Products Solutions ServicesTI00026S/04/EN/18.1571279737

Technical InformationWirelessHART Adapter SWA70

Smart WirelessHART interface module with power supply for field devices

Application

The WirelessHART Adapter SWA70 is an interface module for the wireless transmission of 4 to 20 mA/HART signals from connected field devices to a WirelessHART Fieldgate. It is powered by either a battery pack or power supply units. The WirelessHART Adapter can be used in hazardous and non-hazardous area for applications, such as:

• Process optimization:By connecting the WirelessHART Adapter, it is possible to monitor and optimize plant sections with less cost and effort.

• Level monitoring in tanks and silos:Measured values together with the device and battery status are transmitted at regular intervals to a higher-level system.

• Plant condition monitoring:Wireless devices are mounted at critical points in the plant which are not normally connected to the control room due to their limited accessibility or wiring costs. Improved data flow and diagnostics increase plant reliability and safety.

Your benefits

The flexible adapter concept offers the following advantages:

• HART devices are quickly upgraded to WirelessHART technology• Fast integration of 4 to 20 mA field devices into a WirelessHART network• One 4 to 20 mA field device and up to four HART field devices in multidrop mode can

be connected to a WirelessHART Adapter• Burst mode and event notification supported• Remote and difficult-to-access HART devices are connected to the control room

without expensive cabling • Easy planning, quick installation and integration

WirelessHART Adapter SWA70

2

Function and system designWirelessHART WirelessHART adds wireless capabilities to the HART protocol, while ensuring compatibility with

existing HART devices, commands and tools.A WirelessHART network comprises:

• Wireless field devices• Wired field devices with a connected WirelessHART Adapter• Gateways responsible for communication between devices and host applications• Network and Safety Manager responsible for configuring, managing and monitoring the network

WirelessHART Adapter SWA70

The WirelessHART Adapter SWA70 acts as an add-on interface for wireless communication with HART field devices or 4 to 20 mA field devices.It is powered by either a battery pack, a wide range power unit or a DC power unit. The DC power unit can use solar power, for example. A special long-life, high-power battery is used as the battery.

The WirelessHART Adapter SWA70 supports the following functions:

• Power supply for a HART field device or a 4 to 20 mA field device• Power supply of up to four HART devices in the multidrop mode with a wide range power unit• Connection of up to four externally powered HART field devices in the multidrop mode• Scaling of the current signal from a connected 4 to 20 mA field device• Burst mode and event notification for the WirelessHART Adapter and the connected field devices

System design The WirelessHART Adapter SWA70 transmits information to a host application via a WirelessHART Fieldgate. The figure below shows a typical WirelessHART network architecture.

Ethernet

WirelessHART Adapter SWA70

3

Inputs (wired interface)Inputs

Communication interface HART interface to configure the WirelessHART Adapter with a HART modem

Protocol version HART Version 7.3 (backwards compatible with earlier HART versions)

Transmission rate 1200 bits/s

Field device power supply

Terminals The WirelessHART Adapter has a terminal block with screw terminals 1-6 and 2 eyelets 7 and 8 for connection purposes.

One input channel for: • One point-to-point connection with a HART field device or• One point-to-point connection with a 4-20 mA field device or• Up to four HART field devices connected in multidrop mode if a wide

range power unit is used. The wide range power unit provides 24 V to power the field devices.

Current: 4 to 20 mA (according to NAMUR recommendation NE 43) or 4 mA if only one field device is connected in multidrop mode

Error current: I3.6 mA or I 21 mAProtection: Short-circuit protection, triggered if currents > 25 mATerminal voltage: 8 to 23 V DC, configurable

Application Terminal assignment

Remarks Connection values

Power supply to a loop-powered field device

1 (+) and 2 (–) • Current measurement and HART communica-tion where applicable

• Loop current flows through the adapter

• 4 to 20 mA (according to NAMUR NE43)

• 8-23 V power supply for field device, configurable, see the following diagram

• Integrated load: 250 Ohm for non-Ex versions and 360 Ohm for Ex versions

Integration of the WirelessHART Adapter into a current loop

2 (+) and 3 (–) • Current measurement and HART communica-tion where applicable

• Loop current flows through the adapter

• 4 to 20 mA (according to NAMUR NE43)

• Integrated load: 250 Ohm for non-Ex versions and 360 Ohm for Ex versions

Integration of the WirelessHART Adapter into a current loop

5 and 6 • Integration into HART communication

• Loop current does not flow through the adapter

• Input impedance for HART communication: > 5 kOhm at 1700 Hz

• DC input impedance: 1 MOhmConfiguration of the WirelessHART Adapter with a HART modem

7 and 8 Temporary connection of the modem via eyelets

• Input impedance for HART communication: > 5 kOhm at 1700 Hz

• DC input impedance: > 1 MOhm

1 2 3 4 5 6

HART communication

87

Loop current measurement and HART communication

Loop current measurement 1 – 2

Loop current measurement 2 – 3

WirelessHART Adapter SWA70

4

Field device power supply through SWA70

Output (wireless interface)Communication interface WirelessHART communication interface (IEC 62591),

HART version 7.3 (backwards compatible with earlier HART versions)

Transmission rate Nominal 250 kBits/s

Operating frequency 2.4 GHz (ISM band)

Range Up to 250 m outdoors, up to 50 m indoors

Transmission power Can be configured for 0 dBm or 10 dBm to adapt to national regulations

Device variables Up to 10 bursts can be configured in accordance with the HART specification. Up to eight device variables per burst can be configured depending on user transmission requirements.

Example:• HART field device: device variables• 4 to 20 mA field device: scaled or linearized process values• WirelessHART Adapter: scaled loop current and other variables, choose from: estimated battery

life, battery voltage, energy used, adapter temperature

Additional functions • Event notification, configurable for up to eight variables from the WirelessHART adapter and/or connected field devices

• Error notification and scaling or linearization of the 4 to 20 mA signal of the connected analog field device

• Monitoring of energy consumption• Locking of device parameterization

Diagnostics Diagnostics function in accordance with NAMUR NE 107, ASM and HART recommendations

1 SWA70 non-Ex versions with 4 to 20 mA field device2 SWA70 non-Ex versions with HART field device3 SWA70 Ex versions with HART field device or 4 to 20 mA field device

12

14

16

18

20

22

24

Field device power supply [V]

Loop current [mA]

0 4 8 12 16 20

1

2

3

WirelessHART Adapter SWA70

5

Power supplyVersions • Battery unit: special long-life high-power lithium-thionyl chloride battery unit

• Wide range power unit• DC power unit, e.g. solar-powered

Power supply • Wide range power unit: 24 V to 230 V AC/DC ± 10 %, 50/60 Hz• DC power unit: 8 to 50 V DCIn the event of an external power supply failure, wireless communication is maintained for at least one hour thanks to an internal power supply system.

Current consumption • Wide range power unit: <350 mA, 1 A slow-blow back-up fuse must be installed by the customer onsite

• DC power unit: < 250 mA, 1 A slow-blow back-up fuse must be installed by the customer onsite

Power consumption • Wide range power unit: max. active power 7 W / max. reactive power 12 VA with alternating voltage• DC power unit: < 2.2 W

Battery capacity • 19 Ah nominal capacity at 20 °C• 7.2 V DC

Battery life Up to 10 years, depending on update rate of process variables, field device type and environmental conditions

Cable Field device connection• Mounted directly on field devices: cable supplied (0.25 mm2)• Remote mounting: standard installation cable (0.25 mm2)

Wide range power unit or DC power unit (M12 socket): 0.75 mm2

Performance characteristicsReference operating conditions

According to IEC 61298 Part 2

Maximum measured error 4 to 20 mA circuit: 0.125 % of measuring range

Influence of ambient temperature

4 to 20 mA circuit: 5 μA/10 K

Operating conditionsInstallation conditions

Installation • Directly on field device• Remotely on a wall or pipe using optional mounting bracket

Installation instructions (recommendations)

• Consider the range. See Seite 4, Range.• Avoid mounting too near walls, pipes and heavy-duty electrical equipment.• Mount in line of sight with a neighboring adapter and Fieldgate. • Consider the development of the Fresnel zone.• Align antenna so that it is completely vertical.

WirelessHART Adapter SWA70

6

Protection against lightning • Do not mount the WirelessHART Adapter at the highest point in the plant.• WirelessHART Adapter with metal housing: connect protective ground to protective ground

connection of the housing. Protective ground in 2.5 mm2.

Environment

Climate class EN 60721-3-4: 4K4H, suitable for stationary use at unprotected outdoor locations

Ambient temperature range • –40 to +80 °C (–40 to +176 °F)• Ex versions –40 to +60 °C (–40 to +146 °F)• The battery pack capacity decreases significantly at temperatures below –30 °C (–22 °F).

Storage temperature • WirelessHART Adapter without battery unit: –40 to +85 °C (–40 to +185 °F)• WirelessHART Adapter with disconnected battery unit: –40 to +25 °C (–40 to +77 °F)• Battery unit: –40 to +25 °C (–40 to +77 °F)

Vibration resistance EN 60068-2-64: 20 Hz f 2000 Hz: 0.01 g²/Hz

Shock resistance EN 60068-2-27: 15 g, 11 ms

Electromagnetic compatibility

All modules are suitable for industrial use and meet the requirements of EU Directive 2004/108/EU "Electromagnetic compatibility":

• Interference emission:• With wide range power unit: EN 61326-1: 2013, Class A• With DC power unit or battery unit: EN 61326-1: 2013, Class B

• Interference immunity:• EN 61326-1: 2013 Tab. 2 (industry)• Namur recommendation EMC (NE21) for terminals 1 to 3

Temperature restrictionsThe temperature restrictions listed are based on the assumption that more than 30% battery capacity is remaining.

Ex version, 4 to 20 mA supply mode

The application range is limited in the event of high measuring currents close to 22 mA.

Current strengthin mA4 22

Term

inal

vol

tage

of

field

dev

ice

in V

8 –40°C –30°C10 –40°C –30°C12 –40°C –30°C14 –40°C –25°C16 –40°C –25°C18 –40°C20 –40°C22 –40°C

WirelessHART Adapter SWA70

7

Ex version with fixed current of 4 mA (multidrop mode)

Non-Ex version,4 to 20 mA supply mode

The application range is limited in the event of high measuring currents close to 22 mA.

Non-Ex version with fixed current of 4 mA(multidrop mode)

Start-up current in mASee Operating Instructions, "Field device power supply" section.4 6 8 10 12 14 16 18 20 22

Term

inal

vol

tage

of

field

dev

ice

in V

8 –40°C –40°C –40°C –40°C –40°C –40°C –40°C –35°C –25°C –15°C10 –40°C –40°C –40°C –40°C –40°C –40°C –40°C –30°C –15°C –10°C12 –40°C –40°C –40°C –40°C –40°C –40°C –35°C –20°C14 –40°C –40°C –40°C –40°C –40°C –35°C –25°C –10°C16 –40°C –40°C –40°C –40°C –40°C –25°C18 –40°C –40°C –40°C –30°C –5°C20 –40°C –35°C22

Current strengthin mA4 22

Term

inal

vol

tage

of

field

dev

ice

in V

8 –40°C –30°C10 –40°C –30°C12 –40°C –30°C14 –40°C –25°C16 –40°C –25°C18 –40°C20 –40°C22 –40°C

Start-up current in mASee Operating Instructions, "Field device power supply" section.4 6 8 10 12 14 16 18 20 22

Term

inal

vol

tage

of

field

dev

ice

in V

8 –40°C –40°C –40°C –40°C –40°C –40°C –40°C –40°C –40°C –40°C10 –40°C –40°C –40°C –40°C –40°C –40°C –40°C –40°C –40°C –35°C12 –40°C –40°C –40°C –40°C –40°C –40°C –40°C –40°C –40°C –35°C14 –40°C –40°C –40°C –40°C –40°C –40°C –40°C –35°C –35°C –35°C16 –40°C –40°C –40°C –40°C –40°C –40°C –40°C –35°C –20°C18 –40°C –40°C –40°C –40°C –40°C –40°C –40°C –35°C20 –40°C –40°C –40°C –40°C –40°C –35°C22 –40°C –40°C –40°C

WirelessHART Adapter SWA70

8

Mechanical constructionDesign/dimensions

Weight • Polyester housing with power supply unit: 0.785 kg• Aluminum housing with power supply unit: 0.9 kg

Materials • Housing: polyester or aluminum, see ordering information• Color of polyester and aluminum: light-gray, RAL 7035 with blue logo

Degree of protection • Polyester housing F32: IP65/IP66; NEMA Type 4• Aluminum housing F33: IP67, NEMA Type 4X

Connection adapters M20x1.5 to M20x1.5; M20x1.5 to G 1/2; M20x1.5 to NPT 1/2; M20x1.5 to NPT 3/4See ordering information

Antenna Omnidirectional dipole antenna

189.

9

26.192

111.5

Dimensions in mm25.4 mm = 1 inch

32.1 24

.9

184.

4

139.

7

21.9

92.8

89.5

Cable entry fordirect installation,

internal threadM20x1.5

Cable entry forremote installation,

internal thread M20x1.5

WirelessHART Adapter SWA70

9

OperationConfiguration • Local configuration with FieldCare or DeviceCare via modem and DTM for SWA70

• Local operation with FieldXpert also in the hazardous area• Remote configuration with FieldCare via WirelessHART Fieldgate SWG70 and DTM for SWA70 and

SWG70• Remote configuration with a software and a gateway based on the device description (DTM or DD)

Display and operating elements

Display and operating elements in WirelessHART Adapter:• Push buttons for selecting various functions• LEDs for indicating communication status, battery status, voltage level and error messages

Device address Can be configured between 0 to 63 via DD or DTM, default address 15

Ordering informationProduct structure Detailed information about the product structure is available:

• In the Product Configurator on the Endress+Hauser website: www.endress.com Enter "SWA70" as the search string click the "WirelessHART Adapter SWA70" link In the window on the right under "Device support", click the link "Configure your selected product"

• From your Endress+Hauser Sales Center: www.addresses.endress.com

DocumentationWirelessHART Adapter SWA70

Certificates and approvalsCE mark The WirelessHART Adapter SWA70 meets the legal requirements of the relevant EU Directives.

Endress+Hauser confirms successful testing of the WirelessHART Adapter SWA70 by affixing to it the CE mark.

Ex approval See "Documentation" section.

WirelessHART Adapter SWA70Operating Instructions BA00061S

WirelessHART solutionsfor real-world applicationsCompetence brochure CP00013S

WirelessHART Adapter SWA70Safety Instructions ATEX, IECEx XA00506F

WirelessHART Fieldgate SWG70Operating Instructions BA00064S

WirelessHART Adapter SWA70Safety Instructions CSA XA00538F

WirelessHART Adapter SWA70

10

Radio approvalsEurope This device meets the requirements of the EC Telecommunications Directive 1999/5/EC

(R&TTE approval).

USA and Canada This device complies with part 15 of the FCC Rules.

China ProductsoSturlduittnuevlnTtculuThatulaav slIuihuTrtufmmWuHfTlTtumlco umteAIlT vhuW RRoddo nu wupyumyuWronl70uW422Pu2/ugF../bkzF-

Brazil ANATEL 2759-11-7311 (EAN Number: 7898994191421)“Este produto está homologado pela ANATEL, de acordo com os procedimentos regulamentados pela Resolução 242/2000, e atende aos requisitos técnicos aplicados.”

Japan This device has been granted a designation number by the Japanese Ministry of Internal Affairs and Communications according to the Ordinance concerning Technical Regulations Conformity Certification etc. of Specified Radio Equipment (

)

• Article 2 clause 1 item 19• Approval n°: 202WW09117711

This device should not be modified (otherwise the granted designation number will be invalid).

Mexico COFETEL RCEPNSW12-0650La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada.

Other approvals Other national approvals are available on request

R

WirelessHART Adapter SWA70

11

WirelessHART Adapter SWA70

www.addresses.endress.com