Taps
-
Upload
angelochintu -
Category
Documents
-
view
266 -
download
4
Transcript of Taps
CONTENTSPage No.
Screwing Taps - Nomenclature 190Hand and Short Machine Screwing Taps (Metric Coarse & Fine Pitch) 191sizes up to & inclu . 10 mmHand and Short Machine Screwing Taps (Metric Coarse Pitch) 192Hand and Short Machine Screwing Taps (Metric Fine Pitch) 193Hand Taps - BSW Form 196Hand Taps - BSF Form 197Hand Taps - UNC Form 198Hand Taps - UNF Form 199Hand Taps - BSCY Form 200Hand Taps - BS Conduit Form 201Hand Taps - BSP (Parallel) 202Hand Taps - BSP (Parallel) 'G' Series 203Hand Taps - BSP (Taper) Form (RC Series) 204Hand Taps - NPT 205Long Shank Machine Screwing Taps (Metric Coarse Pitch) 206Long Shank Machine Screwing Taps (Metric Fine Pitch) 207Nut Screwing Taps (Metric Coarse Pitch) 209Nut Taps - BSW Form 210Nut Taps - BSF Form 211Nut Taps - UNC Form 212Nut Taps - UNF Form 213Hand Taps to DIN 352 214Hand Taps to DIN 2181 215
Core Dia.Size ofSquare
Length ofSquare
Majordia.
Chamfer Relief
Shank dia. —'
Thread Lead Angle
Pitch dia..—
Cutting Edge
No Relief
Concentric
Heel
ConcentricMargin
Con-eccentricRelief
NegativeRake Angle
90 deg.
Radius
TangentialMeasurement
Hook Angle(chordal Measurement)
NegativeRake
radial PositiveRake
Hook
Back 190
TABLE I : ISO Metric Screw Threads Coarse Pitch TABLE II : ISO Metric Screw Threads Fine Pitch
NominalDiameter
3.04.04.55.06.07.08.09.0
10.0
Pitch Pitch
0.500.700.750.801.001.001.251.251.50
ThreadLength
111313161919222224
OverallLength
485353586666727280
ShankDia
3.154.004.505.006.307.108.009.00
10.00
SquareSize
2.503.153.554.005.005.606.307.108.00
NominalDiameter
4.04.55.05.56.07.08.08.09.09.0
10.010.010.0
0.500.500.500.500.750.750.751.000.751.000.751.001.25
ThreadLength
13131617191916191619172020
Overal lLength
53535862666666696669737676
ShankDia
4.04.55.05.66.37.18.08.09.09.0
10.010.010.0
SquareSize
3.153.554.004.505.005.606.306.307.107.108.008.008.00
Manufactured with straight flutes and a shank with square for driving,
1)
2)
Back
Unless otherwise specified, the Screwing taps shall be supplied with toleranceclass '6H', non-serial and with Straight flutes.
Usually supplied in sets consisting of three taps, viz. Taper, Second and Bottomingfor Coarse Pitch and Taper and Bottoming for Fine Pitch
191
High Speed SteelGROUND THREAD HAND AND SHORT
MACHINE SCREWING TAPSFor ISO Metric Screw Threads
Specifications conform toIS 6175 : Part 2 : 1992
Dimensions in mm
1) Unless otherwise specified, the Screwing taps shall be supplied with tolerance class '6H',Non-Serial and with Straight flutes.
2) Usually supplied in sets consisting of three taps viz, Taper, Second and Bottoming.
Back 192
NominalDiameter
1112141618202224273033
Pitch
1.501.752.002.002.502.502.503.003.003.503.50
ThreadLength
2529303237373845454851
OverallLength
858995
102112112118130135138151
ShankDia
8.09.0
11.212.514.014.016.018.020.020.022.4
SquareSize
6.37.19.0
10.011.211.212.514.016.016.018.0
NominalDiameter
36394245485256606468
Pitch
4.004.004.504.505.005.005.505.506.006.00
ThreadLength
57606067677070767979
OverallLength
162170170187187200200221224234
ShankDia
25.028.028.031.531.535.535.540.040.045.0
SquareSize
20.022.422.425.025.028.028.031.531.535.5
High Speed SteelGROUND THREAD HAND AND SHORT
MACHINE SCREWING TAPSFor ISO Metric Coarse Pitch Threads
Specifications conform toIS 6175 : Part 3 : 1992
Dimensions in mm
Manufactured with straight flutes and a shank with square for driving.
Back 193
NominalDiameter
11111212121414141515161617171818182020202222
Pitch
0.751.001.001.251.501.001.251.501.001.501.001.501.001.501.001.502.001.001.502.001.001.50
ThreadLength
20202024292225302230223222322229372729372933
OverallLength
8080808489879095879592
10292
10297
104112102104112109113
ShankDia
8.08.09.09.09.0
11.211.211.211.211.212.512.512.512.514.014.014.014.014.014.016.016.0
SquareSize
6.36.37.17.17.19.09.09.09.09.0
10.010.010.010.011.211.211.211.211.211.212.512.5
NominalDiameter
22242424252525262727272828283030303032323333
Pitch
2.001.001.502.001.001,502.001.501.001.502.001.001.502.001.001,502.003.001.502.001.502.00
ThreadLength
38293535293535353037373037373037374837373737
OverallLength
118114120120114120120120120127127120127127120127127138137137137137
ShankDia
16.018.018.018.018.018.018.018.020.020.020.020.020.020.020.020.020.020.022.422.422.422.4
SquareSize
12.514.014.014,014.014.014.014.016.016.016.016.016.016.016.016.016.016.018.018.018.018.0
High Speed SteelGROUND THREAD HAND AND SHORT
MACHINE SCREWING TAPSFor ISO Metric Fine Pitch Threads
Specifications conform toIS 6175 : Part 3 : 1992
Dimensions in mm
NominalDiameter
3335363636383939394040404242424245454545484848485050505252525255
Pitch
3.01.51.52.03.01.51.52.03.01.52.03.01.52.03.04.01.52.03.04.01.52.03.04,01.52.03.01.52.03.04.01.5
ThreadLength
5139393957393939603939603939606045456767454567674545674545707045
Overal lLength
151144144144162149149149170149149170149149170170165165187187165165187187165165187175175200200175
ShankDia
22.425.025.025.025.028.028.028.028.028.028.028.028.028.028.028.031.531.531.531.531.531.531.531.531.531.531.535.535.535.535.535.5
SquareSize
18.020.020.020.020.022.422.422.422,422.422.422.422.422.422.422.425.025.025.025.025.025.025.025.025.025.025.028.028.028.028.028.0
NominalDiameter
5555555656565658585858606060606262626264646464656565656868686870
Pitch
2.03.04.01.52.03.04.01,52.03.04.01.52.03.04.01.52.03.04.01.52.03.04.01.52.03.04.01.52.03,04,01,5
ThreadLength
4570704545707048486464484864644848646448486464484864644848646448
OverallLength
175200200175175200200193193209209193193209209193193209209193193209209193193209209203203219219203
ShankDia
35.535.535.535.535.535.535.540.040,040.040,040.040.040.040.040.040.040.040.040.040.040.040,040.040.040.040.045.045.045.045,045. 0
SquareSize
28. 0
28. 0
28.0
28.0
28. 0
28.0
28.0
31.5
31.5
31.5
31.5
31.5
31. 5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31. 5
35. 5
35. 5
35.5
35.5
35.5
Back 194
High Speed SteelGROUND THREAD HAND AND SHORT
MACHINE SCREWING TAPSFor ISO Metric Fine Pitch Threads
Specifications conform toIS 6175 : Part 3 : 1992
Dimensions in mm
Back
1) Unless otherwise specified, the Screwing taps shall be supplied withtolerance class '6H', Non-Serial and with Straight flutes.
2) Usually supplied in sets consisting of two taps viz. Taper andBottoming.
195
NominalDiameter
707070707272727272757575757676767676788080
Pitch
2.03.04.06.01.52.03.04.06.01.52.03.04.01.52.03.04 06.02.01.52.0
ThreadLength
486464794848646479484864645151676783515151
Overal lLength
203219219234203203219219234203203219219226226242242258226226226
ShankDia
454545454545454545454545455050505050505050
SquareSize
35.535.535.535.535.535.535.535.535.535.535.535.535.540.040.040.040.040.040.040.040.0
NominalDiameter
80808082858585859090909095959595
100100100100
Pitch
3.04.06.02.02.03.04.06.02.03.04.06.02.03.04.06.02.03.04.06.0
ThreadLength
6767835151676786516767865470708954707089
OverallLength
242242258226226242242261226242242261244260260279244260260279
ShankDia
5050505050505050505050505656565656565656
SquareSize
40.040.040.040.040.040.040.040.040.040.040.040.045.045.045.045.045.045.045.045.0
High Speed SteelGROUND THREAD HAND AND SHORT
MACHINE SCREWING TAPSFor ISO Metric Fine Pitch Threads
Specifications conform toIS 6175 : Part 3 : 1992
Dimensions in mm
NominalDiameter
Inch
3/161/45/163/87/161/29/165/811/163/47/8
ThreadperInch
242018161412121111109
ThreadLength
mm
1619222425293032373738
OverallLength
mm
58667280858995
102112112118
ShankDiamm
5.006.308.00
10.008.009.00
11.2012.5014.0014.0016.00
SquareSizemm
4.005.006.308.006.307.109.00
10.0011.2011.2012.50
NominalDiameter
Inch
11.1/81.1/41.3/81.1/21.3/422.1/42.1/22.3/43
ThreadperInch
8776654.1/2443.1/23.1/2
ThreadLength
mm
4548515760677076797983
OverallLength
mm
130138151162170187200221224234258
ShankDiamm
18.020.022.425.028.031.535.540.040.045.050.0
SquareSizemm
14.016.018.020.022.425.028.031.531.535.540.0
Taps upto and including 3/8" dia. are supplied with full diameter shank and a neck between threadedportion and shank
Manufactured with straight flutes and a shank with square for driving.
Usually supplied in sets consisting of three taps, viz. Taper, Second and Bottoming.
Back 196
High Speed SteelGROUND THREAD HAND TAPS
BSW Form
Specifications conform toBS 949 : Part 2 : 1979(Class 2, Corresponds to Zone 3)
Dimensions in inch / mm
Taps upto and including 3/8" dia. are supplied with full diameter shank and a neck between threadedportion and shank
Manufactured with straight flutes and a shank with square for driving
Usually supplied in sets consisting of three taps viz., Taper, Second and Bottoming.
Back 197
NominalDiameter
Inch
3/161/45/163/87/161/29/165/811/163/47/81
ThreadperInch
322622201816161414121110
ThreadLength
mm
161922242529303237373845
OverallLength
mm
58667280858995102112112118130
ShankDiamm
5.006.308.00
10.008.009.00
11.2012.5014.0014.0016.0018.00
SquareSizemm
4.005.006.308.006.307.109.00
10.0011.2011.2012.5014.00
NominalDiameter
Inch
1.1/81.1/41.3/81.1/21.5/81.3/422.1/42.1/22.3/43
ThreadperInch
99888776665
ThreadLength
mm
4851576060677076797983
OverallLength
mm
138151162170170187200221224234258
ShankDiamm
20.022.425.028.028.031.535.540.040.045.050.0
SquareSizemm
16.018.020.022.422.425.028.031.531.535.540.0
High Speed SteelGROUND THREAD HAND TAPS
BSF Form
Specifications conform toBS 949 : Part 2 : 1979(Class 2, Corresponds to Zone 3)
Dimensions in inch / mm
NominalDiameter
Inch
1/45/163/87/161/29/165/83/47/81
ThreadperInch
201816141312111098
ThreadLength
mm
19222425293032373845
OverallLength
mm
667280858995
102112118130
ShankDiamm
6,38.0
10.08.09.0
11.212.514.016.018.0
SquareSizemm
5.06.38.06.37.19.0
10.011.212.514.0
NominalDiameter
Inch
1.1/81.1/41.3/81.1/21.3/422.1/42.1/22.3/43
ThreadperInch
77665
4.1/24.1/2
444
ThreadLength
mm
48515760677076797983
OverallLength
mm
138151162170187200221224234258
ShankDiamm
20.022.425.028.031.535.540.040.045.050.0
SquareSizemm
16.018.020.022.425.028.031.531.535.540.0
Taps upto and including 3/8" dia. are supplied with full diameter shank and a neck between threadedportion and shank
Manufactured with straight flutes and a shank with square for driving
Usually supplied in sets consisting of three taps viz., Taper, Second and Bottoming.
Back 198
High Speed SteelGROUND THREAD HAND TAPS
UNC Form
Specifications conform toBS 949 : Part 2 : 1979(Class 2, Corresponds to Zone 3)
Dimensions in inch / mm
NominalDiameter
Inch
1/45/163/87/161/29/165/8
ThreadperInch
28242420201818
ThreadLength
mm
19192022242525
OverallLength
mm
66697682849095
ShankDiamm
6.38.0
10.08.09.0
11.212.5
SquareSizemm
5.06.38.06.37.19.010.0
NominalDiameter
Inch
3/47/811.1/81.1/41.3/81.1/2
ThreadperInch
16141212121212
ThreadLength
mm
29333537373939
OverallLength
mm
104113120127137144149
ShankDiamm
14.016.018.020.022.425.028.0
SquareSizemm
11.212.514.016.018.020.022.4
Taps upto and including 3/8" dia. are supplied with full diameter shank and a neck between threadedportion and shank
Manufactured with straight flutes and a shank with square for driving
Usually supplied in sets consisting of three taps viz., Taper, Second and Bottoming.
Back 199
High Speed SteelGROUND THREAD HAND TAPS
UNF Form
Specifications conform toBS 949 : Part 2 : 1979(Class 2, Corresponds to Zone 3)
Dimensions in inch / mm
NominalDiameter
1/45/163/87/161/29/165/811/163/4
ThreadsperInch
262626262626262626
ThreadLength
11.1/81.1/41.1/41.1/41.1/41.1/41.1/41.1/2
OverallLength
2.1/22.3/42.15/16333333.1/4
ShankDia
0.2530.3150.3770.3230.3670.4290.4800.5420.590
SquareSize
0.1970.2420.2940.2420.2750.3220.3600.4060.442
Nominal Thread Overall Shank SquareLength LengthDiameter
7/811.1/81.2901.3701.4501.9/161.5/8
Dia
2424262424262424
1.1/21.1/21.1/21.1/21.1/21.1/222
3.1/43.1/4444455
0.6970.8000.8961.0211.1081.2331.3051.305
Size
0.5230.6000.6720.7660.8310.9250.9790.979
Manufactured with straight flutes and a shank with square for driving
Usually supplied in sets consisting of three taps viz., Taper, Second and Bottoming.
Back 200
ThreadsperInch
High Speed SteelGROUND THREAD HAND TAPS
BSCY Form
Specifications conform toBS 949 : 1951( Zone 3)
Dimensions in Inches
NominalDiameter
1/25/83/41
ThreadsperInch
18181616
ThreadLength
1.1/41.1/41.1/21,1/2
OverallLength
333.1/43,1/4
ShankDia
0.3670.4800.5900.800
SquareSize
0.2750.3600.4420.600
NominalDiameter
1.1/41.1/222.1/2
ThreadsperInch
16141414
ThreadLength
1.1/21.1/222
OverallLength
4455.1/4
ShankDia
1.0211.2331.6442.100
SquareSize
0.7660.9251.2331.575
Manufactured with whit worth thread form with straight flutes and a shank with square for driving
Usually supplied in sets consisting of three taps viz., Taper, Second and Bottoming.
Back 201
High Speed SteelGROUND THREAD HAND TAPS
BS Conduit Form
Specifications conform toBS 949 :1951(Zone 3)
Dimensions in Inches
NominalSiz e
1/81/43/81/25/83/47/811.1/4
ThreadsperInch
281919141414141111
ThreadLength
3/41.1/161.1/161.3/81.3/81.3/81.9/161.3/41.3/4
OverallLength
2.1/82.7/162.9/163.1/83.3/163.1/43.1/23.3/44
ShankDia
0.3180.4290.5420.6870.8000.9061.0931.1251.312
SquareSiz e
0.2380.3220.4060.5150.6000.6790.8120.8430.984
NominalSiz e
1.1/21.3/422.1/42.1/22.3/433.1/24
ThreadsperInch
111111111111111111
ThreadLength
1.3/41.3/41.3/42.1/8
2.9/162.9/162.5/8
2.11/162.3/4
OverallLength
4.1/44.3/84.1/255.1/25.3/466.1/26.3/4
ShankDia
1.5001.6251.8752.0002.2502.3752.6252.8123.000
SquareSize
1.1251.2181.4061.500
1.687
1.781
1.968
2.10 8
2.250
Manufactured with whit worth thread form with straight flutes and a shank with square for driving
Usually supplied in sets consisting of two taps viz., Taper and Bottoming.
Back 202
High Speed SteelGROUND THREAD HAND TAPS
BS (Parallel)
Specifications conform toBS 949 :1951(Zone 3)
Dimensions in Inches
NominalDiameter
inch
1/81/43/81/25/83/47/811.1/81.1/4
Threadsperinch
28191914141414111111
ThreadLength
mm
15192126262829333436
OverallLength
mm
596775879196
102109115119
ShankDiamm
8.010.012.516.018.020.022.425.028.031.5
SquareSizemm
6.38.0
10.012.5
14.016.018.020.022.425.0
NominalDiameter
inch
1.1/21.3/422.1/42.1/22.3/433.1/24
ThreadsperInch
111111111111111111
ThreadLength
mm
373941424546485053
OverallLength
mm
125132140142153160164173185
ShankDiamm
35.535.540.040.045.050.050.063.071.0
SquareSizemm
28.028.031.531.535.540.040.050.056.0
Manufactured with whit worth thread form with straight flutes and a shank with square for driving
Usually supplied in sets consisting of two taps viz., Taper and Bottoming.
Back 203
High Speed SteelGROUND THREAD HAND TAPS
BSP (Parallel) 'G' Series
Specifications conform toBS 949 :Part3 : 1982
Dimensions in inch / mm
NominalDiameter
Inch
1/81/43/81/23/41
ThreadsperInch
281919141411
ThreadLength
mm
151921262833
OverallLength
mm
5967758796
109
ShankDiamm
8.010.012.516.020.025.0
SquareSizemm
6.38.0
10.012.516.020.0
Nomina lDiameter
Inch
1.1/41.1/22
2.1/234
ThreadsperInch
111111111111
ThreadLength
mm
363741454853
Overal lLength
mm
119125140153164185
ShankDiamm
31.535.540.045.050.071.0
SquareSizemm
25.028.031.535.540.056.0
Manufactured with straight flutes and a shank with square for driving
Usually supplied in sets consisting of two taps viz., Taper and Bottoming,
Back 204
High Speed SteelGROUND THREAD HAND TAPS
BSP (Taper) Rc Series
Specifications conform toBS 949 : Part 3 : 1982
Dimensions in inch / mm
NominalSize
1/81/43/81/23/411.1/4
ThreadsperInch
271818141411.1/211.1/ 2
ThreadLength
3/41.1/161.1/161.3/81.3/81.3/41.3/4
OverallLength
2.1/82.7/162.9/163.1/83.1/43.3/44
ShankDia
0.3180.4290.5420.6870.9061.1251.312
SquareSize
0.2380.3220.4060.5150.6790.8430.984
NominalSize
1.1/222.1/233.1/24
ThreadsperInch
11.1/211.1/28888
ThreadLength
1.3/41.3/42.9/162.5/82.11/162.3/4
OverallLength
4.1/44.1/25.1/266.1/26.3/4
ShankDia
1.5001.8752.2502.6252.8123.000
SquareSize
1.1251.4061.6871.9682.1082.250
Manufactured with straight flutes and shank with square for driving
Usually supplied in sets consisting of two taps viz., Taper and Bottoming.
Back
205
High Speed SteelGROUND THREAD HAND TAPS
American National Taper Pipe Taps (NPT)
Specifications conform toBS 949 : 1969
Dimensions in inches
Manufactured with straight flutes and a long shank with a driving square for machine tapping.
Type 'A' - 5 Deg. Taper Angle with Long Taper LeadType 'B' -10 Deg, Taper Angle with Spiral pointType 'C - 20 Deg. Taper Angle with Shorter Taper LeadType 'D' -10 Deg, Taper Angle without Spiral point
Unless otherwise specified the Screwing Taps shall be supplied withtolerance class 6H.
Back 206
NominalDiameter
6789
101112141618
2224
20
Pitch
1.001.001.251.251.501.501.752.002.00
3.00
2.502.502.50
ThreadLength
19192222242529303237373845
OverallLength
89.089.097.097.0
108.0115.0119.0127.0137.0149.0149.0158.0172.0
ShankDia
4.55.66.37.18.08.09.0
11.212.514.014.016.018.0
SquareSize
3.554.505.005.606.306.307.10
9.0010.0011.2011.2012.5014.00
NominalDiameter
27303336394245485256606468
Pitch
3.003.503.504.004.004.504.505.005.005.505.506.006.00
ThreadLength
45485157606067677070767979
OverallLength
180.0183.201.0
0
214.5225.0225.0247.0247.0265.0265.0293.5296.5311.5
ShankDia
20.020.022.425.028.028.031.531.535.535.540.040.045.0
SquareSize
16.016.018.020.022.422.425.025.028.028.031.531.535.5
High Speed SteelGROUND THREAD LONG SHANK
MACHINE SCREWING TAPSFor ISO Metric Coarse Pitch Threads
Specifications conform toIS 6175 : Part 4 : 1991
Dimensions in mm
Back 207
NominalDiameter
678899
10101011111212121414141515161617
Pitch
0.750.750.751.000.751.000.751.001.250.751.001.001.251.501.001.251.501.001.501.001.501.00
ThreadLength
19191619161917202020202024292225302230223222
OverallLength
898991979497
104108108110110110119119124127127124127127137127
ShankDia
4.55.66.36.37.17.18.08.08.08.08.09.09.09.0
11.211.211.211.211.212.512.512.5
SquareSize
3.554.505.005.005.605.606.306.306.306.306.307.107.107.109.009.009.009.009.00
10.0010.0010.00
NominalDiameter
17181818202020222222242424252525
Pitch
1.501.001.502.001.001.502.001.001.502.001.001.502.001.001.502.00
26 1.502627272728
2.001.001.502.001.00
ThreadLength
32222937272937293338293535293535353530373730
OverallLength
137135142149140142149149153158157172172157163163163163165172172165
ShankDia
12.514.014.014.014.014.014.016.016.016.018.018.018.018.018.018.018.018.020.020.020.020.0
SquareSize
10.011.211.211.211.211.211.212.512.512.514.014.014.014.014.014.014.014.016.016.016.016.0
High Speed SteelGROUND THREAD LONG SHANK
MACHINE SCREWING TAPSFor ISO Metric Fine Pitch Threads
Specifications conform toIS 6175 : Part 4 : 1991
Dimensions in mm
NominalDiameter
282830303030323233333335363636383939394040
Pitch
1.52.01.01.52.03.01.52.01.52.03.01.51.52.03.01.51.52.03.01.52.0
ThreadLength
373730373748373737375139393957393939603939
OverallLength
172.0172.0165.0172.0172.0183.0187.0187.0187.0187.0201.0196.5196.5196.5214.5204.0204.0204.0225.0204.0204.0
ShankDia
20.020.020.020.020.020.022.422.422.422.422.425.025.025.025.028.028.028.028.028.028.0
SquareSize
16.016.016.016.016.016.018.018.018.018.018.020.020.020.020.022.422.422.422.422.422.4
NominalDiameter
4042424242454545454848484850505052525252
Pitch
3.01.52.03.04.01.52.03.04.01.52.03.04.01.52.03.01.52.03.04.0
ThreadLength
6039396060454567674545676745456745457070
OverallLength
225.0204.0204.0225.0225.0225.0225.0247.0247.0225.0225.0247.0247.0225.0225.0247.0240.0240.0265.0265.0
ShankDia
28.028.028.028.028.031.531.531.531.531.531.531.531.531.531.531.535.535.535.535.5
SquareSize
22.422.422.422.422.425.025.025.025.025.025.025.025.025.025.025.028.028.028.028.0
Type 'A' - 5 Deg. Taper Angle with Long Taper LeadType 'B' -10 Deg. Taper Angle with Spiral pointType 'C'- 20 Deg. Taper Angle with Shorter Taper LeadType 'D' - 10 Deg. Taper Angle without Spiral point.
Unless otherwise specified the Screwing Taps shall be supplied withtolerance class 6H.
Back 208
High Speed SteelGROUND THREAD LONG SHANK
MACHINE SCREWING TAPSFor ISO Metric Fine Pitch Threads
Specifications conform toIS 6175 : Part 4 : 1991
Dimensions in mm
Manufactured with straight flutes and a long shank with a square for machine tapping of nuts.
Unless otherwise specified the screwing taps shall be supplied with Tolerance class 6H
Back 209
NominalDiameter
6789
10111214161820
Pitch
1 001.001.251.251.501.501.752.002.002.502.50
ThreadLength
3236404045455056636370
OverallLength
110110125140140160180200200220250
ShankDia
4.55.66.37.18.08.09.0
11.212.514.014.0
SquareSize
3.554.505.005.606.306.307.109.00
10.0011.2011.20
NominalDiameter
22242730333639424548
Pitch
2.503.003.003.503.504.004.004.504.505.00
ThreadLength
808090
100110110125125140140
OverallLength
280280315315355400400450500500
ShankDia
16.018.020.020.022.425.028.028.031.531.5
SquareSize
12.514.016.016.018.020.022.422.425.025.0
High Speed SteelGROUND THREAD NUT SCREWING TAPS
For ISO Metric Coarse Pitch Threads
Specifications conform toIS 6175 : Part 5 : 1991
Dimensions in mm
Manufactured with straight flutes and a long shank with a square for machine tapping of nuts.
Back 210
NominalDiameter
Inch
1/45/1 6
3/87/1 6
1/29/1 6
5/83/4
ThreadsperInch
2018161412121110
ThreadLength
mm
3842485564647076
OverallLength
mm
110120140160180200200250
ShankDiamm
4.506.007.008.009.50
11.2012.5014.00
SquareSizemm
3.554.505.606.307.509.00
10.0011.20
NominalDiameter
Inch
7/811.1/81.1/41.1/ 21.3/42
ThreadsperInch
987765
4.1/2
ThreadLength
mm
8595
109109127153170
OverallLength
mm
280280315355400500560
ShankDiamm
16.018.020.022.428.031.5
35.5
SquareSizemm
12.5
14.0
16.018.0
22.425.028.0
High Speed SteelGROUND THREAD NUT TAPS
BSW Form
Specifications conform toBS 949-1969(Zone 3)
Dimensions in inch / mm
Manufactured with straight flutes and a long shank with a square for machine tapping of nuts.
Back 211
NominalDiameter
Inch
1/45/163/87/161/29/165/83/47/8
ThreadsperInch
262220181616141211
ThreadLength
mm
303538434848556470
OverallLength
mm
110120140160180200200250280
ShankDiamm
4.506.007.008.009.50
11.2012.5014.0016.00
SquareSizemm
3.554.505.606.307.509.00
10.0011.2012.50
NominalDiameter
Inch
11.1/81.1/41.3/81.1/21.5/81.3/42
ThreadsperInch
109988877
ThreadLength
mm
768585959595
109109
OverallLength
mm
280315355400400450500560
ShankDiamm
18.020.022.425.028.028.031.535.5
SquareSizemm
14.016.018.020.022.422.425.028.0
High Speed SteelGROUND THREAD NUT TAPS
BSF Form
Specifications conform toBS 949-1969(Zone 3)
Dimensions in inch / mm
Manufactured with straight flutes and a long shank with a square for machine tapping of nuts.
Back 212
NominalDiameter
Inch
1/45/163/87/161/29/165/83/4
ThreadsperInch
ThreadLength
mm
OverallLength
mm
110125140160180200200250
ShankDiamm
4.56.07.08.09.5
11.212.514.0
SquareSizemm
3.554.505.606.307.509.00
10.0011.20
NominalDiameter
Inch
1.1/81.1/41.3/81.1/21.3/42
ThreadsperInch
89
776654.1/2
ThreadLength
mm
9585
109109127127153170
OverallLength
mm
280280315355400400500560
ShankDiamm
16.018.020.022.425.028.031.535.5
SquareSizemm
12.514.016.018.020.022.425.028.0
High Speed SteelGROUND THREAD NUT TAPS
UNC Form
Specifications conform toBS 949-1969(Zone 3)
Dimensions in inch / mm
20 384348555964
7076
18
161413121110
7/81
Manufactured with straight flutes an d a long shank with a square for machine tapping of nuts.
Back 213
NominalDiameter
Inch
1/45/163/87/161/29/165/8
ThreadsperInch
28242420201818
ThreadLength
mm
28323238384343
OverallLength
mm
110125140160180200200
ShankDiamm
4.56.07.08.09.5
11.212.5
SquareSizemm
3.554.505.606.307.509.00
10.00
NominalDiameter
Inch
3/47/811.1/81.1/41.3/81.1/2
ThreadsperInch
16141212121212
ThreadLength
mm
48556464646464
OverallLength
mm
250280280315355400400
ShankDiamm
14.016.018.020.022.425.028.0
SquareSizemm
11.212.514.016.018.020.022.4
High Speed SteelGROUND THREAD NUT TAPS
UNF Form
Specifications conform toBS 949-1969(Zone 3)
Dimensions in inch / mm
Manufactured with straight flutes and a shank with square for driving.
Usually supplied in sets consisting of Three serial Hand taps viz., Rougher, Intermediate and Finisher tapUnless otherwise Specified , the screwing taps shall be supplied with tolerance class '6H'
Back 214
NominalDiameter
3.03.54.04.55.06.07.08.09.0
10.011.012.014.016.018.020,0
Pitch
0.50.60.70.750.81.01.01.251.251.51.51.752.02.02.52.5
ThreadLength
11131316161919222224242930324040
OverallLength
40454550505050566370707580809595
ShankDia
3.54.04.56.06.06.06.06,07.07.08.09.0
11.012.014.016.0
SquareSize
2.73.03.44.94.94.94.94.95.55.56.27.09.09.0
11.012.0
NominalDiameter
222427303336394245485256606468
Pitch
2.53.03.03.53.54.04.04.54.55.05.05.55.56.06.0
ThreadLength
405050565663636370757585859090
OverallLength
100110110125125150150150160180180200200220220
ShankDia
18.018.020.022.025.028.032.032.036.036.040.045.045.050.050.0
SquareSize
14.514.516.018.020.022.024.024.029.029.032.035.035.039.039.0
High Speed SteelGROUND THREAD HAND TAPS
For ISO Metric Coarse Pitch Threads
Specifications conform toDIN 352 - 1981
Dimensions in mm
Manufactured with straight flutes and a shank with square for driving.
Usually supplied in sets consisting of Two serial Hand taps viz., Rougher and Finisher tapUnless otherwise Specified, the screwing taps shall be supplied with tolerance class '6H'
Back 215
NominalDiameter
4.05.05.56.07.08.08.09.09.0
10.010.010.011.011.012.012.0
Pitch
0.50.50.50.750.750.751.00.751.00.751.01.250.751.01.01.25
ThreadLength
10121214141922192220202420202222
OverallLength
45505050505056566363637063637070
ShankDia
4.56.06.06.06.06.06.07.07.07.07.07.08.08.09.09.0
SquareSize
3.44.94.94.94.94.94.95.55.55.55.55.56.26.27.07.0
NominalDiameter
12
141414151516161818202022222424
Pitch
1.5
1.01.251.51.01.51.01.51.01.51.01.51.01.51.01.5
ThreadLength
22
222222222222222222222222222222
OverallLength
70
707070707070708080808080809090
ShankDia
9.0
11.011.011.012.012.012.012.014.014.016.016.018.018.018.018.0
SquareSize
7.0
9.09.09.09.09.09.09.0
11.011.012.012.014.514.514.514.5
High Speed SteelGROUND THREAD HAND TAPSFor ISO Metric Fine Pitch Threads
Specifications conform toDIN 2181 - 1981
Dimensions in mm
Back 216
NominalDiameter
24252527272828303032323333363636393939
Pitch
2.01.52.01.52.01.52.01.52.01.52.01.52.01.52.03.01.52.03.0
ThreadLength
22222222222222222222222525254040254040
Overal lLength
9090909090909090909090
100100100125125110125125
ShankDia
18181820202020222222222525282828323232
SquareSize
14.514.514.516.016.016.016.018.018.018.018.020.020.022.022.022.024.024.024.0
Nomina lDiamete r
404040424242454545484848505050525252
Pitch
1.52.03.01.52.03.01.52.03.01.52.03.01.52.03.01.52.03.0
ThreadLength
254040254040254040404040404040404040
Overal lLength
110125125110125125110125125140140140140140140140140140
ShankDia
323232323232363636363636363636404040
SquareSize
24.024.024.024.024.024.029.029.029.029.029.029.029.029.029.032.032.032.0
High Speed SteelGROUND THREAD HAND TAPSFor ISO Metric Fine Pitch Threads
Specifications conform toDIN 2181 - 1981
Dimensions in mm