V E H I C L E F L A S H E R

O B D - I I S TA L K • C H R Y S L E R V E H I C L E S

�������������

USER MANUAL | V1.3

OBD-II MODULE INSTALLATION

1. Connect the module into the vehicle’s OBD-I I port. The OBD-I I port is located on the dashboard under the steering wheel .

2. Turn the vehicle on or into the run posit ion.

3. The module wi l l begin to boot and the red LED wi l l flash for 5 seconds.

4. When the module is ready to use the green LED wi l l b l ink for 5 seconds and then turn of f.

5. I f you need to disconnect the module plug it back in you wi l l need to fol low the boot sequence again.

WARRANT Y: • This warranty protects the product(s) specified to be free from defects in materia l and workmanship

for 1(one) year. During the warranty period we wi l l , at our sole discretion, repair or replace the product(s). This l imited warranty does not cover travel expense or labor charges for the removal and reinstal lat ion of the product, or any other charges al ike. We are not responsible for incidental damages, including but not l imited to: loss of t ime, loss of work, inconvenience, loss and/or damage to personal property, shipping expenses. We are in no way responsible for any loss or any indirect or consequentia l damages result ing from any such defect in materia l and/or workmanship whether it ’s due to negl igence, incorrect instal lat ion, or manufacturer mistake. It is the sole responsibi l ity of the party in it iat ing a warranty cla im to pay shipping charges associated with returning a product.

WARNING :• If you do not know what you are

doing, do not try.

• We advise professional instal lat ion for al l products.

• Electrical shock can cause injury or death. Please use proper tools and protection when instal l ing. Professional instal lat ion is strongly advised.

• Please check for correct instal lat ion method before powering on. Electrical fire can occur.

• Do not run any wires in the way of a ir bags or other safety devices.

COMPATIBILIT Y Ram 1500 11-18Ram 2500 11-18Ram 3500 11-18Durango 11-18Charger 15-18Chal lenger 16-18Grand Cherokee 11-18300 15-18

2. You can remove the 3 screws and remove the entire module. Or reach your hand behind and remove the plugs from the module.

3. Remove the two plugs in the security module and reconnect to the bypass module. Remember: hold onto the security module for vehicle servic ing.

1. Remove the panel to access under the dash

1. Remove the push pins holding passanger side carpet si lencer panel in place.

2. Remove both connectors plugged into security gateway module.

3. Plug in security bypass block into Existing Connectors and tuck up inside. Reinstal l push pins holding si lencer panel in place. Remember: hold onto the security module for vehicle servic ing.

ALL OTHER 2018 CHRYSLERS

2018 JEEP GRAND CHEROKEE & 2018 DURANGO The security gateway module located on the passenger side under the glove box.

4. The security module is located directly behind the radio. You can remove the 3 screws and remove the entire module. Or reach your hand behind and remove the plugs from the module.

5. Remove the two plugs in the security module and reconnect to the Z-Flash bypass module. Remember: hold onto the security module for vehicle servic ing.

1. Remove the two bolts under the rubber pad

2. Remove the front panel covering the radio

3. Remove the 4 bolts securing the radio

GATEWAY MODULE INSTALLATION

2018 RAM

SOFT WAREThe Z-Flash includes a free sof tware download. This sof tware is used for module updates, disabl ing l ights, and bui ld ing custom flash patterns!

2. Press “configure device” to access the configuration sof tware

3. You can disable any l ights you do not want to flash. You can also enable or disable any flash patterns you don’t want to use

5. Using the custom flash pattern tab you can bui ld your own flash pattern from start to finish. When you’re done you can save the fi le and share it with fr iends!

4. You can program the module whi le it is plugged into your vehicle and test each flash pattern

1. Download the configuration sof tware from thezflash.com

Jump in:

1. When entering the vehicle pul l the high beam stalk back whi le starting the vehicle.

2. The l ights wi l l immediately turn on when the vehicle starts

QUICK START ACTIVATIONS

PATTERN CHANGING

1. To change the pattern press both the lef t arrow and cancel button simultaneously.

2. The flash pattern wi l l be displayed on the dashboard if your dashboard screen is set to view the radio.

Key Fob: Use the key fob to turn your l ights on by pressing

1. Unlock 3. Lock

2. Unlock 4. Unlock

OPERATIONNormal Operation: The module requires no external switches and can activate with the high beam stalk.

1. Pul l the high beam stalk back for 5 seconds to activate it . You' l l know it 's turned on when the high beam indicator is active on the dashboard. If your vehicle is equipped with a dashboard screen it wi l l d isplay the Z-Flash pattern that you are currently using.

2. To turn it of f pul l the high beam stalk for two seconds

FAQs• How does it work?: Using diagnostic signals the module tel ls the vehicle to activate the respective

l ights. The module does not rewrite computer code or ef fect the vehicle. The codes are the same that the dealer could use to diagnose your vehicle.

• Will this burn my computer?: The module does not put out any voltage and wi l l not burn up the computer. It 's much l ike plugging a USB stick into your PC.

• Will my brake l ights stil l work?: Your brake and turn signals wi l l override the flashing pattern. If the module is active and you hit the brakes or use your turn signal , that function wi l l override. This cannot be disabled as it is an important safety feature.

• Does this put my vehicle in reverse?: The module wi l l not change your vehicle’s gears. However, some vehicle's may activate the backup camera screen because they are wired in with the reverse l ights. Unfortunately this cannot be disabled at this t ime.

• Will this burn up my bulbs?: L ike any headl ight/tai l l ight flasher it wi l l burn out your bulbs faster than

normal. Af termarket HIDs wi l l burn up very quickly because the bal lasts are not intended to flash.

• Can I change the flash pattern?: Currently the module is set to one flash pattern and cannot be changed.

• Can I flash my tail l ights?: I f your vehicle has a separate bulb for the tai l l ights and brake l ights, then only the brake l ight wi l l flash. If your vehicle has one bulb for both, then that bulb wi l l flash.

• My bulb is not flashing or very dim: Unl ike LEDs, Halogen bulbs require a charge up and cool down t ime. Because of this it is not possible to flash them as fast as LED bulbs. Try using a custom pattern to slow the flash rate down.

• Is the module traceable?: Once removed, the module does not leave any trace of being instal led. For 2018 model years be sure to remove the gateway module and reconnect the vehicle's security module before attempting to connect an OBD-I I scanner or before having the vehicle serviced. Leaving the gateway module instal led wi l l prevent an OBD-I I scanner from operating properly.