TM RTA-RX-F-SC Radio Frequency Controller LISTED 243CTM Visual Environment Control system accepts...

72
Attention Contractors... Radio Frequency Visual Environment Control System Installer’s Guide A Step-by-Step Guide for Installing, Operating and Maintaining a Complete Lutron RadioTouchTM Visual Environment Control System 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 CLASS 2 LOW VOLTAGE WIRING 1 2 3 4 5 Power Status Program Burn-In 1 2 3 General Lights ON OFF Sivoia Cntrl 1 Sivoia Cntrl 2 RTA-RX-F-SC Radio Frequency Controller LISTED 243C Ind. Cont. Eq. Coopersburg, PA 18036 STATUS INDICATOR OPERATION ON - Burn-in Mode Slow Blink -Normal Operation Mode Fast Blink - Program Mode Very Fast Blink - Receiving RF Data RadioTouch 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Occ. Com Signal 15V 24V Circuit Com Sw Closure 1 Sw Closure 2 Sw Closure 3 Sw Closure 4 Sw Closure 5 Closure Com 0-10 Purple 0-10 Gray Receiver Settings Terminal connections are Class 2. TM Occ. Sensor 0-10 V Shade Switch Closures 12345 Powered When Lit Status Indicator Program Button Burn-in Button RECEIVER SWITCH SETTINGS 1. UP-Preset Lock DN.-Preset Adj. 2. UP-Occ. Sensor DN.-Emerg. Set. 3. UP-FDB Mode DN.-ECO Mode 4. UP-OFF DN.-Min. Light 5. UP-Auto ON DN.-Manual ON See Installers Guide for System Addressing and Programming Instructions ® 123 Shade Settings SHADE SWITCH SETTINGS 1. UP-A/C Shades DN.-Normal Oper. PS Signal © 2000-2002 Lutron Electronics Co., Inc.

Transcript of TM RTA-RX-F-SC Radio Frequency Controller LISTED 243CTM Visual Environment Control system accepts...

  • Attention Contractors...

    Radio Frequency VisualEnvironment Control SystemInstaller’s GuideA Step-by-Step Guide for Installing,Operating and Maintaining a CompleteLutron RadioTouchTM Visual Environment Control System

    1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

    CLASS 2 LOW VOLTAGE WIRING

    1 2 3 4 5 Power Status Program Burn-In1 2 3

    General

    Lights

    ON

    OFF

    Siv

    oia

    Cn

    trl 1

    Siv

    oia

    Cn

    trl 2

    RTA-RX-F-SCRadio Frequency Controller

    LISTED 243CInd. Cont. Eq.

    Coopersburg, PA 18036

    STATUS INDICATOR OPERATIONON - Burn-in ModeSlow Blink -Normal Operation ModeFast Blink - Program ModeVery Fast Blink - Receiving RF Data

    RadioTouch

    1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

    Occ

    . Co

    m

    Sig

    nal

    15V

    24V

    Cir

    cuit

    Co

    m

    Sw

    Clo

    sure

    1

    Sw

    Clo

    sure

    2

    Sw

    Clo

    sure

    3

    Sw

    Clo

    sure

    4

    Sw

    Clo

    sure

    5

    Clo

    sure

    Co

    m

    0-10

    Pu

    rple

    0-10

    Gra

    y

    ReceiverSettings

    Term

    inal

    co

    nn

    ecti

    on

    sar

    e C

    lass

    2.

    TM

    Occ. Sensor 0-10 V Shade Switch Closures

    1 2 3 4 5

    PoweredWhen Lit

    StatusIndicator

    ProgramButton

    Burn-inButton

    RECEIVER SWITCH SETTINGS1. UP-Preset Lock DN.-Preset Adj.2. UP-Occ. Sensor DN.-Emerg. Set.3. UP-FDB Mode DN.-ECO Mode4. UP-OFF DN.-Min. Light5. UP-Auto ON DN.-Manual ON

    See Installers Guide for SystemAddressing and Programming Instructions

    ®

    1 2 3

    ShadeSettings

    SHADE SWITCH SETTINGS1. UP-A/C Shades DN.-Normal Oper.

    PS

    Sig

    nal

    © 2

    000-

    2002

    Lut

    ron

    Ele

    ctro

    nics

    Co.

    , Inc

    .

  • 2 Step by Step instructions for RadioTouch Controller

    Overview

    1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16CLASS 2 LOW VOLTAGE WIRING

    1 2 3 4 5 Power Status Program Burn-In

    ON

    OFF

    1 2 3

    OR

    OR

    Incandescent or MagneticLow-Voltage Interface

    Tu-Wire® Interface

    Tabletop TransmittersWallbox Transmitters

    DescriptionThe RadioTouchTM Visual Environment Control systemaccepts inputs from multiple Radio Frequency (RF)transmitters, occupant sensors, and a photosensor tocontrol zones of lighting, AC Motorized Window Treat-ments, and other equipment controlled by switchclosure outputs.

    System RatingsVoltage – 120VAC or 277VAC, 60 Hz

    Current – Fully loaded 20 Amp circuit breaker(16 Amps) of Lutron Dimming Ballast Load(RTA-RX-F and RTA-RX-F-SC).

    16 Amps maximum for switchingincandescent, electronic fluorescent ballasts,magnetic fluorescent ballasts, and HID usingthe RadioTouch Switchpack (RTA-RX-SW).

    Switch Closure Outputs – Not to exceed 30VDC and1/3 Amp.

    Inputs Controller Outputs

    Fluorescent Lighting Load

    • Phase control for Lutron Hi-lume® andEco-10TM dimming ballasts.

    • 0-10 Volt control for Lutron 0-10 Voltdimming ballasts, 40 ballast maximum.

    Tu-Wire® Dimming Ballast, Incandescent,Electronic Low-Voltage or Magnetic Low-Voltage Loads

    • 2000 W/VA of Incandescent or MagneticLow-Voltage loads can be controlled usingthe Incandescent Interface (FDI-INC-2000)

    • 1000 W of Electronic Low-Voltage loadscan be controlled using the Electronic Low-Voltage Interface (FDI-ELV-1000)

    • 16A of Lutron Tu-Wire® dimming ballastscan be controlled using the Tu-Wire®Interface (FDI-FTU-16A-120)

    Switch Closure Output(RTA-RX-F-SC only)

    • 5 Class 2 momentary drycontact closures.

    • To raise/lower amotorized projectionscreen, etc.

    • AC Motorized WindowTreatments, etc.

    Lutron Shades(RTA-RX-F-SC only)

    • Sivoia® window treatments

    AC MotorController

    OccupantSensors

    Siv

    oia

    Cn

    trl 1

    Siv

    oia

    Cn

    trl 2

    RTA-RX-F-SCRadio Frequency Controller

    LISTED 243CInd. Cont. Eq.

    Coopersburg, PA 18036

    STATUS INDICATOR OPERATIONON - Burn-in ModeSlow Blink -Normal Operation ModeFast Blink - Program ModeVery Fast Blink - Receiving RF Data

    RadioTouch

    1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

    Occ

    . Co

    m

    Sig

    nal

    15V

    24V

    Cir

    cuit

    Co

    m

    Sw

    Clo

    sure

    1

    Sw

    Clo

    sure

    2

    Sw

    Clo

    sure

    3

    Sw

    Clo

    sure

    4

    Sw

    Clo

    sure

    5

    Clo

    sure

    Co

    m

    0-10

    Pu

    rple

    0-10

    Gra

    y

    ReceiverSettings

    Term

    inal

    co

    nn

    ecti

    on

    sar

    e C

    lass

    2.

    TM

    Occ. Sensor 0-10 V Shade Switch Closures

    1 2 3 4 5

    PoweredWhen Lit

    StatusIndicator

    ProgramButton

    Burn-inButton

    RECEIVER SWITCH SETTINGS1. UP-Preset Lock DN.-Preset Adj.2. UP-Occ. Sensor DN.-Emerg. Set.3. UP-FDB Mode DN.-ECO Mode4. UP-OFF DN.-Min. Light5. UP-Auto ON DN.-Manual ON

    See Installers Guide for SystemAddressing and Programming Instructions

    ®

    1 2 3

    ShadeSettings

    SHADE SWITCH SETTINGS1. UP-A/C Shades DN.-Normal Oper.

    PS

    Sig

    nal

    © 2

    000-

    2002

    Lut

    ron

    Ele

    ctro

    nics

    Co.

    , Inc

    .

    Photosensor

    ElectronicLow-Voltage Interface

  • 3Step by Step instructions for RadioTouch Controller

    Table of Contents

    Step-by-Step InstructionsHardware Installation Page

    Step 1: System wiring requirements ................................... 5

    Step 2: Checking the line voltage ....................................... 6

    Step 3: For retrofits, checking the lamp socketsfor dimming compatibility ........................................ 6

    Step 4: Ballast and fixture wiring ........................................ 7

    Step 5: Checking for proper socket wiring .......................... 7

    Step 6: Determining a mounting location for theRadioTouchTM Controller ......................................8-9

    Step 7: Wiring in Bypass ................................................... 10

    Step 8: Testing the circuit .................................................. 11

    Step 9A: Wiring the RadioTouchTM Controllerfor each zone of lighting ..................................11-12

    Step 9B: Wiring the RadioTouchTM Controllers formultiple lighting zones .......................................... 13

    Step 10: Wiring the RadioTouchTM SwitchpackControllers for each zone ..................................... 14

    Step 11A: Wiring the RadioTouchTM Controller inBypass using Load Interfaces .............................. 15

    Step 11B: Wiring the RadioTouchTM Controller usingLoad Interfaces ..................................................... 16

    Step 11C: Mounting the Load Interface ................................. 17

    Step 12: Mounting the RadioTouchTM Controller ................. 17

    RadioTouchTM antenna positioning ........................ 17

    Step 13: Testing the RadioTouchTM Controller ..................... 18

    Step 14: Wallbox Transmitter wiring .................................... 18

    Step 15: Mounting the Wallbox Transmitters ....................... 19

    Step 16: Addressing the Wallbox Transmitter to theController .........................................................19-20

    Step 17: Installing Occupant Sensors ................................. 21

    Step 18: Wiring the Occupant Sensor ...........................22-23

    Step 19: Configuring the Controller for an unoccupiedlight level ............................................................... 24

    Step 20: Configuring the Controller for Manual ON orAutomatic ON occupant sensor operation ............ 24

    Step 21: Determine the mounting location for thePhotosensor ......................................................... 25

    Step 22: Mounting the Photosensor ................................... 25

    Step 23: Wiring the Photosensor ........................................ 26

    Step 24: Testing the Photosensor ....................................... 26

    Step 25: Setting the Photosensor for the space ................. 27

    Step 26: Wiring to Lutron Sivoia® Motorized WindowTreatments ......................................................28-29

    Step 27: Setting Sivoia® shade presets .............................. 30

    Step 28: Wiring output switch closures to otherequipment ............................................................. 31

    Step 29: Wiring and setup for AC Motorized WindowTreatments ......................................................32-35

    Step 30: Wiring and setup for AC Motorized ProjectionScreens ...........................................................36-39

    Step 31: Configuring the motor direction on the AC MotorController .............................................................. 40

    Step 32: Wiring the RadioTouchTM Controller for usewith a GRAFIK Eye® System ................................ 41

    Step 33A: Mounting the Tabletop Transmitter using theWall Bracket (optional) ......................................... 42

    Step 33B: Mounting the Tabletop Transmitter using theSecurity Clip (optional) ....................................43-44

    Step 34: Addressing the Tabletop Transmitter ...............44-45

    Step 35: Labeling the Tabletop Transmitter ........................ 46

    System Calibration

    Step 36: Burn-in new fluorescent lamps ............................. 47

    Advanced Programming & System Configuration

    Addressing a Wallbox Transmitter ........................................49-50

    Addressing a Tabletop Transmitter .......................................51-52

    Deleting a Wallbox Transmitter .............................................53-54

    Deleting a Tabletop Transmitter ............................................55-56

    Deleting all Transmitters from a Controller ................................ 57

    Setting the High End Light Level on a Controller ...................... 57

    Adjusting Preset Light Levels - Remote Method ....................... 58

    Adjusting Preset Light Levels - DIP Switch Method .................. 59

    Setting the ON Light Level of an RTA-WX-2B - RemoteMethod ...................................................................................... 60

    Setting the ON Light Level of an RTA-WX-2B - DIP SwitchMethod ...................................................................................... 60

    Setting the dimmable Controller to operate with LutronHi-lume® FDB- or Eco-10TM ECO- Series dimming ballasts ....... 61

    Setting the Controller for Emergency ON Operation ................. 61

    Using RadioTouchTM Controllers to create preset lightingscenes ..................................................................................62-63

    Resetting the Controller Light Levels to Factory Defaults ......... 64

    Resetting the Controller to All Factory Default Settings ............ 64

    Reference SheetsLoad Wiring

    Wiring the Dimming Ballast(s) in Bypass ..........................65-66

    Wiring the (0-10Volt) Dimming Ballast(s) in Bypass ............... 67

    Fluorescent Ballast InformationFixture Voltage Map ............................................................... 68

    TroubleshootingTroubleshooting Guide ......................................................69-71

    Warranty and Technical AssistanceWarranty, Technical and Sales Assistance .............. Back Cover

  • 4 Step by Step instructions for RadioTouch Controller

    1 2 3 4 5 6 7 8

    CLASS 2 LOW VOLTAGE WIRING

    Burn-In1 2 3 4 5 Power Status Program

    OverviewThe RadioTouch System provides the ability to controlyour visual environment from any location in a space.The RadioTouch Controller controls your Lutron fluores-cent dimming ballasts directly and provides a direct linkto Lutron Sivoia® Motorized Window Treatments andother A/V equipment. The RadioTouch SwitchpackController is able to switch 16A of high inrush loads.One RadioTouch Controller is required for each zone oflighting.

    Controller ModelsRTA-RX-FThe RTA-RX-F can control one zone of lighting and ac-cept all inputs described below.

    RTA-RX-F-SCThe RTA-RX-F-SC has the same capabilities as theRTA-RX-F with the addition of a direct control link toSivoia® Motorized Window Treatments, low-voltageswitch closure outputs, and control AC Motorized Win-dow Treatments and AC Motorized Projection Screensthrough an interface.

    RTA-RX-SWThe RTA-RX-SW can switch one 16A high inrush light-ing circuit and accept inputs from Wallbox Transmitters,Tabletop Transmitters, and occupant sensors.

    Sensor/Control InputsWallbox Transmitters - The Wallbox Transmitter allowsthe user to dim the lights from full to minimum, set andaccess preset light levels (if addressed to a dimmablecontroller) and turn the lights ON or OFF. The WallboxTransmitters must be within 35 feet of the Controller.Some models of this control may also be used to controlMotorized Window Treatments, Motorized ProjectionScreens, etc. depending on model number. Multi-loca-tion control is achieved by simply adding more Wallbox

    1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

    CLASS 2 LOW VOLTAGE WIRING

    1 2 3 4 5 Power Status Program Burn-In1 2 3

    Hardware InstallationSystem Wiring

    Transmitters and addressing them to the Controller. Upto 16 Wallbox and Tabletop Transmitter zones can beaddressed to a Controller.

    Tabletop Transmitters - The Tabletop Transmitter allowsthe user to dim the lights from full to minimum, set andaccess preset light levels (if addressed to a dimmablecontroller), and turn the lights ON or OFF. Some modelsof this control may also be used to control AC MotorizedWindow Treatments, AC Motorized Projection Screens,etc. depending on model number. Multi location dimmingis available by simply adding more transmitters andaddressing them to the same Controller. The TabletopTransmitter is battery powered and may be locatedanywhere in a space within 35 feet of a Controller.

    Occupant Sensor - The optional occupant sensorsupplies a signal to the Controller any time the space isoccupied. This signal tells the lights controlled by theRadioTouch Controller to turn on. An unoccupied signaltells the RadioTouch Controller to turn lights off or go toa minimum level.

    Photosensor - The optional photosensor supplies asignal to the Controller indicating the ambient lightlevel. When enabled for use with a photosensor, theController will adjust lighting levels to a user definedsetting. A dimmable Controller must be installed andproperly wired to the photosensor.

    Burn-in - This button on the Controller activates a 100hour lamp maximum light level to season the lamps andensure long fluorescent lamp life. The Controller statusLED is ON when activated, and the RadioTouch Con-troller will automatically remove itself from Burn-in afterthe 100 hour period. During the Burn-in period, theWallbox and Tabletop Transmitters will only turn thelights ON and OFF. All other lighting functions areignored. The 100 hours are counted only while thelights are turned to full ON. The 100 hour counter iscancelled if the Controller is manually removed fromthis mode by pressing the Burn-in button again or if thepower to that Controller is removed.

    RTA-RX-F RTA-RX-F-SC RTA-RX-SW

    RTA-RX-FRadio Frequency Controller

    LISTED 243CInd. Cont. Eq.

    Coopersburg, PA 18036

    RadioTouchTM

    ®

    1 2 3 4 5See Installers Guide forSystem Addressing andProgramming Instructions

    STATUS INDICATOR OPERATIONON - Burn-in ModeSlow Blink -Normal Operation ModeFast Blink - Program ModeVery Fast Blink - Receiving RF Data

    RECEIVER SWITCH SETTINGS1. UP-Preset Lock DN.-Preset Adj.2. UP-Occ. Sensor DN.-Emerg. Set.3. UP-FDB Mode DN.-ECO Mode4. UP-OFF DN.-Min. Light5. UP-Auto ON DN.-Manual ON

    ReceiverSettings

    PoweredWhen Lit

    StatusIndicator

    ProgramButton

    Burn-inButton

    1 2 3 4 5 6 7 8

    Occ

    . Co

    m

    Sig

    nal

    15V

    24V

    Cir

    cuit

    Co

    m

    0-10

    Pu

    rple

    0-10

    Gra

    y

    Occ. Sensor 0-10 V

    PS

    Sig

    nal

    Term

    inal

    co

    nn

    ecti

    on

    sar

    e C

    lass

    2.

    © 2

    000-

    2002

    Lut

    ron

    Ele

    ctro

    nics

    Co.

    , Inc

    .

    1 2 3 4 5 6 7 8

    CLASS 2 LOW VOLTAGE WIRING

    1 2 3 Power Status Program Burn-In

    RTA-RX-SWRadio Frequency Controller

    LISTED 243CInd. Cont. Eq.

    Coopersburg, PA 18036

    RadioTouchTM

    ®

    1 2 3

    1 2 3 4 5 6 7 8

    Occ

    . Co

    m

    Sig

    nal

    15V

    24V

    Cir

    cuit

    Co

    m

    Occ. Sensor

    STATUS INDICATOR OPERATIONON - Burn-in ModeSlow Blink -Normal Operation ModeFast Blink - Program ModeVery Fast Blink - Receiving RF Data

    RECEIVER SWITCH SETTINGS1. UP-Preset Lock DN.-Preset Adj.2. UP-Occ. Sensor DN.-Emerg. Set.3. UP-Auto ON DN.-Manual ON

    ReceiverSettings

    PoweredWhen Lit

    StatusIndicator

    ProgramButton

    See Installers Guide forSystem Addressing andProgramming Instructions

    Term

    inal

    co

    nn

    ecti

    on

    sar

    e C

    lass

    2.

    © 2

    000-

    2002

    Lut

    ron

    Ele

    ctro

    nics

    Co.

    , Inc

    .

    Siv

    oia

    Cn

    trl 1

    Siv

    oia

    Cn

    trl 2

    RTA-RX-F-SCRadio Frequency Controller

    LISTED 243CInd. Cont. Eq.

    Coopersburg, PA 18036

    STATUS INDICATOR OPERATIONON - Burn-in ModeSlow Blink -Normal Operation ModeFast Blink - Program ModeVery Fast Blink - Receiving RF Data

    RadioTouch

    1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

    Occ

    . Co

    m

    Sig

    nal

    15V

    24V

    Cir

    cuit

    Co

    m

    Sw

    Clo

    sure

    1

    Sw

    Clo

    sure

    2

    Sw

    Clo

    sure

    3

    Sw

    Clo

    sure

    4

    Sw

    Clo

    sure

    5

    Clo

    sure

    Co

    m

    0-10

    Pu

    rple

    0-10

    Gra

    y

    ReceiverSettings

    Term

    inal

    co

    nn

    ecti

    on

    sar

    e C

    lass

    2.

    TM

    Occ. Sensor 0-10 V Shade Switch Closures

    1 2 3 4 5

    PoweredWhen Lit

    StatusIndicator

    ProgramButton

    Burn-inButton

    RECEIVER SWITCH SETTINGS1. UP-Preset Lock DN.-Preset Adj.2. UP-Occ. Sensor DN.-Emerg. Set.3. UP-FDB Mode DN.-ECO Mode4. UP-OFF DN.-Min. Light5. UP-Auto ON DN.-Manual ON

    See Installers Guide for SystemAddressing and Programming Instructions

    ®

    1 2 3

    ShadeSettings

    SHADE SWITCH SETTINGS1. UP-A/C Shades DN.-Normal Oper.

    PS

    Sig

    nal

    © 2

    000-

    2002

    Lut

    ron

    Ele

    ctro

    nics

    Co.

    , Inc

    .

  • 5Step by Step instructions for RadioTouch Controller

    Hardware InstallationSystem Wiring

    Step 1: System wiring requirementsReview system wiring requirements and ensure properwires are pulled for hardware installation. Each zone oflighting requires a RadioTouch Controller.

    Caution - Observe all local and nationalelectrical codes and Safety Standards.

    Note: The maximum wire length for the load circuit is250 feet from the RadioTouch Controller to the furthestdimming ballast.

    1 32

    1613*12

    9 10

    1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16CLASS 2 LOW VOLTAGE WIRING

    1 2 3 4 5 Power Status Program Burn-In1 2 3

    ON

    OFF

    (14*)

    4 65

    CircuitBreaker

    DistributionPanel

    (not included)

    Ground

    Neutral

    Hot

    Green

    (120V) Black

    Blue

    WhiteOrangeBlue

    WhiteOrangeBlack

    WhiteOrangeBlack

    WhiteOrangeBlack

    WhiteOrangeBlack

    NeutralDimmed HotSwitched Hot

    (277V) RedCap the wire thatis not being used

    (Red or Blackdepending oninput voltage)

    Class 2 Wiringeach wire is to be#18 AWG (1.0mm2)

    Line Voltage WiringLine Voltage Wiring

    Ground

    Ground

    FluorescentFixture

    (not included)

    OtherFluorescentFixture(s)

    (if applicable)

    Lutron Dimming Ballast

    Lutron Dimming Ballast

    Lutron Dimming Ballast

    Lutron Dimming Ballast

    Additional ballast for4 lamp fixtures only

    Additional ballast for4 lamp fixtures only

    Lutron FluorescentDimming Ballast

    Lutron FluorescentDimming Ballast

    WallboxTransmitter

    Ceiling Mount OccupantSensor (if applicable)

    TabletopTransmitter

    Lutron Sivoia®Shades (ifapplicable)

    AC Motorized Projection Screen orAC Motorized Window Treatments

    controlled by momentary switchclosures (if applicable)

    LutronAC MotorController

    120VPower

    LineVoltageWiring

    Siv

    oia

    Cn

    trl 1

    Siv

    oia

    Cn

    trl 2

    RTA-RX-F-SCRadio Frequency Controller

    LISTED 243CInd. Cont. Eq.

    Coopersburg, PA 18036

    STATUS INDICATOR OPERATIONON - Burn-in ModeSlow Blink -Normal Operation ModeFast Blink - Program ModeVery Fast Blink - Receiving RF Data

    RadioTouch

    1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

    Occ

    . Co

    m

    Sig

    nal

    15V

    24V

    Cir

    cuit

    Co

    m

    Sw

    Clo

    sure

    1

    Sw

    Clo

    sure

    2

    Sw

    Clo

    sure

    3

    Sw

    Clo

    sure

    4

    Sw

    Clo

    sure

    5

    Clo

    sure

    Co

    m

    0-10

    Pu

    rple

    0-10

    Gra

    y

    ReceiverSettings

    Term

    inal

    co

    nn

    ecti

    on

    sar

    e C

    lass

    2.

    TM

    Occ. Sensor 0-10 V Shade Switch Closures

    1 2 3 4 5

    PoweredWhen Lit

    StatusIndicator

    ProgramButton

    Burn-inButton

    RECEIVER SWITCH SETTINGS1. UP-Preset Lock DN.-Preset Adj.2. UP-Occ. Sensor DN.-Emerg. Set.3. UP-FDB Mode DN.-ECO Mode4. UP-OFF DN.-Min. Light5. UP-Auto ON DN.-Manual ON

    See Installers Guide for SystemAddressing and Programming Instructions

    ®

    1 2 3

    ShadeSettings

    SHADE SWITCH SETTINGS1. UP-A/C Shades DN.-Normal Oper.

    PS

    Sig

    nal

    © 2

    000-

    2002

    Lut

    ron

    Ele

    ctro

    nics

    Co.

    , Inc

    .

    * Depending onload, AC

    MotorizedShades orProjectionScreen.

    Ceiling Mount Photosensor(if applicable)

    Line Voltage Wiring

  • 6 Step by Step instructions for RadioTouch Controller

    Hardware InstallationBallast Wiring

    Step 2: Checking the line voltageIf this installation is a retrofit, compare the line voltagerating (on the label) of the existing ballast(s) to therating of the ballast(s) being installed. All ballasts mustbe rated for the same line voltage.

    Note - For Emergency Fixtures (fixtures that never turn offor have a battery back-up ballast in the fixture), call theLutron Technical Support Center, (800) 523-9466 forrestrictions and wiring requirements.

    Step 3: For Retrofits, Checking the Lamp Sockets for Dimming CompatibilityDetermine if the lamp sockets in the fixture need tobe replaced.

    Number of lampsper ballast

    1

    2

    3

    4

    Existing Non-Dimming Ballast(s) Information

    Warning - Operating the Dimming Ballast(s)with the wrong sockets in place will damagethe ballast(s) and void the warranty.

    Notes:

    • When replacing sockets, use Rapid Start sockets (aknife-edge variety, such as model #13053-UN byLeviton Mfg. Co., or a #660 Series by Triboro Mfg.Co., is recommended).

    • A Rapid Start, 1-lamp ballast will normally have 6wires — (1) Hot, (1) Neutral, (4) lamp wires. A 7thwire, the Ground, may be present depending upon themanufacturer. This type of ballast does not requirenew sockets.

    • Lutron ballasts must be located so that the maximumcase temperature is less than 75°C and the relativehumidity is less than 90%, non-condensing.

    • Avoid situations where strong cold air drafts blowdirectly on bare bulbs (minimum start temperature is10°C).

    • Good metal-to-metal contact between lamp pins andlamp holder contacts is necessary for proper dimmingperformance. Knife-edge sockets are recommended.

    How to prepare the existing fixture for Dimming Ballasts

    Replace the lamp sockets with Rapid Start sockets

    Use the existing sockets, and the existing wires

    Replace the lamp sockets with Rapid Start sockets

    Use the existing sockets, and the existing wires

    Replace the lamp sockets with Rapid Start sockets

    Use the existing sockets, and the existing wires

    Replace the lamp sockets with Rapid Start socketsNote that (2) 2 lamp ballasts will replace this ballast

    Use the existing sockets, and the existing wiresNote that (2) 2 lamp ballasts will replace this ballast

    Total number of wirescoming out of the ballast

    5 or FEWER

    6 or 7

    7 or FEWER

    8 or 9

    9 or FEWER

    10 or 11

    11 or FEWER

    12 or 13

    • Lamps must be mounted along their entire lengthwithin 1/2 inch (12.7mm) of a grounded metal reflectoror fixture housing.

    • Compact fluorescent lamps must be 4 pin.

    • Ballast cases and fixtures must be earth grounded.

    • Yellow leads from the ballast should run to the lampend closest to the ballast.

    • Ballasts are not designed for remote mounting. Totallength of wire from the ballast to the lamp socket isnot to exceed 7 ft. (2.1m) for T5 HO linear, T8, andT12, and not to exceed 3 ft. (0.9m) for T4 compactand T5 twin tube.

  • 7Step by Step instructions for RadioTouch Controller

    One Lamp

    Two Lamp

    Two Compact Fluorescent Lamp

    Three Lamp

    LAMP

    LAMPBLUEMount to

    GroundedFixture

    RED

    YELLOW

    BLUE

    LAMP

    LAMP

    LAMPMount toGrounded

    Fixture

    BLUE/WHITE

    BLUEBLUE

    REDREDYELLOWYELLOW

    Mount toGrounded

    Fixture

    Step 5: Check for proper socket wiring

    Wrong - wired in series.Correct - wired in parallel.

    Yellow (or Blue with WhiteStripe) wires

    RED

    LutronDimming Ballast

    BLUE

    Mount toGrounded

    Fixture

    LAMP

    Hardware InstallationBallast Wiring

    Step 4: Ballast and fixture wiringPlease ensure that your ballast lamp wires are asfollows: Note: Wire colors shown are

    for Lutron dimming ballastsonly.

    Note: For 4 lamp fixtures,please see the ReferenceSection, page 54 for wiringdetails.

    YELLOW

    RED

    LutronDimming Ballast

    LutronDimming Ballast

    LutronDimming Ballast

  • 8 Step by Step instructions for RadioTouch Controller

    Step 6: Determining a mountinglocation for the RadioTouchController

    The RadioTouch Controller is mounted onto a 4" x 4"standard (1900) junction box (not included, but available- Lutron Part Number 241-496) or to the standard knock-out on the end of a fluorescent lighting fixture. TheRadioTouch Controller must be mounted within 35 feetof all transmitters in the system.

    All power wire connections will be made in the 4" x 4"junction box or the fluorescent lighting fixture. All Class2 wire connections must be made within the front coverof the RadioTouch Controller.

    Caution - Observe all local and nationalelectrical codes and Safety Standards.

    Hardware InstallationMounting Location

    7.8"(150mm)

    2.5" (64mm)5"(130mm)

    Note: The RadioTouch Controller can be mounted inany position.

    TabletopTransmitter

    WallboxTransmitter

    35 ft.

    All Transmitters MUST bewithin 35 ft. of the Controller.

    Controller

    WALL

    CEILING

    Note: If possible, it is recommended to mountall the RadioTouch Controllers in the roomtogether. This will simplify programming andsetup.

  • 9Step by Step instructions for RadioTouch Controller

    Sivoia C

    ntrl 1

    Sivoia C

    ntrl 2

    RTA

    -RX

    -F-S

    CR

    adio

    Freq

    uen

    cyC

    on

    troller

    LIS

    TE

    D 243C

    Ind

    . Co

    nt. E

    q.

    Co

    op

    ersbu

    rg, PA

    18036S

    TA

    TU

    S IN

    DIC

    AT

    OR

    OP

    ER

    AT

    ION

    ON

    - Bu

    rn-in

    Mo

    de

    Slo

    w B

    link -N

    orm

    al O

    pera

    tion

    Mo

    de

    Fast B

    link - P

    rog

    ram

    Very

    Fast B

    link - R

    eceiv

    ing

    RF

    Data

    Rad

    ioTo

    uch

    12

    34

    56

    78

    910

    1112

    1314

    1516

    Occ. Co

    mmon

    Signal

    15V

    24V

    Circuit C

    om

    Sw Clo

    sure 1

    Sw Clo

    sure 2

    Sw Clo

    sure 3

    Sw Clo

    sure 4

    Sw Clo

    sure 5

    Closur

    e Com

    0-10 Pu

    rple

    0-10-Gra

    y

    Settin

    gs

    Cla

    ss 2 w

    iring co

    nnectio

    ns sh

    own a

    bove.

    TM

    Occ. S

    ensor

    0-1

    0 V

    Shade

    Sw

    itch C

    losure

    s

    12

    34

    5 Po

    were

    dW

    hen

    Lit

    Sta

    tus

    Ind

    icato

    rP

    rog

    ram

    Bu

    tton

    Bu

    rn-in

    Bu

    tton

    RE

    CE

    IVE

    R S

    WIT

    CH

    SE

    TT

    ING

    S1. U

    P-P

    reset L

    ock

    DN

    .-Pre

    set A

    dj.

    2. U

    P-O

    cc. S

    ensor

    DN

    .-Em

    erg

    . Set.

    3. U

    P-F

    DB

    Mode

    DN

    .-EC

    O M

    ode

    4. U

    P-O

    FF

    DN

    .-Min

    . Lig

    ht

    5. U

    P-A

    uto

    ON

    DN

    .-Manual O

    N

    See In

    sta

    llers

    Guid

    e fo

    rS

    yste

    m A

    ddre

    ssin

    g a

    nd

    Pro

    gra

    mm

    ing In

    stru

    ctio

    ns

    Junction Box Mounting

    Fixture Mounting

    Chase nipple (included)

    Hardware InstallationMounting Location

    Siv

    oia

    Cnt

    rl 1

    Siv

    oia

    Cnt

    rl 2

    RTA-RX

    -F-SC

    Radio F

    requen

    cy Cont

    roller

    LISTED

    243C

    Ind. Co

    nt. Eq.

    Cooper

    sburg,

    PA 180

    36STA

    TUS IND

    ICATOR

    OPERA

    TION

    ON - B

    urn-in M

    ode

    Slow B

    link -No

    rmal Op

    eration

    Mode

    Fast Bl

    ink - Pr

    ogram

    Mode

    Very Fa

    st Blink

    - Rece

    iving R

    F DataRad

    ioTouch

    12 3

    45

    67

    89 1

    0 11 1

    2 13 1

    4 15 1

    6

    Occ

    . Com

    Sig

    nal 15V 24

    V

    Cir

    cuit

    Com Sw

    Clo

    sure

    1

    Sw

    Clo

    sure

    2

    Sw

    Clo

    sure

    3

    Sw

    Clo

    sure

    4

    Sw

    Clo

    sure

    5

    Clo

    sure

    Com

    0-10

    Pur

    ple

    0-10

    Gra

    y

    Receive

    r

    Setting

    s

    Term

    inal

    con

    nect

    ions

    are

    Cla

    ss 2

    .

    TM

    Occ. Se

    nsor

    0-10 V

    Shade

    Switch

    Closure

    s

    1 23 4

    5

    Powere

    d

    When L

    it

    Status

    Indicat

    orPro

    gram

    Button

    Burn-in

    ButtonREC

    EIVER

    SWITC

    H SETT

    INGS

    1. UP-P

    reset Lo

    ckDN

    .-Prese

    t Adj.

    2. UP-O

    cc. Sen

    sorDN

    .-Emerg

    . Set.

    3. UP-F

    DB Mod

    eDN

    .-ECO M

    ode

    4. UP-O

    FF

    DN.-M

    in. Light

    5. UP-A

    uto ON

    DN.-M

    anual O

    N

    See Ins

    tallers G

    uide for

    System

    Address

    ing and

    Progra

    mming

    Instruct

    ions

    ®

    1 23

    Shade

    Setting

    s

    SHADE

    SWITC

    H SETT

    INGS

    1. UP-A

    /C Shad

    esDN

    .-Norma

    l Oper.

    PS

    Sig

    nal

    © 2

    000-

    2002

    Lut

    ron

    Ele

    ctro

    nics

    Co.

    , Inc

    .

    Front Cover

    Class 2Wiring Input

    4" x 4"Junction

    Box

  • 10 Step by Step instructions for RadioTouch Controller

    Why wire in bypass?This is a TEMPORARY WIRING SCHEME to test theballast wiring without a control. If there is a wiring prob-lem or a short in the circuit, this will prevent damage tothe RadioTouch Controller. Make the appropriate wireconnections for your ballast type using the wiring dia-grams below.

    Step 7: Wiring in BypassWire your system in bypass as follows:

    Hi-lume® FDB or Eco-10TM Ballast

    Lutron 0-10 Volt Ballast

    Hardware InstallationBallast Wiring Pre-test

    ?

    Danger - Locate and lock the supply breakerin the OFF position, or remove the supply fusebefore continuing.

    Note: Lamp wires not shown,but must be in place and correctfor bypass testing.

    Danger - Proper short circuit and overloadprotection must be provided at the distributionpanel. You can use up to a 20A maximumcircuit breaker for your installation.

    Danger - Proper short circuit and overloadprotection must be provided at the distributionpanel. You can use up to a 20A maximumcircuit breaker for your installation.

    Note: Lamp wires not shown,but must be in place and correctfor bypass testing.

    Distribution Panel

    GroundNeutralHot

    GroundNeutralSwitched HotDimmed Hot

    BypassConnections

    Grounds

    Neutrals

    HotDimmed Hot

    Switched Hot

    4" x 4" Junctionbox or first fixturein the circuit for

    mountingRadioTouchController

    GreenWhiteBlackOrange

    GreenWhiteBlackOrange

    Fixture Ground

    Lutron FDB or ECODimming Ballast

    To Additional DimmingBallasts

    Fixture Ground

    Lutron FDB or ECODimming Ballast

    Distribution Panel

    GroundNeutralHot

    GroundNeutralSwitched Hot

    BypassConnections

    Grounds

    Neutrals

    Hot Switched Hot4" x 4" Junctionbox or first fixturein the circuit for

    mountingRadioTouchController

    GreenWhiteBlack

    Fixture Ground

    Lutron 0-10VDimming Ballast

    To Additional DimmingBallasts

    Fixture Ground

    Lutron 0-10VDimming Ballast

    GrayPurple

    GreenWhiteBlack

    GrayPurple

    GrayPurple

    Class 2 Wiring

  • 11Step by Step instructions for RadioTouch Controller

    Siv

    oia

    Cnt

    rl 1

    Siv

    oia

    Cnt

    rl 2

    RTA-RX

    -F-SC

    Radio F

    requen

    cy Cont

    roller

    LISTED

    243C

    Ind. Co

    nt. Eq.

    Cooper

    sburg,

    PA 180

    36STA

    TUS IND

    ICATOR

    OPERA

    TION

    ON - B

    urn-in M

    ode

    Slow B

    link -No

    rmal Op

    eration

    Mode

    Fast Bl

    ink - Pr

    ogram

    Mode

    Very Fa

    st Blink

    - Rece

    iving R

    F DataRad

    ioTouch

    12 3

    45

    67

    89 1

    0 11 1

    2 13 1

    4 15 1

    6

    Occ

    . Com

    Sig

    nal 15V 24

    V

    Cir

    cuit

    Com Sw

    Clo

    sure

    1

    Sw

    Clo

    sure

    2

    Sw

    Clo

    sure

    3

    Sw

    Clo

    sure

    4

    Sw

    Clo

    sure

    5

    Clo

    sure

    Com

    0-10

    Pur

    ple

    0-10

    Gra

    y

    Receive

    r

    Setting

    s

    Term

    inal

    con

    nect

    ions

    are

    Cla

    ss 2

    .

    TM

    Occ. Se

    nsor

    0-10 V

    Shade

    Switch

    Closure

    s

    1 23 4

    5

    Powere

    d

    When L

    it

    Status

    Indicat

    orPro

    gram

    Button

    Burn-in

    ButtonREC

    EIVER

    SWITC

    H SETT

    INGS

    1. UP-P

    reset Lo

    ckDN

    .-Prese

    t Adj.

    2. UP-O

    cc. Sen

    sorDN

    .-Emerg

    . Set.

    3. UP-F

    DB Mod

    eDN

    .-ECO M

    ode

    4. UP-O

    FF

    DN.-M

    in. Light

    5. UP-A

    uto ON

    DN.-M

    anual O

    N

    See Ins

    tallers G

    uide for

    System

    Address

    ing and

    Progra

    mming

    Instruct

    ions

    ®

    1 23

    Shade

    Setting

    s

    SHADE

    SWITC

    H SETT

    INGS

    1. UP-A

    /C Shad

    esDN

    .-Norma

    l Oper.

    PS

    Sig

    nal

    © 2

    000-

    2002

    Lut

    ron

    Ele

    ctro

    nics

    Co.

    , Inc

    .

    1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

    CLASS 2 LOW VOLTAGE WIRING

    1 2 3 4 5 Power Status Program Burn-In1 2 3

    Hi-lume® or Eco-10TM Ballast and Control Wiring

    Step 8: Testing the circuitTurn the input power ON after assuring that it is safe todo so.

    Danger - Check that all loads on the circuit aresafe to have power applied before turning theinput power ON.

    Once the wiring is tested, turn the input power backOFF at the supply breaker.

    Danger - Locate and lock the supply breakerin the OFF position, or remove the supply fusebefore continuing.

    Lights should go to Full ON while in bypass.

    Step 9A: Wiring the RadioTouchController for each zone oflighting

    Turn Power OFF.

    Danger - Locate and lock the supply breakerin the OFF position, or remove the supply fusebefore continuing.

    The RadioTouch Controller accepts 120V or 277V linefeeds. Controller wiring depends on the input voltage(see diagram below). The electronic fluorescentballasts, however, must be rated for the specific linevoltage that feeds the Controller.

    Remove the bypass wiring connections previously made.

    Connect the input feed wires and the output load wiresto the RadioTouch Controller as indicated in the wiringdiagram below and on the following page.

    Hardware InstallationBallast Wiring Pre-test

    Note: Lamp wires not shown,but must be in place and correctfor proper operation.

    Siv

    oia

    Cn

    trl 1

    Siv

    oia

    Cn

    trl 2

    RTA-RX-F-SCRadio Frequency Controller

    LISTED 243CInd. Cont. Eq.

    Coopersburg, PA 18036

    STATUS INDICATOR OPERATIONON - Burn-in ModeSlow Blink -Normal Operation ModeFast Blink - Program ModeVery Fast Blink - Receiving RF Data

    RadioTouch

    1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

    Occ

    . Co

    m

    Sig

    nal

    15V

    24V

    Cir

    cuit

    Co

    m

    Sw

    Clo

    sure

    1

    Sw

    Clo

    sure

    2

    Sw

    Clo

    sure

    3

    Sw

    Clo

    sure

    4

    Sw

    Clo

    sure

    5

    Clo

    sure

    Co

    m

    0-10

    Pu

    rple

    0-10

    Gra

    y

    ReceiverSettings

    Term

    inal

    co

    nn

    ecti

    on

    sar

    e C

    lass

    2.

    TM

    Occ. Sensor 0-10 V Shade Switch Closures

    1 2 3 4 5

    PoweredWhen Lit

    StatusIndicator

    ProgramButton

    Burn-inButton

    RECEIVER SWITCH SETTINGS1. UP-Preset Lock DN.-Preset Adj.2. UP-Occ. Sensor DN.-Emerg. Set.3. UP-FDB Mode DN.-ECO Mode4. UP-OFF DN.-Min. Light5. UP-Auto ON DN.-Manual ON

    See Installers Guide for SystemAddressing and Programming Instructions

    ®

    1 2 3

    ShadeSettings

    SHADE SWITCH SETTINGS1. UP-A/C Shades DN.-Normal Oper.

    PS

    Sig

    nal

    © 2

    000-

    2002

    Lut

    ron

    Ele

    ctro

    nics

    Co.

    , Inc

    .

    Distribution Panel

    GroundNeutralHot

    Green (Ground)White (Neutral)Blue (Switched Hot)Orange (Dimmed Hot)

    GreenWhiteBlack (120V)Blue

    GreenWhiteBlackOrange

    GreenWhiteBlackOrange

    Fixture Ground

    Lutron FDB or ECODimming Ballast

    Fixture Ground

    Lutron FDB or ECODimming Ballast

    To Additional DimmingBallasts

    Red (277V)Cap the wire thatis not being used(Red or Blackdepending oninput voltage)

  • 12 Step by Step instructions for RadioTouch Controller

    Hardware InstallationWiring the Controller

    Lutron 0-10 Volt Ballast and Control Wiring

    1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

    CLASS 2 LOW VOLTAGE WIRING

    1 2 3 4 5 Power Status Program Burn-In1 2 3

    Note: Lamp wires not shown,but must be in place and correctfor proper operation.

    Danger - Locate and lock the supply breakerin the OFF position, or remove the supply fusebefore working on any circuit.

    Siv

    oia

    Cn

    trl 1

    Siv

    oia

    Cn

    trl 2

    RTA-RX-F-SCRadio Frequency Controller

    LISTED 243CInd. Cont. Eq.

    Coopersburg, PA 18036

    STATUS INDICATOR OPERATIONON - Burn-in ModeSlow Blink -Normal Operation ModeFast Blink - Program ModeVery Fast Blink - Receiving RF Data

    RadioTouch

    1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

    Occ

    . Co

    m

    Sig

    nal

    15V

    24V

    Cir

    cuit

    Co

    m

    Sw

    Clo

    sure

    1

    Sw

    Clo

    sure

    2

    Sw

    Clo

    sure

    3

    Sw

    Clo

    sure

    4

    Sw

    Clo

    sure

    5

    Clo

    sure

    Co

    m

    0-10

    Pu

    rple

    0-10

    Gra

    y

    ReceiverSettings

    Term

    inal

    co

    nn

    ecti

    on

    sar

    e C

    lass

    2.

    TM

    Occ. Sensor 0-10 V Shade Switch Closures

    1 2 3 4 5

    PoweredWhen Lit

    StatusIndicator

    ProgramButton

    Burn-inButton

    RECEIVER SWITCH SETTINGS1. UP-Preset Lock DN.-Preset Adj.2. UP-Occ. Sensor DN.-Emerg. Set.3. UP-FDB Mode DN.-ECO Mode4. UP-OFF DN.-Min. Light5. UP-Auto ON DN.-Manual ON

    See Installers Guide for SystemAddressing and Programming Instructions

    ®

    1 2 3

    ShadeSettings

    SHADE SWITCH SETTINGS1. UP-A/C Shades DN.-Normal Oper.

    PS

    Sig

    nal

    © 2

    000-

    2002

    Lut

    ron

    Ele

    ctro

    nics

    Co.

    , Inc

    .

    Distribution Panel

    GroundNeutralHot

    Green (Ground)White (Neutral)Blue (Switched Hot)Orange (Cap off)

    GreenWhiteBlack

    Fixture Ground

    Lutron 0-10VDimming Ballast

    Fixture Ground

    Lutron 0-10VDimming Ballast

    GrayPurple

    GreenWhiteBlack

    GrayPurple– Gray

    + PurpleClass 2 Wiring

    GreenWhiteBlack (120V)Blue

    To Additional DimmingBallasts

    Red (277V)

    Cap the wire thatis not being used(Red or Blackdepending oninput voltage)

    Important Capacity Note: Do not connect more than40, 0-10 Volt ballasts to a single RadioTouch Controller.

  • 13Step by Step instructions for RadioTouch Controller

    Step 9B: Wiring the RadioTouchControllers for multiplelighting zones

    Turn Power OFF.

    Danger - Locate and lock the supply breakerin the OFF position, or remove the supply fusebefore continuing.

    The RadioTouch Controller accepts 120V or 277V linefeeds. The Electronic Fluorescent Ballasts, however,must be rated for the specific line voltage that feedsthe Controller.

    Remove the bypass wiring connections previously made.

    Connect the input feed wires and the output load wiresto the RadioTouch Controller as indicated in the wiringdiagram below and on the following page.

    Hi-lume® or Eco-10TM Ballast and Control Wiring for multiple zones of light

    1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

    CLASS 2 LOW VOLTAGE WIRING

    1 2 3 4 5 Power Status Program Burn-In

    1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

    CLASS 2 LOW VOLTAGE WIRING

    1 2 3 4 5 Power Status Program Burn-In

    1 2 3

    1 2 3

    Hardware InstallationWiring the Controller

    Note: Lamp wires not shown, butmust be in place and correct forproper operation.

    Note: Lamp wires not shown,but must be in place and correctfor proper operation.

    Siv

    oia

    Cn

    trl 1

    Siv

    oia

    Cn

    trl 2

    RTA-RX-F-SCRadio Frequency Controller

    LISTED 243CInd. Cont. Eq.

    Coopersburg, PA 18036

    STATUS INDICATOR OPERATIONON - Burn-in ModeSlow Blink -Normal Operation ModeFast Blink - Program ModeVery Fast Blink - Receiving RF Data

    RadioTouch

    1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

    Occ

    . Co

    m

    Sig

    nal

    15V

    24V

    Cir

    cuit

    Co

    m

    Sw

    Clo

    sure

    1

    Sw

    Clo

    sure

    2

    Sw

    Clo

    sure

    3

    Sw

    Clo

    sure

    4

    Sw

    Clo

    sure

    5

    Clo

    sure

    Co

    m

    0-10

    Pu

    rple

    0-10

    Gra

    y

    ReceiverSettings

    Term

    inal

    co

    nn

    ecti

    on

    sar

    e C

    lass

    2.

    TM

    Occ. Sensor 0-10 V Shade Switch Closures

    1 2 3 4 5

    PoweredWhen Lit

    StatusIndicator

    ProgramButton

    Burn-inButton

    RECEIVER SWITCH SETTINGS1. UP-Preset Lock DN.-Preset Adj.2. UP-Occ. Sensor DN.-Emerg. Set.3. UP-FDB Mode DN.-ECO Mode4. UP-OFF DN.-Min. Light5. UP-Auto ON DN.-Manual ON

    See Installers Guide for SystemAddressing and Programming Instructions

    ®

    1 2 3

    ShadeSettings

    SHADE SWITCH SETTINGS1. UP-A/C Shades DN.-Normal Oper.

    PS

    Sig

    nal

    © 2

    000-

    2002

    Lut

    ron

    Ele

    ctro

    nics

    Co.

    , Inc

    .

    Siv

    oia

    Cn

    trl 1

    Siv

    oia

    Cn

    trl 2

    RTA-RX-F-SCRadio Frequency Controller

    LISTED 243CInd. Cont. Eq.

    Coopersburg, PA 18036

    STATUS INDICATOR OPERATIONON - Burn-in ModeSlow Blink -Normal Operation ModeFast Blink - Program ModeVery Fast Blink - Receiving RF Data

    RadioTouch

    1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

    Occ

    . Co

    m

    Sig

    nal

    15V

    24V

    Cir

    cuit

    Co

    m

    Sw

    Clo

    sure

    1

    Sw

    Clo

    sure

    2

    Sw

    Clo

    sure

    3

    Sw

    Clo

    sure

    4

    Sw

    Clo

    sure

    5

    Clo

    sure

    Co

    m

    0-10

    Pu

    rple

    0-10

    Gra

    y

    ReceiverSettings

    Term

    inal

    co

    nn

    ecti

    on

    sar

    e C

    lass

    2.

    TM

    Occ. Sensor 0-10 V Shade Switch Closures

    1 2 3 4 5

    PoweredWhen Lit

    StatusIndicator

    ProgramButton

    Burn-inButton

    RECEIVER SWITCH SETTINGS1. UP-Preset Lock DN.-Preset Adj.2. UP-Occ. Sensor DN.-Emerg. Set.3. UP-FDB Mode DN.-ECO Mode4. UP-OFF DN.-Min. Light5. UP-Auto ON DN.-Manual ON

    See Installers Guide for SystemAddressing and Programming Instructions

    ®

    1 2 3

    ShadeSettings

    SHADE SWITCH SETTINGS1. UP-A/C Shades DN.-Normal Oper.

    PS

    Sig

    nal

    © 2

    000-

    2002

    Lut

    ron

    Ele

    ctro

    nics

    Co.

    , Inc

    .

    Distribution Panel

    GroundNeutralHot

    Green (Ground)White (Neutral)Blue (Switched Hot)Orange (Dimmed Hot)

    GreenWhiteBlack (120V)Blue

    Red * (277V)

    GroundNeutralHot

    Green (Ground)White (Neutral)Blue (Switched Hot)Orange (Dimmed Hot)

    GreenWhiteBlack (120V)Blue

    GreenWhiteBlackOrange

    Fixture Ground

    Lutron FDB or ECODimming Ballast

    To Additional DimmingBallasts

    GreenWhiteBlackOrange

    Fixture Ground

    Lutron FDB or ECODimming Ballast

    GreenWhiteBlackOrange

    Fixture Ground

    Lutron FDB or ECODimming Ballast

    GreenWhiteBlackOrange

    Fixture Ground

    Lutron FDB or ECODimming Ballast

    To Additional DimmingBallasts

    To AdditionalLighting Zones

    * Cap the wire that is not beingused (Red or Black depending oninput voltage)

    Red * (277V)

    * Cap the wire that is not beingused (Red or Black depending oninput voltage)

    Siv

    oia

    Cnt

    rl 1

    Siv

    oia

    Cnt

    rl 2

    RTA-RX

    -F-SC

    Radio F

    requen

    cy Cont

    roller

    LISTED

    243C

    Ind. Co

    nt. Eq.

    Cooper

    sburg,

    PA 180

    36STA

    TUS IND

    ICATOR

    OPERA

    TION

    ON - B

    urn-in M

    ode

    Slow B

    link -No

    rmal Op

    eration

    Mode

    Fast Bl

    ink - Pr

    ogram

    Mode

    Very Fa

    st Blink

    - Rece

    iving R

    F DataRad

    ioTouch

    12 3

    45

    67

    89 1

    0 11 1

    2 13 1

    4 15 1

    6

    Occ

    . Com

    Sig

    nal 15V 24

    V

    Cir

    cuit

    Com Sw

    Clo

    sure

    1

    Sw

    Clo

    sure

    2

    Sw

    Clo

    sure

    3

    Sw

    Clo

    sure

    4

    Sw

    Clo

    sure

    5

    Clo

    sure

    Com

    0-10

    Pur

    ple

    0-10

    Gra

    y

    Receive

    r

    Setting

    s

    Term

    inal

    con

    nect

    ions

    are

    Cla

    ss 2

    .

    TM

    Occ. Se

    nsor

    0-10 V

    Shade

    Switch

    Closure

    s

    1 23 4

    5

    Powere

    d

    When L

    it

    Status

    Indicat

    orPro

    gram

    Button

    Burn-in

    ButtonREC

    EIVER

    SWITC

    H SETT

    INGS

    1. UP-P

    reset Lo

    ckDN

    .-Prese

    t Adj.

    2. UP-O

    cc. Sen

    sorDN

    .-Emerg

    . Set.

    3. UP-F

    DB Mod

    eDN

    .-ECO M

    ode

    4. UP-O

    FF

    DN.-M

    in. Light

    5. UP-A

    uto ON

    DN.-M

    anual O

    N

    See Ins

    tallers G

    uide for

    System

    Address

    ing and

    Progra

    mming

    Instruct

    ions

    ®

    1 23

    Shade

    Setting

    s

    SHADE

    SWITC

    H SETT

    INGS

    1. UP-A

    /C Shad

    esDN

    .-Norma

    l Oper.

    PS

    Sig

    nal

    © 2

    000-

    2002

    Lut

    ron

    Ele

    ctro

    nics

    Co.

    , Inc

    .

  • 14 Step by Step instructions for RadioTouch Controller

    Wiring for Switching Loads

    Step 10: Wiring the RadioTouchSwitchpack Controller foreach zone

    Turn Power OFF.

    Danger - Locate and lock the supply breakerin the OFF position, or remove the supply fusebefore continuing.

    The RadioTouch Switchpack Controller accepts 120V or277V line feeds. Controller wiring depends on the inputvoltage (see diagram below). The load circuit, however,must be rated for the specific line voltage that feeds theController.

    Remove the bypass wiring connections previously made.

    Connect the input feed wires and the output load wiresto the RadioTouch Switchpack Controller as indicated inthe wiring diagram below.

    Incandescent(16 Amps)

    Fluorescent Electronic Ballast orFluorescent Magnetic Ballast(16 Amps)

    MagneticLow Voltage(16 Amps)

    ElectronicLow Voltage(16 Amps)

    Neon/ColdCathode(16 Amps)

    Motor Loads(1/3HP @120V,1/2HP @ 277V)

    HID(16 Amps)

    Switched Loads Include:

    Hardware InstallationWiring the Controller

    Siv

    oia

    Cnt

    rl 1

    Siv

    oia

    Cnt

    rl 2

    RTA-RX

    -F-SC

    Radio F

    requen

    cy Cont

    roller

    LISTED

    243C

    Ind. Co

    nt. Eq.

    Cooper

    sburg,

    PA 180

    36STA

    TUS IND

    ICATOR

    OPERA

    TION

    ON - B

    urn-in M

    ode

    Slow B

    link -No

    rmal Op

    eration

    Mode

    Fast Bl

    ink - Pr

    ogram

    Mode

    Very Fa

    st Blink

    - Rece

    iving R

    F DataRad

    ioTouch

    12 3

    45

    67

    89 1

    0 11 1

    2 13 1

    4 15 1

    6

    Occ

    . Com

    Sig

    nal 15V 24

    V

    Cir

    cuit

    Com Sw

    Clo

    sure

    1

    Sw

    Clo

    sure

    2

    Sw

    Clo

    sure

    3

    Sw

    Clo

    sure

    4

    Sw

    Clo

    sure

    5

    Clo

    sure

    Com

    0-10

    Pur

    ple

    0-10

    Gra

    y

    Receive

    r

    Setting

    s

    Term

    inal

    con

    nect

    ions

    are

    Cla

    ss 2

    .

    TM

    Occ. Se

    nsor

    0-10 V

    Shade

    Switch

    Closure

    s

    1 23 4

    5

    Powere

    d

    When L

    it

    Status

    Indicat

    orPro

    gram

    Button

    Burn-in

    ButtonREC

    EIVER

    SWITC

    H SETT

    INGS

    1. UP-P

    reset Lo

    ckDN

    .-Prese

    t Adj.

    2. UP-O

    cc. Sen

    sorDN

    .-Emerg

    . Set.

    3. UP-F

    DB Mod

    eDN

    .-ECO M

    ode

    4. UP-O

    FF

    DN.-M

    in. Light

    5. UP-A

    uto ON

    DN.-M

    anual O

    N

    See Ins

    tallers G

    uide for

    System

    Address

    ing and

    Progra

    mming

    Instruct

    ions

    ®

    1 23

    Shade

    Setting

    s

    SHADE

    SWITC

    H SETT

    INGS

    1. UP-A

    /C Shad

    esDN

    .-Norma

    l Oper.

    PS

    Sig

    nal

    © 2

    000-

    2002

    Lut

    ron

    Ele

    ctro

    nics

    Co.

    , Inc

    .

    1 2 3 4 5 6 7 8CLASS 2 LOW VOLTAGE WIRING

    1 2 3 Power Status Program Burn-In

    Distribution Panel

    GroundNeutralHot

    Green (Ground)White (Neutral)Blue (Switched Hot)

    GreenWhiteBlack (120V)Blue

    GreenWhiteBlack

    GreenWhiteBlack

    Fixture Ground

    Switched Load

    Fixture Ground

    Switched Load

    To AdditionalSwitched Loads

    Red (277V)Cap the wire thatis not being used(Red or Blackdepending oninput voltage)

    RTA-RX-SWRadio Frequency Controller

    LISTED 243CInd. Cont. Eq.

    Coopersburg, PA 18036

    RadioTouchTM

    ®

    1 2 3

    1 2 3 4 5 6 7 8

    Occ

    . Co

    m

    Sig

    nal

    15V

    24V

    Cir

    cuit

    Co

    m

    Occ. Sensor

    STATUS INDICATOR OPERATIONON - Burn-in ModeSlow Blink -Normal Operation ModeFast Blink - Program ModeVery Fast Blink - Receiving RF Data

    RECEIVER SWITCH SETTINGS1. UP-Preset Lock DN.-Preset Adj.2. UP-Occ. Sensor DN.-Emerg. Set.3. UP-Auto ON DN.-Manual ON

    ReceiverSettings

    PoweredWhen Lit

    StatusIndicator

    ProgramButton

    See Installers Guide forSystem Addressing andProgramming Instructions

    Term

    inal

    co

    nn

    ecti

    on

    sar

    e C

    lass

    2.

    © 2

    000-

    2002

    Lut

    ron

    Ele

    ctro

    nics

    Co.

    , Inc

    .

  • 15Step by Step instructions for RadioTouch Controller

    Why wire in bypass?This is a TEMPORARY WIRING SCHEME to test the wiring without a control. If there is a wiring problemor a short in the circuit, this will prevent damage to the RadioTouch Controller. Make the appropriate wireconnections for your load type using the above wiring diagrams.

    Step 11A:Wiring the RadioTouchController in Bypass whenusing Load Interfaces

    Lutron Tu-Wire® Dimming Ballast Interface

    Incandescent / Magnetic Low Voltage Interface and Electronic Low-Voltage Interface

    Hardware InstallationInterface Wiring

    ?

    Danger - Locate and lock the supply breakerin the OFF position, or remove the supply fusebefore continuing.

    Note: Lamp wires notshown, but must be in placeand correct for bypasstesting.

    Danger - Proper short circuit and overloadprotection must be provided at the distributionpanel. You can use up to a 20A maximumcircuit breaker for your installation.

    Danger - Proper short circuit and overloadprotection must be provided at the distributionpanel. You can use up to a 20A maximumcircuit breaker for your installation.

    The FDI-FTU-16A-120, FDI-ELV-1000 andthe FDI-INC-2000 operate on 120 volts only.

    Fixture Ground

    Fixture Ground

    Distribution Panel

    GroundNeutralHot (120V)

    GroundNeutralDimmed Hot

    Green

    White

    Black

    Green

    White

    Black

    To AdditionalLight Fixtures

    4" x 4" Junction box or 2 gangwallbox for mounting

    Incandescent / Magnetic Low-Voltage Interface or Electronic

    Low-Voltage Interface

    Neutrals

    Grounds

    Hot Dimmed Hot

    ControllerJunction Box

    Fixture Ground

    Fixture Ground

    Distribution Panel

    GroundNeutralHot (120V)

    GroundNeutralDimmed Hot

    GreenWhite

    Black

    GreenWhite

    Black

    To AdditionalDimming Ballasts

    4" x 4" Junction box or 2gang wallbox for mountingTu-Wire® Ballast Interface

    Neutrals

    Grounds

    Hot Dimmed Hot

    ControllerJunction Box

    Tu-Wire®DimmingBallast

    Tu-Wire®DimmingBallast

  • 16 Step by Step instructions for RadioTouch Controller

    DO

    NO

    T W

    IRE

    LIV

    E!

    UP UP

    CO

    OP

    ER

    SB

    UR

    G, P

    A U

    SA

    1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

    CLASS 2 LOW VOLTAGE WIRING

    1 2 3 4 5 Power Status Program Burn-In1 2 3

    DO

    NO

    T W

    IRE

    LIV

    E!

    UP UP

    CO

    OP

    ER

    SB

    UR

    G, P

    A U

    SA

    1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

    CLASS 2 LOW VOLTAGE WIRING

    1 2 3 4 5 Power Status Program Burn-In1 2 3

    Siv

    oia

    Cn

    trl 1

    Siv

    oia

    Cn

    trl 2

    RTA-RX-F-SCRadio Frequency Controller

    LISTED 243CInd. Cont. Eq.

    Coopersburg, PA 18036

    STATUS INDICATOR OPERATIONON - Burn-in ModeSlow Blink -Normal Operation ModeFast Blink - Program ModeVery Fast Blink - Receiving RF Data

    RadioTouch

    1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

    Occ

    . Co

    m

    Sig

    nal

    15V

    24V

    Cir

    cuit

    Co

    m

    Sw

    Clo

    sure

    1

    Sw

    Clo

    sure

    2

    Sw

    Clo

    sure

    3

    Sw

    Clo

    sure

    4

    Sw

    Clo

    sure

    5

    Clo

    sure

    Co

    m

    0-10

    Pu

    rple

    0-10

    Gra

    y

    ReceiverSettings

    Term

    inal

    co

    nn

    ecti

    on

    sar

    e C

    lass

    2.

    TM

    Occ. Sensor 0-10 V Shade Switch Closures

    1 2 3 4 5

    PoweredWhen Lit

    StatusIndicator

    ProgramButton

    Burn-inButton

    RECEIVER SWITCH SETTINGS1. UP-Preset Lock DN.-Preset Adj.2. UP-Occ. Sensor DN.-Emerg. Set.3. UP-FDB Mode DN.-ECO Mode4. UP-OFF DN.-Min. Light5. UP-Auto ON DN.-Manual ON

    See Installers Guide for SystemAddressing and Programming Instructions

    ®

    1 2 3

    ShadeSettings

    SHADE SWITCH SETTINGS1. UP-A/C Shades DN.-Normal Oper.

    PS

    Sig

    nal

    © 2

    000-

    2002

    Lut

    ron

    Ele

    ctro

    nics

    Co.

    , Inc

    .

    Distribution Panel

    GroundNeutralHot (120V)

    GroundNeutralHotOrange(Control Input)

    To AdditionalLight Fixtures

    Neutral

    DimmedHot Output

    Blue(Cap off)

    Red (277V)Cap off theRed wire

    GreenWhiteBlack (120V)Blue

    FDI-INC-2000Incandescent /

    Magnetic Low-VoltageInterface

    ORFDI-ELV-1000

    Electronic Low-VoltageInterface

    Load and Control Wiring Using the Incandescent / Magnetic Low-Voltage Interface (FDI–INC-2000) or Electronic Low-Voltage Interface (FDI-ELV-1000)

    Hardware InstallationWiring the Interface

    Step 11B: Wiring the RadioTouchController using LoadInterfaces

    Turn Power OFF.

    Danger - Locate and lock the supply breakerin the OFF position, or remove the supply fusebefore continuing.

    The FDI-FTU-16A-120, FDI-ELV-1000 andthe FDI-INC-2000 operate on 120 volts only.

    Ballast and Control Wiring Using the Tu-Wire® Interface (FDI-FTU-16A-120)

    When using Load Interfaces, it may be necessary toadjust the preset light levels prior to use. (See AdjustPreset Light Levels on pages 58 through 60 aftercompleting wiring.)

    Remove the bypass wiring connections previouslymade.

    Connect the input feed wires and the output load wiresas indicated by the wiring diagrams below.

    Note: Lamp wires notshown, but must be in placeand correct for properoperation.

    Siv

    oia

    Cn

    trl 1

    Siv

    oia

    Cn

    trl 2

    RTA-RX-F-SCRadio Frequency Controller

    LISTED 243CInd. Cont. Eq.

    Coopersburg, PA 18036

    STATUS INDICATOR OPERATIONON - Burn-in ModeSlow Blink -Normal Operation ModeFast Blink - Program ModeVery Fast Blink - Receiving RF Data

    RadioTouch

    1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

    Occ

    . Co

    m

    Sig

    nal

    15V

    24V

    Cir

    cuit

    Co

    m

    Sw

    Clo

    sure

    1

    Sw

    Clo

    sure

    2

    Sw

    Clo

    sure

    3

    Sw

    Clo

    sure

    4

    Sw

    Clo

    sure

    5

    Clo

    sure

    Co

    m

    0-10

    Pu

    rple

    0-10

    Gra

    y

    ReceiverSettings

    Term

    inal

    co

    nn

    ecti

    on

    sar

    e C

    lass

    2.

    TM

    Occ. Sensor 0-10 V Shade Switch Closures

    1 2 3 4 5

    PoweredWhen Lit

    StatusIndicator

    ProgramButton

    Burn-inButton

    RECEIVER SWITCH SETTINGS1. UP-Preset Lock DN.-Preset Adj.2. UP-Occ. Sensor DN.-Emerg. Set.3. UP-FDB Mode DN.-ECO Mode4. UP-OFF DN.-Min. Light5. UP-Auto ON DN.-Manual ON

    See Installers Guide for SystemAddressing and Programming Instructions

    ®

    1 2 3

    ShadeSettings

    SHADE SWITCH SETTINGS1. UP-A/C Shades DN.-Normal Oper.

    PS

    Sig

    nal

    © 2

    000-

    2002

    Lut

    ron

    Ele

    ctro

    nics

    Co.

    , Inc

    .

    Fixture Ground

    Fixture Ground

    Distribution Panel

    GroundNeutralHot (120V)

    GroundNeutralHotOrange(Control Input)

    To AdditionalLight Fixtures

    Neutral

    DimmedHot Output

    Blue(Cap off)

    Red (277V)Cap off theRed wire

    GreenWhiteBlack (120V)Blue

    FDI-FTU-16A-120Tu-Wire® Ballast

    Interface

    Fixture Ground

    Fixture Ground

    Tu-Wire®DimmingBallast

    Tu-Wire®DimmingBallast

  • 17Step by Step instructions for RadioTouch Controller

    Step 12: Mounting the RadioTouchController

    Using the two screws for the junction box cover, attachthe RadioTouch Controller to the junction box or closefixture ballast cover.

    Caution - Be sure all the power wires arecompletely inside the junction box or fixturebefore tightening the mounting screws orclosing the fixture.

    Siv

    oia

    Cn

    trl 1

    Siv

    oia

    Cn

    trl 2

    RTA-RX

    -F-SC

    Radio F

    requen

    cy

    Control

    ler

    LISTED

    243C

    Ind. Co

    nt. Eq.

    Cooper

    sburg,

    PA 180

    36 STATU

    S IND

    ICATO

    R OPE

    RATIO

    N

    ON - B

    urn-in

    Mode

    Slow B

    link -N

    ormal O

    peratio

    n Mod

    e

    Fast B

    link - P

    rogram

    Very

    Fast B

    link - R

    eceivin

    g RF D

    ataRadio

    Touch

    12 3

    45

    67

    89 1

    0 11 1

    2 13 1

    4 15 1

    6

    Occ.

    Co

    mm

    on

    Sig

    nal

    15V 24V

    Cir

    cu

    it C

    om

    Sw

    Clo

    su

    re 1

    Sw

    Clo

    su

    re 2

    Sw

    Clo

    su

    re 3

    Sw

    Clo

    su

    re 4

    Sw

    Clo

    su

    re 5

    Clo

    su

    re C

    om

    0-1

    0 P

    urp

    le

    0-1

    0-G

    ray

    Settin

    gs

    Class 2

    wiring

    connec

    tions sh

    own abo

    ve.

    TM

    Occ. S

    ensor

    0-10 V

    Shade

    Switch

    Closu

    res

    1 23 4

    5

    Powe

    red

    When

    Lit

    Status

    Indica

    tor

    Progra

    m

    Butto

    n

    Burn-

    in

    Butto

    n

    RECE

    IVER S

    WITC

    H SET

    TINGS

    1. UP-P

    reset L

    ock

    DN.-P

    reset A

    dj.

    2. UP-O

    cc. Se

    nsor

    DN.-E

    merg.

    Set.

    3. UP-F

    DB Mo

    de

    DN.-E

    CO Mo

    de

    4. UP-O

    FF

    DN.-M

    in. Lig

    ht

    5. UP-A

    uto ON

    DN.-M

    anual O

    N

    See In

    staller

    s Guid

    e for

    System

    Addre

    ssing

    and

    Progra

    mming

    Instruc

    tions

    Sivoia C

    ntrl 1

    Sivoia C

    ntrl 2

    RTA

    -RX

    -F-S

    CR

    adio

    Freq

    uen

    cyC

    on

    troller

    LIS

    TE

    D 243C

    Ind

    . Co

    nt. E

    q.

    Co

    op

    ersbu

    rg, PA

    18036S

    TA

    TU

    S IN

    DIC

    AT

    OR

    OP

    ER

    AT

    ION

    ON

    - Bu

    rn-in

    Mo

    de

    Slo

    w B

    link -N

    orm

    al O

    pera

    tion

    Mo

    de

    Fast B

    link - P

    rog

    ram

    Very

    Fast B

    link - R

    eceiv

    ing

    RF

    Data

    Rad

    ioTo

    uch

    12

    34

    56

    78

    910

    1112

    1314

    1516

    Occ. Co

    mmon

    Signal

    15V

    24V

    Circuit C

    om

    Sw Clo

    sure 1

    Sw Clo

    sure 2

    Sw Clo

    sure 3

    Sw Clo

    sure 4

    Sw Clo

    sure 5

    Closur

    e Com

    0-10 Pu

    rple

    0-10-Gra

    y

    Settin

    gs

    Cla

    ss 2 w

    iring co

    nnectio

    ns sh

    own a

    bove.

    TM

    Occ. S

    en

    so

    r0-1

    0 V

    Shade

    Sw

    itch

    Clo

    su

    res

    12

    34

    5 Po

    were

    dW

    hen

    Lit

    Sta

    tus

    Ind

    icato

    rP

    rog

    ram

    Bu

    tton

    Bu

    rn-in

    Bu

    tton

    RE

    CE

    IVE

    R S

    WIT

    CH

    SE

    TT

    ING

    S1. U

    P-P

    rese

    t Lock

    DN

    .-Pre

    set A

    dj.

    2. U

    P-O

    cc. S

    enso

    rD

    N.-E

    merg

    . Set.

    3. U

    P-F

    DB

    Mode

    DN

    .-EC

    O M

    ode

    4. U

    P-O

    FF

    DN

    .-Min

    . Lig

    ht

    5. U

    P-A

    uto

    ON

    DN

    .-Man

    ual O

    N

    See In

    sta

    llers

    Guid

    e fo

    rS

    yste

    m A

    ddre

    ssin

    g a

    nd

    Pro

    gra

    mm

    ing In

    stru

    ctio

    ns

    For best performance do not position the receiverantenna parallel and in close proximity to another metalsurface (such as a fluorescent lighting fixture or thereceiver itself). The antenna should be at approximately a45° angle from these types of surfaces.

    RadioTouch AntennaPositioning

    Hardware InstallationWiring the Controller

    Antenna at a45° angle Fluorescent lighting fixture

    Step 11C: Mounting the LoadInterface

    The Load Interface mounts into a 4 in. x 4 in. junctionbox with a minimum depth of 3 in. The Interfaces canalso be mounted in a 2-gang wallbox with a minimumdepth of 3 in. Note: The Load Interface must only bemounted into a metal junction box that is properlygrounded.

    Caution - Be sure all the power wires arecompletely inside the junction box beforetightening the mounting screws.

  • 18 Step by Step instructions for RadioTouch Controller

    Step 14: Wallbox Transmitter wiringNote: The RadioTouch Wallbox Transmitters may re-place any existing wall switch. The Wallbox Transmittersdo not switch line voltage. They transmit RF signals tothe Controller, which dims the lighting, turns the zoneON or OFF, and sends signals to other equipment, suchas Sivoia® shades.

    Hardware InstallationWallbox Transmitters

    Turn the input power ON after assuring that it is safe todo so.

    Danger - Check that all loads on the circuit aresafe to have power applied before turning theinput power ON.

    Once the wiring is tested, turn the input power backOFF at the supply breaker.

    Danger - Locate and lock the supply breaker inthe OFF position, or remove the supply fusebefore continuing.

    Lights should go to Full ON. To test dimming circuits,press the program button on the Controller and thelights should cycle from high to low end settling at 50%light. (To test switching circuits, press the programbutton on the Switchpack Controller and the lightsshould cycle ON and OFF). Press the program buttonagain to remove it from this mode.

    Step 13: Testing the RadioTouchController

    Neutral White

    Hot Black

    Distribution Panel

    Ground(120 or 277 Volts)

    Single or Multi-location control of a single zone:Model Function

    Single or Multi-location control of one or more zones:Model Function Model Function

    RTA-WX-C2LBEquipment controlled bymomentary dry contact closureoutputs

    UP

    DOWN

    RTA-WX-C2SBEquipment controlled bymomentary dry contactclosure outputs

    OPEN

    STOP

    CLOSE

    RTA-WX-C3LBEquipment controlled bymomentary dry contact closureoutputs

    Equipment controlled bymomentary dry contact closureoutputs

    RTA-WX-C3SB

    RTA-WX-S5SB Sivoia® shades with presets

    ON

    OFF RTA-WX-2BSW ON/OFF switched lighting

    ON

    OFF RTA-WX-2B Dimmable lighting

    Dimmable lighting with presetsRTA-WX-5B

    RTA-WX-S2LB Sivoia® shadesOPEN

    CLOSE

    ON/OFF switched lightingRTA-WX-SW

    Dimmable lightingRTA-WX-1B

  • 19Step by Step instructions for RadioTouch Controller

    Hardware InstallationWallbox Transmitters

    Step 15: Mounting the WallboxTransmitters

    Mount the Wallbox Transmitters using the suppliedscrews.

    Note: If the RTA-WX-1B or RTA-WX-SW control isbeing mounted next to other controls, break off the sidesections of the wallbox transmitter and of the adjoiningcontrols to allow them to fit. This will not affect the ratingof the RadioTouch Control. See instructions of othercontrols to determine if they need to be derated whenganging.

    Install the Claro® wallplate (sold separately).

    Turn ON the power after wiring is complete.

    Step 16: Addressing the WallboxTransmitter to theController

    Wallbox Transmitters must be addressed to theController(s) that they are intended to control. One Con-troller can be controlled by up to 16 Transmitters of anytype for multi-location control applications.

    RTA-WX-5B and RTA-WX-S5SBStep A - Press and release the programming button onthe Controller. After the button is pressed the lights willcycle up and down for 3 seconds to notify you that youare in programming mode, and settle at 50% lightoutput. If you are using an RTA-RX-SW the lights willcycle OFF and ON. The Status LED will be in fast blinkmode. If no lights are being controlled by the receiver,you will not get visual feedback.

    Step B - While in programming mode press the top 2buttons on the Wallbox Transmitter that you want tocontrol the Controller and hold for 5 seconds. The Con-troller will flash or cycle the lights OFF and ON if theController is connected to a lighting load. If no lights arebeing controlled by the receiver, you will not get visualfeedback.

    Step C - Press the programming button again to exitfrom programming mode. The lights will go to high endand the Status LED will return to slow blink mode. If youare using an RTA-RX-SW the lights will cycle OFF andON. To test the Wallbox Transmitter for lights, press thegray button and the lights should go OFF. Press anywhite button to turn the lights back ON. For Sivoia®shades, press any button and see that the shadesmove. If no response return to Step A and be sure tohold the buttons for 5 seconds while in Step B.

    Step D - Repeat steps A – C for any other Controllersthat should be controlled by this Wallbox Transmitter.

    Press and hold these twobuttons for 5 seconds

    Step A & C Step B

    1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

    CLASS 2 LOW VOLTAGE WIRING

    1 2 3 4 5 Power Status Program Burn-In1 2 3

    Programming button

    Siv

    oia

    Cn

    trl 1

    Siv

    oia

    Cn

    trl 2

    RTA-RX-F-SCRadio Frequency Controller

    LISTED 243CInd. Cont. Eq.

    Coopersburg, PA 18036

    STATUS INDICATOR OPERATIONON - Burn-in ModeSlow Blink -Normal Operation ModeFast Blink - Program ModeVery Fast Blink - Receiving RF Data

    RadioTouch

    1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

    Occ

    . Co

    m

    Sig

    nal

    15V

    24V

    Cir

    cuit

    Co

    m

    Sw

    Clo

    sure

    1

    Sw

    Clo

    sure

    2

    Sw

    Clo

    sure

    3

    Sw

    Clo

    sure

    4

    Sw

    Clo

    sure

    5

    Clo

    sure

    Co

    m

    0-10

    Pu

    rple

    0-10

    Gra

    y

    ReceiverSettings

    Term

    inal

    co

    nn

    ecti

    on

    sar

    e C

    lass

    2.

    TM

    Occ. Sensor 0-10 V Shade Switch Closures

    1 2 3 4 5

    PoweredWhen Lit

    StatusIndicator

    ProgramButton

    Burn-inButton

    RECEIVER SWITCH SETTINGS1. UP-Preset Lock DN.-Preset Adj.2. UP-Occ. Sensor DN.-Emerg. Set.3. UP-FDB Mode DN.-ECO Mode4. UP-OFF DN.-Min. Light5. UP-Auto ON DN.-Manual ON

    See Installers Guide for SystemAddressing and Programming Instructions

    ®

    1 2 3

    ShadeSettings

    SHADE SWITCH SETTINGS1. UP-A/C Shades DN.-Normal Oper.

    PS

    Sig

    nal

    © 2

    000-

    2002

    Lut

    ron

    Ele

    ctro

    nics

    Co.

    , Inc

    .

    Status LED

  • 20 Step by Step instructions for RadioTouch Controller

    1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

    CLASS 2 LOW VOLTAGE WIRING

    1 2 3 4 5 Power Status Program Burn-In1 2 3

    Siv

    oia

    Cn

    trl 1

    Siv

    oia

    Cn

    trl 2

    RTA-RX-F-SCRadio Frequency Controller

    LISTED 243CInd. Cont. Eq.

    Coopersburg, PA 18036

    STATUS INDICATOR OPERATIONON - Burn-in ModeSlow Blink -Normal Operation ModeFast Blink - Program ModeVery Fast Blink - Receiving RF Data

    RadioTouch

    1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

    Occ

    . Co

    m

    Sig

    nal

    15V

    24V

    Cir

    cuit

    Co

    m

    Sw

    Clo

    sure

    1

    Sw

    Clo

    sure

    2

    Sw

    Clo

    sure

    3

    Sw

    Clo

    sure

    4

    Sw

    Clo

    sure

    5

    Clo

    sure

    Co

    m

    0-10

    Pu

    rple

    0-10

    Gra

    y

    ReceiverSettings

    Term

    inal

    co

    nn

    ecti

    on

    sar

    e C

    lass

    2.

    TM

    Occ. Sensor 0-10 V Shade Switch Closures

    1 2 3 4 5

    PoweredWhen Lit

    StatusIndicator

    ProgramButton

    Burn-inButton

    RECEIVER SWITCH SETTINGS1. UP-Preset Lock DN.-Preset Adj.2. UP-Occ. Sensor DN.-Emerg. Set.3. UP-FDB Mode DN.-ECO Mode4. UP-OFF DN.-Min. Light5. UP-Auto ON DN.-Manual ON

    See Installers Guide for SystemAddressing and Programming Instructions

    ®

    1 2 3

    ShadeSettings

    SHADE SWITCH SETTINGS1. UP-A/C Shades DN.-Normal Oper.

    PS

    Sig

    nal

    © 2

    000-

    2002

    Lut

    ron

    Ele

    ctro

    nics

    Co.

    , Inc

    .

    Hardware InstallationWallbox Transmitters

    Step A - Press and release the programming button onthe Controller. After the button is pressed the lights willcycle up and down for 3 seconds to notify you that youare in programming mode, and settle at 50% lightoutput. The Status LED will be in fast blink mode.

    Step B - While in programming mode press and holdthe large center button on the Wallbox Transmitter for 5seconds. When the Controller has added the walltransmitter, the lights will flash or cycle OFF and ON.

    Step C - Press the programming button again to exitfrom programming mode. The lights will go to high endand the Status LED will return to slow blink mode. Totest the Wallbox Transmitter press the large centerbutton and the lights should go OFF Press it again andthe lights should go back ON. If no response return toStep A and be sure to hold the button for 5 secondswhile in Step B.

    Step D - Repeat steps A – C for any other Controllersthat should be controlled by this Wallbox Transmitter.

    Press and hold thisbutton for 5 seconds

    Step A & C Step B

    Programming button

    Status LED

    Step A - Press and release the programming button onthe Controller. After the button is pressed the lights willcycle up and down for 3 seconds to notify you that youare in programming mode, and settle at 50% lightoutput. If you are using an RTA-RX-SW the lights willcycle OFF and ON. The Status LED will be in fast blinkmode. If no lights are being controlled by this Controller,you will not get visual feedback.

    Step B - While in programming mode press the topbutton on the Wallbox Transmitter and hold it for 5 sec-onds. When the Controller has added the walltransmitter, the lights will flash or cycle OFF and ON, ifthe Controller is connected to a lighting load.

    Step C - Press the programming button again to exitfrom programming mode. The lights will go to high endand the Status LED will return to slow blink mode. If youare using an RTA-RX-SW the lights will cycle OFF andON.

    Step D - Repeat steps A – C for any other Controllersthat should be controlled by this Wallbox Transmitter.

    Step A & C Step B

    ON

    OFF

    Press and holdtop button for 5seconds

    RTA-WX-1B and RTA-WX-SW

    1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

    CLASS 2 LOW VOLTAGE WIRING

    1 2 3 4 5 Power Status Program Burn-In1 2 3

    Programming button

    Siv

    oia

    Cn

    trl 1

    Siv

    oia

    Cn

    trl 2

    RTA-RX-F-SCRadio Frequency Controller

    LISTED 243CInd. Cont. Eq.

    Coopersburg, PA 18036

    STATUS INDICATOR OPERATIONON - Burn-in ModeSlow Blink -Normal Operation ModeFast Blink - Program ModeVery Fast Blink - Receiving RF Data

    RadioTouch

    1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

    Occ

    . Co

    m

    Sig

    nal

    15V

    24V

    Cir

    cuit

    Co

    m

    Sw

    Clo

    sure

    1

    Sw

    Clo

    sure

    2

    Sw

    Clo

    sure

    3

    Sw

    Clo

    sure

    4

    Sw

    Clo

    sure

    5

    Clo

    sure

    Co

    m

    0-10

    Pu

    rple

    0-10

    Gra

    y

    ReceiverSettings

    Term

    inal

    co

    nn

    ecti

    on

    sar

    e C

    lass

    2.

    TM

    Occ. Sensor 0-10 V Shade Switch Closures

    1 2 3 4 5

    PoweredWhen Lit

    StatusIndicator

    ProgramButton

    Burn-inButton

    RECEIVER SWITCH SETTINGS1. UP-Preset Lock DN.-Preset Adj.2. UP-Occ. Sensor DN.-Emerg. Set.3. UP-FDB Mode DN.-ECO Mode4. UP-OFF DN.-Min. Light5. UP-Auto ON DN.-Manual ON

    See Installers Guide for SystemAddressing and Programming Instructions

    ®

    1 2 3

    ShadeSettings

    SHADE SWITCH SETTINGS1. UP-A/C Shades DN.-Normal Oper.

    PS

    Sig

    nal

    © 2

    000-

    2002

    Lut

    ron

    Ele

    ctro

    nics

    Co.

    , Inc

    .

    Status LED

    RTA-WX-2B RTA-WX-C3LBRTA-WX-2BSW RTA-WX-C3SBRTA-WX-C2LB RTA-WX-S2LBRTA-WX-C2SB

  • 21Step by Step instructions for RadioTouch Controller

    Check the Mounting Location:The occupant sensor location is important because itinfluences the operating range of the sensor. For peakperformance, install as follows:

    • Give the sensor an unobstructed view of the room.• The sensor cannot detect motion behind glass or

    walls (including partitions).• Partitions reduce the maximum room dimensions.• Keep the sensor away from the direct flow of air from

    ventilation outlets, windows, or fans.• Place the sensor on the same wall as the doorway so

    that traffic in a hallway will not be picked up asmotion in the room.

    Note: To cover a larger area, 2 occupant sensors canbe wired in parallel (see Step 18 on page 22).

    Hardware InstallationOccupant Sensor

    Step 17: Installing OccupantSensors

    Occupant sensors are motion sensors that send asignal to the RadioTouch Controller. The RadioTouchController can turn the lights ON when motion isdetected and OFF or to a minimum light level whenmotion is not detected.

    Doorway Occupant Sensor

  • 22 Step by Step instructions for RadioTouch Controller

    Step 18: Wiring the OccupantSensor

    Make sure that the supply breaker to the RadioTouchController is OFF.

    Connect the three conductors to the three occupantsensor wires as shown below.

    Connect the appropriate wires to the RadioTouchController terminals 1, 2, and 3 or 4.

    Caution - Observe all local and nationalelectrical codes and Safety Standards.

    Note: The total current drawn for connected occupantsensors must not exceed 30mA. An auxiliary powersupply must be used if this rating is exceeded. Seewiring diagram below.

    Hardware InstallationOccupant Sensor

    One 24 Volt Sensor wired to one ControllerOne 15 Volt Sensor wired to one Controller

    1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16CLASS 2 LOW VOLTAGE WIRING

    1 2 3 4 5 Power Status Program Burn-In

    Blue(Signal)

    Black(OS Common)

    Red(15V)3

    2

    1

    1(OS Common)2 (Signal)3 (15V)

    1 2 3

    1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16CLASS 2 LOW VOLTAGE WIRING

    1 2 3 4 5 Power Status Program Burn-In

    Blue(Signal)

    Black(OS Common)

    Red(24V)4

    2

    1

    1(OS Common)2 (Signal)

    4 (24V)

    1 2 3

    Siv

    oia

    Cn

    trl 1

    Siv

    oia

    Cn

    trl 2

    RTA-RX-F-SCRadio Frequency Controller

    LISTED 243CInd. Cont. Eq.

    Coopersburg, PA 18036

    STATUS INDICATOR OPERATIONON - Burn-in ModeSlow Blink -Normal Operation ModeFast Blink - Program ModeVery Fast Blink - Receiving RF Data

    RadioTouch

    1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

    Occ

    . Co

    m

    Sig

    nal

    15V

    24V

    Cir

    cuit

    Co

    m

    Sw

    Clo

    sure

    1

    Sw

    Clo

    sure

    2

    Sw

    Clo

    sure

    3

    Sw

    Clo

    sure

    4

    Sw

    Clo

    sure

    5

    Clo

    sure

    Co

    m

    0-10

    Pu

    rple

    0-10

    Gra

    y

    ReceiverSettings

    Term

    inal

    co

    nn

    ecti

    on

    sar

    e C

    lass

    2.

    TM

    Occ. Sensor 0-10 V Shade Switch Closures

    1 2 3 4 5

    PoweredWhen Lit

    StatusIndicator

    ProgramButton

    Burn-inButton

    RECEIVER SWITCH SETTINGS1. UP-Preset Lock DN.-Preset Adj.2. UP-Occ. Sensor DN.-Emerg. Set.3. UP-FDB Mode DN.-ECO Mode4. UP-OFF DN.-Min. Light5. UP-Auto ON DN.-Manual ON

    See Installers Guide for SystemAddressing and Programming Instructions

    ®

    1 2 3

    ShadeSettings

    SHADE SWITCH SETTINGS1. UP-A/C Shades DN.-Normal Oper.

    PS

    Sig

    nal

    © 2

    000-

    2002

    Lut

    ron

    Ele

    ctro

    nics

    Co.

    , Inc

    .

    Siv

    oia

    Cn

    trl 1

    Siv

    oia

    Cn

    trl 2

    RTA-RX-F-SCRadio Frequency Controller

    LISTED 243CInd. Cont. Eq.

    Coopersburg, PA 18036

    STATUS INDICATOR OPERATIONON - Burn-in ModeSlow Blink -Normal Operation ModeFast Blink - Program ModeVery Fast Blink - Receiving RF Data

    RadioTouch

    1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

    Occ

    . Co

    m

    Sig

    nal

    15V

    24V

    Cir

    cuit

    Co

    m

    Sw

    Clo

    sure

    1

    Sw

    Clo

    sure

    2

    Sw

    Clo

    sure

    3

    Sw

    Clo

    sure

    4

    Sw

    Clo

    sure

    5

    Clo

    sure

    Co

    m

    0-10

    Pu

    rple

    0-10

    Gra

    y

    ReceiverSettings

    Term

    inal

    co

    nn

    ecti

    on

    sar

    e C

    lass

    2.

    TM

    Occ. Sensor 0-10 V Shade Switch Closures

    1 2 3 4 5

    PoweredWhen Lit

    StatusIndicator

    ProgramButton

    Burn-inButton

    RECEIVER SWITCH SETTINGS1. UP-Preset Lock DN.-Preset Adj.2. UP-Occ. Sensor DN.-Emerg. Set.3. UP-FDB Mode DN.-ECO Mode4. UP-OFF DN.-Min. Light5. UP-Auto ON DN.-Manual ON

    See Installers Guide for SystemAddressing and Programming Instructions

    ®

    1 2 3

    ShadeSettings

    SHADE SWITCH SETTINGS1. UP-A/C Shades DN.-Normal Oper.

    PS

    Sig

    nal

    © 2

    000-

    2002

    Lut

    ron

    Ele

    ctro

    nics

    Co.

    , Inc

    .

    One Sensor wired to two or more Controllers (15V Sensor shown)

    1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16CLASS 2 LOW VOLTAGE WIRING

    1 2 3 4 5 Power Status Program Burn-In

    1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16CLASS 2 LOW VOLTAGE WIRING

    1 2 3 4 5 Power Status Program Burn-In

    Blue(Signal)

    Black(OS Common)

    Red(15V)3

    2

    1

    1 (OS Common)

    2 (Signal)

    3 (15V)

    1 (OS Common)

    2 (Signal)

    To additionalRadioTouchControllers

    6 (Circuit Common)6 (Circuit Common)

    To additionalOccupant Sensors

    Additional RadioTouchControllers optional

    1 2 3 1 2 3

    Siv

    oia

    Cn

    trl 1

    Siv

    oia

    Cn

    trl 2

    RTA-RX-F-SCRadio Frequency Controller

    LISTED 243CInd. Cont. Eq.

    Coopersburg, PA 18036

    STATUS INDICATOR OPERATIONON - Burn-in ModeSlow Blink -Normal Operation ModeFast Blink - Program ModeVery Fast Blink - Receiving RF Data

    RadioTouch

    1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

    Occ

    . Co

    m

    Sig

    nal

    15V

    24V

    Cir

    cuit

    Co

    m

    Sw

    Clo

    sure

    1

    Sw

    Clo

    sure

    2

    Sw

    Clo

    sure

    3

    Sw

    Clo

    sure

    4

    Sw

    Clo

    sure

    5

    Clo

    sure

    Co

    m

    0-10

    Pu

    rple

    0-10

    Gra

    y

    ReceiverSettings

    Term

    inal

    co

    nn

    ecti

    on

    sar

    e C

    lass

    2.

    TM

    Occ. Sensor 0-10 V Shade Switch Closures

    1 2 3 4 5

    PoweredWhen Lit

    StatusIndicator

    ProgramButton

    Burn-inButton

    RECEIVER SWITCH SETTINGS1. UP-Preset Lock DN.-Preset Adj.2. UP-Occ. Sensor DN.-Emerg. Set.3. UP-FDB Mode DN.-ECO Mode4. UP-OFF DN.-Min. Light5. UP-Auto ON DN.-Manual ON

    See Installers Guide for SystemAddressing and Programming Instructions

    ®

    1 2 3

    ShadeSettings

    SHADE SWITCH SETTINGS1. UP-A/C Shades DN.-Normal Oper.

    PS

    Sig