Thermostat Basics: Types and Applications
-
Upload
ashley -
Category
Technology
-
view
5.430 -
download
1
description
Transcript of Thermostat Basics: Types and Applications
Learning Center
THERMOSTATS
© Jackson Systems, LLC 2011 Intellectual rights apply
Types and Applications
PRODUCT DEFINITION A THERMOSTAT is a key component of any HVAC
system. It maintains the space temperature by cycling the
heating or cooling equipment on and off to maintain a
desired temperature which is referred to as the thermostat
setpoint.
© Jackson Systems, LLC 2011 Intellectual rights apply
Learning Center
THERMOSTATS
PRODUCT DESCRIPTION Thermostats sense the change in space temperature and
turn the heating equipment on when the temperature drops
below the setpoint and off when the temperature reaches
setpoint. They also turn the cooling equipment on when
the temperature rises above the setpoint and off when the
temperature reaches setpoint.
The majority of thermostats operate on low voltage
(24VAC) control circuits. The source of the 24 VAC is a
transformer located in the heating/cooling equipment.
© Jackson Systems, LLC 2011 Intellectual rights apply
Learning Center
THERMOSTATS
PRODUCT DESCRIPTION Line voltage 120VAC or 277VAC thermostats are also
available.
Modern thermostats are almost exclusively digital.
A digital thermostat uses a simple device called a
thermistor to measure temperature.
A thermistor is a resistor which changes its resistance value
as the temperature changes.
The microprocessor in a digital thermostat can measure the
resistance change and converts the resistance value to an
actual temperature reading.
© Jackson Systems, LLC 2011
Intellectual rights apply
Learning Center
THERMOSTATS
PRODUCT DESCRIPTION Thermostats are categorized by their function and the type
of equipment being controlled.
Thermostats can have two (2) functions:
Programmable
Non-Programmable
© Jackson Systems, LLC 2011 Intellectual rights apply
Learning Center
THERMOSTATS
PRODUCT DESCRIPTION Thermostats can control different types of HVAC
equipment.
Single stage (1 heat / 1 cool)
Multi-stage (2 heat / 2 cool)
Heat pump ( 2 heat / 1 cool)
Heat pump ( 3 heat / 2 cool)
Dual fuel ( 2 heat / 1 cool)
Dual fuel (3 heat / 2 cool)
A “universal thermostat” means that it can be configured
to work with any of the above systems.
© Jackson Systems, LLC 2011 Intellectual rights apply
Learning Center
THERMOSTATS
PRODUCT DESCRIPTION One of the most useful features of a digital thermostat is
programmable settings. In the winter you can program the
thermostat to automatically turn up the heat for an hour in
the morning while you get ready for work, turn down the
heat while away from home, turn up the heat in the
evening and then turn down the heat while you sleep. The
same is true for cooling.
Programmable thermostats save energy by automatically
adjusting the temperature based on a user program.
© Jackson Systems, LLC 2011 Intellectual rights apply
Learning Center
THERMOSTATS
PRODUCT DESCRIPTION Residential thermostats typically have 4 schedules per day
Wake or Morning
Leave or Day
Return or Evening
Sleep or Night
Commercial thermostats typically have 2 schedules per
day
Occupied or Day
Unoccupied or Night
© Jackson Systems, LLC 2011 Intellectual rights apply
Learning Center
THERMOSTATS
PRODUCT DESCRIPTION Thermostats can be hardwired or wireless
A hardwired thermostat requires 18 gauge thermostat wire
running from the thermostat to the HVAC equipment.
A wireless thermostat does not wire directly to the
equipment but rather wirelessly communicates via radio
waves to an equipment interface module (EIM) mounted
near the HVAC equipment. The EIM is then hardwired to
the equipment. A wireless thermostat can be used when it
is difficult or impossible to run wires from the equipment to
the thermostat. Wireless thermostats are almost always
powered by batteries.
© Jackson Systems, LLC 2011 Intellectual rights apply
Learning Center
THERMOSTATS
PRODUCT DESCRIPTION Powering thermostats
The three most common types of thermostats are 24VAC
hardwired, battery powered, and dual powered.
24VAC hardwired stats require constant 24 Volts AC from
the equipment transformer.
Battery powered stats do not require 24VAC to power the
thermostat.
Dual powered stats can be powered by the equipment
transformer or by batteries.
© Jackson Systems, LLC 2011 Intellectual rights apply
Learning Center
THERMOSTATS
ADVANCED INSTALLER SETTINGS Most, if not all, digital thermostats today contain “Advanced
Installer Settings”.
Advanced installer settings are typically accessed only by the
contractor during installation.
Advanced installer settings allow for equipment configuration
and selected user preferences.
Depending on the thermostat manufacturer and model, there
can be dozens of advanced installer setting options. Advanced
installer settings are either set by configurable dip switches or
programmed through the key pad or touchscreen.
© Jackson Systems, LLC 2011 Intellectual rights apply
Learning Center
THERMOSTATS
ADVANCED INSTALLER SETTINGS SYSTEM TYPE
Matches the thermostat to the equipment such as single
stage, multi- stage, or heat pump system.
FAN CONTROL
Allows the equipment to energize the fan or the thermostat
to energize the fan during a call for heat.
SCHEDULE FORMAT
Thermostat can be set up as programmable or non-
programmable.
© Jackson Systems, LLC 2011 Intellectual rights apply
Learning Center
THERMOSTATS
ADVANCED INSTALLER SETTINGS CHANGOVER VALVE
Selects O or B reversing valve for heat pumps.
AUXILIARY HEAT
Selects electric or fossil fuel auxiliary heat for heat pumps.
BACKLIGHT
Selects backlight always on or on after a key is pressed.
MANUAL/AUTO-CHANGOVER
Allows the stat to have both heating and cooling available
(auto changeover) or just heat or cool available (manual).
© Jackson Systems, LLC 2011 Intellectual rights apply
Learning Center
THERMOSTATS
ADVANCED INSTALLER SETTINGS TEMPERATURE DISPLAY
Allows selection of Fahrenheit or Celsius to be displayed.
REMOTE SENSOR
Allows selection of no remote sensor, outdoor sensor, or
indoor sensor.
Some stats allow both an indoor and outdoor sensor.
LOW BALANCE POINT
Allows the heat pump to be locked out on a call for heat
below a certain outside temperature (i.e. 30°F) and only
allow the auxiliary heat to be used.
© Jackson Systems, LLC 2011 Intellectual rights apply
Learning Center
THERMOSTATS
ADVANCED INSTALLER SETTINGS HIGH BALANCE POINT
Allows the auxiliary heat to be locked out above a certain
outside temperature (i.e. 60°F) and only allows the heat
pump to be used.
© Jackson Systems, LLC 2011 Intellectual rights apply
Learning Center
THERMOSTATS
ADVANCED INSTALLER SETTINGS ADAPTIVE RECOVERY
When adaptive recovery is OFF, the thermostat will bring
on the HVAC equipment at the exact time of a scheduled
event.
When adaptive recovery is ON, the thermostat will bring
on the HVAC equipment earlier than the schedule event
time. The thermostat anticipates how long it will take to
reach the next scheduled setpoint based on the temperature
in the space and the rate of recovery of the equipment.
PROGRAM PERIODS
Allows 4 or 2 programs per day.
© Jackson Systems, LLC 2011 Intellectual rights apply
Learning Center
THERMOSTATS
ADVANCED INSTALLER SETTINGS SHORT CYCLE PROTECTION
Allows a time delay (typically 5 minutes) between cooling
calls for conventional equipment and both heating and
cooling calls for heat pumps.
© Jackson Systems, LLC 2011 Intellectual rights apply
Learning Center
THERMOSTATS
ADVANCED INSTALLER SETTINGS HEATING LIMIT
Allows selection of a maximum heating setpoint
adjustment.
COOLING LIMIT
Allows selection of a minimum cooling setpoint
adjustment.
KEYPAD LOCKOUT
Allows the thermostat buttons or touch screen icons to
unlocked or locked to limit user access to certain functions.
© Jackson Systems, LLC 2011
Intellectual rights apply
Learning Center
THERMOSTATS
ADVANCED INSTALLER SETTINGS INTERNAL SENSOR CALIBRATION
Allows calibration of the thermostat temperature sensor.
FAN PURGE
Allows selection (0-5 minutes) of extended fan run time
after a heating or cooling call ends.
STAGE DIFFERENTIAL
Allows selection of the temperature difference above or
below the setpoint before the equipment will be allowed to
run.
Example: 70 degrees heating setpoint with a selected 2
degree differential will allow the heating to come on at 68
degrees.
© Jackson Systems, LLC 2011 Intellectual rights apply
Learning Center
THERMOSTATS
INSTALLATION Typical terminal designations for a thermostat controlling
conventional equipment.
R-Wires to the hot side 24VAC equipment transformer
C-Wires to the common side 24VAC equipment
transformer
W1-Wires to the first stage heating relay
W2-Wires to the second stage heating relay
Y1-Wires to the first stage cooling relay
Y2-Wires to the second stage cooling relay
G-Wires to the fan relay
© Jackson Systems, LLC 2011 Intellectual rights apply
Learning Center
THERMOSTATS
INSTALLATION Typical terminal designations for a thermostat controlling
heat pump equipment.
R-Wires to the hot side 24VAC equipment transformer
C-Wires to the common side 24VAC equipment
transformer
W1-Wires to the auxiliary heat
O/B-Wires to the heat pump reversing valve
Y1-Wires to the first stage compressor
Y2-Wires to the second stage compressor
G-Wires to the fan relay
© Jackson Systems, LLC 2011 Intellectual rights apply
Learning Center
THERMOSTATS
INSTALLATION An important part of thermostat operation is location.
The location should represent the ambient space
temperature.
The stat should be mounted on an interior wall.
The stat should be about five (5) feet up from the floor.
The stat should be out of direct sunlight.
The stat should be mounted in a room that is centrally
located and frequently used.
The thermostat should not be installed in an area where
drafts are present, near the floor, behind doors or on an
exterior wall.
© Jackson Systems, LLC 2011 Intellectual rights apply
Learning Center
THERMOSTATS
SAMPLE TEST Thermostats should be configured to match the . . .
A. Color of the house
B. HVAC equipment
C. Location where it will be installed
D. All of the above
For a conventional thermostat, Y1 is for . . .
A. First stage cool
B. Second stage cool
C. First stage heat
D. Second stage heat
© Jackson Systems, LLC 2011 Intellectual rights apply
Learning Center
THERMOSTATS
SAMPLE TEST For a conventional thermostat, W2 is for . . .
A. First stage cool
B. Second stage cool
C. First stage heat
D. Second stage heat
For a heat pump thermostat, Y1 is for . . .
A. First stage compressor
B. Second stage compressor
C. Fan
D. Auxiliary heat
© Jackson Systems, LLC 2011 Intellectual rights apply
Learning Center
THERMOSTATS
SAMPLE TEST Which of the following is an advanced installer option?
A. Adaptive recovery
B. Low balance point
C. Backlight display
D. All of the above
© Jackson Systems, LLC 2011 Intellectual rights apply
Learning Center
THERMOSTATS
SAMPLE TEST Residential programmable thermostats typically have how
many schedules per day?
A. 1
B. 2
C. 3
D. 4
Commercial programmable thermostats typically have
how many schedules per day?
A. 1
B. 2
C. 3
D. 4
© Jackson Systems, LLC 2011 Intellectual rights apply
Learning Center
THERMOSTATS
THERMOSTAT BASICS
Types and Applications
Learning Center
THERMOSTATS
© Jackson Systems, LLC 2011 Intellectual rights apply
888.652.9663
www.jacksonsystems.com
© Jackson Systems, LLC 2011 Intellectual rights apply