The PROFIBUS and PROFINET Company - Procentec Netilities Quick Start Guide Author Dennis van Booma...
-
Upload
nguyencong -
Category
Documents
-
view
219 -
download
2
Transcript of The PROFIBUS and PROFINET Company - Procentec Netilities Quick Start Guide Author Dennis van Booma...
The PROFIBUS and PROFINET Company
Quick Start Guide Copyright © 2012 PROCENTEC. All rights reservedThe PROFIBUS and PROFINET Company
Netilities ‐ Quick Start Guide
Introduction
Netilities compact and efficient tool to support the user with his PROFINET engineering and troubleshooting tasks It can generate a livePROFINET engineering and troubleshooting tasks. It can generate a live list of the PROFINET/Ethernet network and spot the devices which are in Data Exchange. Statistics provide an overview of the network
di i I ili h d d E h /WLAN h PCcondition. It utilizes the standard Ethernet/WLAN port on the PC or interfaces with a ProfiTap.
Important: due to switch technology, it is not possible to simply plug a cable into a switch and capture all PROFINET messages. A switch resends messages only to the appropriate port to which the receiver is g y pp p pconnected. This means that you will not see all messages if you connect to an empty port. You need to set up a mirror port, or use a ProfiTAPwhich creates a safe ‘mirror port’.which creates a safe mirror port .
Quick Start Guide Copyright © 2012 PROCENTEC. All rights reservedThe PROFIBUS and PROFINET CompanyOctober 2012 2Netilities
Getting started
Please make sure that the switch port to which the PROFINET controller is connected, is mirrored to an empty switch port. Connect the mirror portconnected, is mirrored to an empty switch port. Connect the mirror port to your laptop. If you do not have an empty port available for mirroring, or the switch does not support mirroring, you can use a ProfiTap.
Example of mirroring on a Siemens Scalance X208 switch:
Quick Start Guide Copyright © 2012 PROCENTEC. All rights reservedThe PROFIBUS and PROFINET CompanyOctober 2012 3Netilities
Starting Netilities
If you start Netilities for the first time, it checks to see if the required libraries for WinPcap are installed If these libraries are not present thelibraries for WinPcap are installed. If these libraries are not present, the WinPcap installer will be launched. Follow the installation procedure.
Now you are ready to start NetilitiesNow you are ready to start Netilities. The license for Netilities is included on the USB stick, so you do not need to worry about installing a license first. Simply double‐click the Netilities executable on the Appdongle.executable on the Appdongle.
When Netilities is loaded correctly, click on ‘Interfaces’ in the main menu, then choose ‘Enable
interfaces to open a network card.Then tick the appropriate network interface card that
you wish to use.
Quick Start Guide Copyright © 2012 PROCENTEC. All rights reservedThe PROFIBUS and PROFINET CompanyOctober 2012 4Netilities
The Live ListClick the green binoculars to complete the live list information with IP address, device
name, model, role and ID.
The Live List shows all connected devices. Live List color coding:
Green = Device is in Data ExchangeLight blue = Recently sent a telegramYellow = device is inactive
Quick Start Guide Copyright © 2012 PROCENTEC. All rights reservedThe PROFIBUS and PROFINET CompanyOctober 2012 5Netilities
The Live List (2)Use these buttons to:
Flash the ‘Link’ or ‘Ready’ LED on the deviceFlash the ‘Link’ or ‘Ready’ LED on the deviceBrowse to the webserver of the deviceModify IP address or device nameReset factory defaults of the device
Quick Start Guide Copyright © 2012 PROCENTEC. All rights reservedThe PROFIBUS and PROFINET CompanyOctober 2012 6Netilities
StatisticsStatistics provide a valuable resource for troubleshooting.
Choose a statistic here.
You can also view statistics by MAC address instead of IP address.
If you click on a device in the matrix, Netilities will show
additional device information inStatistics color coding:
additional device information in the Info Panel.
Yellow = device is inactiveLight blue = updated statisticNo background color = unchanged
Tip: the time‐outs for the color changes can be set inOptions – Settings – Statistics
Quick Start Guide Copyright © 2012 PROCENTEC. All rights reservedThe PROFIBUS and PROFINET CompanyOctober 2012 7Netilities
Statistics (2)Use this button to freeze the screen. Updates are not shown until you click
on the button again.
Use these buttons to either:Clear statistics for currently selected deviceCl thi t ti ti f ll d iClear this statistic for all devicesClear all statistics for all devices
Tip: this device has a lower max cycle time input than output. Conclusion: it has
been lost.
Quick Start Guide Copyright © 2012 PROCENTEC. All rights reservedThe PROFIBUS and PROFINET CompanyOctober 2012 8Netilities
Bar graphThe bargraph shows device cycle times in a
graph. It makes interpretation of the statistics easier. The bars can be viewed by
The bar graph shows device cycle times in a graph. It makes interpretation of the
statistics easier. The bars can be viewed by IP or MAC address.
Choose the sorting
IP or MAC address.
method here.The red color indicates that the cycle time has
changed. This can also be seen by the increased height of the bar with dotted line.
Quick Start Guide Copyright © 2012 PROCENTEC. All rights reservedThe PROFIBUS and PROFINET CompanyOctober 2012 9Netilities
SNMP Toolbox: Station interface infoMake an SNMP scan of your network using this button. This may take some time.
Extra information from the device becomes available
after the scan.
When the scan is completedWhen the scan is completed, choose a device.
In this case, a switch is selected. It shows interesting
port statistics.
Click this box to auto‐update the information.
Quick Start Guide Copyright © 2012 PROCENTEC. All rights reservedThe PROFIBUS and PROFINET CompanyOctober 2012 10Netilities
the information.
SNMP Toolbox: Topology detection
When a scan is completed, a topology overview is available
on this tab.on this tab.
Netilities shows to which switch port each device is
connected.
The topology is displayed in a tree. It can be collapsed or expanded using these
buttons.
Quick Start Guide Copyright © 2012 PROCENTEC. All rights reservedThe PROFIBUS and PROFINET CompanyOctober 2012 11Netilities
Other featuresNetilities can import a Wireshark log file. Click on ‘Interfaces – Process
PCAP file…’ and select the .pcap file you wish to import.
Then click ‘Start’Then click Start .
Quick Start Guide Copyright © 2012 PROCENTEC. All rights reservedThe PROFIBUS and PROFINET CompanyOctober 2012 12Netilities
Other featuresNetilities has a tool to conveniently
switch between sets of IP configurations. Click on ‘Interfaces –
IP Configuration’.
Add profiles with different IP ranges to easily switch IP address. When added, select one profile and
click ‘Activate profile’. The pre‐defined IP address is now set!defined IP address is now set!
Quick Start Guide Copyright © 2012 PROCENTEC. All rights reservedThe PROFIBUS and PROFINET CompanyOctober 2012 13Netilities