Submittal 09 29 00 SUPER C FLAME CURB® - Pharos … · Non-Combustible: ASTM E 136, R value: ......

Goo

d to

the

left

onl

ySU

PER

CSU

PER

C

SUPE

R C

SUPER C

SUPER C

SUPER CSUPER C

SUPER C

SUPER C SUPER C

SUPER CSUPER C

SUPER C

SUPER C SUPER C

SUPE

R C

SUPE

R C

SUPE

R C

SUPER C

SUPER C

11/2

11/2

TYPE

XXX

TYPE XXX

11/2

11/2TYPE XXX

"Quality to the Core" R

a division of PABCO® building products, LLC

Description: PABCO® FLAME CURB® gypsum wallboard is a family of gypsum panel products composed of a fire-resistant gypsum core, reinforced with glass fibers which provides increased strength and enhanced fire-resistant properties. The face paper is folded around the long edges to reinforce as well as to protect the core; the panel ends are cut square. The long panel edges are tapered, allowing a recessed joint area to be reinforced and concealed to create a monolithic wall or ceiling surface suitable for decoration. PABCO® 5/8" FLAME CURB® type X and 1/2" FLAME CURB® type XXX meet and/or exceed the requirements specified by ASTM under its wallboard standard ASTM C 1396 type-X. FLAME CURB® Super ‘C’, in thicknesses of 1/2" and 5/8", exceed all of these previously mentioned “classified” core formulations in fire-resistance performance. (Systems are specifically tested at approved laboratories (see listing under Application) using these various core formulas, and those systems which successfully pass the stringent fire tests are approved for construction and are listed in the fire testing lab directory or in the Gypsum Association Fire Resistance Design Manual GA-600).PABCO® FLAME CURB® is manufactured with 100% recycled paper on face and back sides, affording a surface designed to receive joint treatment, paint, wall covering, or textured coatings.

PABCO® Gypsum Specification PGS-002ASTM specification C 1396Available in MOLD CURB® Plus type X

PABCO® Gypsum endorses the Gypsum Association’s publication GA-216 and ASTM Standard Specification C 840 as its application documents, which provide detailed instructions on the standard application of wallboard panels and proper joint finishing procedures.PABCO® FLAME CURB® systems must be installed in strict compliance with the detailed fire test assembly description, including core types and other components such as studs, fastener spacing and fasteners required, and applied as tested. To qualify for listed sound ratings, special caulking, insulation, or clips are generally added to the systems as detailed in the test report.Those systems that have been fire and sound tested are listed in the following: • Gypsum Association “Fire Resistance Design Manual” (GA-600). • PABCO® Gypsum Quality to the Core® Brochure (see PABCO® Gypsum website).• ICC: ESR 1338.• UL “Fire Resistance Directory”.• ITS, NGTS, NRC, RAL, SWRi, UL, or WFCi Test Reports.

Finishing of joints, wall or ceiling surfaces, and covering fasteners, is addressed in GA-214, GA-216, and ASTM C 840.

Application:

PABCO® FLAME CURB® is a non-structural wall covering material intended for interior walls, ceilings, and partitions in residential and commercial applications which often require specific fire-resistant assemblies. Additional applications include use as a roof underlayment per GA-276. This product is designed for direct mechanical attachment to metal or wood framing members. With the wallboard joints properly treated per GA-216 and GA-214, PABCO® FLAME CURB® will resist the passage of smoke.

PABCO® FLAME CURB® is intended for interior applications, and shall not be used where there will be direct exposure to water or continuous high humidity before, during, and after construction. Avoid exposure to temperatures exceeding 125 oF (52 oC) for an extended period of time. PABCO® FLAME CURB® is a non-structural panel, not to be used as a structural fastener base or to support wall or ceiling mounted objects.All materials used in conjunction with the application of PABCO® FLAME CURB® type X, XXX, or Super ‘C’ gypsum panels in Fire or Sound Rated systems shall be as specified in the applicable specific test report.

FLAME CURB® Type X, Type XXX, Type C

Gypsum Wallboard

Submittal 09 29 00

tothe ®

PABCO® Gypsuma division of PABCO® building products, LLCPO Box 417094Rancho Cordova, CA 95741Technical Services: 866-282-9298www.pabcogypsum.com

Primary Uses:

Limitations:

SUPE

R C

SUPE

R C

SUPE

R C

SUPER C

SUPER C

SUPER CSUPER C

SUPER C

SUPER C SUPER C

SUPER CSUPER C

SUPER C

SUPER C SUPER C

SUPE

R C

SUPE

R C

SUPE

R C

SUPER C

SUPER C

11/2

11/2

TYPE

XXX

TYPE XXX

11/2

11/2TYPE XXX

Goo

d to

the

left

onl

y

Storage & Handling:

SJ/06-06-11/Flame Curb® PABCO® Gypsum

Store all PABCO® gypsum panels flat; do not store on edge as panels are heavy and may fall over causing injury or death. Store in an area that offers protection from adverse weather conditions, condensation, and other forms of moisture. Avoid job site conditions that expose gypsum board to water or moisture. Plastic shipping bags are temporary, intended for protection during transit only, and must be removed promptly upon arrival. Store gypsum board under protected cover, off the ground with sufficient support to prevent sagging. Exercise proper care to avoid impact, scuffing of the paper faces, undue flexing, and damage to board edges, corners, and ends.

Manufacturing: ASTM C 1396; www.astm.org Federal Specification SS-L-30D Type III, Grade X *Installation: Gypsum Association GA-216, GA-214; www.gypsum.org ASTM C 840, www.astm.orgFire-Resistant Assemblies: Gypsum Association GA-600, Fire Design Manual Underwriters Laboratories, UL Fire Resistance Directory Surface Burning ASTM E 84; UL: Fire Resistance DirectoryCharacteristics: Flame Spread 15, Smoke Developed 0Non-Combustible: ASTM E 136, www.astm.orgR value: 1/2" = 0.45; 5/8" = 0.48 Thermal ResistanceVOC/Asbestos content: Free of VOC (Volatile Organic Compound) & asbestosMaterial Safety Data Sheet: MSDS available at www.pabcogypsum.com, Technical DataPABCO Gypsum: “Construction Guide - Fire & Sound Rated Systems”Foil Application: Foil may be applied to the back of ASTM C 1396 gypsum wallboard for the purpose of complying with ASTM C 1396 paragraph 5.1.Recycled Content: Refer to PABCO® Sustainable Materials Data Sheet for plant specific details.Please check our website at www.pabcogypsum.com for the latest edition of this specification.

* The federal specification for gypsum board, SS-L-30d was withdrawn in 1984. It is provided here for informational purposes only.

Fire Resistance Rated assembly designs are promulgated from tests performed at IAS* certified independent testing laboratories, and these designs include specific materials assembled in a precise configuration. When choosing construction details to achieve specific fire resistance rated requirements, care must be taken to insure that each component of the specified assembly is the proper one specified in the test report, and assembled in accordance with the specific requirements of the assembly. *(The International Accreditation Service —IAS— is a non-profit, public benefit corporation and a leading accreditation body in the United States. Internationally recognized, accreditation by IAS makes it easier to market products and services both inside and outside the United States.)

Product UL Core Type Edge Type1 Thickness2 Width2 Length3 Weight4

Type XXX PG-3 TE 1/2" 48" 8', 12' 1.9 lbs/ft2

Super C PG-C TE 1/2" 48" 12' 2.0 lbs/ft2

Type X PG-11 TE & RE1 5/8" 48"&54" 8'-12' 2.2 lbs/ft2

Super C TYPE C TE 5/8" 48" 12' 2.4 lbs/ft2

Packaging: 2 pieces per bundle, face-to-face, and end labeled.1 Edge types: Tapered Edge (TE). Round Edge (RE) is available (only) on FLAME CURB® 5/8" x 48" widths.2 Units of measure: inches.3 Units of measure: feet. Other lengths may be available on a special order basis. Refer to PABCO’s “Products-

Packaging-Weights” page. Consult with your local PABCO® representative, or call PABCO® Technical Assistance.4 Represents approximate weight for design and shipping purposes. A more exact weight may be available for your

area; consult with your local PABCO® representative, or call PABCO® Technical Assistance.

1

Limited Warranty: PABCO® Building Products, LLC, warrants that on the date the gypsum board is shipped from its manufacturing plant the gypsum board is free from defects in materials and manufacture. NOTWITHSTANDING THE FOREGOING, IT IS THE RESPONSIBILITY OF THE GYPSUM BOARD APPLICATOR TO NOTIFY PABCO BUILDING PRODUCTS, LLC, IN WRITING WITHIN TWENTY FOUR (24) HOURS OF DISCOVERY OF ANY VISIBLY DEFECTIVE GYPSUM BOARD PRIOR TO SUCH VISIBLY DEFECTIVE GYPSUM BOARD BEING APPLIED; FAILURE TO DO SO MAY FURTHER LIMIT OR VOID THE RESPONSIBILITIES OF PABCO BUILDING PRODUCTS, LLC, UNDER THIS WARRANTY. This warranty will remain in place for one year from the date of shipment from the manufacturing plant. THIS EXPRESS WARRANTY IS THE EXCLUSIVE WARRANTY PROVIDED BY PABCO® BUILDING PRODUCTS, LLC, AND SUPERSEDES ANY PRIOR, CONTRARY OR ADDITIONAL REPRESENTATIONS, WHETHER ORAL OR WRITTEN. PABCO® BUILDING PRODUCTS, LLC, HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES – WHETHER EXPRESS, IMPLIED, OR STATUTORY – INCLUDING ANY WARRANTY OF MERCHANTABILITY, ANY WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY IMPLIED WARRANTIES OTHERWISE ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

If the gypsum board fails to conform to the foregoing warranty in Paragraph 1 and such nonconformity is not due to misuse or improper maintenance or storage, Buyer shall notify PABCO® Building Products, LLC, in writing, and within 60 days of discovery, PABCO® Building Products, LLC, shall provide, at its sole and absolute discretion, one of the following: (i) repair or replacement of any nonconforming or defective gypsum wallboard; or (ii) credit or full refund of the purchase price. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY OF BUYER FOR ANY BREACH OF WARRANTY.

IN NO EVENT SHALL PABCO® BUILDING PRODUCTS, LLC, BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, WHETHER RESULTING FROM NONDELIVERY OR FROM THE USE, MISUSE, OR INABILITY TO USE THE PRODUCT OR FROM DEFECTS IN THE PRODUCT OR FROM NEGLIGENCE OR OTHER TORT. This exclusion applies regardless of whether such damages are sought for breach of warranty, breach of contract, negligence, or strict liability in tort or under any other legal theory.

Trademarks: The following trademarks used herein are owned by Pacific Coast Building Products and licensed to PABCO® Gypsum: PABCO®, PABCORE®, FLAME CURB®, WATER CURB®, MOLD CURB®, Quality to the Core®, and ABUSE CURB™. Note: Products described herein may not be available in all geographic markets. Consult your PABCO® Gypsum sales representative for information.

Product Data:Sizes and Types

Applicable Standards & Reference Documents:

Fire Resistant Ratings:

Submittal Approvals: Job name:

Contractor: Date:

5/8”

x 1

2’

5/8” x12’

5/8”

x 1

2’

5/8” x 12’

5/8”

x 1

2’

5/8” x 12’

5/8”

x 1

2’

5/8” x 12’

SUPE

R C

PANE

L DE

YES

O F

ABRI

CADO

DE

ACUE

RDO

A L

A NO

RMA

ASTM

C 1

396

- PAN

EL D

E YE

SO P

ARA

SOFI

TO E

XTER

IOR

TIPO

C

PABC

O®

GYP

SUM

, UNA

DIV

ISIÓ

N DE

PAB

CO®

BUIL

DING

PRO

DUCT

S, L

LC N

EWAR

K, C

ALIF

ORN

IA, U

SA 9

4560

PABCO® G

YPSUM, UNA DIVISIÓ

N DE PABCO® BUILDING

PRODUCTS, LLC NEW

ARK, CALIFORNIA, USA 94560

PANEL DE YESO FABRICADO

DE ACUERDO A LA NO

RMA ASTM

C 1396 - PANEL DE YESO PARA SO

FITO EXTERIO

R TIPO C

GYPS

UM B

OARD

MAN

UFAC

TURE

D TO

MEE

T AS

TM C

139

6 - E

XTER

IOR

GYPS

UM S

OFFI

T BO

ARD

TYPE

C

PABC

O® GY

PSUM

, DIV

. OF

PABC

O® BU

ILDI

NG P

RODU

CTS,

LLC

, NEW

ARK,

CA,

945

60 U

SA

PABCO® GYPSUM

, DIV. OF PABCO® BUILDING PRODUCTS, LLC, NEW

ARK, CA, 94560 USA

GYPSUM BOARD M

ANUFACTURED TO MEET ASTM

C 1396 - EXTERIOR GYPSUM SOFFIT BOARD TYPE C

EXTE

RIO

RG

YP

SUM

SO

FFIT

BO

AR

DTY

PE

C

EXTER

IOR

GY

PSU

MS

OFFIT

BO

AR

DTY

PE C

PAN

EL D

E Y

ESO

PA

RA

SO

FITO

EXTE

RIO

RTI

PO

C

PAN

EL DE Y

ESOP

AR

AS

OFITO

EXTER

IOR

TIPO

C

1/2”

x 1

2’

1/2” x 12’1/2” x 12’

1/2”

x 1

2’1/

2” x

12’

1/2” x 12’1/2” x 12’

1/2”

x 1

2’

19673-00

19673-00

19673-00

EXTE

RIO

RG

YP

SUM

SO

FFIT

BO

AR

D

EXTER

IOR

GY

PSU

MS

OFFIT

BO

AR

D

PANE

L DE

YES

O F

ABRI

CADO

DE

ACUE

RDO

A L

A NO

RMA

ASTM

C 1

396

- PAN

EL D

E YE

SO P

ARA

SOFI

TO E

XTER

IOR

PABC

O®

GYP

SUM

, UNA

DIV

ISIÓ

N DE

PAB

CO®

BUIL

DING

PRO

DUCT

S, L

LC N

EWAR

K, C

ALIF

ORN

IA, U

SA 9

4560

PABCO® G

YPSUM, UNA DIVISIÓ


PRODUCTS, LLC NEW



DE ACUERDO A LA NO

RMA ASTM


FITO EXTERIO

R

GYPS

UM B

OARD

MAN

UFAC

TURE

D TO

MEE

T AS

TM C

139

6 - E

XTER

IOR

GYPS

UM S

OFFI

T BO

ARD

PABC

O® GY

PSUM

, DIV

. OF

PABC

O® BU

ILDI

NG P

RODU

CTS,

LLC

, NEW

ARK,

CA,

945

60 U

SA

PABCO® GYPSUM


ARK, CA, 94560 USA

GYPSUM BOARD M


C 1396 - EXTERIOR GYPSUM SOFFIT BOARD

PAN

EL D

E Y

ESO

PA

RA

SO

FITO

EXTE

RIO

R

PAN

EL DE Y

ESOP

AR

AS

OFITO

EXTER

IOR



Description & Primary Uses:

PABCO® Specification PGS-005ASTM specification C 1396Available in MOLD CURB® Plus

PABCO® Gypsum recommends that its Exterior Gypsum Soffit Board application conform to recommendations in GA-216 and ASTM C 840. Panels shall be applied perpendicular to ceiling joists, in a horizontal plane or inclined downward away from the structure in ceiling applications. Panels may be used as a covering on interior wall surfaces. All joints and fasteners not covered by exterior cladding or outer layers in a multi-layer system shall be finished with tape and joint compound.

Unless protected by metal or other water stops, all edges of the soffit board shall be spaced a minimum of 1/4"(inch) away from adjacent vertical surfaces. Suitable fascia and molding shall be provided around the perimeter of the soffit or ceiling to protect the gypsum panels from direct exposure to water.

All soffit board indirectly exposed shall be decorated with an approved exterior cladding or painting system. When PABCO® type X Exterior Gypsum Soffit Board is specified for use in fire rated systems, the UL core type specified and the application method must be as specified in the fire tested system selected.

• PABCO® Exterior Gypsum Soffit Board shall not be subjected to direct exposure to weather, and water.• 24" o.c. (on center) joist spacing is the maximum span for PABCO® type X Exterior Gypsum Soffit Board.• An approved exterior surface decoration (alkyd paint) must be applied to all exposed soffit board. (See TSR: 1338).• All materials and application of PABCO® type X Exterior Gypsum Soffit Board on fire rated assemblies shall be as indicated in the fire test report.• PABCO® Exterior Gypsum Soffit Board Shall not be exposed to sustained temperatures exceeding 125o F (52o C).

• PABCO® Exterior Gypsum Soffit Board is non-structural, and not to be used as a structural fastener base, or to support heavy wall or ceiling mounted objects.

PABCO® Exterior Gypsum Soffit Board is designed for exterior ceiling application on the underside of exterior soffits, open porches, walkways, carport ceilings and similar installations that are completely protected from contact with water. The core and paper has been formulated to enhance its ability to resist sagging when applied in the prescribed manner. PABCO® Exterior Soffit Board panels are manufactured in 1/2" Regular, 1/2" type XXX, 5/8"type X, and 5/8" type C cores. The face paper is cream or light-brown colored with the core type printed in the taper area along the long-edges. The long panel edges are tapered to receive joint treatment.


Submittal 09 29 00

EXTERIOR SOFFIT BOARD

Regular, Type X, Type C Sag Resistant

tothe ®

Application:

Limitations:

5/8”

x 1

2’

5/8” x12’

5/8”

x 1

2’

5/8” x 12’

5/8”

x 1

2’

5/8” x 12’

5/8”

x 1

2’

5/8” x 12’

SUPE

R C

PANE

L DE

YES

O F

ABRI

CADO

DE

ACUE

RDO

A L

A NO

RMA

ASTM

C 1

396

- PAN

EL D

E YE

SO P

ARA

SOFI

TO E

XTER

IOR

TIPO

C

PABC

O®

GYP

SUM

, UNA

DIV

ISIÓ

N DE

PAB

CO®

BUIL

DING

PRO

DUCT

S, L

LC N

EWAR

K, C

ALIF

ORN

IA, U

SA 9

4560

PABCO® G

YPSUM, UNA DIVISIÓ


PRODUCTS, LLC NEW



DE ACUERDO A LA NO

RMA ASTM


FITO EXTERIO

R TIPO C

GYPS

UM B

OARD

MAN

UFAC

TURE

D TO

MEE

T AS

TM C

139

6 - E

XTER

IOR

GYPS

UM S

OFFI

T BO

ARD

TYPE

C

PABC

O® GY

PSUM

, DIV

. OF

PABC

O® BU

ILDI

NG P

RODU

CTS,

LLC

, NEW

ARK,

CA,

945

60 U

SA

PABCO® GYPSUM


ARK, CA, 94560 USA

GYPSUM BOARD M


C 1396 - EXTERIOR GYPSUM SOFFIT BOARD TYPE C

EXTE

RIO

RG

YP

SUM

SO

FFIT

BO

AR

DTY

PE

C

EXTER

IOR

GY

PSU

MS

OFFIT

BO

AR

DTY

PE C

PAN

EL D

E Y

ESO

PA

RA

SO

FITO

EXTE

RIO

RTI

PO

C

PAN

EL DE Y

ESOP

AR

AS

OFITO

EXTER

IOR

TIPO

C

1/2”

x 1

2’

1/2” x 12’1/2” x 12’

1/2”

x 1

2’1/

2” x

12’

1/2” x 12’1/2” x 12’

1/2”

x 1

2’

19673-00

19673-00

19673-00

EXTE

RIO

RG

YP

SUM

SO

FFIT

BO

AR

D

EXTER

IOR

GY

PSU

MS

OFFIT

BO

AR

D

PANE

L DE

YES

O F

ABRI

CADO

DE

ACUE

RDO

A L

A NO

RMA

ASTM

C 1

396

- PAN

EL D

E YE

SO P

ARA

SOFI

TO E

XTER

IOR

PABC

O®

GYP

SUM

, UNA

DIV

ISIÓ

N DE

PAB

CO®

BUIL

DING

PRO

DUCT

S, L

LC N

EWAR

K, C

ALIF

ORN

IA, U

SA 9

4560

PABCO® G

YPSUM, UNA DIVISIÓ


PRODUCTS, LLC NEW



DE ACUERDO A LA NO

RMA ASTM


FITO EXTERIO

R

GYPS

UM B

OARD

MAN

UFAC

TURE

D TO

MEE

T AS

TM C

139

6 - E

XTER

IOR

GYPS

UM S

OFFI

T BO

ARD

PABC

O® GY

PSUM

, DIV

. OF

PABC

O® BU

ILDI

NG P

RODU

CTS,

LLC

, NEW

ARK,

CA,

945

60 U

SA

PABCO® GYPSUM


ARK, CA, 94560 USA

GYPSUM BOARD M


C 1396 - EXTERIOR GYPSUM SOFFIT BOARD

PAN

EL D

E Y

ESO

PA

RA

SO

FITO

EXTE

RIO

R

PAN

EL DE Y

ESOP

AR

AS

OFITO

EXTER

IOR

SJ 6-06-11/Soffit PABCO® Gypsum

Storage & Handling: Store all PABCO® gypsum panels flat; do not store on edge as panels are heavy and may fall over causing injury or death. Store in an area that offers protection from adverse weather conditions, condensation, and other forms of moisture. Avoid job site conditions that expose gypsum board to water or moisture. Plastic shipping bags are temporary, and intended for protection during transit only, and must be removed promptly upon arrival. Store gypsum board under protected cover, off the ground with sufficient support to prevent sagging. Exercise proper care to avoid impact, scuffing of the paper faces, undue flexing, and damage to board edges, corners, and ends.

Submittal Approvals: Job name:Contractor: Date:

Product UL Core Type Thickness Width Length2 Weight1

Exterior Regular - 1/2" 48" 12' 1.7 lbs/ft2

Exterior Soffit type X PG-3 1/2" 48" 12' 2.0 lbs/ft2

Exterior Soffit type X PG-11 5/8" 48" 8', 12' 2.3 lbs/ft2

Exterior Soffit type C type C 5/8" 48" 8', 12' 2.4 lbs/ft2

Packaging: 2 pieces per bundle, face-to-face, and end tapedEdge type: Tapered1 Represents approximate weight for design and shipping purposes. A more exact weight may be available for your

area; consult with your local PABCO® representative, or call PABCO® Technical Assistance.2 Other lengths may be available on a special order basis. Consult with your local PABCO® representative, or call

PABCO® Technical Assistance.

Product Data,Sizes and Types:

Page #25

Manufacturing: ASTM C 1396; www.astm.org Federal Specification SS-L-30D Type III, Grade X *Installation: Gypsum Association GA-216, www.gypsum.org ASTM C 840, www.astm.orgFire-Resistant Assemblies: Gypsum Association GA-600, Fire Design Manual Underwriters Laboratories, UL Fire Resistance Directory Surface Burning ASTM E 84; www.astm.orgCharacteristics: Flame Spread 15, Smoke Developed 0Non-Combustible: ASTM E 136, www.astm.org

“R” value: 1/2" = 0.45; 5/8" = 0.48 Thermal ResistanceVOC/Asbestos: Free of VOC (Volatile Organic Compound) & asbestosMaterial Safety Data Sheet: MSDS available at www.pabcogypsum.com, Technical DataPABCO Gypsum: “Construction Guide - Fire & Sound Rated Systems”Recycled Content: Refer to PABCO® Sustainable Materials Data Sheet for plant specific details.Please check our website at www.pabcogypsum.com for the latest edition of this specification.


Applicable Standards & Reference Documents:









tothe ®PABCO® Gypsum Specification PGS-008

ASTM specification C 1396

Limitations: • Shaftwall/Stairwell systems are designed as nonload bearing. (NLB)• Do not install in areas which will be adjacent to occupancies of unusually high moisture conditions.• Where penetrations occur in the assembly, additional reinforcement at corners may be required to distribute stress; approved flexible sealant/caulking may be required to seal around some penetrations. • Through penetrations are not allowed in area separation fire walls that are designed to collapse on the fire side.• Not recommended for use as an unlined HVAC supply shaft or duct.• Limiting heights and deflection criteria must be based upon the metal stud manufacturer’s recommendations.

PABCORE® SHAFTLINER type X panels are manufactured with a proprietary fire resistant type X core which has been reinforced with glass fibers and speciality additives to increase its fire-resistance. This core is encased in 100% recycled water-resistant face and back paper, and features a double beveled edge for ease of installation.

PABCORE® SHAFTLINER type X is distinguishable by the light green coloration of the water-resistant paper facing.

PABCORE® SHAFTLINER type X panels are designed for lining elevator, ventilation, and utility shafts, as well as constructing lightweight sound attenuation fire-resistant cavity shaft walls, and area separation fire walls in multifamily dwellings such as townhouses, condominiums, and apartments.

These panels are key components in PABCO® Shaftwall and Area Separation Fire Wall (ASFW) Systems utilizing C-H, C-T Studs or H-Studs. PABCO® Shaftwall Systems are easy to erect, achieving fire-resistance ratings of one and two hours. Both solid and cavity-type area separation walls provide Sound Transmission Class (STC) ratings that exceed model building code requirements with designs that achieve STC ratings in excess of 60.

Area Separation Fire Wall assemblies are light weight, weighing no more than 10 lbs/ft2 when constructed. As a result, the need for costly footings or foundation modifications are often eliminated. Due to the relatively light weight panels, they can be installed up to four (4) stories in height.

When used as an area separation wall, the system must be: ʶ Continuous from the foundation to the underside of the protected roof sheathing or continue through the roof to form a parapet.

ʶ Designed to allow for collapse of the construction on the side of the wall exposed to fire without collapse of the area separation fire wall.

Submittal 09 29 00

Page #28

PABCORE® SHAFTLINER


Description:

Primary Uses:

PABCORE® SHAFTLINER type X and PABCORE® MOLD CURB® Plus SHAFTLINER type X panels may be used in one and two-hour shaftwall systems, one and two-hour horizontal corridor ceiling systems and two-hour Area Separation Walls. Refer to the PABCO® Gypsum Shaftwall Systems publication for details.

Applicable Standards, Codes & Technical Data:

Submittal Approvals:

SJ 6-14-11/Shaftliner PABCO® Gypsum

Application:


Product Data,Sizes and Types:

Job name:

Contractor Date:

UL Core Type Thickness Width Length1 Edge Type Weight2

PG-10 1 inch 24 inches 8', 10',12' Double beveled 4.4 lbs/ft2

PABCORE® SHAFTLINER products are certified by a third-party inspection service. Each panel bears the UNDERWRITERS LABORATORIES, Inc. label to indicate CERTIFICATION of fire resistance, surface burning characteristics, and non-combustibility.1 Other lengths may be available on a special order basis. Consult with your local PABCO® representative, or call

PABCO® Technical Assistance.2 Represents approximate weight for design and shipping purposes. A more exact weight may be available for your

area; consult with your local PABCO® representative, or call PABCO® Technical Assistance.

Page #29

Manufacturing: ASTM C 1396; www.astm.org Federal Specification Type IV, Grade X*Installation: Gypsum Association GA-216, www.gypsum.org ASTM C 840, www.astm.orgFire-Resistant Assemblies: Gypsum Association GA-600, Fire Design Manual Underwriters Laboratories, UL Fire Resistance Directory Surface Burning ASTM E 84; UL: Fire Resistance DirectoryCharacteristics: Flame Spread 15, Smoke Developed 0Non-Combustible: ASTM E 136, www.astm.org

“R” value: 0.83 Thermal ResistanceVOC/Asbestos: Free of VOC (Volatile Organic Compound) & asbestosMaterial Safety Data Sheet: MSDS available at www.pabcogypsum.com, Technical DataPABCO Gypsum: “Construction Guide - Fire & Sound Rated Systems”Recycled Content: Refer to PABCO® Sustainable Materials Data Sheet for plant specific details.Please check our website at www.pabcogypsum.com for the latest edition of this specification.








tothe ®

Page #34



Description: PABCO® Regular Gypsum Wallboard is an interior gypsum board product with a fire-resistant, dimensionally stable, gypsum core. Each panel is encased in a 100% recycled paper on the face and back sides. The face paper is folded around the long edges to reinforce and protect the core; the ends are square cut and finished smooth. Long edges of panels are tapered providing a recessed area that allows joints to be reinforced and concealed with joint treatment creating a monolithic wall finish. High quality face paper manufactured by PABCO® Paper provides a smooth surface which can be decorated with paint, texture or wallpaper.

Primary Uses: PABCO® Regular Gypsum Wallboard products are utilized in non-structural wall, ceiling and partition applications, for use in new construction or renovation work. Both may also be used as a covering material for flat or curved surfaces.

Draft version B2 6-10-08

Reg SJones

Submittal 09 29 00

REGULARGypsum Wallboard

PABCO® Gypsum Specification PGS-001ASTM specification C 1396Available in MOLD CURB® Plus


PABCO® Gypsum endorses the Gypsum Association’s publications GA-216 and GA-214 as well as ASTM Standard Specification C 840 as its application and finishing specifications. These similar specifications give detailed instruction on the standard application of wallboard panels and proper joint finishing procedures. PABCO® Gypsum Wallboard panels may be attached to wood or steel framing with nails, screws and/or adhesives. Finishing of joints and covering fasteners is detailed in GA 214 and/or ASTM C 840.

A combination of nails on the perimeters and screws in the field of panels is permitted with the spacing the same as described for each type fastener. PABCO® Gypsum Wallboard panels shall be “cut to fit” as closely as possible without forcing panels in place. PABCO® Gypsum Wallboard joints shall not be aligned with door or window openings; joints shall be offset at least 6”. Temperature at time of panel application shall be above 40 degrees F and shall be maintained at 50 degrees F 48 hours prior to and during application and drying of joint compound. Special treatment of assemblies for additions such as control joints, resilient channel, insulation and perimeter relief systems shall be as specified in the tested system.

Application:

Advantages: •Costefficient,lightweight,andnon-combustiblecore.•Acceptsawiderangeofdecorativefinishes.•Consistentedgetapersproduceamonolithicflatsurface.•Easilycut,permittingquickinstallation,paintingand/ordecorating.•Negligibleexpansionandcontractionundernormalatmosphericchanges.

Limitations: PABCO® Regular Gypsum Wallboard panels are intended for interior applications and shall not be used where there will be direct exposure to water or continuous high humidity before, during, and/or after construction. Gypsum panel products shall not be exposed to sustained temperatures exceeding 125o F (52o C).

PABCO® Regular Gypsum Wallboard panels are non-structural, not to be used as a structural fastener base, or to support heavy wall or ceiling mounted objects. Installation to walls shall be with the bottom edge spaced a minimum of 1/4" inch (6 mm) above the floor.

Page #35 SJ-06-06-11/Regular PABCO® Gypsum


Submittal Approvals: Job name:Contractor: Date:

Applicable Standards and Technical Data:

Manufacturing: ASTM C 1396 Federal Specification SS-L-30D Type III & Type VII *Installation: Gypsum Association GA-214 & GA-216, www.gypsum.org ASTM C 840, www.astm.orgSurface Burning ASTM E 84Characteristics: Flame Spread 15, Smoke Developed 0Noncombustible: ASTM E 136“R” value: 1/2" = 0.45; 3/8" = 0.32 Thermal ResistanceVOC/Asbestos: Free of VOC (Volatile Organic Compound) & asbestosPABCO Gypsum: “Construction Guide - Fire & Sound Rated Systems”Foil Application: Foil may be applied to the back of ASTM C 1396 gypsum wallboard for the purpose of complying with ASTM C 1396 paragraph 5.1.Recycled Content: Refer to PABCO® Sustainable Materials Data Sheet for plant specific details.Please check our website at www.pabcogypsum.com for the latest edition of this specification. * The federal specification for gypsum board, SS-L-30d was withdrawn in 1984. It is provided here for informational purposes only.

Product Data:Sizes and Types

Core Thickness Width Length1 Weight2

Regular 1/4" 48" 8' 1.2 lbs/ft2

Regular 3/8" 48" 8' 1.5 lbs/ft2

Regular 1/2" 48" 8', 9', 10', 12', 14', 15' 1.6 lbs/ft2

Regular 1/2" 54" 10', 12' 1.6 lbs/ft2

Packaging: 2 pieces per bundle, face-to-face, and end labeled. Edge type: Tapered Material Safety Data Sheet: MSDS available at www.pabcogypsum.com, Technical Data1 Other lengths may be available on a special order basis. Consult with your local PABCO®

representative, or call PABCO® Technical Assistance.2 Represents approximate weight for design and shipping purposes. A more exact weight may be available

for your area; consult with your local PABCO® representative, or call PABCO® Technical Assistance.





Submittal 09 29 00 SUPER C FLAME CURB® - Pharos … · Non-Combustible: ASTM E 136, R value: ......

Documents

Transcript of Submittal 09 29 00 SUPER C FLAME CURB® - Pharos … · Non-Combustible: ASTM E 136, R value: ......