TIP122-STMicroelectronics

8/6/2019 TIP122-STMicroelectronics

1/13

November 2008 Rev 4 1/13

13

TIP120, TIP121, TIP122TIP125, TIP126, TIP127

Complementary power Darlington transistors

Features Low collector-emitter saturation voltage Complementary NPN - PNP transistors

Applications

General purpose linear and switching

DescriptionThe devices are manufactured in planartechnology with base island layout andmonolithic Darlington configuration. The resultingtransistors show exceptional high gainperformance coupled with very low saturationvoltage.

Figure 1. Internal schematic diagrams

TO-2201

23

NPN: R 1= 7 K PNP: R 1= 16 K R2= 60 R2= 70

Table 1. Device summary

Order codes Marking Package Packaging

TIP120 TIP120

TO-220 Tube

TIP121 TIP121

TIP122 TIP122

TIP125 TIP125

TIP126 TIP126

TIP127 TIP127

www.st.com
http://www.st.com/http://www.st.com/


2/13

Content TIP120, TIP121, TIP122, TIP125, TIP126, TIP127

2/13

Content

1 Electrical ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2.1 Electrical characteristics (curves) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

3 Test circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

4 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

5 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11


3/13

TIP120, TIP121, TIP122, TIP125, TIP126, TIP127 Electrical ratings

3/13

1 Electrical ratings

Table 2. Absolute maximum rating(1)

1. For PNP types voltage and current values are negative.

Symbol Parameter Value Unit

NPN TIP120 TIP121 TIP122

PNP TIP125 TIP126 TIP127

VCBO Collector-base voltage (I E = 0) 60 80 100 V

VCEO Collector-emitter voltage (I B = 0) 60 80 100 V

VEBO Emitter-base voltage (I C = 0) 5 V

IC Collector current 5 A

ICM Collector peak current 8 AIB Base current 0.12 A

P TOTTotal dissipation at T c 25 C

Tamb 25 C652

W

Tstg Storage temperature -65 to 150C

TJ Max. operating junction temperature 150

Table 3. Thermal data

Symbol Parameter Value Unit

R thj-case Thermal resistance junction-case max. 1.92C/W

R thj-amb Thermal resistance junction-ambient max. 62.5


4/13

Electrical characteristics TIP120, TIP121, TIP122, TIP125, TIP126, TIP127

4/13

2 Electrical characteristics

(Tcase = 25 C ; unless otherwise specified)

Table 4. Electrical characteristics (1)

1. For PNP types voltage and current values are negative.

Symbol Parameter Test conditions Min. Typ. Max. Unit

ICEOCollector cut-off current(IB = 0)

for TIP120/125 V CE = 30 Vfor TIP121/126 V CE = 40 Vfor TIP122/127 V CE = 50 V

0.50.50.5

mAmAmA

ICBOCollector cut-off current(IB = 0)

for TIP120/125 V CE = 60 Vfor TIP121/126 V CE = 80 Vfor TIP122/127 V CE = 100 V

0.20.20.2

mAmAmA

IEBOEmitter cut-off current(IC = 0) VEB = 5 V 2 mA

VCEO(sus)(2)

2. Pulsed duration = 300 s, duty cycle 2%

Collector-emittersustaining voltage(IB = 0)

IC = 30 mAfor TIP120/125for TIP121/126for TIP122/127

6080

100

VVV

VCE(sat)(2) Collector-emitter

saturation voltageIC = 3 A I B = 12 mAIC = 5 A I B = 20 mA

24

VV

VBE(on)(2) Base-emitter on voltage I C = 3 A V CE = 3 V 2.5 V

hFE(2) DC current gain

IC = 0.5 A V CE = 3 VIC = 3 A V CE = 3 V

1000

1000


5/13

TIP120, TIP121, TIP122, TIP125, TIP126, TIP127 Electrical characteristics

5/13

2.1 Electrical characteristics (curves)

Figure 2. Safe operating area Figure 3. Derating curve

Figure 4. DC current gain for NPN type Figure 5. DC current gain for PNP type

Figure 6. Collector-emitter saturation voltagefor NPN type

Figure 7. Collector-emitter saturation voltagefor PNP type

hFE

1000

100

100.01 Ic(A)0.1 1

VCE = 3 V

T j= -40 CT j= 25 CT j=125 C

AM00696v1hFE

1000

100

10-0.01 Ic(A)-0.1 -1

T j= -40 CT j= 25 CT j=125 C

VCE = -3 V

AM00697v1

VCE( sa t)

1

0.6

0.20.1 Ic(A)1

hFE = 250

T j= -40 CT j= 25 CT j=125 C

(V)

1.4

AM0069 8 v1VCE( sa t)

-1

-0.6

-0.2-0.1 Ic(A)-1

hFE = 250

T j= -40 CT j= 25 CT j=125 C

(V)

-1.4

AM00699v1


6/13

Electrical characteristics TIP120, TIP121, TIP122, TIP125, TIP126, TIP127

6/13

Figure 8. Base-emitter saturation voltage forNPN type

Figure 9. Base-emitter saturation voltage forPNP type

Figure 10. Base-emitter on voltage for NPNtype Figure 11. Base-emitter on voltage for PNPtype

Figure 12. Switching time on resistive load forNPN type (on)

Figure 13. Switching time on resistive load forPNP type (on)

VBE( sa t)

1.5

1.0

0.50.1 Ic(A)1

hFE = 250

T j= -40 CT j= 25 CT j=125 C

(V)

2.0

AM00700v1VBE( sa t)

-1.5

-1.0

-0.5-0.1 Ic(A)-1

hFE = 250

T j= -40 CT j= 25 CT j=125 C

(V)

-2.0

AM03 261v1

VBE(on)

1.5

1.0

0.50.1 Ic(A)1

VCE = 3 V

T j= -40 CT j= 25 CT j

=125 C

(V)

2.0

AM03 262v1VBE(on)

-1.5

-1.0

-0.5- 0.1 Ic(A)-1

T j= -40 CT j= 25 CT j

=125 C

(V)

-2.0VCE = -3 V

AM03 26 3 v1

t(n s )

100

100 Ic(A)2

Del a y timeRis e time

1 3 54

Vcc = 30 V

h FE =250Vbeof= - 5 V

Ibon= - Ibof

AM03 264v1t(n s )

100

100 Ic(A)-2

Del a y timeRis e time

-1 -3 -5-4

Vcc = -30 V

h FE =250Vbeof= 5 V

-Ibon= Ibof

AM03 265v1


7/13

TIP120, TIP121, TIP122, TIP125, TIP126, TIP127 Electrical characteristics

7/13

Figure 14. Switching time on resistive load forNPN type (off)

Figure 15. Switching time on resistive load forPNP type (off)

Figure 16. Capacitances for NPN type Figure 17. Capacitances for PNP type

t(n s )

1000

1000 Ic(A)2

S tora ge timeFa ll time

1 3 54

Vcc = 30 V

h FE =250

Vbeof= - 5 V

Ibon= - Ibof

AM03 266v1t(n s )

1000

1000 Ic(A)-2

S tora ge timeFa ll time

-1 -3 -5-4

Vcc

= -30 V

h FE =250

Vbeof= 5 V-Ibon= Ibof

AM03 267v1

C(pF)

100

100.01 VR(V)10.1 10

F= 0.1 MHz

CCB

CEB

AM03 269v1C(pF)

100

100.01 VR(V)10.1 10

F= 0.1 MHz

CCB

C EB

AM03 26 8 v1


8/13

Test circuits TIP120, TIP121, TIP122, TIP125, TIP126, TIP127

8/13

3 Test circuits

Figure 18. Resistive load switching for NPN type

Figure 19. Resistive load switching for PNP type

1) Fast electronic switch2) Non-inductive resistor

1) Fast electronic switch2) Non-inductive resistor


9/13

TIP120, TIP121, TIP122, TIP125, TIP126, TIP127 Package mechanical data

9/13

4 Package mechanical data

In order to meet environmental requirements, ST offers these devices in ECOPACK

packages. These packages have a lead-free second level interconnect . The category ofsecond level interconnect is marked on the package and on the inner box label, incompliance with JEDEC Standard JESD97. The maximum ratings related to solderingconditions are also marked on the inner box label. ECOPACK is an ST trademark.ECOPACK specifications are available at: www.st.com


10/13

Package mechanical data TIP120, TIP121, TIP122, TIP125, TIP126, TIP127

10/13

TO-220 mechanical data

Dimmm inch

Min Typ Max Min Typ Max

A 4.40 4.60 0.17 3 0.1 8 1

b 0.61 0. 88 0.024 0.0 3 4

b 1 1.14 1.70 0.044 0.066

c 0.4 8 0.70 0.01 9 0.027

D 15.25 15.75 0.6 0.62

D1 1.27 0.050

E 10 10.40 0. 393 0.40 9

e 2.40 2.70 0.0 9 4 0.106

e1 4. 9 5 5.15 0.1 9 4 0.202

F 1.2 3 1. 3 2 0.04 8 0.051

H1 6.20 6.60 0.244 0.256

J1 2.40 2.72 0.0 9 4 0.107

L 1 3 14 0.511 0.551

L1 3 .50 3 .93 0.1 3 7 0.154

L20 16.40 0.645

L3 0 2 8 .9 0 1.1 3 7

P 3 .75 3 .8 5 0.147 0.151

Q 2.65 2. 9 5 0.104 0.116


11/13

TIP120, TIP121, TIP122, TIP125, TIP126, TIP127 Package mechanical data

11/13

DIM.mm.

MIN. TYP MAX.A 4.47 4.67b 0.70 0.91

b 1 1.17 1. 3 7

c 0. 3 1 0.5 3

D 14.60 15.70E 9.96 10. 3 6e 2.54

e1 4.9 8 5.0 8 5.1 8

F 1.17 1. 3 7H1 6.10 6. 8 0J1 2.52 2. 8 2

L 12.70 1 3 .8 0

L1 3 .20 3 .96L20 15.21 16.77P 3 .73 3 .94Q 2.59 2. 8 9

TO-220 type E mechanical data

765592 3 _B


12/13

Revision history TIP120, TIP121, TIP122, TIP125, TIP126, TIP127

12/13

5 Revision history

Table 5. Document revision historyDate Revision Changes

21-Jun-2004 3

25-Nov-2008 4 Inserted new Section 2.1: Electrical characteristics (curves)


13/13

TIP120, TIP121, TIP122, TIP125, TIP126, TIP127

13/13

Please Read Carefully:

Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (ST) reserve theright to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at anytime, without notice.

All ST products are sold pursuant to STs terms and conditions of sale.

Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes noliability whatsoever relating to the choice, selection or use of the ST products and services described herein.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of thisdocument refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party productsor services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of suchthird party products or services or any intellectual property contained therein.

UNLESS OTHERWISE SET FORTH IN STS TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIEDWARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIEDWARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWSOF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.

UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOTRECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAININGAPPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVEGRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USERS OWN RISK.

Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately voidany warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, anyliability of ST.

ST and the ST logo are trademarks or registered trademarks of ST in various countries.

Information in this document supersedes and replaces all information previously supplied.

The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.

2008 STMicroelectronics - All rights reserved

STMicroelectronics group of companies

Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America

www.st.com

TIP122-STMicroelectronics

Documents

Transcript of TIP122-STMicroelectronics