TV Stand Instruction Manual
Transcript of TV Stand Instruction Manual
Model: PSFS04
TV Stand Instruction ManualV2.0
Thank you for choosing this PERLESMITH product! At PERLESMITH we strive to provide you with the best quality products and services in the industry. Please share your experience of our product with others at www.perlesmith.com/pages/reviews if you are satisfied. Should you have any issues, please don't hesitate to contact us.Technical Support:1-800-556-6806 Mon-Fri 10am - 5pm (PST) (USA) (CAN)Other Info:[email protected] (US)[email protected] (CA)
Website: www.perlesmith.com
01
Check the VESA Pattern of TV before the Installation
100 mm ≈ 4 in.200 mm ≈ 7 7/8 in.300 mm ≈ 11 3/4 in.400 mm ≈ 15 3/4 in.600 mm ≈ 23 5/8 in.
Minimum VESA pattern: 100mm/4 in.(W)x100mm/4 in.(H)
If your TV VESA is greater than 600x400 mm/23.6x16in. or less than VESA 100x100mm/4x4 in., this TV stand is NOT compatible.
MAX: 600mm/23.6 in.
MAX
: 400
mm
/16
in.
Tools Needed (Not lncluded)
• Philips Screwdriver
IMPORTANT SAFETY INFORMATIONPlease carefully read all instructions before attempting installation. If you do not understand the instructions or have any concerns or questions, please contact customer service at [email protected] (US)/ [email protected] (CA). • Check package contents against Supplied Parts and Hardware List to assure that all components were received undamaged. Do not use damaged or defective parts. If you require replacement parts, contact customer service at [email protected] (US)/ [email protected] (CA).• Not all parts and hardware included will be used. • Do not use this product for any purpose or in any configuration not explicitly specified in this instruction. We hereby disclaim any liability for injury or damage arising from incorrect assembly, incorrect mounting, or incorrect use of this product.• Please check www.perlesmith.com for more products and company information.
If this TV stand is NOT compatible, please contact customer service at [email protected] (US)/ [email protected] (CA) to find a compatible product.
Serious or fatal crushing injuries can occur from tip over. To help prevent tip over:● Never allow children to climb, stand, hang, or play on any part of TV or TV stand.● Use tip over restraint or anchor stand to wall.Use of tip over restraints may only reduce, but not eliminate risk of tip over.
Tip over Warning
02
Supplied Parts and Hardware
Supplied Parts
Tempered Glass Base
Tempered Glass Base
x11Support Pillar
x23Support Pillar
x24x22Foot
x25Support Pillar
x16
Support Pillar
x17Support Pillar
x110Support Pillar
x19
M6x470mmConnecting Rod
x215
M8x465mmConnecting Rod
x216x214Transfer Plate
x211Foot Cover
Supplied Hardware for Assembling the TV stand
M8x22mmBolt
M8Nut
M8x16mmBolt
M8Rubber Washer
x2A
M10 Nutx2D1
Decorative Capx2D2
Cable Clipx2E
13/64 in. (5mm)Allen Key
x1B1
17#Wrench
x1B2 x2C1 x2C2 x2C3
13# Wrenchx1F1
Foot
x18
x217
M10x620mmConnecting Rod
Supplied Hardware for Attaching TV Brackets to TV
M6x15mmBolt
x4S1
Mounting Bracekta x2
Steel Cableb x1
Long Screwc x1
Short Boltd x1
Plastic Anchore x1
M6x30mmBolt
x4S2
M8x20mmBolt
x4S3
M8x50mmBolt
x4S4
M6/M8Washer
x4S5
Supplied Parts and Hardware for Attaching the TV stand to the wall (Optional)
x112TV Plate
x213TV Bracket
Boltx1F2
L16mmSpacer
x4S6-1
L22mmSpacer
x4S6-2
03
x11
1
15
15
M6x470mmConnecting Rod
Tempered Glass Base
x2
16
Step 1 Screw the Connecting Rods [15 and 16] to the Tempered Glass Base [1]
M8x465mmConnecting Rod
x2
15
16
x23Support PillarSupport Pillar
x1
Step 2 Slide the Support Pillars to the Connecting Rods
6
No Spacer
36
Note: Make sure the two connecting rods can pass through the two holes at the top of the support pillar [6]
3
16
Back
04
Note: Make sure the side with the small hole on the support pillar [7] faces the back of the stand
4
47
Note: Make sure the two connecting rods can pass through the two holes at the top of the support pillar [7]
Front
4Support Pillar
2Tempered Glass
Base Support Pillarx17
x2
x1
2
Step 3 Secure Tempered Glass Base [2] and the Support Pillar [4 and 7] to the Connecting Rods
05
1
1
2
2
x12
2
FootTempered Glass
Basex2
Step 4 Secure Tempered Glass Base [2] and the Feet [5 and 8] to the Connecting Rods
5
x18Foot CoverFoot
x2
x2 13/64 in. (5mm)Allen Key
M8x22mmBolt
x1
11
A B1
B1
x2M10x620mmConnecting Rod
Step 5 Secure the Connecting Rod [17] to the Tempered Glass Base [1]
Make sure matte side of tempered glass base [2] faces upward as shown in this figure
Turn Over
17
17
Down
UP5
811
A
2
2
1
06
1
Step 6 Secure Support Pillar [9 and 10] to the Tempered Glass Base [1]
x1Support PillarSupport Pillar
x1
x2 17#WrenchTransfer Plate
x1
x2Decorative CoverM10 Nut
x2D1 D2
B2 D2D1
9
9
14
14
14
x1TV Plate
Step 7 Attach the Washer [C1] to TV Plate [12]
x2M8Rubber Washer
Attach the rubber washer [C1] to the center of top and bottom of the TV Plate [12]. Make sure the hole of washer [C1] is align with the center hole on the TV Plate [12].
Note: Make sure the side with the small hole on the support pillar [9] faces the back of the stand
Please don’t fully tighten nuts [D1] until Step 8 to fix all the bolts in the right holes.
Side View
B2
12
12
C1
C1
C1 12
Back
Front
10
10
C1
07
x2 M8Nut
M8x16mmBolt
x2
Step 8 Secure the TV Plate [12] Support Pillar
x1 13#Wrench
13/64 in. (5mm)Allen Key
x1
Make sure all the bolts are fully tightened before putting on your TV.The hole on the TV Plate [12] should be aligned with the hole on the Transfer Plate [14].
F1B1
C2 C3
Side View
F
C2
C2
C3
C3
15
B1
C1
08
M6x15mmS1 x4
M6x30mmS2 x4
Note: The bolts are shown in accordance with the actual size
TV Bolts (Only one bolt size fits your TV)
M8x50mmS4 x4
M8x20mmS3 x4
Note: The spacers are shown in accordance with the actual size
Select TV BoltsOnly one bolt size fits your TV.
M6 M8
Step 8 Secure the TV Brackets [13] to TV
M6
M8
TV Bracketx213
M6/M8WasherS5 x4
L16mmSpacer
S6-1 x4
L22mmSpacer
S6-2 x4
09
Bolt length: Verify adequate thread engagement with bolts or bolts/spacers combination. We recommend thread engagement by at least 5 turns.-Too short will not hold the TV.-Too long will damage the TV.
Too Long Correct CorrectToo Short
Please Note: The provided TV bolts meet most of today’s TVs design. However, some TVs require special bolts which may not be in the hardware bag. In this case we offer our “PSUHP" Universal Hardware Kit which provides a large selection of bolts that can meet the demand of older and unique applications.Please Note: When using the spacers it is important to note that they can be used in multi-layers (meaning stacked). If you have any difficulty understand-ing how to install the TV bolts or spacers, please contact customer service at [email protected] (US)/ [email protected] (CA).
CAUTION: Ensure the TV brackets [13] are EQUALLY CENTERED on your TV and securely fastened in place.
Please note: The bolt hole locations on your TV may vary in accordance of the manufacturers design of the TV. We are only illustrating possible locations of the bolt holes.
13
Option A (For Flat Back TV)
S5
S1/S3
10
Option D
Option B (For Round Back TV)
Spacers may be necessary for 2 holes ONLY.Option C (For TV with A “Bump”)
For cable interference or inset holes, use spacers [S6-1] and [S6-2] to create extra space between the TV and TV brackets
S5
S2/S4
S6-1/S6-2
S1/S3
S5
S2/S4
S6-1/S6-2
S5
AlternateSpacerSetups
S5
S2/S4
S6-1/S6-2
AlternateSpacerSetups
AlternateSpacerSetups
11
Philips Screwdriver
(Not lncluded)
①
②
TV brackets are two-height-adjustable.You can choose the proper height.
Step 9-1 Hang the TV with brackets to the TV plateStep 9-2 Push the bottom of the TV to TV plateStep 9-3 Tighten the bolts [F2] until the bolts touch the TV plate.
Manage the wires
The First ChoiceThe Second Choice
③
HEAVY! You may need assistance with this step.
Step 9 Secure TV to TV Plate [12] and Manage the Wires
EF2
x2Cable Clip
EBolt
x2F2
12
If necessary, the TV plate or TV can be swivelled manually.
Step 10 Adjust the Swivel Angle
Step 11 Attach the TV Stand to the Wall (Optional)
WALL
This unit is just for sample display.
Note: It is recommend to use this tipping restraint to attach this unit to the wall, to prevent possible accidents and/or injuries.
Solid Concrete or Concrete Block
Wood Studs
x2 x1
x1 x1
x1Plastic Anchore
Long Screwc
Mounting Bracketa
Steel Cableb
Short Boltd
Thank you again for
choosing this PERLESMITH product!
All of us at PERLESMITH do appreciate your product purchase. We hope that you are as happy with your product as we are designing and manufacturing it for you. We strive to provide you with the best quality products and services in the industry. Please share your experience of our product with others at www.perlesmith.com/pages/reviews if you are satisfied. Should you have any issues, please don't hesitate to contact us.
Technical Support: 1-800-556-6806 Mon-Fri 10am - 5pm (PST) (USA) (CAN)
Other Info: [email protected] (US)/[email protected] (CA)
Please check www.perlesmith.com for more products and company information.
Perlesmith offers productsin these categories
Anti-tip StrapsTV Stands AV Shelves
Speaker Stands TV Carts
Full Motion Mounts Tilt Mounts Corner Mounts
Please remember us when you need one.
Perlesmith offers productsin these categories
Anti-tip StrapsTV Stands AV Shelves
Speaker Stands TV Carts
Full Motion Mounts Tilt Mounts Corner Mounts
Please remember us when you need one.