Twin City Fan - BSI-DSI Square Inline Centrifugal Usage Guide
1
BSI/DSI Square Inline Centrifugal Usage Guide Refer to the Twin City Fan Revit Family Usage Guide for details on how to load a family into a project. Once loaded the default discharge option is ‘1’ which corresponds to rear discharge. The user can change the discharge option to any one of 7 available configurations by changing the numeric value in the discharge option field. Table 1 describes each configuration. Note that Revit recognizes all duct connections on the fan regardless of the discharge option selected. For example, a rear discharge will have Left and Right duct connections in the model despite the fact that they have no mounting collars and are not valid mounting options. It is important to ensure the correct discharge option is selected and that the duct work, transitions, etc. are in the correct mounting locations. Also, CFM values must be entered for all three discharges. Non-applicable discharges are set to ‘0 CFM’. Although there are only 7 discharge options available, Revit will allow the user to enter numeric values larger than 7 in this field. Any value greater than 7 will result in an invalid discharge. How It Works Twin City Fan’s square inline centrifugal models BSI and DSI have a unique discharge option parameter within Revit. This field allows the user to select the appropriate discharge for the application. 5959 TRENTON LANE NORTH • MINNEAPOLIS, MN 55442-3237 PHONE: 763-551-7600 • FAX: 763-551-7601 WWW.TCF.COM User must en- ter CFM values for all applica- ble discharges. Discharge Option is set to a numer- ic value from 1 to 7. See Figure 1 below. } Figure 1 *Note: All discharge options are as viewed from the fan inlet. Discharge Option* 1 2 3 4 5 6 7 Description Rear Discharge Left Discharge Right Discharge Left and Right Discharge Left and Rear Discharge Right and Rear Discharge Left, Right and Rear Discharge Image INLET REAR INLET LEFT INLET RIGHT LEFT RIGHT INLET INLET LEFT REAR INLET REAR RIGHT RIGHT INLET REAR LEFT Table 1* For assistance with Twin City Fan Revit models, please send an email to [email protected].
description
Twin City Fan’s square inline centrifugal models BSI and DSI have a unique discharge option parameterwithin Revit. This field allows the user to select the appropriate discharge for the application.
Transcript of Twin City Fan - BSI-DSI Square Inline Centrifugal Usage Guide
BSI/DSI Square Inline Centrifugal Usage Guide
Refer to the Twin City Fan Revit Family Usage Guide for details on how to load a family into a project. Once loaded the default discharge option is ‘1’ which corresponds to rear discharge. The user can change the discharge option to any one of 7 available configurations by changing the numeric value in the discharge option field. Table 1 describes each configuration. Note that Revit recognizes all duct connections on the fan regardless of the discharge option selected. For example, a rear discharge will have Left and Right duct connections in the model despite the fact that they have no mounting collars and are not valid mounting options. It is important to ensure the correct discharge option is selected and that the duct work, transitions, etc. are in the correct mounting locations. Also, CFM values must be entered for all three discharges. Non-applicable discharges are set to ‘0 CFM’.
Although there are only 7 discharge options available, Revit will allow the user to enter numeric values larger than 7 in this field. Any value greater than 7 will result in an invalid discharge.
How It Works
Twin City Fan’s square inline centrifugal models BSI and DSI have a unique discharge option parameter within Revit. This field allows the user to select the appropriate discharge for the application.
5959 TrenTon Lane norTh • MinneapoLis, Mn 55442-3237phone: 763-551-7600 • Fax: 763-551-7601
www.TcF.coM
User must en-ter CFM values for all applica-ble discharges.
Discharge Option is set to a numer-ic value from 1 to 7. See Figure 1 below.
}
Figure 1
*Note: All discharge options are as viewed from the fan inlet.
Discharge Option*
1 2 3 4 5 6 7
Description Rear Discharge Left Discharge Right DischargeLeft and Right
DischargeLeft and Rear Discharge
Right and Rear Discharge
Left, Right and Rear Discharge
ImageINLET
REAR
INLET LEFT
INLET
RIGHT
LEFT
RIGHT
INLET
INLET LEFT
REAR
INLET
REAR RIGHT
RIGHT
INLET
REAR
LEFT
Table 1*
For assistance with Twin City Fan Revit models, please send an email to [email protected].
