SuperServer 5018R-M/MR Quick Reference Guide · 4GB 4GB 8GB 4GB 4GB 4GB 4GB 16GB 4GB 4GB 4GB 4GB...

1
http://www.supermicro.com MNL-1605-QRG Board Layout SuperServer 5018R-M/MR Quick Reference Guide Rear View Power Button Reset Button Power LED Device Activity LED LAN1 LED & LAN2 LED Overheat & Fan Fail LED Hard Drive Signal Hard Drive Fail Description No. CPU Installation Beep Codes Front view & Interface Heatsink Installation 1. Place heatsink on top of installed CPU 2. Line up the four screws to socket 3. Push down heatsink and screw down as shown (cross pattern, in order: A, C, B, D) 4. NOTE: Only use 6-8 lb/f of torque; otherwise, hand-tighten each screw, to avoid damaging the system MEMORY Caution Top View of DDR4 Slot Release Tab Release Tab Note: Notch should align with the receptive key point on the slot. Notch Notch Front View Screw #B Screw #D Screw #C Screw #A HDD 0 HDD 1 HDD 2 HDD 3 7 8 1 2 3 4 5 6 7 8 SAFETY INFORMATION IMPORTANT: See installation instructions and safety warning before connecting system to power supply. http://www.supermicro.com/about/policies/safety_information.cfm WARNING: To reduce risk of electric shock/damage to equipment, disconnect power from server by disconnecting all power cords from electrical outlets. If any CPU socket empty, install protective plastic CPU cap CAUTION: Always be sure all power supplies for this system have the same power output. If mixed power supplies are installed, the system will not operate. For more information go to : http://www.supermicro.com/support ! ! ! BIOS Beep Codes Beep Code/LED Message Description 5 short beeps + 1 long beep Memory 8 long beeps Display memory read/ write status Video adapter missing or with faulty memory No memory detected 1 beep Refresh Circuits have been reset. (Ready to power up) OH LED On System overheat System Slot B2 (Blue Slot) Slot B1 Slot A1 Slot A2 (Blue Slot) Towards the edge of the motherboard Towards the CPU X10SRi-F JP3 JTPM1 JF1 JD1 J23 T-SGPIO1 T-SGPIO2 T-SGPIO3 JOH1 JL1 JPME2 JWD1 JPG1 JPF2 JPF1 JPB1 JI2C2 JI2C1 JBR1 JVRM2 JVRM1 JPL1 JSD1 JSD2 JIPMB1 JPWR1 JUIDB1 LE1 LE2 LEDM1 JBT1 BT1 FAN4 FAN1 FAN2 FAN3 FANA FAN5 J24 JPI2C1 JSTBY1 S-SATA9 I-SATA4 I-SATA0 I-SATA1 I-SATA2 I-SATA3 S-SATA8 I-SATA5 SP1 CPU CPU SLOT5 PCI-E 3.0 X4(IN X8) CPU SLOT4 PCI-E 3.0 X8 CPU SLOT3 PCI-E 3.0 X8 USB0/1 DIMMC2 :TPM/PRO80 USB8/9 USB6/7 USB2/3 (3.0) LAN1 DIMMA2 DIMMA1 USB10(3.0) LAN2 USB4/5 PCH SLOT2 PCI-E 2.0 X4(IN X8) PCH SLOT1 PCI-E 2.0 X2(IN X8) COM2 COM1 DIMMB2 DIMMB1 PWR I2C DIMMD2 DIMMD1 DIMMC1 IPMI_LAN UID USB11(3.0) VGA CPU SLOT6 PCI-E 3.0 X16 BAR CODE IPMI CODE MAC CODE BIOS LICENSE BIOS Description No. PCH Slot1 PCI-E 2.0 x2 (in x8) PCH Slot2 PCI-E 2.0 x4 (in x8) CPU Slot3 PCI-E 3.0 x8 CPU Slot4 PCI-E 3.0 x8 CPU Slot5 PCI-E 3.0 x4 (in x8) CPU Slot6 PCI-E 3.0 x16 DIMMA2 (BLUE) slot DIMMA1 slot DIMMB2 (BLUE) slot DIMMB1 slot CPU DIMMD2 (BLUE) slot DIMMD1 slot DIMMC2 (BLUE) slot DIMMC1 slot JBT1 = CMOS Reset I-SATA 5: Intel PCH Serial ATA (SATA 3.0) Ports 0/1 (6Gb/s) JSD1 & JSD2 = Disk On Module (DOM) Power I-SATA 0~4: Intel PCH Serial ATA (SATA 3.0) Ports 0/1 (6Gb/s) S-SATA 6~9: Intel PCH Serial ATA (SATA 3.0) Ports 0/1(6Gb/s) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 19 18 1 2 3 4 5 11 12 13 14 15 6 7 8 9 10 S-SATA7 S-SATA6 20 17 16 Description No. 1 2 3 4 5 6 7 8 9 PCI-E Expansion Slot (w/riser card) UID VGA Port GbE LAN1/LAN2 Port USB Port 2/3 (3.0) USB Port 0/1 (2.0) COM1 Port Dedicated LAN for IPMI Single Power Supply Module 1 3 9 5 4 7 8 2 6 1 2 3 4 5 6 Socket Keys CPU Keys Populating RDIMM/LRDIMM DDR4 Memory Modules Type Ranks Per DIMM and Data Width DIMM Capacity (GB) Speed (MT/s); Voltage (V); Slots per Channel (SPC) and DIMMs per Channel (DPC) 2 Slots per Channel 1 DPC 2 DPC E5-2600 V3 E5-2600 V4 E5-2600 V3 E5-2600 V4 4 Gb 8 Gb 1.2 V 1.2 V 1.2 V 1.2 V RDIMM SRx4 8 GB 16 GB 2133 2400 1866 2133 RDIMM SRx8 4 GB 8 GB 2133 2400 1866 2133 RDIMM DRx8 8 GB 16 GB 2133 2400 1866 2133 RDIMM DRx4 16 GB 32 GB 2133 2400 1866 2133 LRDIMM QRx4 32 GB 64 GB 2133 2400 2133 2400 LRDIMM 3DS 8Rx4 64 GB 128 GB 2133 2400 2133 2400 Rev. 1.0a

Transcript of SuperServer 5018R-M/MR Quick Reference Guide · 4GB 4GB 8GB 4GB 4GB 4GB 4GB 16GB 4GB 4GB 4GB 4GB...

Page 1: SuperServer 5018R-M/MR Quick Reference Guide · 4GB 4GB 8GB 4GB 4GB 4GB 4GB 16GB 4GB 4GB 4GB 4GB 4GB 4GB 24GB 4GB 4GB 4GB 4GB 4GB 4GB 4GB 4GB 32GB ... BIOS Beep Codes Beep Code/LED

http://www.supermicro.com MNL-1605-QRG

Board Layout

SuperServer 5018R-M/MR Quick Reference Guide

Rear View

Power Button

Reset Button

Power LED

Device Activity LED

LAN1 LED & LAN2 LED

Overheat & Fan Fail LED

Hard Drive Signal

Hard Drive Fail

DescriptionNo.

CPU Installation

Beep Codes

Front view & Interface

Heatsink Installation

1. Place heatsink on top of installed CPU2. Line up the four screws to socket3. Push down heatsink and screw down as shown (cross pattern, in order: A, C, B, D)4. NOTE: Only use 6-8 lb/f of torque; otherwise, hand-tighten each screw, to avoid damaging the system

MEMORY

Caution

Top View of DDR4 Slot

Release Tab Release Tab

Note: Notch should align with the receptive key point on the slot.

Notch Notch

Front View

Screw #BScrew #D

Screw #CScrew #A

HDD 0 HDD 1 HDD 2 HDD 3

78

1

2

3

4

5

6

7

8

SAFETY INFORMATIONIMPORTANT: See installation instructions and safety warning before connecting system to power supply.http://www.supermicro.com/about/policies/safety_information.cfm

WARNING: To reduce risk of electric shock/damage to equipment, disconnect power from server by disconnecting all power cords from electrical outlets.If any CPU socket empty, install protective plastic CPU cap

CAUTION: Always be sure all power supplies for this system havethe same power output. If mixed power supplies are installed, the system will not operate.

For more information go to : http://www.supermicro.com/support

!

!

!

BIOS Beep CodesBeep Code/LED Message Description

5 short beeps + 1 long beep

Memory

8 long beeps Display memory read/write status

Video adapter missing or with faulty memory

No memory detected

1 beep Refresh Circuits have been reset. (Ready to power up)

OH LED On System overheatSystem

Slot B2 (Blue Slot)Slot B1

Slot A1Slot A2 (Blue Slot)

Towards the edge of the motherboard

Towards the CPU

X10SRi-F

JP3

JTPM1

JF1

JD1

J23

T-SGPIO1

T-SGPIO2T-SGPIO3 JOH1

JL1

JPME2

JWD

1

JPG1

JPF2

JPF1

JPB1

1

JI2C2

JI2C1

JBR1

JVRM2

JVRM1

JPL1

JSD1JSD2

JIPMB1

JPWR1

JUIDB1

LE1

LE2

LEDM1

JBT1

BT1

FAN

4

FAN

1

FAN

2

FAN

3

FANA

FAN5

J24

JPI2C1

JSTBY1

S-SATA9

I-SATA4

I-SATA0

I-SATA1

I-SATA2I-SATA3

S-SATA8

I-SATA5

SP1

1-2:ENABLE

2-3:DISABLE

JPB1:BMC

CPU

CPU SLO

T5 PCI-E 3.0 X4(IN X8)

CPU SLO

T4 PCI-E 3.0 X8

CPU SLO

T3 PCI-E 3.0 X8

JPME2

2-3:ME M

ANU

FACTURU

NG

MO

DE

1-2:Norm

al

USB0/1

DIM

MC2

PWR LED

1-3:JD

1:

SPEAKER4-7:

JBR11-2:N

orma l

2-3:BIOS recovery

:TPM/PRO

80

USB8/9

USB6/7

LED

NMI

PWR

X

USB2/3(3.0)

HDD

NIC1

JWD

1:Watch D

og1-2:RST2-3:N

MI

LAN1

DIM

MA

2D

IMM

A1

USB10(3.0)

FF

2NIC

OH

LAN2

RST

PWR

PWRFAIL

USB4/5

ON

1-2:ENABLE

2-3:DISABLE

JPG1:VG

A

JI2C1/JI2C2I2C bus for PCI-E slot

OFF: D

ISABLEO

N: EN

ABLE

PCH SLO

T2 PCI-E 2.0 X4(IN X8)

PCH SLO

T1 PCI-E 2.0 X2(IN X8)

COM2

COM1

DIM

MB2

DIM

MB1

PWR I2C

DIM

MD

2D

IMM

D1

DIM

MC1

IPMI_LAN

UID

USB11(3.0)

0N: PO

WER FO

RCE ON

JPL1:LAN1/21-2:ENABLE

VGA

2-3:DISABLE

CPU SL O

T6 PCI-E 3.0 X16

BAR CODE

IPMI CODE

MAC CODEBIOS LICENSE

BIOS

DescriptionNo.PCH Slot1 PCI-E 2.0 x2 (in x8)

PCH Slot2 PCI-E 2.0 x4 (in x8)

CPU Slot3 PCI-E 3.0 x8

CPU Slot4 PCI-E 3.0 x8

CPU Slot5 PCI-E 3.0 x4 (in x8)

CPU Slot6 PCI-E 3.0 x16

DIMMA2 (BLUE) slot

DIMMA1 slot

DIMMB2 (BLUE) slot

DIMMB1 slot

CPU

DIMMD2 (BLUE) slot

DIMMD1 slot

DIMMC2 (BLUE) slot

DIMMC1 slot

JBT1 = CMOS Reset

I-SATA 5: Intel PCH Serial ATA (SATA 3.0) Ports 0/1 (6Gb/s)

JSD1 & JSD2 = Disk On Module (DOM) Power

I-SATA 0~4: Intel PCH Serial ATA (SATA 3.0) Ports 0/1 (6Gb/s)

S-SATA 6~9: Intel PCH Serial ATA (SATA 3.0) Ports 0/1(6Gb/s)

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

19 18

1 2 3 4 5 11 12 13 14 156 7 8 9 10

S-SATA7

S-SATA6

20 17 16

DescriptionNo.1

2

3

4

5

6

7

8

9

PCI-E Expansion Slot (w/riser card)

UID

VGA Port

GbE LAN1/LAN2 Port

USB Port 2/3 (3.0)

USB Port 0/1 (2.0)

COM1 Port

Dedicated LAN for IPMI

Single Power Supply Module

139 5 478 26

123456

Socket Keys

CPU Keys

Populating RDIMM/LRDIMM DDR4 Memory Modules

Type

Ranks Per DIMM and Data

Width

DIMM Capacity (GB)

Speed (MT/s); Voltage (V); Slots per Channel (SPC) and DIMMs per Channel (DPC)

2 Slots per Channel

1 DPC 2 DPC

E5-2600 V3 E5-2600 V4 E5-2600 V3 E5-2600 V4

4 Gb 8 Gb 1.2 V 1.2 V 1.2 V 1.2 V

RDIMM SRx4 8 GB 16 GB 2133 2400 1866 2133

RDIMM SRx8 4 GB 8 GB 2133 2400 1866 2133

RDIMM DRx8 8 GB 16 GB 2133 2400 1866 2133

RDIMM DRx4 16 GB 32 GB 2133 2400 1866 2133

LRDIMM QRx4 32 GB 64 GB 2133 2400 2133 2400

LRDIMM 3DS 8Rx4 64 GB 128 GB 2133 2400 2133 2400

Rev. 1.0a