Wall model, Prestige Silent 30 Light green 30 Light green X 68 Pergamon, light beige 68 Pergamon, light beige 10 Light grey 10 Light grey

6544794 Wall model, USPH, Prestige Silent 30 Light green 30 Light green X 68 Pergamon, light beige 68 Pergamon, light beige

6545030 Wall model, B15, Prestige Silent 01 white 01 white X6545031 Wall model, USPH, B15, Prestige Silent 01 white 01 white X6545818 Wall model, USPH, Prestige Silent, autoflush 01 white 01 white X

10 Light grey 10 Light grey6546081 Wall model, USPH, Prestige Silent, autoflush 30 Light green 30 Light green X

68 Pergamon, light beige 68 Pergamon, light beige

COLOURS FOR FLOOR MODEL TOILETS Toilet bowl Seat and cover

Product no. Toilet name Standard colour code Standard colour code Additional colours* min. 250 pcs/order min.1000 pcs/order min.1000 pcs/order

6543422 Floor model, Silent 01 white 01 white X6543423 Floor model, Aniara 01 white 01 white6543424 Floor model, USPH, Silent 01 white 01 white X6543425 Floor model, USPH, Aniara 01 white 01 white6544797 Floor model, USPH, Open front 01 white 01 white6545825 Floor model, Silent 01 white 01 white X6545826 Floor model, Aniara 01 white 01 white6545827 Floor model, USPH, Silent 01 white 01 white X6545828 Floor model, USPH, Aniara 01 white 01 white6545829 Floor model, USPH, Open front 01 white 01 white




INSTALLATIONDate: Doc.12 Jan 2009 001998-3

6543418 EVAC 910, WALL MODEL, PRESTIGE SILENT6543419 EVAC 910, WALL MODEL, MOSAIK

220

330

140

160

220

*(W

ater

supp

ly ho

se)

! NOTE: Recommended place for the button.If place is changed, consult EVAC.

A

A

U-beam(Not included in EVAC supply)Fasten the beam to a solid structure.

130

P/N 5433572Straight connection hose


50

Seat and cover:Prestige or Mosaik

110

45Ø

50

Shut-off valve1/2" MPT

Flexible water hose

Vacuum breaker

Discharge pipealignment toleranceto be ±3.0 mm

P/N 6544769Rubber elbow 90°, optional connection

* The vacuum breaker air inlet must be located at a minimum of150mm (6") above the overflow point of the toilet.

*150

! NOTE: Overflow point is inside the toilet bowl

Overflow point

Vacuum breaker installation,see doc. 002017-1






Installation kit 6540972 consists of:

Plastic nut M12 2 pcsGuiding nut 2 pcsEdge strip 1 pcMounting instruction 1 pcStraight connection hose 1 pcHose clamp 2 pcs

Toilet supporting beams for wall models

Cross section A - AEdge strip

Total length of bolt = T + 65 ± 2T 65±2

Beam Toilet bowl

Bolt M12 (not EVAC supply) to be welded.! NOTE: Thread on the bolt must be full length.

Ø13

230

Dimensions of toilet service opening through the wall

370

210200

90

R20

Bolt M12 to be welded(not EVAC supply)

Length according tothe space available

230

220

380

200

U-beam 50x30x2 (not EVAC supply)




INSTALLATIONDate: Doc.12 May 2008 002017-1


• Connect the water connection hose A to the water valve.• Install the back plate assembly on the wall using the bowl fastening bolts B (M12, not included) and the guiding

nuts C (M12). The guiding nuts are necessary.• Connect the hose D from the flushing ring to the water valve. Do not use any kind of grease during

installation! Secure with hose clamps. Tighten the hose clamps with pliers.

! NOTE: Install the hose D from the flushing ring in the toilet bowl to the right side of the discharge valve and belowall other hoses.

• Lift bowl onto the fastening bolts and tighten the securing nuts E. Tightening torque is 15-20 Nm.

! NOTE: Check hoses through the toilet service opening in the wall that the hoses run smoothly. The hoses shallnot have any kinks.

• Fit the edge strip as shown in figure 1. Place the joint of the strip to the bottom side of the bowl.• Install a seat and a cover. Look at The Prestige’s hinges installation in the picture above.• Connect the discharge connection. Secure with the hose clamps.• Connect the shut-off valve/vacuum breaker assembly to the water supply. The shut-off valve must be installed to

the water supply piping's side to ensure the correct flow direction in the vacuum breaker. Note that the vacuumbreaker must be installed vertically as shown.

• Connect the water connection hose A to the shut-off valve/vacuum breaker assembly.• Install the pneumatic push button (See document 002002-1).

E

A, hose (EPDM) L=400,braid of stainless steel wire

DWater valve

B


Edge strip

Mosaik

Prestige

Fig.1

C

Vacuum breaker

Shut-off valve,1/2” MPT BSP

Shut-off valve /vacuum breakerassembly

Discharge valve(See notes!)

Hinge

Washer

Nut

Hingebody

or

Prestige’s hingesinstallation

Correct hinge installation

Fresh water connection

Back plateassembly

Pipe Ø12





6543420 EVAC 910, WALL MODEL USPH, PRESTIGE SILENT6543421 EVAC 910, WALL MODEL USPH, MOSAIK6544766 EVAC 910, WALL MODEL USPH, OPEN FRONT

Overflow point

* The vacuum breaker air inlet must be located at a minimum of150mm (6") above the overflow point of the toilet.

*150

70

! NOTE: Overflow point is inside the toilet bowl

220 14

016

022

0(W

ater

supp

ly ho

se)

A

A

U-beam(Not included in EVAC supply)Fasten the beam to a solid structure.

130

P/N 5433572Straight connection hose


50

Seat and cover:Prestige, Mosaik orOpen front

110

45

Shut-off valve1/2" MPT

Flexible water hose

USPH Vacuum breaker

Discharge pipealignment toleranceto be ±3.0 mm

P/N 6544769Rubber elbow 90°, optional connection

*(U

SPH

wal

l bra

cket

)Se

e al

so d

oc.

0020

01-1

90M

in. 2

80

330

! NOTE: Recommended place for the button.If place is changed, consult EVAC. Vacuum breaker installation,

see doc. 002001-1

Ø50






Installation kit 6540972 consists of:

Plastic nut 2 pcsGuiding nut 2 pcsEdge strip 1 pcMounting instruction 1 pcStraight connection hose 1 pcHose clamp 2 pcs

Toilet supporting beams for wall models

Cross section A - AEdge strip

Total length of bolt = T + 65 ± 2T 65±2

Beam Toilet bowl

Bolt M12 (not EVAC supply) to be welded.! NOTE: Thread on the bolt must be full length.

Bolt M12 to be welded(not EVAC supply)

Length according tothe space available

230

220

380

200

U-beam 50x30x2 (not EVAC supply)

Ø13

230

Dimensions of toilet service opening through the wall

370

210200

90

R20




INSTALLATIONDate: Doc.


18 Feb 2008 002001-1

• Connect the water connection hose A to the water valve.• Install the backplate assembly on the wall using the bowl fastening bolts B (M12, not included) and the guiding

nuts C (M12). The guiding nuts are necessary.• Connect the hose D from the flushing ring to the connecting nipple on the backplate (see drawing: Water

supply). Do not use any kind of grease during installation! Secure with hose clamps. Tighten the hoseclamps with pliers.

! NOTE: Install the hose D to the right side of the discharge valve and below the hose F.

• Lift bowl onto the fastening bolts and tighten the securing nuts E. Tightening torque is 15-20 Nm.

! NOTE: Check hoses through the toilet service opening in the wall that the hoses run smoothly. The hoses shallnot have any kinks.

Nut E

A

D

Water valve

B


or

Edge strip

Mosaik

Prestige

Fig.1

C

Shut-off valve

F

Discharge valve(See notes!)

Hingebody

Hinge

Washer

USPH vacuum breaker(see drawing: Water supply)

Open front

or

Back plateassembly






18 Feb 2008 002001-1

• Fit the edge strip as shown in the figure 1. Place the joint of the strip to the bottom side of the bowl.• Install a seat and a cover. See drawing: The Prestige’s hinges installation.• Connect the USPH vacuum breaker to the back plate's connecting nipples (see drawing: Water supply).• Fix the USPH vacuum breaker on the wall (see drawing: Water supply and see dimensions

from document 002000-2).• Connect the discharge connection. Secure with the hose clamps.• Connect the shut-off valve to the water supply. The shut-off valve must be installed to the water supply piping's

side to ensure the correct flow direction in the vacuum breaker. Note that the vacuum breaker must be installedvertically as shown.

• Connect the water connection hose A to the shut-off valve.• Install the pneumatic push button (see document 002002-1).

Prestige’s hinges installation

Correct hinge installation

Water supply

Back plate assembly

Hose (EPDM), L=500

Hose (EPDM), L=810

Vacuumbreaker

Hose to the flushing ringin the toilet bowl

Water valve

Fresh waterconnection

Pipe Ø12

Shut-off valve,1/2” MPT BSP

Hose (EPDM) L=400Braid of steinless steel wire

! NOTE: For non-U.S. flag vessels





6545825 EVAC 910, FLOOR MODEL, SILENT (EVACINHUSH)6545826 EVAC 910, FLOOR MODEL, ANIARA

Optional discharge connection

Discharge pipe alignment toleranceto be ± 3.0mm.

P/N 5433572Straight connection

150

20

Min.120

* The vacuum breaker air inlet must be installed min.150mm (6”) above the overflow point of the toilet.

Overflowpoint

Ø 48-52

390

465

225

360°

Min

. 150

*35

0

195 90

120

380

560

Max.100

Min.120

Flexible water connection hose

Shut-off valve

Vacuum breaker Pneumatic push button

P/N 5610010Cover support(not included)

Discharge pipealignment toleranceto be ± 3.0mm

Water supply1/2" MPT

150 51

0 ±1

0

186






Fixing to the floor with a fixing plate and wood screws

52 ±

2Welded bolt M8(not included)

Installation kit P/N 5824900 consists of:

Wood screw 5x45 2 pcsRubber elbow 1 pcHose clamp 2 pcsPlastic washer 2 pcsNut M8 2 pcsMounting instruction 1 pc

20

P/N 5779920 Fixing plate, plastic(not included)

Max

. 10

Section A

Section B

180

190

~ 15

A A

Optional fixing points

150

195


170 B B

Fixing to the floor with welded bolts





6545827 EVAC 910, FLOOR MODEL USPH, SILENT (EVACINHUSH)6545828 EVAC 910, FLOOR MODEL USPH, ANIARA6545829 EVAC 910, FLOOR MODEL USPH, OPEN FRONT

Discharge pipe alignment toleranceto be ± 3.0mm. P/N 5433572

Straight connection

150

20

Min.120

350

Min

. 150

*

195

Ø 48-52

90

120

380

390

465

360°

560

Max.100Min.120

Flexible water connection hoseShut-off valve

Vacuum breakerUSPH


P/N 5610010Cover support(not included)

Discharge pipealignment toleranceto be ± 3.0mm

Water supply 1/2" MPT

150

Optional discharge connection

510

±10

*The vacuum breaker air inlet must be installed min.150mm (6”) above the overflow point of the toilet.

Overflowpoint

225

186






Fixing to the floor with a fixing plate and wood screws

Installation kit P/N 5824900 consists of:

Wood screw 5x45 2 pcsRubber elbow 1 pcHose clamp 2 pcsPlastic washer 2 pcsNut M8 2 pcsMounting instruction 1 pc

20

P/N 5779920 Fixing plate, plastic(not included)

Max

. 10

Section A

180

190

~ 15

A A


52 ±

2Welded bolt M8(not included)

Section B

150

195


170 B B

Fixing to the floor with welded bolts





6545825 EVAC 910, FLOOR MODEL, SILENT (EVACINHUSH)6545826 EVAC 910, FLOOR MODEL, ANIARA6545827 EVAC 910, FLOOR MODEL USPH, SILENT (EVACINHUSH)6545828 EVAC 910, FLOOR MODEL USPH, ANIARA6545829 EVAC 910, FLOOR MODEL USPH, OPEN FRONT

13 May 2009 002250-1

• Connect the water connection hose A to the water valve B.• Connect the pipes from the USPH vacuum breaker to the connecting nipples of the backplate. Note the correct

flow direction (see water supply in the USPH models in the next page).• If you have an optional wall push button follow the installation instructions on the document 002002-1.• Lift the toilet bowl on it´s place, fix it on a floor using the screws/nuts and the washers. Use silicone compound

to seal joining between the bowl and the floor.• Connect the discharge connection. Secure with hose clamps.• Fix the USPH vacuum breaker on the wall (only in the USPH models).• Connect the shut-off valve/vacuum breaker assembly (the vacuum breaker assembly is not included in the USPH

models) to the water supply. The shut-off valve must be installed to the water supply piping's side to ensure thecorrect flow direction in the vacuum breaker. Note that the vacuum breaker must be installed vertically as shown.

• Connect the water connection hose A to the shut-off valve/vacuum breaker.• Install the seat and the cover.

A

Shut-off valve

B

Silent

Aniara

Vacuum breakerassembly(not in USPH models)

or

USPH vacuum breaker(only in USPH models)or

or

Open front

Hingebody

WasherHinge

Discharge connection pipe

Hose clamps

Water supply






13 May 2009 002250-1

Shut-off valve 1/2” MPT BSP

Fresh water connection pipe, Ø12USPH vacuum breaker

Hose to flushing ring in bowl

Water valve

Hose (EPDM), L=400,braid of stainless steel wire

Connection nipple(from the USPH vacuum breaker)

Connection nipples(to the USPH vacuumbreaker)

Pipe Ø12 Cu(chromium plated)

Water supply in the USPH models




INSTALLATIONDate: Doc.15 Feb 2008 002002-1

6541458 PNEUMATIC PUSH BUTTON, EVAC 910, WALL MODELS6541057 OPTIONAL PNEUMATIC PUSH BUTTON KIT, EVAC 910, FLOOR MODELS

Installing the push button on the wall, floor models withthe optional push button kit.(Hose and protecting pipe on the surface of the wall)

Control mechanism

1. Drill Ø6 mm hole for the hose A.2. Connect the plastic hose A from the control mechanism to

the bellow B. Warm the end of the hose if needed to helpinstallation.

3. Install the body C of push button on the wall using screws D(not included).

4. Snap the cover E of the push button bellow in its place.

! NOTE: Secure, that the hose A is not flattened afterinstallation. Air impulse must always flow free.

1. Thread the hose from the control mechanism through theprotection pipe A.

2. Install the protection pipe A on the wall using screws andclamps B.

3. Cut off the film of the bushing for the plastic hose in thebottom side of the push buttons cover.

4. Connect plastic hose from the control mechanism to thebellow C. Snap the plastic hose on the clip behind thebottom plate.

5. Install the push button body D to the wall using screws (notincluded).

6. Snap the cover of the push button bellow E in its place.

E

Ø 6

A D

3.

C

From the controlmechanism

60

60

AB

C

D

E

B

From the controlmechanism

Make sure, that the plastic hose does not get loose from thecontrol mechanism.

Plastic hose to thepush button

Controlmechanism




INSTALLATIONDate: Doc.15 Feb 2008 002002-1

6541458 PNEUMATIC PUSH BUTTON, EVAC 910, WALL MODELS6541057 OPTIONAL PNEUMATIC PUSH BUTTON KIT, EVAC 910, FLOOR MODELS

Install the protecting pipe under the discharge pipe.

Recommended place for the button

! NOTE: Make sure, that cover does not hit the push buttonwhen opened. (*In Aniara/Mosaik models dimension is 100mmsmaller due to the flexible cover.) If the place is changed,consult EVAC.

Control mechanism

~290

330*

130~6

40*

110

Optional push button(Floor models)

Floor models

Optional pneumatic push button kit

Discharge pipe




OPERATION AND MAINTENANCEDate: Doc.04 Jun 2008 002029-2

6543418 EVAC 910, WALL MODEL, PRESTIGE SILENT, WHITE6543419 EVAC 910, WALL MODEL, MOSAIK, WHITE6543420 EVAC 910, WALL MODEL USPH, PRESTIGE SILENT, WHITE6543421 EVAC 910, WALL MODEL USPH, MOSAIK, WHITE6544766 EVAC 910, WALL MODEL USPH, OPEN FRONT, WHITE

Start-up• Clean the bottom of the toilet bowl.• Check that the mini-check valve and the discharge valve are clean and working correctly.• Check that the water supply hose and the filter of the water valve are not blocked up.• Check that sufficient vacuum (-0.3 bar) is available.• Open the water supply valve in the water supply piping.• Press the toilet push button. Pressing the button starts the flushing sequence. The discharge valve opens and

the contents of the bowl are extracted by vacuum. At the same time the bowl is rinsed by water.• When the discharge valve has been closed water level is restored in the bowl by the closing time delay of the

water valve.

Monitoring the vacuum toilet in the normal operation• Check that the water valve provides the rinse water to the bowl at the same time as the discharge valve extracts

the bowl contents when the push button is pressed.• Check that the push button returns to it´s non-activated state.• Check that after the discharge valve closes, the water valve continues to provide water to the bowl. If the water

valve time delay is correctly adjusted, there should be a pool of water at the bottom of the bowl.• Check that there are no water or air leaks.

! NOTE: Water consumption is dependent on the water supply pressure and the vacuum level.

Preparation for a toilet not to be used for a long period• Close the water supply valve.• Run a flush cycle by pressing the push button.• Close the toilet seat cover.

Water valve

Flushing ring

Discharge valve

Push button on the wall(wall model toilets)

Controlmechanism

Mini-checkvalve

Direction A

Seat cover

Filter of thewater valve

Water supply piping

Water supply valveA




OPERATION AND MAINTENANCEDate: Doc.04 Jun 2008 002028-2

6543418 EVAC 910, WALL MODEL, PRESTIGE SILENT, WHITE6543419 EVAC 910, WALL MODEL, MOSAIK, WHITE6543420 EVAC 910, WALL MODEL USPH, PRESTIGE SILENT, WHITE6543421 EVAC 910, WALL MODEL USPH, MOSAIK, WHITE6544766 EVAC 910, WALL MODEL USPH, OPEN FRONT, WHITE

Operation

The toilet is flushed by pressing the push button. The pneumatic push button is connected to the control mechanismwith a control hose, which transports the air pulse from the push button to the control mechanism. The air pulse startsthe flushing sequence and the control mechanism connects vacuum to the control connections of the water valve andthe discharge valve. The water valve opens and lets rinsing water flow into the bowl through the flushing ring. After ashort delay vacuum acts in discharge valve housing and forces the rubber diaphragm in discharge valve to open.Contents of the bowl is drained to the vacuum sewer by a pressure difference between the bowl and vacuum sewer.The flushing cycle in the control mechanism starts the closing cycle. Vacuum enters to the relief valve. The relief valveopens the port between athmospheric air and the discharge valve. Athmospheric air enters to the discharge valve witchcloses immediatelly. After a short delay the atmospheric air pulse reaches to the water valve and the relief valve. Thewater valve closes and lets a certain level of water at the bottom in the bowl.After the flushing cycle has stopped the push button and the system will be ready for the next flush.

Discharge valve


Flushing ringWater valve

Water supplyconnection

Controlmechanism

Control hose

Bowl

Relief valve




OPERATION AND MAINTENANCEDate: Doc.18 May 2009 002251-1


Start-up• Clean the bottom of the toilet bowl.• Check that the mini-check valve and the discharge valve are clean and working correctly.• Check that the water supply hose and the filter of the water valve are not blocked up.• Check that sufficient vacuum (-0.3 bar) is available.• Open the water supply valve in the water supply piping.• Press the toilet push button. Pressing the button starts the flushing sequence. The discharge valve opens and

the contents of the bowl are extracted by vacuum. At the same time the bowl is rinsed by water.• When the discharge valve has been closed water level is restored in the bowl by the closing time delay of the

water valve.

Monitoring the vacuum toilet in the normal operation• Check that the water valve provides the rinse water to the bowl at the same time as the discharge valve extracts

the bowl contents when the push button is pressed.• Check that the push button returns to it´s non-activated state.• Check that after the discharge valve closes, the water valve continues to provide water to the bowl. If the water

valve time delay is correctly adjusted, there should be a pool of water at the bottom of the bowl.• Check that there are no water or air leaks.

! NOTE: Water consumption is dependent on the water supply pressure and the vacuum level.

Preparation for a toilet not to be used for a long period• Close the water supply valve.• Run a flush cycle by pressing the push button.• Close the toilet seat cover.

Water valve

Discharge valve

Push button

Controlmechanism

Mini-checkvalve

Direction A

Seat cover

Filter of the water valve

Water supply piping

Water supply valveA






Operation

The toilet is flushed by pressing the push button. The pneumatic push button is connected to the control mechanismwith a control hose, which transports the air pulse from the push button to the control mechanism.The air pulse starts the flushing sequence and the control mechanism connects vacuum to the control connectionsof the water valve and the discharge valve. The water valve opens and lets rinsing water flow into the bowl through theflushing ring.After a short delay vacuum acts in discharge valve housing and forces the rubber diaphragm in discharge valve to open.Contents of the bowl is drained to the vacuum sewer by a pressure difference between the bowl and vacuum sewer.The flushing cycle in the control mechanism starts the closing cycle. Vacuum enters to the relief valve.The relief valve opens the port between athmospheric air and the discharge valve.Athmospheric air enters to the discharge valve witch closes immediatelly. After a short delay the atmospheric air pulsereaches to the water valve and the relief valve. The water valve closes and lets a certain level of water at the bottom inthe bowl. After the flushing cycle has stopped the push button and the system will be ready for the next flush.

Discharge valve


Flushing ring Water valve

Water supplyconnection

Controlmechanism

Controlhose

Bowl

Relief valve





5775500 CONTROL MECHANISM, EVAC 910, WALL MODELS AND FLOOR MODELS

Description of the flushing sequence

In the standby position FIG.1

The control valve 1 is closed. Vacuum in the chambers 2 and3 is equalized by the jets 4 and 5. Force of the spring 6 holdsthe mechanism in a non-activated position.

In the position immediately after the push button hasbeen pressed FIG.2

Air pressure applied from the flush button to the chamber 7has lifted the lever 8 and opened control valve 1. Atmosphericair has entered chamber 3 through filter 9 and valve 1. Theforce from the pressure difference between 2 and 3 has movedthe shaft 10 to the left and the following sequence of eventshas occured:

The inlet valve 11 has closed. Vacuum valve 12 has opened.Vacuum is distributed via check valve 13 to discharge valve18 and water valve 19 which will both open. Chamber 14 isalso subjected to vacuum through check valve 21.

This vacuum will pull lever 8 and close valve 1 and the timerfunction will start. Chamber 3 will be evacuated through jet 5and the pressure difference 2-3 equalizes. At a certain level,the counterforce from spring 6 will outweigh and the cycle willgo in the opposite direction:

The vacuum valve 12 will close. The air inlet valve 11 will openand vacuum will enter the relief valve 22, athmospheric airenters the water valve, the discharge valve and the chamber14. The discharge valve 18 will close and somewhat later(because of the jet 17), the water valve 19 closes when asuitable water level has been reached at the bottom of thebowl. The relief valve closes.

Returning to the standby position FIG.3

The whole system goes to standby position ready for anotherVT-flush.

! NOTE: Diaphragm 16 has the same effective area as the airinlet valve 11 to balance the vacuum forces. FIG.3

! NOTE: Check valve 13 ensures that connected valves inactivated position are unaffected by changes in the vacuumsupply level.

! NOTE: If vacuum is too low or absent the function is delayed.Control valve 1 stays open until chamber 14 is subject tovacuum.





5775500 CONTROL MECHANISM, EVAC 910 WALL MODELS AND FLOOR MODELS

Operation

The functioning of the vacuum toilet is entirely controlled by the control mechanism. The operation of the controlmechnism is based on vacuum in the sewage piping system.Description of flushing sequence see document 002030-1.Jet 1 (document 002030-1 pos. 5) controls the discharge valve opening time.Jet 2 (document 002030-1 pos. 4) counters the effect of quick changes in the vacuum supply.Jet 3 (document 002030-1 pos. 15) delays the vacuum changes in the chamber 14 (see document 002030-1).Thisprevents a new flushing procedure to start before the previous procedure has stopped.

MaintenanceMaintenanceMaintenanceMaintenanceMaintenance

Check that the air filters 4 and 5 are not blocked.Check hoses and pipe connections for leaks.

Toilet discharge time

Jet 1 Short discharge period Red jet 1.5 sec.Normal discharge period Blue jet 2.0 sec.Longer discharge period White jet 2.5 sec.Less restriction shortens the time

Water valve opening time

Jet 6 Normal bowl water level White jetLow bowl water level Blue jet

Push button

Filter 4

Jet 1

Jet 2

Control mechanism

Jet 6(inside plastic cover)

Water valve

Discharge valve

Mini-check valve

Filter 5(athmospheric air inlet for relief valve)

Jet 3

Control mechanism

Relief valve




OPERATION AND MAINTENANCEDate: Doc.22 Oct 2008 002033-2

6543002 DISCHARGE VALVE, EVAC 910, WALL MODELS AND FLOOR MODELS

Operation

Closed condition:The control mechanism shuts off connection between the vacuum piping and the discharge valve housing. As thevalve housing is under atmospheric pressure the spring-loaded closing mechanism closes the rubber diaphragm andisolates the bowl from the vacuum piping.

Open condition:As the control valve opens the discharge valve housing is subjected to vacuum, thus forcing the closing mechanismto open. This in turn allows the rubber diaphragm to open, and connects the bowl to the vacuum pipe line.

Closing sequence:The vacuum pulse enters to the relief valve. The relief valve opens the port between athmospheric air and the dischargevalve. Athmospheric air enters to the discharge valve witch closes immediatelly. After a short delay the atmosphericair pulse reaches to the water valve and the relief valve. The water valve closes and lets a certain level of water at thebottom in the bowl.

Maintenance

See document 002034-1 for scheduled maintenance.

CLOSEDCONDITION

Closingmechanism

Control mechanism

Bowlside

Vacuumpiping

Vacuum hose

Connectionpipe

OPEN CONDITION CLOSING SEQUENCE

Rubber diaphragm

Rubbersleeve

Rubbersleeve

Relief valve

Dischargevalve

Discharge valve

Atmospheric air




MAINTENANCEDate: Doc.06 Jul 2009 002034-3

EVAC 910, WALL MODELS AND FLOOR MODELS

Cleaning instruction for the seat

• The seat is easy to clean, with just a few simple directions for you to observe.• Use a mild soap solution or biological cleaners.• Seat and hinges should not be left damp, but be dried with a soft cloth.• When using abrasive, corrosive or chlorine based cleaners for the bowl, avoid contact with the seat and hinges.

Therefore, when cleaning the bowl, make sure that seat and cover are in an upright position until all the cleaner hasbeen flushed away.

Scheduled maintenance program

Maintenance Program is based on 20 toilet flushes per day and 20 years operation.

Every year:• Change flap of Mini-check valve in every toilet.• Check operation, push button, seat and cover, rinse pattern, discharge pattern.• Check possible water and vacuum leakage.• Clean Filter ( not in USPH models ) in water supply.

Every 5 years:• Change Flap of mini-check valve in every toilet.• Open and clean Water valve filter 5774150.• Clean Control mechanism air filter 5778600.• Check operation, push button, seat and cover, rinse pattern, discharge pattern.• Check possible water and vacuum leakage.• Check Flushing ring 6541025 or 6540968 and flushing operation.

Every 10 years:• Change Flap of mini-check valve in every toilet.• Change Discharge valve rubbers: Rubber sleeve 6542990 (2pcs), Rubber diaphragm 6542989 and Diaphragm 6543134

in relief valve.• Change Water valve diaphragm 5774400.• Open and clean Water valve filter 5774150.• Clean Control mechanism air filter 5778600.• Check operation, push button, seat and cover, rinse pattern, discharge pattern.• Check possible water and vacuum leakage.• Check Flushing ring 6541025 or 6540968 and flushing operation.

! NOTE: Use only genuine Evac spare parts.

Discharge valve Water sypply Control mechanism

Flushing ring

Floor models:6541025 Flushing ring

Wall models:6540968 Flushing ring

5778600Air filter

Water valve5774400Diaphragm

5774150Filter

6541458Push button

5860303Push button

Pneumatic push buttons

6542990Rubbersleeve

6542989Rubberdiaphragm

Mini-checkvalve

FilterRelief valve

6544996Push button




TROUBLE SHOOTINGDate: Doc.

Filter ( not in USPH models )

04 Jun 2008 002031-2

EVAC 910, WALL MODELS

Push button

Water valve

Discharge valve

Vacuumhose

Control mechanism

Mini-check valve

Flushing ring

Shut-off valve

Seal ( not in USPH models )

Vacuum breakerWater supply hose

TroubleToilet is discharging continuously(discharge valve open)

Bowl does not become emptywhen flushed

No water or too little rinsingwater

Toilet is overflowing

Toilet does not flush.

Cause• Foreign object in bowl or

in discharge valve• Blocked air relief tubing• Quick relief valve malfunction

• Discharge valve blocked

• Leak in discharge valve housing• Discharge pipe blocked• Rubber sleeves leaking

• Water shut-off valve closed• No water pressure• Filter full or dirt in water valve• Flush ring loose• Flush ring clogged• Filter blocked up in water supply• Water valve jammed in open

position• Bowl clogged or discharge valve not

operating• Misuse (buckets of water thrown in

the bowl)• Too low vacuum (less than 30%) to

flush• No vacuum or low vacuum (less

than 30kPa)• Clogged mini-check valve• No impulse from push button• Jammed control mechanism• Jammed quick relief valve

Remedy• Shut off the problematic branch line

valve• Remove foreign object• Change discharge valve• Check and if necessary change

control mechanism• Check relief valve operation• Clear stoppage, if any, in discharge

valve• Sharp tools may damage rubber• Check that rubber sleeves are

undamaged and correctly fitted• Check relief valve operation• Open valve• Provide water pressure• Clean filter• Connect flushing ring• Clean flushing ring• Clean filter• Close water shut-off valve• Clean / change water valve nozzles,

springs, rubbers• Discharge bowl, valve and piping

with normally flushing

• Check vacuum level, removeblockage in piping

• Clean / change mini-check valve• Check hoses andmembrane of push

button• Change control mechanism• Check air filter condition. It should

be place.• Check relief valve operation

Relief valve




TROUBLE SHOOTINGDate: Doc.06 Jun 2008 002050-1

EVAC 910, FLOOR MODELS

TroubleToilet is discharging continuously(discharge valve open)

Bowl does not become emptywhen flushed

No water or too little rinsingwater

Toilet is overflowing

Toilet does not flush.

Cause• Foreign object in bowl or

in discharge valve• Blocked air relief tubing• Quick relief valve malfunction

• Discharge valve blocked

• Leak in discharge valve housing• Discharge pipe blocked• Rubber sleeves leaking

• Water shut-off valve closed• No water pressure• Filter full or dirt in water valve• Flush ring loose• Flush ring clogged• Filter blocked up in water supply• Water valve jammed in open

position• Bowl clogged or discharge valve not

operating• Misuse (buckets of water thrown in

the bowl)• Too low vacuum (less than 30%) to

flush• No vacuum or low vacuum (less

than 30kPa)• Clogged mini-check valve• No impulse from push button• Jammed control mechanism• Jammed quick relief valve

Remedy• Shut off the problematic branch line

valve• Remove foreign object• Change discharge valve• Check and if necessary change

control mechanism• Check relief valve operation• Clear stoppage, if any, in discharge

valve• Sharp tools may damage rubber• Check that rubber sleeves are

undamaged and correctly fitted• Check relief valve operation• Open valve• Provide water pressure• Clean filter• Connect flushing ring• Clean flushing ring• Clean filter• Close water shut-off valve• Clean / change water valve nozzles,

springs, rubbers• Discharge bowl, valve and piping

with normally flushing

• Check vacuum level, removeblockage in piping

• Clean / change mini-check valve• Check hoses andmembrane of push

button• Change control mechanism• Check air filter condition. It should

be place.• Check relief valve operation

Filter ( not in USPH models )

Push button

Water valve

Discharge valve

Vacuumhose

Control mechanism

Mini-check valveFlushing ring

Shut-off valve

Seal ( not in USPH models )

Vacuum breaker

Water supply hose

Relief valve






Removal of the discharge valve (wall models)

1. Remove the bowl.2. Disconnect the rubber hose A from the water valve

or from the connecting nipple (only in USPHmodels).

3. Loose (only in USPH models) water valve from thecomponent plate.

4. Disconnect the hose C with the elbow from therelief valve.

5. Unscrew two screws**.

Hose A

Water valve

Hose B

Elbow

Connectingnipple

Relief valve

Hose C

Screw**

Fig. 1 Fig. 2

1. Disconnect the water supply hose from the watervalve and the discharge pipe from the backplate.

2. Unscrew two screws* (see fig.2).3. Disconnect the rubber hose A from the water valve

or from the hose nipple (only in USPH models).4. Loose (only in USPH models) water valve from the

component plate.5. Disconnect the hose from the relief valve.6. Unscrew two screws** (see fig.1).

From the cabin side: From the service space side:

Screws*

Watervalve

Discharge pipe

Water supplyhose

Back plate

Removal of the discharge valve (floor models)

Water supply valve

Water hose

Pipes

Rubber bend

Screws***Water valve

Connection nipples

Vacuum breaker(USPH models)

Back plateVacuum breaker(not in USPH models)

Discharge piping

1. Close the water supply valve.2. Disconnect the water hose from the water valve.3. Disconnect the pipes of the vacuum breaker from

the connection nipples4. Disconnect the toilet from the rubber bend.5. Remove the toilet if needed.6. Remove the screws***.7. Disconnect the rubber hose A from the water valve

or the connecting nipple (only in the USPHmodels).

8. Remove the back plate.

Componentplate

Discharge valve






Dismantling of the discharge valve

Rubber sleeve

Cover

Spring

Rubber sleeve

Cover

Spring

Press

Press

Discharge valve body

Closing mechanism

Rubber sleeve and brace

Fig. 3 Fig. 4

1. Remove the rubber sleeves, the covers and the springs.(see fig.3).

2. Press lightly the closing mechanisms and remove therubber sleeve with the brace (see fig.4).

9. Loose (only in the USPH models) water valvefrom the component plate.

10. Disconnect the hose from the relief valve.11. Unscrew two screws*.

Rubber hose A Connecting nipple(only in USPH models)

Water valve

Componentplate

Hose B(only in USPH models)

Elbow

Hose C

Relief valve

Screws*

Discharge valve




SPARE PARTSDate: Doc.15 May 2008 002035-1

6543418 EVAC 910, WALL MODEL, PRESTIGE SILENT, WHITE6543419 EVAC 910, WALL MODEL, MOSAIK, WHITE

! NOTE: *When ordering:Toilet bowl - state type and standard colourSeat and cover - state type and standard colour

P/N 6543418 includes Prestige seat and cover (P/N 6542928)P/N 6543419 includes Mosaik seat and cover (P/N 6540973)

5432548Vacuum breaker

5431884Shut-off valve

6540936Edge strip

5990759Nut (x2)

5779098Guiding nut (x2)

5433594Hose clamp (x2)

5433572Connection sleeve

6540972 INSTALLATION KIT

6540967*Toilet bowl,includes flushing ring, springand hose clamp

6540968Flushing ring

5805900Hose to push button

6541458Push button

6542981Back plate assembly(document 002039-1)

6540973*Seat and cover,Mosaik

6542928*Seat and cover,Prestige

6542402Hose clamp

5432728Seal

5980801WATER SUPPLY KIT

5433215Water connectionhose with twoseals

6542318Spring

6543414Filter




SPARE PARTSDate: Doc.

6542318Spring


05 Dec 2008 002040-1


P/N 6543420 includes Prestige seat and cover (P/N 6542928)P/N 6543421 includes Mosaik seat and cover (P/N 6540973)P/N 6544766 includes Open front seat and cover (P/N 5441801)

6540936Edge strip

5990759Nut (x2)

5779098Guiding nut (x2)


5433572Connection sleeve

6540972 INSTALLATION KIT

Connectionhose withseals

Shut-off valve

6542928*Seat and cover,Prestige

6541458Pneumatic push button

6540973*Seat and cover,Mosaik

654982Back plate( document 002039-3)

6540968Flushingring

5805900Hose to push button

6540967*Toilet bowl,includes flushing ring, spring and hose clamp

6542402Hose clamp

Vacuumbreaker

5441801*Seat and cover,Open front

6541772WATER SUPPLY KIT(document 6:01024i)




SPARE PARTSDate: Doc.21 Oct 2009 002266-1



6543060*Toilet bowl,includes flushing ring,spring and hose clamp

5433215Water connectionhose with twoseals

5432548Vacuumbreaker


5980801 WATER SUPPLY KIT

5432728Seal

6541922*Seat and cover, Silent(EvacInhush),(with metal hinges)

5442101*Seat and cover, Aniara

P/N 6545825 includes Silent (EvacInhush) seat and cover (P/N 6541922)P/N 6545826 includes Aniara seat and cover (P/N 5442101)

5433266Wood screw5 x 45, (x2)

or

6542983Back plate(document 002043-2)

6544996Pneumaticpush button

6542402Hose clamp


6544769Rubber bend

6544897INSTALLATION KIT

5990724Nut M8, (x2)

5825300Plastic washer, (x2)

6542318Spring


6543414Filter

See recommended spare part kits in spare part document:Doc no. 001923-1 Water valve

6544898Plug

2618192Bolt

P/N 6543422 is replaced by P/N 6545825P/N 6543423 is replaced by P/N 6545826






6541922*Seat and cover,Silent(EvacInhush),with metal hinges

6542984Back plate(document 002043-2)

5980802WATER SUPPLY KIT( document 6:01024 i )

VacuumbreakerUSPH

Connectionhose withseals

Shut-offvalve

5433594Hose clamp

6544769Rubber bend

6544897INSTALLATION KIT

5433266Wood screw5x45, (x2)

5990724Nut M8, (x2)


5442101*Seat and cover,Aniara

P/N 6543424 is replaced by P/N 6545827P/N 6543425 is replaced by P/N 6545828P/N 6544797 is replaced by P/N 6545829

P/N 6543424 includes Silent (EvacInhush) seat and cover (P/N 6541922)P/N 6543425 includes Aniara seat and cover (P/N 5442101)P/N 6544797 includes Open front seat and cover (P/N 5441801)


6542402Hose clamp

6543060Toilet bowl,includes flushing ring,spring and hose clamp

5825300Plastic washer, (x2)

or

6542318Spring


5441801Seat and cover,Open front

See recommended part kitsin spare part document:Doc no. 001923-2 Water valve

2618192Bolt

6544898Plug





6542981 BACK PLATE ASSEMBLY, EVAC 910, WALL MODELS6542982 BACK PLATE ASSEMBLY, EVAC 910, WALL MODELS USPH

5775500Control mechanism

Valve seat

O-ring

Valve flap6545051VALVE STEM KIT

6543072Back plate

5736326Hose, L=270

6543002Discharge valve

5507000Elbow

Hose

6542997Water valve

5481004Hose, L=390(only in part 6542982)

6542402Hose clamp(only in part 6542982)

6545052MINI-CHECKVALVE KIT

Hose

Hose

Nut and hose nipple(only in part 6542982)

6542995Wall support,left and right




SPARE PARTSDate: Doc.17 Jul 2008 002043-2

6542983 BACK PLATE, EVAC 910, FLOOR MODELS6542984 BACK PLATE, EVAC 910, FLOOR MODELS USPH

5775500Control mechanism

Valve seat

O-ring

Valve flap6545051VALVE STEM KIT

6543072Back plate(not including support plate)

5736326Hose, L=270

6543002Discharge valve

5507000Elbow

Hose

6542997Water valve

5481004Hose, L=390(only in part 6542984)

6542402Hose clamp(only in part 6542984)

6545052MINI-CHECKVALVE KIT

Hose

Hose

Nut and hose nipple(only in part 6542984)

Support plate




SPARE PARTSDate: Doc.28 Sep 2009 002038-2

6543002 DISCHARGE VALVE

6543127Brace6545041

Spare part kit

6543133Air valve cover

6543132Cover

6544240Spring

6542991Spring

6542987Single yoke

6542985Housing

6542986Double yoke

6542988Yoke cover

6542991Spring





6542997 WATER VALVE

6543030 RECOMMENDED SPARE PART KIT:1 x 3790009 V-ring1 x 5774150 Filter1 x 5774400 Diaphragm1 x 5774701 Valve washer + Jet

5774400Diaphragm

5774500Slider

5774800Permanent magnet

5522700Conic spring

5774300Bottom

5774150Filter

6542998Solenoid valve

3790009V-ring

5990740Screw

5774600Cover

3752211O-ring

Valve washer

Jet

5774701Valve washer + Jet

6542826Membrane




SPARE PARTSDate: Doc.08 Dec 2008 6:132 i

5775500 CONTROL MECHANISM5881000 SPARE PART KIT FOR THE CONTROL MECHANISM

5778000Jet carrier complete

5778001Jet carrier complete

5778001 Jet carrier complete (as standard), which controls flushing period

Alternative for this jet available:5778000 Jet carrier complete*5778002 Jet carrier complete*5778004 Jet carrier complete*

5778600Air filter

*Jet Carrier identification:P/N Colour Size Effect5778004 Yellow 0.20 Extra long flushing period5778000 White 0.30 Long flushing period5778001 Blue 0.40 Normal flushing period5778002 Red 0.50 Short flushing period

! NOTE: See also document 3:111 i, Control mechanism for Evac 900 model toilets.See also document 002032-1, Control mechanism for Evac 910 model toilets.

P/N 5775500 Control mechanism

P/N 5881000 Spare part kit for the control mechanism:

P/N Description Pcs5778600 Air filter 15778001 Jet carrier complete 25778000 Jet carrier complete 15778700 Filter 15959902 Mini-check valve 1




SPARE PARTSDate: Doc. 01 Jan 2010 6:01122F

6542928 PRESTIGE, SEAT AND COVER, EVACINHUSH FOR EVAC 900 AND 910 WALL MODEL TOILETS

! NOTE: Seat and cover sold as complete only.

Prestige seat and cover fulfills ANSI Z124.5 - 1997 [ Plastic Toilet ( Water closet ) Seats ] requirements.

6542950HINGE KIT

6542951Clamping bush

6545761Buffer for cover (x2)

6545760Buffer for seat (x4)

6545946Straps




SPARE PARTSDate: Doc.03 Apr 2008 6:01019E

6540973 SEAT AND COVER, MOSAIK, EVAC 900 AND EVAC 910, WALL MODEL

! NOTE; When ordering: Seat and cover -state type and colour.


2 x Hinge body

2 x Nut

6542726Hinge kit




SPARE PARTSDate: Doc.14 Jul 2008 6:01021F

5442101 SEAT AND COVER, ANIARA FOR EVAC 90 WALL AND FLOOR MODELS, EVAC 900 AND EVAC910 FLOOR MODELS

! NOTE: When ordering: Seat and cover -state type and colour.


5442601 (x2)Hinge pin

5442801Hinge body, left

5442701Hinge body, right

5445201 (x2)Nut

6542732HINGE KIT




SPARE PARTSDate: Doc.14 Jul 2008

6541922 EVACINHUSH, SILENT SEAT AND COVER FOR EVAC 90 WALL AND FLOOR, EVAC 900 ANDEVAC 910 FLOOR MODELS

5446401 (x2)Hinge pin

6541241 (x2)Hinge

5445201 (x2)Nut

6540931 (x2)Washer

P/N 5446101 is replaced by P/N 6541922.


! NOTE; When ordering: Seat and cover -state type and colour.

6:01109C




SPARE PARTSDate: Doc.11 Apr 2008 6:01024 i

6541772 WATER SUPPLY KIT, USPH, FOR EVAC 900 AND EVAC 910 TOILETS, WALL MODELS5980802 WATER SUPPLY KIT, USPH, FOR EVAC 90, EVAC 900 AND EVAC 910 TOILETS, FLOOR MODELS

P/N 6541772 Water supply kit, USPH


5433215Water connection hose(includes: 2 x seal )


6541409 VACUUM BREAKER COMPLETE, USPH,WALL MODEL

P/N 5980802 Water supply kit, USPH

5910601 (x2)Cu pipe Ø12x1

5431884Shut- off valve

5430164Elbow


5430166Coupling G1/2

5432728Gasket

5430166Coupling

5957210Elbow wallfast flange

5435336 VACUUM BREAKER ASSEMBLY, USPH

5430166Coupling 5433215

Water connection hose(includes: 2 x seal)

5432728Seal

5432728Seal




SPARE PARTSDate: Doc.20 Oct 2009 6:01012K

6541458 PNEUMATIC PUSH BUTTON, EVAC 900 AND EVAC 910, WALL MODELS6541057 OPTIONAL PNEUMATIC PUSH BUTTON KIT, EVAC 900 AND EVAC 910, FLOOR MODELS

5430105Installation kit

5430108Protecting pipe


P/N 6541458 Pneumatic push button

P/N 6541057 Optional pneumatic push button kit

6543767Cover plate

6541272Bellows

6540932Spring

6541457Button

P/N 6540917 is replaced by P/N 6541458




SPARE PARTSDate: Doc.18 May 2009 002255-1

6544996 PNEUMATIC PUSH BUTTON FOR EVAC 910 FLOOR MODELS

6542438Button

6544997Connection flange

3510100Bellows complete

6542449Locking ring

VACUUM TOILET · NOTE: Evac 910 vacuum toilets with the Mosaik, Aniara or Open front seats and...

Documents

Transcript of VACUUM TOILET · NOTE: Evac 910 vacuum toilets with the Mosaik, Aniara or Open front seats and...