Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door...

62
Technical Information Prime Paint Data ......................................................... 11-002 Colorstyle Paint Data ................................................... 11-003 Asphaltic Frame Undercoating....................................... 11-004 Frame, Door Opening Sizes and Hardware Provisions 1-3/8” Door – Single and Double................................... 11-101 Hardware Locations – Standard 1-3/8” Door ................... 11-102 1-3/4” Door – Single and Double................................... 11-103 Hardware Locations – Standard 1-3/4” Door 6-8, 7-0, 7-2 High, 4-1/2” or 5” High Hinge ............... 11-104 7-10, 8-0, 9-0, 10-0 High, 4-1/2” or 5” High Hinge ..... 11-104A 5-0 thru 10-0 ......................................................... 11-104B, 11-104C 6-8, 7-0, 7-2, 8-0 High, Dutch, 4-1/2” or 5” High Hinge.... 11-104D Hardware Locations – Optional (NAAMM) 1-3/4” Door 6-8, 7-0, 7-2 High, 4-1/2” High Hinge ....................... 11-105 7-10, 8-0, 9-0, 10-0 High, 4-1/2” High Hinge............. 11-105A 6-8, 7-0, 7-2 High, 5” High Hinge ............................. 11-106 7-10, 8-0, 9-0, 10-0 High, 5” High Hinge................... 11-106A 1-3/8” Door Frames, Hinge and Strike Preparations......... 11-201 1-3/4” Door Frames, 4-1/2” and 5” Hinge Preparations .... 11-202 1-3/4” Door Frames, ANSI (4-7/8”) Strike Preparations ... 11-203 1-3/4” Door Frames, Cylindrical Strike Preparation .......... 11-204 Series SQW Weatherstrip Kerf Frame Hinge Preparation... 11-205 Series SQW Weatherstrip Kerf Frame Strike Preparation .. 11-206 Full Depth Hinge Reinforcement .................................... 11-207 High Frequency Hinge Preparation................................. 11-208 1-3/8” and 1-3/4” Door Frame Mute Application.............. 11-209 Reversible Flush Bolt Preparation .................................. 11-210 Frame Construction Double Rabbet Frames, Die-cut, Welded Corner For Future Use ............................................................ 11-301 Assembly T-2, T-3 ....................................................... 11-302 Assembly V-2 ............................................................. 11-303 Assembly V-3 ............................................................. 11-304 Assembly V-5 ............................................................. 11-305 Assembly V-7 ............................................................. 11-306 Assembly V-8, V-9 ...................................................... 11-307 Hospital Stops ............................................................ 11-308

Transcript of Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door...

Page 1: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the

Technical Information Prime Paint Data ......................................................... 11-002 Colorstyle Paint Data ................................................... 11-003 Asphaltic Frame Undercoating ....................................... 11-004 Frame, Door Opening Sizes and Hardware Provisions 1-3/8” Door – Single and Double................................... 11-101 Hardware Locations – Standard 1-3/8” Door ................... 11-102 1-3/4” Door – Single and Double................................... 11-103 Hardware Locations – Standard 1-3/4” Door 6-8, 7-0, 7-2 High, 4-1/2” or 5” High Hinge ............... 11-104 7-10, 8-0, 9-0, 10-0 High, 4-1/2” or 5” High Hinge ..... 11-104A 5-0 thru 10-0 ......................................................... 11-104B, 11-104C 6-8, 7-0, 7-2, 8-0 High, Dutch, 4-1/2” or 5” High Hinge .... 11-104D Hardware Locations – Optional (NAAMM) 1-3/4” Door 6-8, 7-0, 7-2 High, 4-1/2” High Hinge ....................... 11-105 7-10, 8-0, 9-0, 10-0 High, 4-1/2” High Hinge............. 11-105A 6-8, 7-0, 7-2 High, 5” High Hinge ............................. 11-106 7-10, 8-0, 9-0, 10-0 High, 5” High Hinge ................... 11-106A 1-3/8” Door Frames, Hinge and Strike Preparations ......... 11-201 1-3/4” Door Frames, 4-1/2” and 5” Hinge Preparations .... 11-202 1-3/4” Door Frames, ANSI (4-7/8”) Strike Preparations ... 11-203 1-3/4” Door Frames, Cylindrical Strike Preparation .......... 11-204 Series SQW Weatherstrip Kerf Frame Hinge Preparation... 11-205 Series SQW Weatherstrip Kerf Frame Strike Preparation .. 11-206 Full Depth Hinge Reinforcement .................................... 11-207 High Frequency Hinge Preparation ................................. 11-208 1-3/8” and 1-3/4” Door Frame Mute Application .............. 11-209 Reversible Flush Bolt Preparation .................................. 11-210

Frame Construction Double Rabbet Frames, Die-cut, Welded Corner For Future Use ............................................................ 11-301 Assembly T-2, T-3 ....................................................... 11-302 Assembly V-2 ............................................................. 11-303 Assembly V-3 ............................................................. 11-304 Assembly V-5 ............................................................. 11-305 Assembly V-7 ............................................................. 11-306 Assembly V-8, V-9 ...................................................... 11-307 Hospital Stops ............................................................ 11-308

Page 2: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the

Hardware Reinforcements Closer Reinforcements, Plate Type .................................. 11-401, 11-402 Closer Reinforcements, Sleeve Type ........................................... 11-403 Frame Anchors Anchor Quantity ...................................................................... 11-500 Snap-In Stock Metal and Wood Stud Anchors ............................... 11-501 Recessed Welded Wood Stud Anchor .......................................... 11-502 Flush Welded Wood Stud Anchor ................................................ 11-503 Snap-In Adjustable Jamb Anchor for Wood Stud Walls .................. 11-504 Snap-In Adjustable Before Drywall Stud Anchor ........................... 11-505 Recessed Welded Metal Stud Anchor........................................... 11-506 Flush Welded Metal Stud Anchor ................................................ 11-507 Wire Masonry and Masonry “T” Anchors (Loose) ........................... 11-508 Yoke and Strap Masonry / Existing Opening Pipe and Plate Anchor .. 11-509 Welded Existing Wall Anchor .................................................... 11-509A Snap-In Existing Opening Butterfly Jamb Anchor .......................... 11-510 Welded Existing Opening Anchor for Standard and Special Faces .... 11-511 Welded Floor Anchor ................................................................ 11-512 Welded Adjustable Floor Anchor ................................................. 11-513 Sidelite Floor Anchor / Bracing Strap / Closure Clip ....................... 11-514 Frame Spline ........................................................................... 11-515 Fire Rated Weld to Building Structure Installation Instructions ........ 11-516 Special Information Standard Frame Installation ........................................... 11-901, 11-902 Existing Wall Frame Installation ...................................... 11-903, 11-903A Frame Spreader Bars ............................................................... 11-904 Hospital/Sanitary Stop .............................................................. 11-905

Page 3: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the

Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the steel. This treatment removes mill-contaminants. The phosphoric acid etching of the steel provides excellent primer adhesion. The phosphate coating also provides corrosion protection. After the wash, the frame pieces are dried and then painted with a neutral-color primer. Application is by means of spray or by immersion in a dip tank. The frame pieces are then oven dried. The primer coating provides protection against rust and exhibits excellent adhesion characteristics. This primer is an environmentally friendly water-base paint that contains no heavy metal pigments and meets air quality guidelines. The primer coating is intended as a preparatory base for necessary field painting. Standard primer color: Gray

PERFORMANCE DATA: Primer-painted steel surfaces have been subjected to the following tests: Salt Spray: Test specimens were subjected to 120 continuous hours of salt spray, in compliance with ASTM B117, “Method of Salt Spray (Fog) Testing”. The test specimens were scribed with an “X” per ASTM D1654, sections 4.1 and 5.1. Humidity: Test specimens were subjected to humidity (condensation) testing for a period of 240 continuous hours, at a minimum temperature of 100° Fahrenheit, as specified in ASTM D4585, “Standard Practice for Testing Water Resistance of Coatings Using Controlled Condensation.” Impact: At a room temperature of 70° to 75° Fahrenheit, test specimens were subjected to a direct impact of 20 inch pounds using the Gardner Impact Tester with a 1/2” diameter ball or punch. Following the test, a strip of 3/4" wide #600 Scotch® cellophane tape was applied to the impact area and pulled off sharply. Test was conducted in compliance with ASTM D2794. “Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact).” Film Adhesion: The prime paint on test specimens was subjected to a cross cut test utilizing 11 parallel cuts located 1mm apart, made by a sharp instrument. Cuts were made both vertically and horizontally to form a grid. A strip of 1” wide pressure sensitive tape was applied to the scribed surface and removed rapidly. Paint adhesion was tested in compliance with test protocol “B” as defined by ASTM D3359, “Standard Test Method for Measuring Adhesion by Tape Test.” Primer paint meets the requirements for acceptance stated in the current version of ANSI Standard A250.10 (previously A224.1), “Test Procedure and Acceptance Criteria for Prime Painted Steel Surfaces”.

Page 4: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the

Process Data Factory-applied PPG Spectracron® colorstyle finish is a two-part, urethane top-coat that is electrostatically applied over the standard primer. The paint is then oven cured. The chemically reactive cure provides a top quality, abrasion resistant finish with excellent weathering characteristics. This finish is environmentally friendly in that it does not contain heavy metal pigments. All KD colorstyle frame units are component poly-bagged and are boxed together. Individual components are poly-bagged and cardboard wrapped to guard against abrasion and impact during handling. Welded 3 sided frames are wrapped in plastic and surrounded with cardboard to resist abrasion and impact.

60° Gardner Gloss: 15 to 20 Colors: 192 standard colors to choose from. Color selection guides are available upon request. To order your free RAL Classic Color Deck, call your Ceco Door customer service professional.

Performance Data: Colorstyle, factory applied finish paint process has been subjected to the following test:

Salt Spray, Humidity, Accelerated Weathering, Impact, Film Adhesion & Abrasion

Factory applied colorstyle finish paint meets the performance requirements and acceptance criteria as stated in ANSI Standard A250.3, “Test Procedure and Acceptance criteria for Factory Applied Finish Painted Steel Surfaces…”.

Compliance with LEED EQ 4.1 and 4.2 for jobsite VOC levels. HAPs (Hazardous Air Pollutants) free. Field Painting A finish coat of paint is to be applied to prime painted units by the painting contractor. The topcoat of paint used over the primer plays a very important role in extending the life of a steel frame. Any paint used must be compatible with steel. Solvent base finish paints are recommended for application over the factory applied primer. If solvent base finish paints cannot be used, it is important that a water-base primer formulated for steel to be applied over the factory primer. This should be done before applying water-base top coats, to prevent flash rusting. We do not recommend the use of water based finish paints such as latex, acrylic, poly-vinyl acetate emulsion finishes.

Gloss Show-through characteristics of finish increase as the paint gloss increases. To minimize this, a maximum paint gloss rating of 20% reflectance, measured using a 60° gloss meter is recommended. This should be suitable for most applications. ranslucent paints may emphasize show-through and their use is not recommended.

Page 5: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 6: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 7: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 8: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 9: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 10: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 11: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 12: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 13: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 14: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 15: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 16: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 17: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 18: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 19: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 20: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 21: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 22: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 23: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 24: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 25: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 26: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 27: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 28: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 29: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 30: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 31: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 32: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 33: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 34: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 35: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 36: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 37: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 38: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 39: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 40: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 41: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 42: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 43: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 44: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 45: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 46: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 47: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 48: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 49: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 50: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the

Distributor Tech-Data

EXISTING OPENING BUTTERFLY JAMB ANCHOR

11-510

12/10/19

Page 51: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 52: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 53: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the

Distributor Tech-Data

OPTIONAL - ADJUSTABLE FLOOR ANCHOR

11-513

11/04/19

FOR USE WHEN FLOORS ARE NOT LEVEL

Page 54: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 55: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 56: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 57: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 58: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 59: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 60: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 61: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the
Page 62: Technical Information Frame, Door Opening Sizes and Hardware ….pdf · Process Data Steel door frame pieces are processed through a phosphoric acid wash to clean and pre-treat the