TH series TH-1.6 series Through hole tap · Jig for removing adsorption film [TH-JIG] (1unit/pack)...
Transcript of TH series TH-1.6 series Through hole tap · Jig for removing adsorption film [TH-JIG] (1unit/pack)...
-242-
For surfacemounting
Ⓡ
4
Through hole tapThrough hole tapTH series TH-1.6 series
THB series THC series
THF series TH-0.8 series
TH-0.6 series
Reducing man-hours A through hole changes
to a screw hole!!A through hole changes to a screw hole!!
Types of the TH series
Structure
TH series mounting work procedures
TH seriesTap hole type
TH-0.8 seriesTH-1.6 series
TH-0.6 seriesTHF series
Spacer typeTHB seriesNon-threaded type
THC seriesNon-threaded type
A through hole changes into a tap hole.
Spacer can befit on the board.
A board can be raised and fit.
Can be tightenedby nuts.
TH series [fitting of the parts from the both sides]
TH series [fitting of parts]
TH-1.6 series [fitting of a panel]
THB series [fitting to a chassis]
Packed by tape-and-reel
Through hole tap product group
TH series
Cream solder
PC board
Copper foil
Apply cream solder on the land of a PC board. Load a part by a mounter.
Reflow. Remove the adsorption film.
Jig for removing the adsorption film
* We can make the product of taping specification without adsorption film. Please contact us.(Note that you need to prepare a special adsorption nozzle.)
Jig for removing adsorption film [TH-JIG] (1unit/pack)●
●
●
●
●
●
●
This jig is used for removing the adsorption films after mounting.Film can be removed by piercing the film with the needle edge and pulling it.Films can be removed consecutively. (Approximately 30 sheets)The films pieced to the needle can be collectively removed by turning the resin part.The time required for removing films can be reduced.Disposing is easy because the films have been collectively removed.Object product: TH-series, SSB series
Material Needle part: stainless steel Resin part: Acetal copolymer
(1) Pierce the needle at the center of a film. (Please put the needle from right above.)(2) Pull to raise the film hooked at the needle edge and remove.(3) Approximately 30 sheets can be removed consecutively.(4) Turn the resin part and push out the films on the needle to collectively remove the films. (Turn the resin part in a counter direction after removing the films to return the resin part to the original position prior to use.)
TH-JIGTH-JIG-1.0
0.80.5
M1.2 or overM1.0
Part number φA24.518.5
L Object tap size
■Example of usage
写真52 写真53
■ Part number
■ How to use
●As the edge is sharp, please handle carefully. It may cause injury or damage to a product.●Do not forcibly apply forces because the needle can be easily bent.●If a hole on the film becomes bigger and the needle cannot hook the film to remove, please use tweezers or other adaptive tool to remove it.●When using with M1.2 or over, please use “TH-JIG”. (“TH-JIG-1.0” is the exclusive jig for M1.0.)●Please note that the specification is subject to changes in order to improve performance.
■ Instructions for use
■ Dimension
M5 P=0.8
M5 P=0.835 35
55
93L
38
7.0φ
7.0φ
1.2φAφ
① ② ③ ④
Turn
-243-
For surfacemounting
-244-
For surfacemounting
+0.1-0
● A through hole changes to a threaded hole (M1.0, M1.2, M1.4, M1.6, M1.7, M2, M2.5, M2.6, or M3).● Taping type has an adsorption film. Please remove by pushing it from the opposite side after reflow.● The jig for removing adsorption films (Part number: TH-JIG) is available.● Material: Brass● Finish: Tin plating over nickel base● Rated current:
TH-0.8-M1.0……10A TH-1.6-M1.7……15ATH-0.8-M1.2……12A TH-1.6-M2………20ATH-0.8-M1.4……12A TH-1.6-M2.5、M2.6…20ATH-1.6-M1.6……15A TH-1.6-M3………30A
● Tightening torqueTH-0.8-M1.0……0.3kgf-cm(2.94N-cm)or lessTH-0.8-M1.2……0.6kgf-cm(5.88N-cm)or lessTH-0.8-M1.4……1.0kgf-cm(9.8N-cm)or lessTH-1.6-M1.6……1.5kgf-cm(14.7N-cm)or lessTH-1.6-M1.7……1.5kgf-cm(14.7N-cm)or lessTH-1.6-M2 …… 1.5kgf-cm(14.7N-cm)or lessTH-1.6-M2.5、M2.6……3kgf-cm(29.4N-cm)or lessTH-1.6-M3 …… 5kgf-cm(49N-cm)or less(X-direction)
3kgf-cm(29.4N-cm)or less(Y-direction)● Adaptive printed board thickness: 1.6t or over (TH-1.6 series), 0.8t or over (TH-0.8 series)(There is no problem if it is used for other board thickness.)
● Recommended metal mask thickness:150 to 200μ
Please put the land on the both sides.
180
Dimension of the reel Dimension of the tape
X-X cross-sectionaldrawing
Y-Y cross-sectionaldrawing
X
X
Y Y
■ Recommended fittingland
Shaded part:Opening
■ Recommended metal mask(Recommended metal mask thickness:150μto200μ)
Part number Eφ FφTH-0.8-M1.0 1.8 3.5TH-0.8-M1.2 2.0 3.5TH-0.8-M1.4 2.2 4.0TH-1.6-M1.6 2.4 4.0TH-1.6-M1.7 2.5 4.0TH-1.6-M2 2.7 5.0TH-1.6-M2.5 3.3 5.5TH-1.6-M2.6 3.3 5.5TH-1.6-M3 3.7 6.0
Through hole tap [TH series]
With the parts attached
With the parts attached
Screw can be inserted both from thepart face side and the soldering faceside.
■ Dimensional drawing
Adsorption film
X-direction
Y-direction
Part number PackageTH-0.8-M1.0TH-0.8-M1.2TH-0.8-M1.4TH-1.6-M1.6TH-1.6-M1.7TH-1.6-M2TH-1.6-M2.5TH-1.6-M2.6TH-1.6-M3
A2.52.52.73.03.04.04.54.55.0
MM1.0 P=0.25M1.2 P=0.25M1.4 P=0.3M1.6 P=0.35M1.7 P=0.35M2 P=0.4M2.5 P=0.45M2.6 P=0.45M3 P=0.5
Reel (1000pcs/reel)
Reel (1000pcs/reel)
Reel (1000pcs/reel)
Reel (900pcs/reel)
Reel (900pcs/reel)
Reel (900pcs/reel)
Reel (900pcs/reel)
Reel (900pcs/reel)
Reel (900pcs/reel)
B1.61.82.02.22.32.53.13.13.5
C0.70.70.71.51.51.51.51.51.5
D0.50.50.70.30.30.30.30.30.3
To order bulk product TH-1.6-M3-B
Adsorption films are not put on the bulk products.* Please use the automatic mounter of automatic recognition type.
Please specify ‒B. (100pcs/pack)~~
■ Dimension of the reel
■ Part number
▲ Use of a through hole tap is limited to a through hole board. (It is impossible to use it for a one-sided board and non through hole board.)
・If it is bigger than the recommended fitting through hole (φE), the torque to the Y-direction (soldering face side) will be decreased. (As the flow ofsoldering to the through hole is reduced)
マックエイトのプリント板用端子マックエイトのプリント板用端子
-245-
● A chip mounter can be used for this spacer.● A spacer can be fit on a PC board just by automatically loading it on the PC board and carrying outreflow.
● It can be fit from the part face, soldering face and both sides.● Tape-and-reel has an adsorption film. Please remove by pushing it from the opposite side afterreflow.
● The jig for removing adsorption films (Part number: TH-JIG) is available.● Material: Brass● Finish: Tin plating over nickel base● Rated current:
TH-1.6-□-M1.4……12ATH-1.6-□-M2 ……20ATH-1.6-□-M2.5 M2.6……20ATH-1.6-□-M3 ……30A
● Tightening torqueTH-1.6-□-M1.4……1.0kgf-cm(9.8N-cm)or lessTH-1.6-□-M2……1.5kgf-cm(14.7N-cm)or lessTH-1.6-□-M2.5 M2.6……3kgf-cm(29.4N-cm)or lessTH-1.6-□-M3……5kgf-cm(49N-cm)or less(X-direction)
3kgf-cm(29.4N-cm)or less(Y-direction)● Adaptive printed board thickness: 1.6t or over(There is no problem if it is used for other board thickness.)
● Please use the automatic mounter of automatic recognition type.
■ To order bulk productTH-1.6-0.5-M2-B
With the adsorption film removed after reflow
スルーホールタップ〔TH-1.6シリーズ〕
■ Example of usage
Condition of fitting the panel to theprinted board
■ Dimension
TH-1.6-2.0-M1.4TH-1.6-2.5-M1.4TH-1.6-3.0-M1.4TH-1.6-3.5-M1.4TH-1.6-4.0-M1.4TH-1.6-4.5-M1.4TH-1.6-5.0-M1.4TH-1.6-0.5-M2TH-1.6-1.0-M2TH-1.6-1.5-M2TH-1.6-2.0-M2TH-1.6-2.5-M2TH-1.6-3.0-M2TH-1.6-3.5-M2TH-1.6-4.0-M2TH-1.6-4.5-M2TH-1.6-5.0-M2TH-1.6-5.5-M2TH-1.6-6.0-M2TH-1.6-6.5-M2TH-1.6-7.0-M2TH-1.6-7.5-M2TH-1.6-8.0-M2TH-1.6-0.5-M2.5TH-1.6-1.0-M2.5TH-1.6-1.5-M2.5TH-1.6-2.0-M2.5TH-1.6-2.5-M2.5TH-1.6-3.0-M2.5TH-1.6-3.5-M2.5TH-1.6-4.0-M2.5TH-1.6-4.5-M2.5TH-1.6-5.0-M2.5TH-1.6-5.5-M2.5TH-1.6-6.0-M2.5TH-1.6-6.5-M2.5TH-1.6-7.0-M2.5TH-1.6-7.5-M2.5TH-1.6-8.0-M2.5TH-1.6-8.5-M2.5TH-1.6-9.0-M2.5TH-1.6-9.5-M2.5TH-1.6-10- M2.5TH-1.6-0.5-M2.6
A
2.72.72.72.72.72.72.74.04.04.04.04.04.04.04.04.04.04.04.04.04.04.04.04.54.54.54.54.54.54.54.54.54.54.54.54.54.54.54.54.54.54.54.54.5
B
2.02.02.02.02.02.02.02.52.52.52.52.52.52.52.52.52.52.52.52.52.52.52.53.13.13.13.13.13.13.13.13.13.13.13.13.13.13.13.13.13.13.13.13.1
H
2.02.53.03.54.04.55.00.51.01.52.02.53.03.54.04.55.05.56.06.57.07.58.00.51.01.52.02.53.03.54.04.55.05.56.06.57.07.58.08.59.09.5100.5
M
1.41.41.41.41.41.41.4M2M2M2M2M2M2M2M2M2M2M2M2M2M2M2M2M2.5M2.5M2.5M2.5M2.5M2.5M2.5M2.5M2.5M2.5M2.5M2.5M2.5M2.5M2.5M2.5M2.5M2.5M2.5M2.5M2.6
500pcs400pcs400pcs350pcs350pcs300pcs300pcs450pcs450pcs450pcs450pcs350pcs350pcs350pcs250pcs250pcs250pcs350pcs350pcs300pcs300pcs300pcs300pcs450pcs450pcs450pcs450pcs350pcs350pcs350pcs250pcs250pcs250pcs350pcs350pcs300pcs300pcs300pcs300pcs250pcs250pcs250pcs250pcs450pcs
TH-1.6-1.0-M2.6TH-1.6-1.5-M2.6TH-1.6-2.0-M2.6TH-1.6-2.5-M2.6TH-1.6-3.0-M2.6TH-1.6-3.5-M2.6TH-1.6-4.0-M2.6TH-1.6-4.5-M2.6TH-1.6-5.0-M2.6TH-1.6-5.5-M2.6TH-1.6-6.0-M2.6TH-1.6-6.5-M2.6TH-1.6-7.0-M2.6TH-1.6-7.5-M2.6TH-1.6-8.0-M2.6TH-1.6-8.5-M2.6TH-1.6-9.0-M2.6TH-1.6-9.5-M2.6TH-1.6-10-M2.6TH-1.6-0.5-M3TH-1.6-1.0-M3TH-1.6-1.5-M3TH-1.6-2.0-M3TH-1.6-2.5-M3TH-1.6-3.0-M3TH-1.6-3.5-M3TH-1.6-4.0-M3TH-1.6-4.5-M3TH-1.6-5.0-M3TH-1.6-5.5-M3TH-1.6-6.0-M3TH-1.6-6.5-M3TH-1.6-7.0-M3TH-1.6-7.5-M3TH-1.6-8.0-M3TH-1.6-8.5-M3TH-1.6-9.0-M3TH-1.6-9.5-M3TH-1.6-10-M3TH-1.6-11-M3TH-1.6-12-M3TH-1.6-13-M3TH-1.6-14-M3TH-1.6-15-M3TH-1.6-16-M3
A
4.54.54.54.54.54.54.54.54.54.54.54.54.54.54.54.54.54.54.55.05.05.05.05.05.05.05.05.05.05.05.05.05.05.05.05.05.05.05.05.05.05.05.05.05.0
B
3.13.13.13.13.13.13.13.13.13.13.13.13.13.13.13.13.13.13.13.53.53.53.53.53.53.53.53.53.53.53.53.53.53.53.53.53.53.53.53.53.53.53.53.53.5
H
1.01.52.02.53.03.54.04.55.05.56.06.57.07.58.08.59.09.5100.51.01.52.02.53.03.54.04.55.05.56.06.57.07.58.08.59.09.510111213141516
M
M2.6M2.6M2.6M2.6M2.6M2.6M2.6M2.6M2.6M2.6M2.6M2.6M2.6M2.6M2.6M2.6M2.6M2.6M2.6M3M3M3M3M3M3M3M3M3M3M3M3M3M3M3M3M3M3M3M3M3M3M3M3M3M3
450pcs450pcs450pcs350pcs350pcs350pcs250pcs250pcs250pcs350pcs350pcs300pcs300pcs300pcs300pcs250pcs250pcs250pcs250pcs450pcs450pcs450pcs450pcs350pcs350pcs350pcs250pcs250pcs250pcs350pcs350pcs300pcs300pcs300pcs300pcs250pcs250pcs250pcs250pcs350pcs350pcs150pcs150pcs150pcs150pcs
Part number Number of taps included in the reel Part number Number of taps
included in the reel
Aφ
Bφ
MAdsorption film
H1.5
■ Condition of fitting to the PC board
H
PC board1.6
X-direction
Y-directionIt does not protrude to thesoldering face side.
~~
Please specify –B.
■ Part number
▲ Use of a through hole tap is limitedto a through hole board. (It isimpossible to use it for a one-sidedboard and non through hole board.)
Through hole tap [TH-1.6 series]
● M1.4 P=0.3M2 P=0.4M2.5 P=0.45M2.6 P=0.45M3 P=0.5
● 100 pieces are included in 1 pack.● Adsorption films are not put on thebulk products.
For surfacemounting
マックエイトのプリント板用端子
For surfacemounting
-246-
Dφ Cφ
Please attach the land on theboth sides.
■ Recommended fitting land
4-0.5
DφCφ
Shaded part: Opening
■ Recommended metal mask(Recommended metal mask thickness:150μto 200μ)
Part number φC φD
TH-1.6-□-M1.4 2.2 4.0
TH-1.6-□-M2 2.7 5.0
TH-1.6-□-M2.5 3.3 5.5
TH-1.6-□-M2.6 3.3 5.5
TH-1.6-□-M3 3.7 6.0
+0.1-0
Part number φC φDTH-1.6-□-M1.4 2.2 4.0TH-1.6-□-M2 2.7 5.0TH-1.6-□-M2.5 3.3 5.5TH-1.6-□-M2.6 3.3 5.5TH-1.6-□-M3 3.7 6.0
+0.1-0
スルーホールタップ〔TH-1.6シリーズ〕
・If it is bigger than the recommendedfitting through hole (φ C), the torqueto the Y-direction (soldering face side)will be decreased. (As the flow ofsoldering to the through hole isreduced)
Through hole tap [TH-1.6 series] specification
H
TH-1.6-2.0-M1.4
TH-1.6-2.5 to 3.0-M1.4
TH-1.6-3.5 to 4.0-M1.4
TH-1.6-4.5 to 5.0-M1.4
■ Dimension of the reel(TH-1.6-□-M1.4)
8±0.12±0.1
H±0.1
A
ABB
4±0.1
5.5±0.3
3φ±0.1
(C1)12±0.3
1.75±0.1
0.4±0.05
+0.10
1.5φ
A-A cross-sectional drawing
B-B cross-sectional drawing
180
Dimension of the reel Dimension of the tape
CTH-1.6-0.5 to 1.0 1.5TH-1.6-1.5 to 2.0 2.3
TH-1.6-2.5 to 3.5 3.8TH-1.6-4.0 to 5.0 5.3
A BM2 type 4.3 2.8M2.5 type 4.8 3.4M2.6 type 4.8 3.4M3 type 5.3 3.8
■ Dimension of the reel(TH-1.6-0.5 to TH-1.6-5.0)
H WTH-1.6-5.5 to 6.0 7.8 17.5TH-1.6-6.5 to 7.0 8.8 17.5TH-1.6-7.5 to 8.0 9.8 17.5TH-1.6-8.5 to 9.0 10.8 17.5TH-1.6-9.5 to 10 11.8 17.5(M2.5、M2.6 type)TH-1.6-9.5 to 10 11.8 25.5(M3 type)
E F GM2 type 4.3 7.5 16M2.5 type 4.8 7.5 16M2.6 type 4.8 7.5 16M 3 type 5.3 7.5 16(5.5 to 9.0)M 3 type 5.3 11.5 24(9.5 to 10)
■ Dimension of the reel(TH-1.6-5.5 to TH-1.6-10)
13φ±0.5
21φ±0.8
Eφ±0.1
4±0.1 2±0.1
12±0.1
0.4±0.05
1.5φ+0.1 0
H±0.1
1.75±0.1
F±0.1
G±0.3
80φ
254φ
W
Y-Y cross-sectional drawing
X-X cross-sectional drawing
X
XY Y
Dimension of the reelDimension of the tape
Dimension of the reel Dimension of the tape
X-X cross-sectional drawing
Y-Y cross-sectional drawing
X
XYY18
0
3.8
4.8
5.8
6.8
マックエイトのプリント板用端子
-247-
4±0.1
B B
A
A
H±0.1
2±0.116±0.1
T±0.05
1.75±0.1
11.5±0.1
24±0.3
φ1.5
9.3φ±0.1
+0.110
Through hole tap〔TH-1.6-□-M5 Series〕
■ Part number
●
●
●
●
●
●
●
●
●
●
●
A chip mounter can be used for this spacer.A spacer can be fit on a PC board just by automatically loading it on the PC board and carrying out reflow.It can be fit from the part face, soldering face and both sides.Tape-and-reel has an adsorption film. Please remove by pushing it from the opposite side after reflow.The jig for removing adsorption films (Part number: TH-JIG) is available.Material: BrassFinish: Tin plating over nickel baseRated current: 50ATightening torque: 15kgf-㎝(147N-㎝)or lessAdaptive printed board thickness: 1.6t or over(There is no problem if it is used for other board thickness.)Please use the automatic mounter of automatic recognition type.
■ Example of usage
Part number HTH-1.6-2.0-M5 2.5 〃 3.0 〃 3.5 〃 4.0 〃 4.5 〃 5.0 〃 5.5 〃 6.0 〃 6.5 〃 7.0 〃 7.5 〃 8.0 〃 8.5 〃 9.0 〃 9.5 〃 10 〃
2.02.53.03.54.04.55.05.56.06.57.07.58.08.59.09.510
Number of taps included in the reel500pcs400pcs400pcs350pcs350pcs300pcs300pcs250pcs250pcs200pcs200pcs200pcs200pcs150pcs150pcs150pcs150pcs
Part NumberReel Tape
TH-1.6-2.0-M5 2.5 〃 3.0 〃 3.5 〃 4.0 〃 4.5 〃 5.0 〃 5.5 〃 6.0 〃
254254254254254254254254254
808080808080808080
0.40.40.40.40.40.40.40.40.4
3.84.84.85.85.86.86.87.87.8
■ Dimension of the reel
a(φ) b(φ) T HPart Number
Reel Tape
TH-1.6-6.5-M5 7.0 〃 7.5 〃 8.0 〃 8.5 〃 9.0 〃 9.5 〃 10 〃
0.40.40.40.40.50.50.50.5
8080808080808080
254254254254254254254254
8.88.89.89.810.810.811.811.8
a(φ) b(φ) T H
25.5
φb
φa
A-A cross-sectional drawing
B-B cross-sectional drawing
Dimension of the reelDimension of the tape
φ7.2 φ10
Shaded part: Opening
■ Recommended metal mask(Recommended metal mask
thickness:150μ to 200μ)
■ Recommended fitting land
■ To order separate productTH-1.6-3.0-M5-B
Condition of fitting the panel to theprinted board
■ Dimension
φ9.0
φ7.0
M5 P=0.8Adsorption film
H1.5
■ Condition of fitting to thePC board
H
PC board1.6
It does not protrude to the soldering face side.
~~
Please specify –B.
▲ Use of a through hole tap is limited to athrough hole board. (It is impossible to use itfor a one-sided board and non through holeboard.)
φ7.2 φ10 or over+0.1-0
Please attach the land on the both sides.
With the M5 solderless terminal attached
● 100 pieces are included in 1 pack.● Adsorption films are not put on the bulkproducts.
For surfacemounting
マックエイトのプリント板用端子
-248-
For surfacemounting
■ To order bulk product
TH-1.6-0.5-4-40-B
● 100 pieces are included in 1 pack.● Adsorption films are not put on the bulk products.
With the adsorption film removed after reflow
スルーホールタップ〔TH-1.6シリーズ〕
■ Example of usage
Condition of fitting the panel to theprinted board
Part number Number of taps included in the reel
TH-1.6-0.5-2-56
TH-1.6-1.0-2-56
TH-1.6-1.5-2-56
TH-1.6-2.0-2-56
TH-1.6-2.5-2-56
TH-1.6-3.0-2-56
TH-1.6-3.5-2-56
TH-1.6-4.0-2-56
TH-1.6-4.5-2-56
TH-1.6-5.0-2-56
TH-1.6-5.5-2-56
TH-1.6-6.0-2-56
TH-1.6-6.5-2-56
TH-1.6-7.0-2-56
TH-1.6-7.5-2-56
TH-1.6-8.0-2-56
TH-1.6-8.5-2-56
TH-1.6-9.0-2-56
TH-1.6-9.5-2-56
TH-1.6-10-2-56
TH-1.6-0.5-4-40
TH-1.6-1.0-4-40
TH-1.6-1.5-4-40
TH-1.6-2.0-4-40
TH-1.6-2.5-4-40
TH-1.6-3.0-4-40
TH-1.6-3.5-4-40
TH-1.6-4.0-4-40
TH-1.6-4.5-4-40
TH-1.6-5.0-4-40
TH-1.6-5.5-4-40
TH-1.6-6.0-4-40
TH-1.6-6.5-4-40
TH-1.6-7.0-4-40
TH-1.6-7.5-4-40
TH-1.6-8.0-4-40
TH-1.6-8.5-4-40
TH-1.6-9.0-4-40
TH-1.6-9.5-4-40
TH-1.6-10-4-40
A
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
B
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
H
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
7.5
8.0
8.5
9.0
9.5
10
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
7.5
8.0
8.5
9.0
9.5
10
M
2-56
2-56
2-56
2-56
2-56
2-56
2-56
2-56
2-56
2-56
2-56
2-56
2-56
2-56
2-56
2-56
2-56
2-56
2-56
2-56
4-40
4-40
4-40
4-40
4-40
4-40
4-40
4-40
4-40
4-40
4-40
4-40
4-40
4-40
4-40
4-40
4-40
4-40
4-40
4-40
450pcs
450pcs
450pcs
450pcs
350pcs
350pcs
350pcs
250pcs
250pcs
250pcs
350pcs
350pcs
300pcs
300pcs
300pcs
300pcs
250pcs
250pcs
250pcs
250pcs
450pcs
450pcs
450pcs
450pcs
350pcs
350pcs
350pcs
250pcs
250pcs
250pcs
350pcs
350pcs
300pcs
300pcs
300pcs
300pcs
250pcs
250pcs
250pcs
250pcs
TH-1.6-2.0-6-32
TH-1.6-2.5-6-32
TH-1.6-3.0-6-32
TH-1.6-3.5-6-32
TH-1.6-4.0-6-32
TH-1.6-4.5-6-32
TH-1.6-5.0-6-32
TH-1.6-5.5-6-32
TH-1.6-6.0-6-32
TH-1.6-6.5-6-32
TH-1.6-7.0-6-32
TH-1.6-7.5-6-32
TH-1.6-8.0-6-32
TH-1.6-8.5-6-32
TH-1.6-9.0-6-32
TH-1.6-9.5-6-32
TH-1.6-10-6-32
A
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
B
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
H
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
7.5
8.0
8.5
9.0
9.5
10
M
6-32
6-32
6-32
6-32
6-32
6-32
6-32
6-32
6-32
6-32
6-32
6-32
6-32
6-32
6-32
6-32
6-32
250pcs
200pcs
200pcs
450pcs
450pcs
300pcs
300pcs
250pcs
250pcs
200pcs
200pcs
200pcs
200pcs
200pcs
200pcs
150pcs
150pcs
Part number Number of taps included in the reel
■ When it is fit to the PC board
H
PC board1.6
X-direction
Y-directionIt does not protrude to the soldering face side
~~
Please specify –B.
■ Part number
▲ Use of a through hole tap is limited to a through hole board. (It is impossible to use it for a one-sided board and non through hole board.)
Through hole tap [TH-1.6 series] (inch type)● A chip mounter can be used for this spacer.● A spacer can be fit on a PC board just by automatically loading it on the PC board and carrying out withreflow.
● It can be fit from the part face, soldering face and both sides.● Tape-and-reel has an adsorption film. Please remove by pushing it from the oppositeside after reflow.
● The jig for removing adsorption films (Part number: TH-JIG) is available.● Material: Brass● Finish: Tin plating over nickel base● Rated current:
TH-1.6-□-2-56 ……20ATH-1.6-□-4-40 ……30ATH-1.6-□-6-32 ……40A
● Tightening torque:TH-1.6-□-2-56……3kgf-cm(29.4N-cm)or lessTH-1.6-□-4-40……5kgf-cm(49N-cm)or less(X-direction)
3kgf-cm(29.4N-cm)or less(Y-direction)TH-1.6-□-6-32……8kgf-cm(78.4N-cm)or less
● Adaptive printed board thickness: 1.6t or over(There is no problem if it is used for other board thickness.)
● Please use the automatic mounter of automatic recognition type.
No2-56 P=0.4536No4-40 P=0.6350No6-32 P=0.7938
Aφ
Bφ
MAdsorption film
H1.5
■ Dimension
マックエイトのプリント板用端子マックエイトのプリント板用端子
FφEφ
Please attach the land on theboth sides.
■ Recommended fittingland
Shaded part: Opening
■ Recommended metal mask(Recommended metal mask thickness:150μ to 200μ)
Part number φE φF
TH-1.6-□-2-56 3.3 5.5
TH-1.6-□-4-40 3.7 6.0
TH-1.6-□-6-32 5.7 8.0
+0.1-0
・If it is bigger than the recommended fitting through hole (φ E), the torque to the Y-direction (soldering face side) will be decreased. (As the flow of soldering to thethrough hole is reduced)
Dimension of the reel
Dimension of the tape
X-X cross-sectionaldrawing
Y-Y cross-sectional drawing
X
X
Y Y
■ Dimension of the reel
Part number
TH-1.6-0.5-2-56TH-1.6-1.0-2-56TH-1.6-1.5-2-56TH-1.6-2.0-2-56TH-1.6-2.5-2-56TH-1.6-3.0-2-56TH-1.6-3.5-2-56TH-1.6-4.0-2-56TH-1.6-4.5-2-56TH-1.6-5.0-2-56TH-1.6-5.5-2-56TH-1.6-6.0-2-56TH-1.6-6.5-2-56TH-1.6-7.0-2-56TH-1.6-7.5-2-56TH-1.6-8.0-2-56TH-1.6-8.5-2-56TH-1.6-9.0-2-56TH-1.6-9.5-2-56TH-1.6-10-2-56TH-1.6-0.5-4-40TH-1.6-1.0-4-40TH-1.6-1.5-4-40TH-1.6-2.0-4-40TH-1.6-2.5-4-40TH-1.6-3.0-4-40TH-1.6-3.5-4-40TH-1.6-4.0-4-40TH-1.6-4.5-4-40
a(φ) b(φ)Reel Tape
W A B C D F G P180180180180180180180180180180254254254254254254254254254254180180180180180180180180180
6060606060606060606080808080808080808080606060606060606060
1313131313131313131317.517.517.517.517.517.517.517.517.517.5131313131313131313
4.84.84.84.84.84.84.84.84.84.84.84.84.84.84.84.84.84.84.84.85.35.35.35.35.35.35.35.35.3
3.43.43.43.43.43.43.43.43.43.400000000003.83.83.83.83.83.83.83.83.8
1.31.52.32.33.83.83.85.05.05.07.87.88.88.89.89.810.810.811.811.81.51.52.32.33.83.83.85.35.3
1.71.71.71.71.71.71.71.71.71.700000000001.71.71.71.71.71.71.71.71.7
5.55.55.55.55.55.55.55.55.55.57.57.57.57.57.57.57.57.57.57.55.55.55.55.55.55.55.55.55.5
1212121212121212121216161616161616161616121212121212121212
888888888812121212121212121212888888888
TH-1.6-5.0-4-40TH-1.6-5.5-4-40TH-1.6-6.0-4-40TH-1.6-6.5-4-40TH-1.6-7.0-4-40TH-1.6-7.5-4-40TH-1.6-8.0-4-40TH-1.6-8.5-4-40TH-1.6-9.0-4-40TH-1.6-9.5-4-40TH-1.6-10- 4-40TH-1.6-2.0-6-32TH-1.6-2.5-6-32TH-1.6-3.0-6-32TH-1.6-3.5-6-32TH-1.6-4.0-6-32TH-1.6-4.5-6-32TH-1.6-5.0-6-32TH-1.6-5.5-6-32TH-1.6-6.0-6-32TH-1.6-6.5-6-32TH-1.6-7.0-6-32TH-1.6-7.5-6-32TH-1.6-8.0-6-32TH-1.6-8.5-6-32TH-1.6-9.0-6-32TH-1.6-9.5-6-32TH-1.6-10-6-32
a(φ) b(φ) W A B C D F G P180254254254254254254254254254254178178178254254254254254254254254254254254254254254
60808080808080808080808080808080808080808080808080808080
1317.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.525.525.525.525.525.525.525.525.525.525.5
5.35.35.35.35.35.35.35.35.35.35.37.37.37.37.37.37.37.37.37.37.37.37.37.37.37.37.37.3
3.8000000000000000000000000000
5.37.87.88.88.89.89.810.810.811.811.84.05.05.06.06.07.07.08.08.09.09.01010111111.811.8
1.7000000000000000000000000000
5.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.511.511.511.511.511.511.511.511.511.511.5
12161616161616161616161616161616161624242424242424242424
8121212121212121212121212121212121216161616161616161616
Part numberReel Tape
■Part number
Through hole tap [TH-1.6 series] (inch type) specification
-249-
For surfacemounting
マックエイトのプリント板用端子
-250-
For surfacemounting
マックエイトのプリント板用端子
● A chip mounter can be used for this spacer.● A spacer can be fit on a PC board just by automatically loading it on the PC board and carrying outreflow.
● It can be fit from the part face, soldering face and the both sides.● Tape-and-reel has an adsorption film. Please remove by pushing it from the oppositeside after reflow.
● The jig for removing adsorption films (Part number: TH-JIG) is available.● Material: Brass● Finish: Tin plating over nickel base● Rated current:
TH-0.8-□-M2.5……20ATH-0.8-□-M2.6……20ATH-0.8-□-M3 ……30ATH-0.8-□-M4 ……40A
● Tightening torque:TH-0.8-□-M2.5……3kgf-cm(29.4N-cm)or lessTH-0.8-□-M2.6……3kgf-cm(29.4N-cm)or lessTH-0.8-□-M3……5kgf-cm(49N-cm)or less(X-direction)
3kgf-cm(29.4N-cm)or less(Y-direction)TH-0.8-□-M4……8kgf-cm(78.4N-cm)or less
● Adaptive printed board thickness: 0.8t or over(There is no problem if it is used for other board thickness.)
● Please use the automatic mounter of automatic recognition type.
■ To order bulk productTH-0.8-0.5-M3-B
● 100 pieces are included in 1 pack.● Adsorption films are not put on the bulk products.
With the adsorption film removed after reflow
Through hole tap [TH-0.8 series]
■ Example of usage
Condition of fitting the panel to theprinted board
■ Dimension
Part number Number of taps included in the reel
TH-0.8-1.0-M2.5
TH-0.8-1.5-M2.5
TH-0.8-2.0-M2.5
TH-0.8-2.5-M2.5
TH-0.8-3.0-M2.5
TH-0.8-3.5-M2.5
TH-0.8-4.0-M2.5
TH-0.8-4.5-M2.5
TH-0.8-5.0-M2.5
TH-0.8-5.5-M2.5
TH-0.8-6.0-M2.5
TH-0.8-6.5-M2.5
TH-0.8-7.0-M2.5
TH-0.8-7.5-M2.5
TH-0.8-8.0-M2.5
TH-0.8-8.5-M2.5
TH-0.8-9.0-M2.5
TH-0.8-9.5-M2.5
TH-0.8-10-M2.5
TH-0.8-1.0-M2.6
TH-0.8-1.5-M2.6
TH-0.8-2.0-M2.6
TH-0.8-2.5-M2.6
TH-0.8-3.0-M2.6
TH-0.8-3.5-M2.6
TH-0.8-4.0-M2.6
TH-0.8-4.5-M2.6
TH-0.8-5.0-M2.6
TH-0.8-5.5-M2.6
TH-0.8-6.0-M2.6
TH-0.8-6.5-M2.6
TH-0.8-7.0-M2.6
TH-0.8-7.5-M2.6
TH-0.8-8.0-M2.6
TH-0.8-8.5-M2.6
TH-0.8-9.0-M2.6
TH-0.8-9.5-M2.6
TH-0.8-10-M2.6
TH-0.8-1.2-M3
TH-0.8-1.5-M3
A
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
5.0
5.0
B
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.5
3.5
H
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
7.5
8.0
8.5
9.0
9.5
10
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
7.5
8.0
8.5
9.0
9.5
10
1.2
1.5
M
M2.5
M2.5
M2.5
M2.5
M2.5
M2.5
M2.5
M2.5
M2.5
M2.5
M2.5
M2.5
M2.5
M2.5
M2.5
M2.5
M2.5
M2.5
M2.5
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
M3
M3
450pcs
450pcs
450pcs
350pcs
350pcs
350pcs
250pcs
250pcs
250pcs
350pcs
350pcs
300pcs
300pcs
300pcs
300pcs
250pcs
250pcs
250pcs
250pcs
450pcs
450pcs
450pcs
350pcs
350pcs
350pcs
250pcs
250pcs
250pcs
350pcs
350pcs
300pcs
300pcs
300pcs
300pcs
250pcs
250pcs
250pcs
250pcs
450pcs
450pcs
TH-0.8-2.0-M3
TH-0.8-2.5-M3
TH-0.8-3.0-M3
TH-0.8-3.5-M3
TH-0.8-4.0-M3
TH-0.8-4.5-M3
TH-0.8-5.0-M3
TH-0.8-5.5-M3
TH-0.8-6.0-M3
TH-0.8-6.5-M3
TH-0.8-7.0-M3
TH-0.8-7.5-M3
TH-0.8-8.0-M3
TH-0.8-8.5-M3
TH-0.8-9.0-M3
TH-0.8-9.5-M3
TH-0.8-10- M3
TH-0.8-2.0-M4
TH-0.8-2.5-M4
TH-0.8-3.0-M4
TH-0.8-3.5-M4
TH-0.8-4.0-M4
TH-0.8-4.5-M4
TH-0.8-5.0-M4
TH-0.8-5.5-M4
TH-0.8-6.0-M4
TH-0.8-6.5-M4
TH-0.8-7.0-M4
TH-0.8-7.5-M4
TH-0.8-8.0-M4
TH-0.8-8.5-M4
TH-0.8-9.0-M4
TH-0.8-9.5-M4
TH-0.8-10-M4
A
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
B
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
H
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
7.5
8.0
8.5
9.0
9.5
10
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
7.5
8.0
8.5
9.0
9.5
10
M
M3
M3
M3
M3
M3
M3
M3
M3
M3
M3
M3
M3
M3
M3
M3
M3
M3
M4
M4
M4
M4
M4
M4
M4
M4
M4
M4
M4
M4
M4
M4
M4
M4
M4
450pcs
350pcs
350pcs
350pcs
250pcs
250pcs
250pcs
350pcs
350pcs
300pcs
300pcs
300pcs
300pcs
250pcs
250pcs
250pcs
250pcs
350pcs
250pcs
250pcs
200pcs
200pcs
450pcs
450pcs
300pcs
300pcs
250pcs
250pcs
200pcs
200pcs
200pcs
200pcs
200pcs
200pcs
Part number Number of taps included in the reel
■ Condition of fitting to the PC board
~~
Please specify B.
● M2.5 P=0.45M2.6 P=0.45M3 P=0.5M4 P=0.7
■ Part number
H
PC board0.8
X-direction
Y-directionIt does not protrude to the soldering face side
Adsorption film
▲ Use of a through hole tap is limitedto a through hole board. (It isimpossible to use it for a one-sidedboard and non through hole board.)
マックエイトのプリント板用端子マックエイトのプリント板用端子スルーホールタップ〔TH-0.8シリーズ〕 PAT.PRoHS対応Through hole tap [TH-0.8 series] specification
FφEφ
Please attach the land on the both sides.
■ Recommended fitting land
Shaded part: Opening
■ Recommended metal mask(Recommended metal mask thickness:150μ to 200μ)
Part number φE φF
TH-0.8-□-M2.5 3.3 5.5
TH-0.8-□-M2.6 3.3 5.5
TH-0.8-□-M3 3.7 6.0
TH-0.8-□-M4 5.7 8.0
+0.1-0
・If it is bigger than the recommended fitting through hole (φ E), the torque to the Y-direction (soldering face side) will be decreased. (As the flow of soldering to the throughhole is reduced)
Dimension of the reel
Dimension of the tape
X-X cross-sectional drawing
Y-Y cross-sectional drawing
X
X
Y Y
■ Dimension of the reel
Part number
TH-0.8-1.0-M2.6TH-0.8-1.5-M2.6TH-0.8-2.0-M2.6TH-0.8-2.5-M2.6TH-0.8-3.0-M2.6TH-0.8-3.5-M2.6TH-0.8-4.0-M2.6TH-0.8-4.5-M2.6TH-0.8-5.0-M2.6TH-0.8-5.5-M2.6TH-0.8-6.0-M2.6TH-0.8-6.5-M2.6TH-0.8-7.0-M2.6TH-0.8-7.5-M2.6TH-0.8-8.0-M2.6TH-0.8-8.5-M2.6TH-0.8-9.0-M2.6TH-0.8-9.5-M2.6TH-0.8-10-M2.6TH-0.8-1.2-M3TH-0.8-1.5-M3TH-0.8-2.0-M3TH-0.8-2.5-M3TH-0.8-3.0-M3TH-0.8-3.5-M3TH-0.8-4.0-M3TH-0.8-4.5-M3TH-0.8-5.0-M3
a(φ) b(φ)Reel Tape
W A B C D F G P180180180180180180180180180254254254254254254254254254254180180180180180180180180180
60606060606060606080808080808080808080606060606060606060
13131313131313131317.517.517.517.517.517.517.517.517.517.5131313131313131313
4.84.84.84.84.84.84.84.84.84.84.84.84.84.84.84.84.84.84.85.35.35.35.35.35.35.35.35.3
3.43.43.43.43.43.43.43.43.400000000003.83.83.83.83.83.83.83.83.8
1.32.32.33.83.83.85.05.05.06.86.87.87.88.88.89.89.810.810.81.52.32.33.83.83.85.35.35.3
1.71.71.71.71.71.71.71.71.700000000001.71.71.71.71.71.71.71.71.7
5.55.55.55.55.55.55.55.55.57.57.57.57.57.57.57.57.57.57.55.55.55.55.55.55.55.55.55.5
12121212121212121216161616161616161616121212121212121212
88888888812121212121212121212888888888
TH-0.8-5.5-M3TH-0.8-6.0-M3TH-0.8-6.5-M3TH-0.8-7.0-M3TH-0.8-7.5-M3TH-0.8-8.0-M3TH-0.8-8.5-M3TH-0.8-9.0-M3TH-0.8-9.5-M3TH-0.8-10- M3TH-0.8-2.0-M4TH-0.8-2.5-M4TH-0.8-3.0-M4TH-0.8-3.5-M4TH-0.8-4.0-M4TH-0.8-4.5-M4TH-0.8-5.0-M4TH-0.8-5.5-M4TH-0.8-6.0-M4TH-0.8-6.5-M4TH-0.8-7.0-M4TH-0.8-7.5-M4TH-0.8-8.0-M4TH-0.8-8.5-M4TH-0.8-9.0-M4TH-0.8-9.5-M4TH-0.8-10-M4
a(φ) b(φ) W A B C D F G P254254254254254254254254254254178178178178178254254254254254254254254254254254254
808080808080808080808080808080808080808080808080808080
17.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.525.525.525.525.525.525.525.525.525.525.5
5.35.35.35.35.35.35.35.35.35.37.37.37.37.37.37.37.37.37.37.37.37.37.37.37.37.37.3
000000000000000000000000000
6.86.87.87.88.88.89.89.810.810.83.04.04.05.05.06.06.07.07.08.08.09.09.010101111
000000000000000000000000000
7.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.511.511.511.511.511.511.511.511.511.511.5
161616161616161616161616161616161624242424242424242424
121212121212121212121212121212121216161616161616161616
・The M2.5 type is the same as the M2.6.
Part numberReel Tape
■ Part number
-251-
For surfacemounting
マックエイトのプリント板用端子
For surfacemounting
-252-
● A chip mounter can be used for this spacer.● A spacer can be fit on a PC board just by automatically loading it on the PC board and carrying outreflow.
● It can be fit from the part face, soldering face and the both sides.● Tape-and-reel has an adsorption film. Please remove by pushing it from the oppositeside after reflow.
● The jig for removing adsorption films (Part number: TH-JIG) is available.● Material: Brass● Finish: Tin plating over nickel base● Rated current:
TH-0.8-□-2-56 ……20ATH-0.8-□-4-40 ……30A
● Tightening torque:TH-0.8-□-2-56……3kgf-cm(29.4N-cm)or lessTH-0.8-□-4-40……5kgf-cm(49N-cm)or less(X-direction)
3kgf-cm(29.4N-cm)or less(Y-direction)● Adaptive printed board thickness: 0.8t or over(There is no problem if it is used for other board thickness.)
● Please use the automatic mounter of automatic recognition type.
マックエイトのプリント板用端子
■ To order bulk productTH-1.6-2.0-4-40-B
● 100 pieces are included in 1 pack.● Adsorption films are not put on the bulk products.
With the adsorption film removed after reflow
スルーホールタップ〔TH-1.6シリーズ〕
■ Example of usage
Condition of fitting the panel to the printedboard
■ Dimension
Part numberNumber of taps included in the reel
TH-0.8-1.0-2-56
TH-0.8-1.5-2-56
TH-0.8-2.0-2-56
TH-0.8-2.5-2-56
TH-0.8-3.0-2-56
TH-0.8-3.5-2-56
TH-0.8-4.0-2-56
TH-0.8-4.5-2-56
TH-0.8-5.0-2-56
TH-0.8-5.5-2-56
TH-0.8-6.0-2-56
TH-0.8-6.5-2-56
TH-0.8-7.0-2-56
TH-0.8-7.5-2-56
TH-0.8-8.0-2-56
TH-0.8-8.5-2-56
TH-0.8-9.0-2-56
TH-0.8-9.5-2-56
TH-0.8-10-2-56
TH-0.8-1.5-4-40
TH-0.8-2.0-4-40
TH-0.8-2.5-4-40
TH-0.8-3.0-4-40
TH-0.8-3.5-4-40
TH-0.8-4.0-4-40
TH-0.8-4.5-4-40
TH-0.8-5.0-4-40
TH-0.8-5.5-4-40
TH-0.8-6.0-4-40
TH-0.8-6.5-4-40
TH-0.8-7.0-4-40
TH-0.8-7.5-4-40
TH-0.8-8.0-4-40
TH-0.8-8.5-4-40
TH-0.8-9.0-4-40
TH-0.8-9.5-4-40
TH-0.8-10-4-40
A
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
B
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
H
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
7.5
8.0
8.5
9.0
9.5
10
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
7.5
8.0
8.5
9.0
9.5
10
M
2-56
2-56
2-56
2-56
2-56
2-56
2-56
2-56
2-56
2-56
2-56
2-56
2-56
2-56
2-56
2-56
2-56
2-56
2-56
4-40
4-40
4-40
4-40
4-40
4-40
4-40
4-40
4-40
4-40
4-40
4-40
4-40
4-40
4-40
4-40
4-40
4-40
450pcs
450pcs
450pcs
350pcs
350pcs
350pcs
250pcs
250pcs
250pcs
350pcs
350pcs
300pcs
300pcs
300pcs
300pcs
250pcs
250pcs
250pcs
250pcs
450pcs
450pcs
350pcs
350pcs
350pcs
250pcs
250pcs
250pcs
350pcs
350pcs
300pcs
300pcs
300pcs
300pcs
250pcs
250pcs
250pcs
250pcs
Aφ
Bφ
MAdsorption film
H0.7
~~
Please specify –B.
■ Part number
● TH-0.8-□-2-56 carrier tape is the same as that of the TH-0.8-□-M2.6● TH-0.8-□-4-40 carrier tape is the same as that of the TH-0.8-□-M3▲ Use of a through hole tap is limited to a through hole board. (It is impossible to use it for a one-sidedboard and non through hole board.)
Through hole tap [TH-0.8 series] (inch type)
FφEφ
Please attach the land on the both sides.
■ Recommendedfitting land
Shaded part: Opening
■ Recommended metal mask(Recommended metal mask thickness:150μto200μ)
Part number φE φF
TH-0.8-□-2-56 3.3 5.5
TH-0.8-□-4-40 3.7 6.0
+0.1-0
■ When it is fit to the PC board
H
PC board0.8
X-direction
Y-directionIt does not protrude to the soldering face side
No2-56 P=0.4536No4-40 P=0.6350
● If it is bigger than the recommended fitting through hole (φ E), the torque to theY-direction (soldering face side) will be decreased. (As the flow of soldering to thethrough hole is reduced)
マックエイトのプリント板用端子
● A through hole changes to a threaded hole (M1.0, M1.2, M1.4, M1.6, M1.7 and M2).● This tap can fit to various items.● Taping type has an adsorption film. Please remove by pushing it from the opposite side after reflow.● The jig for removing adsorption films (Part number: TH-JIG) is available.● Material: Brass● Finish: Tin plating over nickel base● Rated current:
TH-□-□-M1.0……10A TH-□-□-M1.7……15ATH-□-□-M1.2……12A TH-□-□-M2………20ATH-□-□-M1.4……12ATH-□-□-M1.6……15A
● Tightening torque:TH-□-□-M1.0……0.3kgf-cm(2.94N-cm)or lessTH-□-□-M1.2……0.6kgf-cm(5.88N-cm)or lessTH-□-□-M1.4……1.0kgf-cm(9.8N-cm)or lessTH-□-□-M1.6……1.5kgf-cm(14.7N-cm)or lessTH-□-□-M1.7……1.5kgf-cm(14.7N-cm)or lessTH-□-□-M2 …… 1.5kgf-cm(14.7N-cm)or less
● Adaptive printed board thickness: 0.6t or over (TH-0.6 series), 0.8t or over (TH-0.8 series)(There is no problem if it is used for other board thickness.)
● Recommended metal mask thickness:150μ to 200μ
Through hole tap [TH-0.6, 0.8 (M1.0, M1.2, M1.4, M1.6, M1.7, M2) series]
■ Dimension
Aφ
Bφ
MAdsorption film
HC
H
PC board0.6It does not protrude to the soldering face side
H
PC board0.8It does not protrude to the soldering face side
M1.0 P=0.25M1.2 P=0.25M1.4 P=0.3M1.6 P=0.35M1.7 P=0.35M2 P=0.4
Condition of fitting the panel to theprinted board
TH-0.6-□-M□
TH-0.8-□-M□
TH-0.6-0.5-M1.0 1.0 1.5 2.0 2.5 3.0TH-0.6-0.5-M1.2 1.0 1.5 2.0 2.5 3.0TH-0.6-0.7-M1.4 1.0 1.5 2.0 2.5 3.0TH-0.6-0.8-M1.6 1.0 1.5 2.0 2.5 3.0TH-0.6-0.8-M1.7 1.0 1.5 2.0 2.5 3.0TH-0.6-1.1-M2 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
A
2.52.52.52.52.52.52.52.52.52.52.52.52.72.72.72.72.72.73.03.03.03.03.03.03.03.03.03.03.03.04.04.04.04.04.04.04.04.04.0
B C
1.61.61.61.61.61.61.81.81.81.81.81.82.02.02.02.02.02.02.22.22.22.22.22.22.32.32.32.32.32.32.52.52.52.52.52.52.52.52.5
H
0.51.01.52.02.53.00.51.01.52.02.53.00.71.01.52.02.53.00.81.01.52.02.53.00.81.01.52.02.53.01.11.52.02.53.03.54.04.55.0
0.450.450.450.450.450.450.450.450.450.450.450.450.450.450.450.450.450.450.450.450.450.450.450.450.450.450.450.450.450.450.450.450.450.450.450.450.450.450.45
M
M1.0M1.0M1.0M1.0M1.0M1.0M1.2M1.2M1.2M1.2M1.2M1.2M1.4M1.4M1.4M1.4M1.4M1.4M1.6M1.6M1.6M1.6M1.6M1.6M1.7M1.7M1.7M1.7M1.7M1.7M2M2M2M2M2M2M2M2M2
1000pcs1000pcs600pcs600pcs500pcs500pcs1000pcs1000pcs600pcs600pcs500pcs500pcs1000pcs1000pcs700pcs700pcs500pcs500pcs900pcs900pcs900pcs600pcs500pcs500pcs900pcs900pcs900pcs600pcs500pcs500pcs600pcs600pcs600pcs450pcs450pcs450pcs350pcs350pcs350pcs
TH-0.8-1.0-M1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0TH-0.8-1.0-M1.2 1.5 2.0 2.5 3.0TH-0.8-1.0-M1.4 1.5 2.0 2.5 3.0TH-0.8-0.6-M1.6 1.0 1.5 2.0 2.5 3.0TH-0.8-0.6-M1.7 1.0 1.5 2.0 2.5 3.0TH-0.8-1.0-M2 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
A
2.52.52.52.52.52.52.52.52.52.52.52.52.52.52.72.72.72.72.73.03.03.03.03.03.03.03.03.03.03.03.04.04.04.04.04.04.04.04.04.0
B C
1.61.61.61.61.61.61.61.61.61.81.81.81.81.82.02.02.02.02.02.22.22.22.22.22.22.32.32.32.32.32.32.52.52.52.52.52.52.52.52.5
H
1.01.52.02.53.03.54.04.55.01.01.52.02.53.01.01.52.02.53.00.61.01.52.02.53.00.61.01.52.02.53.01.01.52.02.53.03.54.04.55.0
0.70.70.70.70.70.70.70.70.70.70.70.70.70.70.70.70.70.70.70.70.70.70.70.70.70.70.70.70.70.70.70.70.70.70.70.70.70.70.70.7
M
M1.0M1.0M1.0M1.0M1.0M1.0M1.0M1.0M1.0M1.2M1.2M1.2M1.2M1.2M1.4M1.4M1.4M1.4M1.4M1.6M1.6M1.6M1.6M1.6M1.6M1.7M1.7M1.7M1.7M1.7M1.7M2M2M2M2M2M2M2M2M2
600pcs600pcs600pcs500pcs500pcs300pcs300pcs300pcs300pcs600pcs600pcs600pcs500pcs500pcs700pcs700pcs500pcs500pcs400pcs900pcs900pcs600pcs600pcs500pcs500pcs900pcs900pcs600pcs600pcs500pcs500pcs450pcs450pcs450pcs350pcs350pcs350pcs250pcs250pcs250pcs
Part number Number of taps included in the reel Part number
Number of taps included in the reel
■ Part number
■ Example of usage
■ Condition of fitting tothe PC board
▲ Use of a through hole tap is limited to a through hole board. (It is impossible to use it for a one-sided board and nonthrough hole board.)
-253-
For surfacemounting
マックエイトのプリント板用端子
-254-
For surfacemounting
マックエイトのプリント板用端子Through hole tap [TH-0.6, 0.8 (M1.0, M1.2, M1.4, M1.6, M1.7, M2)] specification
Part number
TH-0.8-1.0-M2 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
A4.34.34.34.34.34.34.34.34.3
B C2.82.82.82.82.82.82.82.82.8
D1.71.71.71.71.71.71.71.71.7
1.32.32.33.83.83.85.35.35.3
TH-0.6-0.5-M1.0 1.0 1.5 2.0 2.5 3.0TH-0.6-0.5-M1.2 1.0 1.5 2.0 2.5 3.0TH-0.6-0.7-M1.4 1.0 1.5 2.0 2.5 3.0TH-0.6-0.8-M1.6 1.0 1.5 2.0 2.5 3.0TH-0.6-0.8-M1.7 1.0 1.5 2.0 2.5 3.0TH-0.6-1.1-M2 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
E H2.72.72.82.82.82.82.72.72.82.82.82.82.92.93.03.03.03.03.23.23.23.33.33.33.23.23.23.33.33.34.34.34.34.34.34.34.34.34.3
1.61.63.03.04.04.01.61.63.03.04.04.01.81.82.752.753.83.82.22.22.23.04.04.02.22.22.23.04.04.02.752.752.754.254.254.255.755.755.75
TH-0.8-1.0-M1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0TH-0.8-1.0-M1.2 1.5 2.0 2.5 3.0TH-0.8-1.0-M1.4 1.5 2.0 2.5 3.0TH-0.8-0.6-M1.6 1.0 1.5 2.0 2.5 3.0TH-0.8-0.6-M1.7 1.0 1.5 2.0 2.5 3.0
E H2.82.82.82.82.82.82.82.82.82.82.82.82.82.83.03.03.03.03.03.23.23.33.33.33.33.23.23.33.33.33.3
3.03.03.04.04.05.05.06.06.03.03.03.04.04.02.752.753.83.84.82.22.23.03.04.04.02.22.23.03.04.04.0
Part number Part number
13φ±0.5
1.75±0.1
21φ±0.8
60φ
180φ
13
Dimension of the reel Dimension of the tape
4±0.1 2±0.1
8±0.1 1.5φ+0.10
E±0.1
H±0.1
5.5±0.1
12±0.3
0.4±0.05
B-B cross-sectional drawing
A-A cross-sectional drawingA
AB B
8
5.5
12
■ Table of dimensions
■TH-0.8-□-M2 tape
Dimensional drawing of the tape
X-X cross-sectional drawing
Y-Y cross-sectional drawing
X
X
Y Y
+0.1-0
Please attach the land on the both sides.
■ Recommended fittingland
Shaded part: Opening
■ Recommended metal mask(Recommended metal mask thickness:150μ to 200μ)
Part number φE φFTH-□-□-M1.0 1.8 3.5TH-□-□-M1.2 2.0 3.5TH-□-□-M1.4 2.2 4.0TH-□-□-M1.6 2.4 4.0TH-□-□-M1.7 2.5 4.0TH-□-□-M2 2.7 5.0
マックエイトのプリント板用端子マックエイトのプリント板用端子
● A chip mounter can be used for this spacer.● A spacer can be fit on a PC board just by automatically loading it on the PC board and carrying outreflow.
● There is no adsorption film. It can be adsorbed as it is. (Please set the adsorption nozzle dimensionaccording to the external diameter.) (The bottom is closed.)
● Material: Brass● Finish: Tin plating over nickel base● Rated current:
THF-1.6-□-M2 ……20ATHF-1.6-□-M2.6……20ATHF-1.6-□-M3 ……30A
● Tightening torque:THF-1.6-□-M2……1.5kgf-cm(14.7N-cm)or lessTHF-1.6-□-M2.6……3kgf-cm(29.4N-cm)or lessTHF-1.6-□-M3……5kgf-cm(49N-cm)or less
● Adaptive printed board thickness: 1.6t or over(There is no problem if it is used for other board thickness.)
● Please use the automatic mounter of automatic recognition type.
Please attach the land on the both sides.
■ Recommended fitting land
■ To order bulk product
Shaded part: Opening
■ Recommended metal mask(Recommended metal mask thickness:150μ to 200μ)
Part number φC φD
THF-1.6-□-M2 2.7 5.0
THF-1.6-□-M2.6 3.3 5.5
THF-1.6-□-M3 3.7 6.0
THF-1.6-1.5-M2-B
● 100pcs/pack
When it is reflowed
+0.1-0
Part number φC φD
THF-1.6-□-M2 2.7 5.0
THF-1.6-□-M2.6 3.3 5.5
THF-1.6-□-M3 3.7 6.0
+0.1-0
Through hole tap [THF-1.6 series]
■ Example of usage
Condition of fitting the panel to theprinted board
■ Dimension
Part number Number of taps included in the reel
THF-1.6-1.5-M2
THF-1.6-2.0-M2
THF-1.6-2.5-M2
THF-1.6-3.0-M2
THF-1.6-3.5-M2
THF-1.6-4.0-M2
THF-1.6-4.5-M2
THF-1.6-5.0-M2
THF-1.6-5.5-M2
THF-1.6-6.0-M2
THF-1.6-6.5-M2
THF-1.6-7.0-M2
THF-1.6-7.5-M2
THF-1.6-8.0-M2
THF-1.6-1.5-M2.6
THF-1.6-2.0-M2.6
THF-1.6-2.5-M2.6
THF-1.6-3.0-M2.6
THF-1.6-3.5-M2.6
THF-1.6-4.0-M2.6
THF-1.6-4.5-M2.6
THF-1.6-5.0-M2.6
THF-1.6-5.5-M2.6
THF-1.6-6.0-M2.6
THF-1.6-6.5-M2.6
THF-1.6-7.0-M2.6
THF-1.6-7.5-M2.6
THF-1.6-8.0-M2.6
THF-1.6-1.5-M3
THF-1.6-2.0-M3
THF-1.6-2.5-M3
THF-1.6-3.0-M3
THF-1.6-3.5-M3
THF-1.6-4.0-M3
THF-1.6-4.5-M3
THF-1.6-5.0-M3
THF-1.6-5.5-M3
THF-1.6-6.0-M3
THF-1.6-6.5-M3
THF-1.6-7.0-M3
THF-1.6-7.5-M3
THF-1.6-8.0-M3
THF-1.6-8.5-M3
THF-1.6-9.0-M3
THF-1.6-9.5-M3
THF-1.6-10- M3
A
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
B C
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
H
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
7.5
8.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
7.5
8.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
7.5
8.0
8.5
9.0
9.5
10
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
7.5
8.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
7.5
8.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
7.5
8.0
8.5
9.0
9.5
10
M
M2
M2
M2
M2
M2
M2
M2
M2
M2
M2
M2
M2
M2
M2
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
M3
M3
M3
M3
M3
M3
M3
M3
M3
M3
M3
M3
M3
M3
M3
M3
M3
M3
450pcs
450pcs
350pcs
350pcs
350pcs
250pcs
250pcs
250pcs
350pcs
350pcs
300pcs
300pcs
300pcs
300pcs
450pcs
450pcs
350pcs
350pcs
350pcs
250pcs
250pcs
250pcs
350pcs
350pcs
300pcs
300pcs
300pcs
300pcs
450pcs
450pcs
350pcs
350pcs
350pcs
250pcs
250pcs
250pcs
350pcs
350pcs
300pcs
300pcs
300pcs
300pcs
250pcs
250pcs
250pcs
250pcs
C(Valid screw)
■ Condition of fitting to the PC board
PC boardIt does not protrude to the soldering face side
~~
Please specify –B.
● M2 P=0.4M2.6 P=0.45M3 P=0.5
■ Part number
▲ Use of a through hole tap is limited to a through hole board.
(It is impossible to use it for a one-sided board and non through hole board.)
-255-
For surfacemounting
マックエイトのプリント板用端子
-256-
For surfacemounting
マックエイトのプリント板用端子
C
THF-1.6-1.5 to 2.0 2.3
THF-1.6-2.5 to 3.5 3.8
THF-1.6-4.0 to 5.0 5.3
A B
M2 Type 4.3 2.8
M2.6 Type 4.8 3.4
M3 Type 5.3 3.8
■ Dimension of the reel(THF-1.6-1.5 to THF-1.6-5.0)
H W
THF-1.6-5.5 to 6.0 7.8 17.5
THF-1.6-6.5 to 7.0 8.8 17.5
THF-1.6-7.5 to 8.0 9.8 17.5
THF-1.6-8.5 to 9.0 10.817.5
THF-1.6-9.5 to 10 11.8 25.5
E F G
M2.6 Type 4.8 7.5 16
M 3 Type 5.3 7.5 16
(5.5 to 9.0)
M 3 Type 5.3 11.5 24
(9.5 to 10)
H
THF-1.6-5.5-M2 7.8
THF-1.6-6.0-M2 7.8
THF-1.6-6.5-M2 8.8
THF-1.6-7.0-M2 8.8
THF-1.6-7.5-M2 9.8
THF-1.6-8.0-M2 9.8
■ Dimension of the reel(THF-1.6-5.5 to THF-1.6-10)
■ Dimension of the reel(THF-1.6-6.0-M2 to THF-1.6-8.0-M2)
180
Dimension of the reel Dimension of the tape
X-X cross-sectional drawing
Y-Y cross-sectional drawing
X
XY Y
Dimension of the reel Dimension of the tape
A-A cross-sectional drawing
B-B cross-sectional drawing
Dimension of the through hole tap reel [THF-1.6 series]
Dimension of the reel Dimension of the tape
A-A cross-sectional drawing
B-B cross-sectional drawing
マックエイトのプリント板用端子
● A chip mounter can be used for this spacer.● A spacer can be fit on a PC board just by automatically loading it on the PC board and
carrying out reflow.● Insert a screw from the part face and fit it to the threaded hole on the chassis to fit and raise
the PC board above the chassis.● Tape-and-reel has an adsorption film. Please remove by pushing it from the opposite side
after reflow.● The jig for removing adsorption films (Part number: TH-JIG) is available.● Material: Brass● Finish: Tin plating over nickel base● Adaptive printed board thickness: 1.6t
(There is no problem if it is used for other board thickness.)● Please use the automatic mounter of automatic recognition type.
Please attach the land on the both sides.
■ Recommendedfitting land
Shaded part: Opening
■ Recommended metal mask(Recommended metal mask thickness:150μ to 200μ)
Part number φE φF
THB-□-2 3.2 5.5
THB-□-2.6 3.8 6.0
THB-□-3 4.2 6.5
THB-□-4 5.7 8.0
+0.1-0
Through hole tap [THB series]
■ Dimension
Part numberNumber of taps included in the reel
THB-1.5-2
THB-2.1-2
THB-2.6-2
THB-3.1-2
THB-3.6-2
THB-4.1-2
THB-4.6-2
THB-5.1-2
THB-5.6-2
THB-6.1-2
THB-6.6-2
THB-1.5-2.6
THB-2.1-2.6
THB-2.6-2.6
THB-3.1-2.6
THB-3.6-2.6
THB-4.1-2.6
THB-4.6-2.6
THB-5.1-2.6
THB-5.6-2.6
THB-6.1-2.6
THB-6.6-2.6
THB-1.5-3
THB-2.1-3
THB-2.6-3
THB-3.1-3
THB-3.6-3
THB-4.1-3
THB-4.6-3
THB-5.1-3
THB-5.6-3
THB-6.1-3
THB-6.6-3
THB-1.5-4
THB-2.1-4
THB-2.6-4
THB-3.1-4
THB-3.6-4
THB-4.1-4
THB-4.6-4
THB-5.1-4
THB-5.6-4
THB-6.1-4
THB-6.6-4
A
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
7.0
B
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.6
3.6
3.6
3.6
3.6
3.6
3.6
3.6
3.6
3.6
3.6
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
C D L
2.1
2.1
2.1
2.1
2.1
2.1
2.1
2.1
2.1
2.1
2.1
2.7
2.7
2.7
2.7
2.7
2.7
2.7
2.7
2.7
2.7
2.7
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
3.1
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
4.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
1.5
2.1
2.6
3.1
3.6
4.1
4.6
5.1
5.6
6.1
6.6
1.5
2.1
2.6
3.1
3.6
4.1
4.6
5.1
5.6
6.1
6.6
1.5
2.1
2.6
3.1
3.6
4.1
4.6
5.1
5.6
6.1
6.6
1.5
2.1
2.6
3.1
3.6
4.1
4.6
5.1
5.6
6.1
6.6
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
H
400pcs
400pcs
400pcs
400pcs
400pcs
400pcs
200pcs
200pcs
200pcs
200pcs
200pcs
400pcs
400pcs
400pcs
400pcs
400pcs
400pcs
200pcs
200pcs
200pcs
200pcs
200pcs
400pcs
400pcs
400pcs
400pcs
400pcs
400pcs
200pcs
200pcs
200pcs
200pcs
200pcs
350pcs
350pcs
250pcs
250pcs
200pcs
200pcs
450pcs
450pcs
300pcs
300pcs
250pcs
* The dimension H is the height between the PC board (1.6t) and the chassis.
Adsorption film
■ Condition of fitting the PC boardto the chassis
Screw
THB series
PC board 1.6t
Chassis(Threaded to the chassis)
■ To order bulk productTHB-1.5-2-B
~~
Please specify B.● 100pcs/pack● Adsorption films are not put on the bulk products.
■ Part number
■ Example of usage
Condition of fitting the PC board to thechassis
-257-
For surfacemounting
マックエイトのプリント板用端子
-258-
For surfacemounting
マックエイトのプリント板用端子
C
THB-1.5~4.1-□ 4.3
THB-4.6~6.6-□ 6.8
A B
THB-□-2 4.8 3.3
THB-□-2.6 5.3 3.9
THB-□-3 5.8 4.3
■ Dimension of the reel(THB-□-2、THB-□-2.6、THB-□-3)
■ Dimension of the reel(THB-□-4)
60φ
180φ
Dimension of the reel Dimension of the tape
X-X cross-sectionaldrawing
Y-Y cross-sectionaldrawing
X
XY Y
Dimension of the reelDimension of the tape
A-A cross-sectionaldrawing
B-B cross-sectionaldrawing
Dimension of the through hole tap reel [THB series]
Part number
THB-1.5-4THB-2.1-4THB-2.6-4THB-3.1-4THB-3.6-4THB-4.1-4THB-4.6-4THB-5.1-4THB-5.6-4THB-6.1-4THB-6.6-4
W17.517.517.517.517.517.517.517.525.525.525.5
H3.03.04.04.05.05.06.06.07.07.08.0
a178178178178178178254254254254254
F1616161616161616242424
G7.57.57.57.57.57.57.57.511.511.511.5
P1212121212121212161616
マックエイトのプリント板用端子
-259-
Through hole tap [THC-1.6 series]A chip mounter can be used for this spacer.A spacer can be fit on a PC board just by automatically loading it on the PC board and carrying out reflow.Spacer with an unloaded hole can be fit on a PC board.Tape-and-reel has an adsorption film. Please remove by pushing it from the opposite side after reflow.The jig for removing adsorption films (Part number: TH-JIG) is available.Material: BrassFinish: Tin plating over nickel baseAdaptive printed board thickness: 1.6t or over (There is no problem if it is used for other board thickness.)Please use the automatic mounter of automatic recognition type.
■ Part number
Part numberNumber of taps includedin the reel450pcs450pcs300pcs300pcs250pcs250pcs200pcs200pcs400pcs400pcs350pcs350pcs300pcs300pcs300pcs300pcs450pcs450pcs300pcs300pcs250pcs250pcs200pcs200pcs400pcs400pcs350pcs350pcs300pcs300pcs300pcs300pcs250pcs250pcs250pcs250pcs450pcs450pcs300pcs300pcs250pcs250pcs200pcs200pcs400pcs400pcs350pcs350pcs300pcs300pcs300pcs300pcs250pcs250pcs250pcs250pcs
■ DimensionAdsorption film
■ Example of usage
■ Condition of fitting to the PC board
■ Recommended fitting land
■ Recommended metal mask (Recommended metal mask thickness:150μto 200μ)
PC board
It does not protrude to the solderingface side.
FφEφ
Please attach the land on the both sides.
4-0.5
FφEφ
Shaded part: Opening
Part number φE φF
THC-1.6□-2 3.2 5.5
THC-1.6□-2.6 3.8 6.0
THC-1.6□-3 4.2 6.5
+0.1-0
■ To order bulk productTHC-1.6-□-□-B
~~
Please specify-B.● 100pcs/pack● Adsorption films are not put on theseparate products.
For surfacemounting
For surfacemounting
-260-
■バラ品御注文の場合THC-0.8-□-□-B
~~
Through hole tap [THC-0.8 series]A chip mounter can be used for this spacer.A spacer can be fit on a PC board just by automatically loading it on the PC board and carrying out reflow.Spacer with an unloaded hole can be fit on a PC board.Tape-and-reel has an adsorption film. Please remove by pushing it from the opposite side after reflow.The jig for removing adsorption films (Part number: TH-JIG) is available.Material: BrassFinish: Tin plating over nickel baseAdaptive printed board thickness: 0.8t or over (There is no problem if it is used for other board thickness.)Please use the automatic mounter of automatic recognition type.
■ Part numberNumber of taps included in the reel
Number of taps included in the reel
450pcs450pcs300pcs300pcs250pcs250pcs200pcs200pcs400pcs400pcs350pcs350pcs300pcs300pcs300pcs300pcs
450pcs450pcs300pcs300pcs250pcs250pcs200pcs200pcs400pcs400pcs350pcs350pcs300pcs300pcs300pcs300pcs250pcs250pcs250pcs250pcs
450pcs450pcs300pcs300pcs250pcs250pcs200pcs200pcs400pcs400pcs350pcs350pcs300pcs300pcs300pcs300pcs250pcs250pcs250pcs250pcs
450pcs450pcs350pcs350pcs250pcs250pcs200pcs200pcs450pcs450pcs300pcs300pcs250pcs250pcs200pcs200pcs200pcs200pcs200pcs200pcs
Part number
■ Dimension ■ Example of usageAdsorption film
■ Condition of fitting to the PC board
PC board
It does not protrude to the soldering face side.
Part number
Please specify-B.● 100pcs/pack● Adsorption films are not put on thebulk products.
Through hole tap [THC-0.8 series] specification
Please attach the land on the both sides.
■ Recommended fitting land
Shaded part: Opening
■ Recommended metal mask(Recommended metal mask thickness:150μ to 200μ)
13φ±0.5
1.75±0.1
21φ±0.8
80φ
aφ
W
Dimension of the reel
Dimension of the tape
4±0.1 2±0.1
P±0.1 1.5φ+0.10
E±0.1
H±0.1
F±0.1
G±0.3
0.4±0.05
3°
B-B cross-sectional drawing
A-A cross-sectional drawingA
AB B
■ Dimension of the reel
■ Table of dimensions
Part number φE φF
THC-0.8-□-2 3.2 5.5
THC-0.8-□-2.6 3.8 6.0
THC-0.8-□-3 4.2 6.5
THC-0.8-□-4 5.7 8.0
+0.1-0
Part number
THC-0.8-0.5-2THC-0.8-1.0-2THC-0.8-1.5-2THC-0.8-2.0-2THC-0.8-2.5-2THC-0.8-3.0-2THC-0.8-3.5-2THC-0.8-4.0-2THC-0.8-4.5-2THC-0.8-5.0-2THC-0.8-5.5-2THC-0.8-6.0-2THC-0.8-6.5-2THC-0.8-7.0-2THC-0.8-7.5-2THC-0.8-8.0-2THC-0.8-0.5-2.6THC-0.8-1.0-2.6THC-0.8-1.5-2.6THC-0.8-2.0-2.6THC-0.8-2.5-2.6THC-0.8-3.0-2.6THC-0.8-3.5-2.6THC-0.8-4.0-2.6THC-0.8-4.5-2.6THC-0.8-5.0-2.6THC-0.8-5.5-2.6THC-0.8-6.0-2.6THC-0.8-6.5-2.6THC-0.8-7.0-2.6THC-0.8-7.5-2.6THC-0.8-8.0-2.6THC-0.8-8.5-2.6THC-0.8-9.0-2.6THC-0.8-9.5-2.6THC-0.8-10-2.6THC-0.8-0.5-3THC-0.8-1.0-3
a(φ) W E GF H PReel Tape
178178178178178178178178254254254254254254254254178178178178178178178178254254254254254254254254254254254254178178
17.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.5
4.84.84.84.84.84.84.84.84.84.84.84.84.84.84.84.85.35.35.35.35.35.35.35.35.35.35.35.35.35.35.35.35.35.35.35.35.85.8
1616161616161616161616161616161616161616161616161616161616161616161616161616
7.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.5
2.22.22.82.83.83.84.84.85.85.86.86.87.87.88.88.82.22.22.82.83.83.84.84.85.85.86.86.87.87.88.88.89.89.810.810.82.22.2
1212121212121212121212121212121212121212121212121212121212121212121212121212
Part number
THC-0.8-1.5-3THC-0.8-2.0-3THC-0.8-2.5-3THC-0.8-3.0-3THC-0.8-3.5-3THC-0.8-4.0-3THC-0.8-4.5-3THC-0.8-5.0-3THC-0.8-5.5-3THC-0.8-6.0-3THC-0.8-6.5-3THC-0.8-7.0-3THC-0.8-7.5-3THC-0.8-8.0-3THC-0.8-8.5-3THC-0.8-9.0-3THC-0.8-9.5-3THC-0.8-10-3THC-0.8-0.5-4THC-0.8-1.0-4THC-0.8-1.5-4THC-0.8-2.0-4THC-0.8-2.5-4THC-0.8-3.0-4THC-0.8-3.5-4THC-0.8-4.0-4THC-0.8-4.5-4THC-0.8-5.0-4THC-0.8-5.5-4THC-0.8-6.0-4THC-0.8-6.5-4THC-0.8-7.0-4THC-0.8-7.5-4THC-0.8-8.0-4THC-0.8-8.5-4THC-0.8-9.0-4THC-0.8-9.5-4THC-0.8-10-4
a(φ) W E GF H PReel Tape
178178178178178178254254254254254254254254254254254254178178178178178178178178254254254254254254254254254254254254
17.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.517.525.525.525.525.525.525.525.525.525.525.5
5.85.85.85.85.85.85.85.85.85.85.85.85.85.85.85.85.85.87.37.37.37.37.37.37.37.37.37.37.37.37.37.37.37.37.37.37.37.3
1616161616161616161616161616161616161616161616161616161624242424242424242424
7.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.57.511.511.511.511.511.511.511.511.511.511.5
2.82.83.83.84.84.85.85.86.86.87.87.88.88.89.89.810.810.82.02.03.03.04.04.05.05.06.06.07.07.08.08.09.09.010101111
1212121212121212121212121212121212121212121212121212121216161616161616161616
-261-
For surfacemounting
マックエイトのプリント板用端子
-262-
For surfacemounting
マックエイトのプリント板用端子
H W a
THC-1.6-0.5 to 1.0 2.8 17.5 178
THC-1.6-1.5 to 2.0 3.8 17.5 178
THC-1.6-2.5 to 3.0 4.8 17.5 178
THC-1.6-3.5 to 4.0 5.8 17.5 178
THC-1.6-4.5 to 5.0 6.8 17.5 254
THC-1.6-5.5 to 6.0 7.8 17.5 254
THC-1.6-6.5 to 7.0 8.8 17.5 254
THC-1.6-7.5 to 8.0 9.8 17.5 254
THC-1.6-8.5 to 9.0 10.8 17.5 254
THC-1.6-9.5 to 10 11.8 25.5 254
E F G
2 type(0.5 to 8.0) 4.8 7.5 16
2.6 type(0.5 to 9.0) 5.3 7.5 16
3 type(0.5 to 9.0) 5.8 7.5 16
2.6 type(9.5 to 10) 5.3 11.5 24
3 type(9.5 to 10) 5.8 11.5 24
■ Dimension of the reel
Dimension of the through hole tap reel [THC-1.6 series]
13φ±0.5
21φ±0.8
Eφ±0.1
2±0.14±0.1
H±0.1
1.75±0.1
F±0.1
G±0.3
12±0.1
0.4±0.05
80φ
aφ
W
Dimension of the reel Dimension of the tape1.5φ+0.1 0
B BA
A
A-A cross-sectional drawing
B-B cross-sectional drawing
H W P F G
TH-1.6-11-M3 13.8 25.5 12 11.5 24
TH-1.6-12-M3 13.8 25.5 12 11.5 24
TH-1.6-13-M3 15.8 33.5 20 14.2 32
TH-1.6-14-M3 15.8 33.5 20 14.2 32
TH-1.6-15-M3 17.8 33.5 20 14.2 32
TH-1.6-16-M3 17.8 33.5 20 14.2 32
■Dimension of the reel
Through hole tap Dimension of the reel〔TH-1.6-11~16-M3 series〕
13φ±0.5
21φ±0.8
80φ
330φ
W
Dimension of the reel Dimension of the tape
A-A cross sectional drawing
B-B cross sectional drawing
A
A
BB
1.5φ
5.3φ±0.1
4±0.12±0.1
1.75±0.1
0.5±0.05
P±0.1
F±0.1
H±0.1
G±0.3
±0.1 0
マックエイトのプリント板用端子
● A chip mounter can be used for this spacer.● Please fit to the surface mounting board and solder by reflow.● This can be used for various purposes such as fitting a panel, fitting to a housing, andsupplying of electric wire.
● Please remove the adsorption film after reflow.● The jig for removing adsorption films (Part number: TH-JIG) is available.● Material: Brass● Finish: Tin plating over nickel base● Tap:M3 type P=0.5
M2.6 type P=0.45M2.5 type P=0.45M2 type P=0.4
●We also sell the bulk product (without adsorption film).3SSB-3.0-B 100pcs/pack
Please specify –B.
Tap M
Adsorption film
Tap M
Spacer for surface mounting [SSB series] (M3, M2.6, M2.5, M2)For automatic inserting machine
~~~
■ Example of usage
■ Recommended land diameter
Dimension of the reel Dimension of the tape
■ Instructions for use● Solder may go up to the screw part.Therefore, the screw on the PC board side may become hard by 1 to 2 threads.
● Please use it with the tightening torque or less.● Making the cream solder thickness thicker is effective for increasing the torque.
φC
Part number Package
3SSB-2.5
3SSB-3.0
3SSB-3.5
3SSB-4.0
3SSB-4.5
3SSB-5.0
2.6SSB-2.5
2.6SSB-3.0
2.6SSB-3.5
2.6SSB-4.0
2.6SSB-4.5
2.6SSB-5.0
2.5SSB-2.5
2.5SSB-3.0
2.5SSB-3.5
2.5SSB-4.0
2.5SSB-4.5
2.5SSB-5.0
2SSB-2.0
2SSB-2.5
2SSB-3.0
2SSB-3.5
2SSB-4.0
2SSB-4.5
2SSB-5.0
A4.0
4.0
4.0
4.0
4.0
4.0
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.0
3.0
3.0
3.0
3.0
3.0
3.0
L M2.5
3.0
3.5
4.0
4.5
5.0
2.5
3.0
3.5
4.0
4.5
5.0
2.5
3.0
3.5
4.0
4.5
5.0
2.0
2.5
3.0
3.5
4.0
4.5
5.0
M3
M3
M3
M3
M3
M3
M2.6
M2.6
M2.6
M2.6
M2.6
M2.6
M2.5
M2.5
M2.5
M2.5
M2.5
M2.5
M2
M2
M2
M2
M2
M2
M2
B5.0
5.0
5.0
5.0
5.0
5.0
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.0
4.0
4.0
4.0
4.0
4.0
4.0
Reel (500pcs/reel)
Reel (500pcs/reel)
Reel (400pcs/reel)
Reel (400pcs/reel)
Reel (350pcs/reel)
Reel (350pcs/reel)
Reel (500pcs/reel)
Reel (500pcs/reel)
Reel (400pcs/reel)
Reel (400pcs/reel)
Reel (350pcs/reel)
Reel (350pcs/reel)
Reel (500pcs/reel)
Reel (500pcs/reel)
Reel (400pcs/reel)
Reel (400pcs/reel)
Reel (350pcs/reel)
Reel (350pcs/reel)
Reel (500pcs/reel)
Reel (500pcs/reel)
Reel (500pcs/reel)
Reel (400pcs/reel)
Reel (400pcs/reel)
Reel (350pcs/reel)
Reel (350pcs/reel)
Cφ
When an adsorption cover is attached
■ Tightening torque
3SSB……φ5.52.6SSB…φ5.02.5SSB…φ5.02SSB……φ4.5
3SSB……3.0kg.f.cm or less2.6SSB… 3.0kg.f.cm or less2.5SSB… 3.0kg.f.cm or less2SSB……1.0kg.f.cm or less
■ Recommended creamsolder thickness
150μ to 200μH
● 3SSB-2.5 to 3.0● 2.6SSB-2.5 to 3.0
3.4● 2.5SSB-2.5 to 3.0● 2SSB-2.0 to 3.0● 3SSB-3.5 to 4.0● 2.6SSB-3.5 to 4.0
4.4● 2.5SSB-3.5 to 4.0● 2SSB-3.5 to 4.0● 3SSB-4.5 to 5.0● 2.6SSB-4.5 to 5.0
5.4● 2.5SSB-4.5 to 5.0● 3SSB-4.5 to 5.0
}}}
-263-
For surfacemounting
Mac 8’s terminals for printed boards For surface mounting (spacer)
-264-
A chip mounter can be used for this spacer.No adsorption film. Please directly adsorb.Please fit to the surface mounting board and solder by reflow.This can be used for various purposes such as fitting a panel, fitting to a housing and supplying of elctric wire.Material: BrassFinish: Tin plating over Ni base
■Recommended land diameter
■Tightening torque
For automatic inserting machine Spacer for surface mounting〔3SSF series〕(M3 type)
■Example of usage
■Part number
■Dimension of the reel
写真16
写真17
写真18Part number Package3SSF-5.53SSF-5.5-B3SSF-6.03SSF-6.0-B3SSF-6.53SSF-6.5-B3SSF-7.03SSF-7.0-B3SSF-7.53SSF-7.5-B3SSF-8.03SSF-8.0-B3SSF-8.53SSF-8.5-B3SSF-9.03SSF-9.0-B3SSF-9.53SSF-9.5-B3SSF-103SSF-10-B
A3.53.53.53.54.04.04.04.04.04.04.04.04.04.04.04.04.04.04.04.0
LReel(400pcs/reel)Bulk(100pcs/pack)Reel(350pcs/reel)Bulk(100pcs/pack)Reel(350pcs/reel)Bulk(100pcs/pack)Reel(300pcs/reel)Bulk(100pcs/pack)Reel(300pcs/reel)Bulk(100pcs/pack)Reel(300pcs/reel)Bulk(100pcs/pack)Reel(300pcs/reel)Bulk(100pcs/pack)Reel(250pcs/reel)Bulk(100pcs/pack)Reel(250pcs/reel)Bulk(100pcs/pack)Reel(250pcs/reel)Bulk(100pcs/pack)
5.8
6.8
6.8
7.8
7.8
8.8
8.8
9.8
9.8
10.8
5.55.56.06.06.56.57.07.07.57.58.08.08.58.59.09.09.59.51010
tapeH
5.5φ
3.0kg.f.cm(29.4N-cm)or less
13φ±0.5
21φ±0.8
80φ
254φ
17.5
Dimension of the reel
Dimension of the tape
4±0.1 2±0.1
12±0.1 1.5φ+0.10
5.3φ±0.1
H±0.1
7.5±0.1
16±0.3
0.4±0.05
1.75±0.1
3°
B-B cross sectionaldrawing
A-A cross sectionaldrawing
A
AB B
M3 P=0.5
4.0φ
A
L
5.0φ
0.5
For surface mounting (spacer)
For surfacemounting
Mac 8’s terminals for printed boards
マックエイトのプリント板用端子Mac 8’s terminals for printed boards For surface mounting (spacer)
● A chip mounter can be used for this spacer.● Please fit to the surface mounting board and solder by reflow.● This can be used for various purposes such as fitting of a panel, fitting to a housing, andsupplying of electric wire.
● Please remove the adsorption film after reflow.● The jig for removing adsorption films (Part number: TH-JIG) is available.● Material: Brass● Finish: Tin plating over nickel base● Tap:No 4-40 type P=0.6350
No 2-56 type P=0.4536
●We also sell the bulk product (without adsorption film).
SSB-3.0(4-40)-B 100pcs/pack
Please specify –B.
Tap M
Adsorption film
Tap M
Spacer for surface mounting [SSB series] (inch type)For automatic inserting machine
~~~
■ Example of usage
■ Recommended landdiameter
■ Tightening torque
SSB(2-56)SSB(4-40)
Dimension of the reel Dimension of the tape
SSB-□(4-40): 5.5φSSB-□(2-56): 5.0φ
SSB-□(4-40): 3.0kg.f.cm(29.4N-cm)or lessSSB-□(2-56): 3.0kg.f.cm(29.4Ncm)or less
■ Recommended creamsolder thickness
150μ to 200μH
● SSB-2.5-3.0(4-40)● SSB-2.5-3.0(2-56)● SSB-3.5-4.0(4-40)● SSB-3.5-4.0(2-56)● SSB-4.5-5.0(4-40)● SSB-4.5-5.0(2-56)
}}}
■ Instructions for use● Solder may go up to the screw part.Therefore, the screw on the PC board side may become hard by 1 to 2 threads.
● Please use it with the specified tightening torque or less.● Making the cream solder thickness thicker is effective for increasing the torque.
φC
Part number Package
SSB-2.5(4-40)
SSB-3.0(4-40)
SSB-3.5(4-40)
SSB-4.0(4-40)
SSB-4.5(4-40)
SSB-5.0(4-40)
SSB-2.5(2-56)
SSB-3.0(2-56)
SSB-3.5(2-56)
SSB-4.0(2-56)
SSB-4.5(2-56)
SSB-5.0(2-56)
A4.0
4.0
4.0
4.0
4.0
4.0
3.5
3.5
3.5
3.5
3.5
3.5
L M2.5
3.0
3.5
4.0
4.5
5.0
2.5
3.0
3.5
4.0
4.5
5.0
4-40
4-40
4-40
4-40
4-40
4-40
2-56
2-56
2-56
2-56
2-56
2-56
Reel (500pcs/reel)
Reel (500pcs/reel)
Reel (400pcs/reel)
Reel (400pcs/reel)
Reel (350pcs/reel)
Reel (350pcs/reel)
Reel (500pcs/reel)
Reel (500pcs/reel)
Reel (400pcs/reel)
Reel (400pcs/reel)
Reel (350pcs/reel)
Reel (350pcs/reel)
B5.0
5.0
5.0
5.0
5.0
5.0
4.5
4.5
4.5
4.5
4.5
4.5
Cφ
When an adsorption cover is attached
3.4
4.4
5.4
-265-
For surfacemounting