USB Game Pad Manual
-
Upload
shelby-pozernick -
Category
Documents
-
view
100 -
download
0
Transcript of USB Game Pad Manual
![Page 1: USB Game Pad Manual](https://reader035.fdocuments.in/reader035/viewer/2022081801/54ea41134a795910478b4f06/html5/thumbnails/1.jpg)
USB GAMEPAD
Instruction Manual
1. System Requirements:
a. Support USB port
b. Compatible with Windows 98/ME/2000/XP
c. DirectX7.0 version or up
2. Program Installation:
Program installation under the Windows98/WindowsME/Windows2000/WindowsXP operating system:
a. Enter Windows, insert disk, double click SETUP, and then install the driving program according to
instruction of computer.
b. Start → Control Panel → Game controller
c. Connect USB plug of controller with a free USB socket on computer →computer will find the driving
program “USB GAMEPAD” automatically → Attribute
3. Test Page:
1) Enter “Test Page”
A. Testing fire buttons 1~12
Press any button among 1 to 12 of the controller, the corresponding button in testing page will turn red.
B. Testing Direction button:
Digital Mode: Press up, down, left, right, 45°, 135°, 225°, 315° arrow of the Direction button, the X/Y
Axes in the testing page will move correspondingly.
Analog Mode: Press up, down, left, right, 45°, 135°, 225°, 315° arrow of the Direction button, the
“Pov Info” in the testing page will indicate 8 directional arrows correspondingly.
C. Test Left/right 3D rocker:
� Digital mode (LED is off): left 3D rocker is X/Y axis’ function, and axis is always in digital mode, right
3D rocker is 1-4 key’s function.
� Analog mode (LED is on): left 3D rocker is X/Y axis’ function, right 3D rocker is Z/RZ axis’ function,
and axes are always in analog mode.
D. In “Vibration Test” Page, you can test the vibration of right and left motor
2) Enter “Setting” Page for calibration:
This setting is only used under analog mode (LED is on) when cross cursor is not in the center position.
If cross cursor is not in the center position of X/Y Axes panel, click ”default” first, and click “calibration”,
then operate according to the instruction of computer.
3) To set auto turbo function
a. Buttons 1~12 can be defined as auto turbo function.
b. Press “AUTO button + any fire button” simultaneously for the first time, the fire button will be with
auto turbo function. Then press the defined fire button, the corresponding LED flashes at a certain
frequency, meanwhile, this fire button bears auto continuous shooting.
c. Press “Clear button + any defined fire button” simultaneously for the second time, then the defined
function button’s auto turbo function is cleared up.
![Page 2: USB Game Pad Manual](https://reader035.fdocuments.in/reader035/viewer/2022081801/54ea41134a795910478b4f06/html5/thumbnails/2.jpg)
5. Trouble shooting:
Problem description Proposed solution
The hardware does not work after
the installation
a) Check the connection with the PC USB port
b) Go to Control panel -> System -> Hardware tab -> Device
manager. Check the setting “HID device” of your device, it should be
“Confirmation”, and the setting “ID” should be “1”. Check the
converter I/O settings and make sure they do not conflict with your
other peripherals
c) Try to reboot your PC.
The driver cannot be installed or
does not work after installation
Check your DirectX version. Version 7.0 or higher is required.
Having started the game, some
analog axes do not work or
operate erratically
Check whether the device is properly calibrated (Note: in the inactive
state all the axis cursors should be positioned in the center).
There is no vibration a) Check your DirectX version. Version 7.0 or higher is required.
b) Try to restart the game or reboot your PC
No driver is found after the game
pad is connected to the USB port
Most probably caused by problems during installation or software
conflicts with some other existing drivers. Check if any devices in
Device manager (Control panel -> System -> Hardware tab ->
Device manager) were not recognized (they will be shown with
exclamation mark “!” before them). Delete these devices, reinstall
the software driver and connect the converter again.
Upon starting the game, the right
motor keeps vibrating
Turn the engine down under the game “Force feedback” options
Upon starting the game, the
vibration gets weaker
Adjust the vibration intensity using controls “STICK VOLUME”,
“ROAD EFFECTS” and such like under the game “Force feedback”
options