Torque Value for Nylon 2
-
Upload
ajay-bhaarath -
Category
Documents
-
view
218 -
download
0
Transcript of Torque Value for Nylon 2
-
7/23/2019 Torque Value for Nylon 2
1/3
Torque Table Guide
Suggested Tightening
Torque Values for Nonferrous
Threaded Fasteners
Torque Table
The following suggested tightening torques provide an excellent starting point for
determining torque requirements.
Remember, you may need to increase or reduce these numbers based on the individual
joint.
Bolt Size
18-8
Stainless
Steel
Brass Silicon
Bronze
Aluminum
2024-T4
316 Stainless
Steel Monel Nylon
2 56 2.5 2.0 2.3 1.4 2.6 2.5 0.44
2 64 3.0 2.5 2.8 1.7 3.2 3.1
3 48 3.9 3.2 3.6 2.1 4.0 4.0
3 - 56 4.4 3.6 4.1 2.4 4.6 4.5
4 - 40 5.2 4.3 4.8 2.9 5.5 5.3 1.19
4 - 48 6.6 5.4 6.1 3.6 6.9 6.7
5 - 40 7.7 6.3 7.1 4.2 8.1 7.8
5 - 44 9.4 7.7 8.7 5.1 9.8 9.6
6 - 32 9.6 7.9 8.9 5.3 10.1 9.8 2.14
6 - 40 12.1 9.9 11.2 6.6 12.7 12.3
8 - 32 19.8 16.2 18.4 10.8 20.7 20.2 4.30
8 - 36 22.0 18.0 20.4 12.0 23.0 22.4
10 - 24 22.8 18.6 21.2 13.8 23.8 25.9 6.61
10 - 32 31.7 25.9 29.3 19.2 33.1 34.9 8.20
-
7/23/2019 Torque Value for Nylon 2
2/3
1/4" - 20 75.2 61.5 68.8 45.6 78.8 85.3 16.00
1/4" - 28 94.0 77.0 87.0 57.0 99.0 106.0 20.80
5/16" - 18 132.0 107.0 123.0 80.0 138.0 149.0 34.90
5/16" - 24 142.0 116.0 131.0 86.0 147.0 160.0
3/8" - 16 236.0 192.0 219.0 143.0 247.0 266.0
3/8" - 24 259.0 212.0 240.0 157.0 271.0 294.0
7/16" - 14 376.0 317.0 349.0 228.0 393.0 427.0
7/16" - 20 400.0 327.0 371.0 242.0 418.0 451.0
1/2" - 13 517.0 422.0 480.0 313.0 542.0 584.0
1/2" - 20 541.0 443.0 502.0 328.0 565.0 613.0
9/16" - 12 682.0 558.0 632.0 413.0 713.0 774.0
9/16" - 18 752.0 615.0 697.0 456.0 787.0 855.0
5/8" - 11 1110.0 907.0 1030.0 715.0 1160.0 1330.0
5/8" - 18 1244.0 1016.0 1154.0 798.0 1301.0 1482.0
3/4" - 10 1530.0 1249.0 1416.0 980.0 1582.0 1832.0
3/4" - 16 1490.0 1220.0 1382.0 958.0 1558.0 1790.0
7/8" - 9 2328.0 1905.0 2140.0 1495.0 2430.0 2775.0
7/8" - 14 2318.0 1895.0 2130.0 1490.0 2420.0 2755.0
1" - 8 3440.0 2815.0 3185.0 2205.0 3595.0 4130.0
1" - 14 3110.0 2545.0 2885.0 1995.0 3250.0 3730.0
11/8" - 7 413.0 ft-lbs 337.0 383.0 265.0 ft-lbs 432.0 ft-lbs 499.0
-
7/23/2019 Torque Value for Nylon 2
3/3
ft-lbs ft-lbs ft-lbs
1-1/8" - 12 390.0 ft-lbs 318.0
ft-lbs
361.0
ft-lbs
251.0 ft-lbs 408.0 ft-lbs
1-1/4" - 7 523.0 ft-lbs 428.0
ft-lbs
485.0
ft-lbs
336.0 ft-lbs 546.0 ft-lbs 627.0
ft-lbs
1-1/4" - 12 480.0 ft-lbs 349.0
ft-lbs
447.0
ft-lbs
308.0 ft-lbs 504.0 ft-lbs 575.0
ft-lbs
1-1/2" - 6 888.0 ft-lbs 727.0
ft-lbs
822.0
ft-lbs
570.0 ft-lbs 930.0 ft-lbs 1064.0
ft-lbs
1-1/2" - 12 703.0 ft-lbs 575.0
ft-lbs
651.0
ft-lbs
450.0 ft-lbs 732.0 ft-lbs 840.0
ft-lbs
This table is offered as the suggested maximum torquing values for threaded products and is only a guide. Actual tests were
conducted on dry or near-dry products. Mating parts were wiped clean of chips and foreign matter. A lubricated bolt requires less
torque to attain the same clamping force as a nonlubricated bolt. All values shown on chart except for nylon represent a safe working
torque; in the case of nylon only, the fi gures represent breaking torque.
AIR AUTOMATION ENGINEERING
230 Commerce Circle South, P.O. Box 32709, Fridley, MN 55432
(763) 571-4970, (800) 231-9205, Fax (763) 571-4923
Web Site: www.airautomation.com
E-mail: [email protected]