Teseo-SuitePC tool to manage, configure and evaluate

the Teseo GNSS family

Quick Training Guide

v. 1.0

Quick Start Guide - Contents 2

Introduction

Basic commands

Advanced features

Documents & related resources

1

4

3

2

Quick Start Guide - Introduction 3

Introduction1

2

3

4

Basic commands

Advanced features

Documents & related resources

Install Teseo Suite

Download and install the Teseo

Suite version selected

4

Teseo-Suite is a powerful PC Tool able to manage the ST

Teseo II and Teseo III GNSS solutions.

Teseo Suite has two flavors:

• Light available on

www.st.com (with limited

features)

• Pro on request @

st-teseo-suite-support

Install VCP Driver

ST’s Teseo II and Teseo III GNSS solutions can be connected to

a PC using the USB port through the USB-To-UART bridge

• You need to install the ST Teseo II and ST Teseo III VCP

Driver. It can be downloaded here:

• SiliconLabs www.silabs.com

or

• FTDIChip www.fdtichip.com

5

Start application

On application start-up the Configuration Session panel is shown

Push ‘Add Device’ button to add a new entry

6

1

1

2

2

Configuration Device 7

1

21

23

3

44

55

6 6

Set the Hardware type: STA8090

Set the GNSS Device Name: EVB-T3

Enable Add Control Port

Set the Protocol: NMEA

Set the Port Name: according to the

discovered on the PC

Configure the port as following table:

Click-on the Ok button

Baud rate Data Bits Stop Bits Parity Handshake

115200 bps 8 Bits 1 Bit none none

7

7

Connect the device

In the Configuration Session panel a new entry (row) is shown

Enable Connect Ctrl port

Click-on the Connect all button

8

1

2

12

3

3

Inspect Device 9

2

2

3

3

Click-on View Monitor button in the menu-bar

NMEA Decoding panel is shown

NMEA Stream can be viewed and inspected

1

1

Disconnect the device

In the Configuration Session panel entry (row)

Click-on the Disconnect button

10

1

2

21

Quick Start Guide - Contents 11

Basic commands

1

2

3

4 Documents & related resources

Advanced features

Introduction

Basic commands - Contents 12

1

2

3

4

Send Commands

Map View

Signal Level

Filter the message list

5

6

Recod a NMEA Log

Play a NMEA Log

Send commands 13

2

3

2 3

4

4

1 In the ‘Nmea Decoding’ panel

Write the ‘command’ in the text-edit entry

Click-on the ‘Send’ button to raise the command to the device

Inspect the replay message in the NMEA Stream

1

Filter the message list 14

1 In the ‘Nmea Decoding’ panel

Select the messages you want

Refresh the new message-list into the device

1

2

2

3

3

Map view 15

1 Click-on ‘Map View’ button in the menu

Inspect the position in the ‘Map View’ panel2

2

1

Signal Levels 16

1 Click-on ‘Signal Level View’ button in the menu

The ‘Signal level’ panel reports all the details for all the seen satellites

1

2

2

Record a NMEA Log session 17

1 To start log session, click-on ‘Start/Stop Record Control Port’ button

in the menu (button turns red)

2 To stop a log session, click-on ‘Start/Stop Record Control Port’ button

in the menu (button turns white)

1

2

Play a NMEA Log session [1/4] 18

1 Click-on ‘Player’ button in the menu (the Logfile Toolbar panel will appear)

Click-on ‘Play’ button in the Logfile Toolbar (the ‘Open’ dialog will appear)2

1

2

Play a NMEA Log session [2/4] 19

1 In the ‘Open’ dialog select the log to play

Click-on ‘Open’2

1

2

Play a NMEA Log session [3/4] 20

2

3

2

3

1

1 In the ‘Select the NMEA payload’ folder based on the GNSS IC used

In the ‘ConfigPayloadNMEA.xml’ file

Push ‘Open’

Play a NMEA Log session [4/4] 21

1 In the Logfile Toolbar panel all the buttons are enabled and you can

start, stop, rewind the log as a standard tape

1

Quick Start Guide - Contents 22

Advanced Features

Introduction

Basic commands

Documents & related resources

1

3

2

4

Advanced features - Contents 23

Update Boot and GNSSLib1

Update GNSSLib only 2

Firmware configuration3

Update Bootloader and GNSSLib 24Teseo Suite Pro

ONLY

1

1 Open Teseo II (T2) or Teseo III (T3) X-Loader from menu

2 Select the binary file from file-system

2

3 Select COM Port and the baud-rate

3

4 Click-on Start to update

4

Update GNSS-Lib 25

1

1 Open Firmware Upgrade tool

2 Select the binary file from file-system

2

3 Select COM Port and the baud-rates

3

4 Click-on Start to update the GNSS-Lib

4

Firmware configuration [1/2] 26

1

1 Select ‘FW Configuration panel’ in the menu

Select the target to be configured (Connected device in the example)

Click-on Ok

2

2

3

3

Teseo Suite Pro

ONLY

Firmware configuration [2/2] 27

1

1 Expand the CDB-ID number under configuration

2 Select the specified field under configuration

2

3 Enable the field and/or set the right value (Galileo constellation is enabled

in the example)

4

3

4 Apply the change to the device

Teseo Suite Pro

ONLY

Quick Start Guide - Contents 28

Documents & related resources

Introduction1

Basic commands2

Advanced features3

4

Documents & related resources

• Teseo II: Webpage

• Data-sheet of all PNs;

• Teseo III: Webpage

• Data-sheet of all PNs;

• Teseo Suite: Webpage• Datasheet

• Install program

29

11/24/2017

All documents are available on:

www.st.com

Teseo Suite – Extra features

Push Help menu to access User-Manual

User-Manual reports all information needed

30

1

2

1

2

Enjoy GNSS solution development

with Teseo-Suite

Now you can develop your GNSS solution with ST Teseo II, ST Teseo

III and ST Teseo Module, using Teseo-Suite to explore all the

available features

31