USB GAMEPAD

Instruction Manual

1. System Requirements:

a. Support USB port

b. Compatible with Windows 98/ME/2000/XP

c. DirectX7.0 version or up

2. Program Installation:

Program installation under the Windows98/WindowsME/Windows2000/WindowsXP operating system:

a. Enter Windows, insert disk, double click SETUP, and then install the driving program according to

instruction of computer.

b. Start → Control Panel → Game controller

c. Connect USB plug of controller with a free USB socket on computer →computer will find the driving

program “USB GAMEPAD” automatically → Attribute

3. Test Page:

1) Enter “Test Page”

A. Testing fire buttons 1~12

Press any button among 1 to 12 of the controller, the corresponding button in testing page will turn red.

B. Testing Direction button:

Digital Mode: Press up, down, left, right, 45°, 135°, 225°, 315° arrow of the Direction button, the X/Y

Axes in the testing page will move correspondingly.

Analog Mode: Press up, down, left, right, 45°, 135°, 225°, 315° arrow of the Direction button, the

“Pov Info” in the testing page will indicate 8 directional arrows correspondingly.

C. Test Left/right 3D rocker:

� Digital mode (LED is off): left 3D rocker is X/Y axis’ function, and axis is always in digital mode, right

3D rocker is 1-4 key’s function.

� Analog mode (LED is on): left 3D rocker is X/Y axis’ function, right 3D rocker is Z/RZ axis’ function,

and axes are always in analog mode.

D. In “Vibration Test” Page, you can test the vibration of right and left motor

2) Enter “Setting” Page for calibration:

This setting is only used under analog mode (LED is on) when cross cursor is not in the center position.

If cross cursor is not in the center position of X/Y Axes panel, click ”default” first, and click “calibration”,

then operate according to the instruction of computer.

3) To set auto turbo function

a. Buttons 1~12 can be defined as auto turbo function.

b. Press “AUTO button + any fire button” simultaneously for the first time, the fire button will be with

auto turbo function. Then press the defined fire button, the corresponding LED flashes at a certain

frequency, meanwhile, this fire button bears auto continuous shooting.

c. Press “Clear button + any defined fire button” simultaneously for the second time, then the defined

function button’s auto turbo function is cleared up.

5. Trouble shooting:

Problem description Proposed solution

The hardware does not work after

the installation

a) Check the connection with the PC USB port

b) Go to Control panel -> System -> Hardware tab -> Device

manager. Check the setting “HID device” of your device, it should be

“Confirmation”, and the setting “ID” should be “1”. Check the

converter I/O settings and make sure they do not conflict with your

other peripherals

c) Try to reboot your PC.

The driver cannot be installed or

does not work after installation

Check your DirectX version. Version 7.0 or higher is required.

Having started the game, some

analog axes do not work or

operate erratically

Check whether the device is properly calibrated (Note: in the inactive

state all the axis cursors should be positioned in the center).

There is no vibration a) Check your DirectX version. Version 7.0 or higher is required.

b) Try to restart the game or reboot your PC

No driver is found after the game

pad is connected to the USB port

Most probably caused by problems during installation or software

conflicts with some other existing drivers. Check if any devices in

Device manager (Control panel -> System -> Hardware tab ->

Device manager) were not recognized (they will be shown with

exclamation mark “!” before them). Delete these devices, reinstall

the software driver and connect the converter again.

Upon starting the game, the right

motor keeps vibrating

Turn the engine down under the game “Force feedback” options

Upon starting the game, the

vibration gets weaker

Adjust the vibration intensity using controls “STICK VOLUME”,

“ROAD EFFECTS” and such like under the game “Force feedback”

options