Sub-Surface Pump Accessories - RED. a design...

Sub-Surface Pump Accessories

HARBISON-FISCHER™

SubSurface Pump Access.indd 1 2/14/08 1:29:56 PM

Two Stage Hollow Valve Rod Pump

HARBISON-FISCHER™HARBISON-FISCHER™Q

UALI

TY


HARBISON-FISCHER™HARBISON-FISCHER™

�

A Global LeaderFounded in 1933 with a furnace, belt-drive machines and a Cadillac motor to turn the lathes, Harbison-Fischer has grown into a global leader committed to serving the sub-surface oilfield rod- pump market. Our technically trained, professional staff specializes in

– solving our customers’ downhole rod-pump problems;

– providing the highest quality products in a timely manner;

– creating value by providing service and expertise that lowers overall lifting costs;

– evaluating each well to recommend the appropriate pump configuration, pump metallurgy and operating parameters.

Located in thirty-five U.S. warehouses, three Canadian warehouses and throughout the oil-producing world, Harbison-Fischer maintains the largest on-hand inventory of rod-pump parts in the industry.


RUg

ged


HARBISON-FISCHER™

�

HARBISON-FISCHER™

Quik-Seal®

(shown with Flap-Tite® and Pro-Align®)

Injecta-Box®

RUg

ged

�



�

Injecta-Box® – Packing is injected directly into the stuffing

box through a check-valve-protected side injection port

– Safer and faster to pack than conventional stuffing boxes

– No adjustment is required due to the automatic piston adjustment feature

– Easily visible, external indicator pin shows when packing needs to be added

– Can be combined with the Harbison-Fischer Flap-Tite® and Pro-Align®

Quik-Seal®

– Innovative cone-seal stuffing box that seals tough wells

– Cone seals are inverted for better sealing

– Available in a stand-alone configuration or used in conjunction withthe Harbison-Fischer Flap-Tite® and Pro-Align®


RUg

ged


HARBISON-FISCHER™

��

HARBISON-FISCHER™dep

endAbLe

Harbison-Fischer Stuffing Boxes

High Temperature/ High Pressure

Pollution Control

�

Economy



�

Harbison-Fischer Stuffing Boxesproven, quality stuffing-box

designs for all well conditions

Pollution Control– Help control spills with two packoffs; primary and

secondary

– Indication of primary seal leakage through a port between the two seals, to operate a pressure switch or float valve

High Temperature/High Pressure– Rated to 450˚ Fahrenheit and 3,000 psi

– Easily adjust each packing with individual hammer nuts

– Saves time since lower packing can be tightened to seal pressure while changing upper packing

Economy– The most economical Harbison-Fischer

stuffing box

– Still comes with built-in Harbison-Fischer quality

– Uses easy-to-find industry-standard packing


RUg

ged

HARBISON-FISCHER™

�

HARBISON-FISCHER™

Harbison-Fischer Stuffing Boxes

Model DL

Model DS

dep

endAbLe

Model L

�

Model S



�

Model L– Minimizes down time due to dual packoffs.

Lower packing can be closed to hold pressure while upper packing is changed.

– Industry standard-size upper packing

– Lower “H” packing is easily sealed off with pressure from a standard grease gun and released with a screwdriver

Model DL– Slim-hole model of the legendary Model L

stuffing box

– Straightforward installation due to unique integration of flow tee (not shown)

Model S– More economical than the Model L box due

to not having the “H” seal, but uses the same industry-standard packing

– Used in lower-pressure wells that do not flow off when packing is replaced

Model DS– The economical version of the Model DL slim-hole

stuffing box

– Used in lower-pressure wells that do not flow off when packing is replaced, since it only has a primary packoff without “H” seal



Pro-Align®

Flap-Tite®

RUg

ged

�



�

Flap-Tite®

– A simple, dependable device that helps to control the well in case of a polished-rod break

– Flapper closes when polished rod breaks and falls below the valve

– Installs between the pumping tee and the stuffing box in a stand-alone installation or between the Pro-Align® and the Quik-Seal®

Pro-Align®

(Patent No. 6,585,416)

– Misalignment of the pumping unit is automatically corrected by allowing the stuffing box to conform to the working path of the polished rod (up to 1/2” in any direction and angular tilt up to 21/2° off center)

– Angular and horizontal misalignment can be corrected up to the limit of the tubing below the well head

– Packing life and polished-rod life are extended

– Identifies polished-rod movement that can result from pumping-unit geometry problems


HARBISON-FISCHER™

�0

HARBISON-FISCHER™

STR Tool (Stress and Torque

Reducing Tool)

RUg

ged

Sucker-Rod, Polished-Rod and

Combination Couplings

�0



STR Tool (Stress and Torque-Reducing Tool)

(Patent No. 4,963,078)

– Absorb sucker-rod-string shock loads above the pump with hydraulic action

– Hydraulic damping action on the pump upstroke and downstroke absorbs forces that could damage your rod string or pumping unit

– Resists corrosion due to 316 stainless steel construction

– Made with common sucker-rod threads

Sucker-Rod, Polished-Rod and Combination Couplings

Couple your rods with Harbison-Fischer quality

– Strict quality control and high-strength materials create the best couplings in the oil patch

– Threads are cold-formed for high-fatigue strength

– Two grades: Class “T” through hard or Class “SM” sprayed-metal coated available

Harbison-Fischer Couplings are manufactured to Harbison-Fischer design standards and ISO quality procedures and API specifications. They are available in all sucker-rod sizes in slim-hole and full-size diameters.

Harbison-Fischer Class T Sucker-Rod Couplings have a hardness of HRC 16-23 and are recommended for mildly-corrosive and mildly- abrasive pumping conditions.

Harbison-Fischer Tuffr® Couplings conform to API SM sucker-rod coupling specifications. The sprayed-metal surface hardness is HRC 58-62 and is ground smooth. Harbison-Fischer Tuffr® Sucker-Rod Couplings are recommended for corrosive and abrasive pumping conditions.

��


RUg

ged


��

HARBISON-FISCHER™

Polished RodsSTR

on

g &

VeR

SATI

Le

��


HARBISON-FISCHER™

Polished RodsQuality and high strength for

your rod string

– Connects your rod string to the prime mover

– Harbison-Fischer quality supports this highly- loaded rod

– Available in high-strength steels, stainless steel, or with a hard, long wearing Tuffr® sprayed-metal coating

All rods are manufactured to exceed API specifications.

piston Steel polished Rods are made from cold-drawn 1045 carbon steel with a minimum tensile strength of 100,000 psi. They are recommended for moderate to heavy loads when abrasion and corrosion are not factors.

nickel Moly polished Rods are machined from cold-drawn 4320 Nickel alloy steel with a minimum tensile strength of 100,000 psi. They are recommended for moderate to heavy loads under mildly corrosive conditions when abrasion is not a factor.

Tuffr® polished Rods are made from 1045 piston steel with a minimum tensile strength of 100,000 psi and a hard (HRC 48-52) sprayed-metal surface applied to the outside diameter. The length of the sprayed-metal surface is matched to the stroke length. They are recommended for abrasive and corrosive conditions under moderate to heavy loads.

Stainless Steel polished Rods are made from type 304 stainless steel with a minimum tensile strength of 75,000 psi. They are recommended for moderate loads under all corrosive conditions when abrasion is not a factor.

��


RUg

ged


HARBISON-FISCHER™

��

HARBISON-FISCHER™

Harbison-Fischer Polished Rod Clamps

Model 25

Model 13

Model 40

Model 13T

Model 13D

��

RUg

ged



Harbison-Fischer Polished-Rod Clamps

Harbison-Fischer quality and ruggedness for the tough jobs

Model 25– Easy-to-handle, rugged, single-bolt design for up

to 25,000 pounds loading

The Model 25 Polished-Rod Clamp is a one-bolt, rugged-design clamp for intermediate depth wells. It is rated to 25,000 pounds maximum working load.

Model 40– Simple, one-piece design with two large bolts

– Holds the polished rod in the deepest wells, up to 40,000 pounds load

The Model 40 Polished-Rod Clamp is a rugged, one-piece-design clamp with two large bolts for tightening the clamp to the rod. It is intended for use in deep wells and is rated for 40,000 pounds maximum working load.

Model 13– Economical design for shallow wells.

– Up to 13,000 pounds working load

The Model 13 Polished-Rod Clamp is a one-bolt clamp designed for shallow wells with less than 13,000 pounds maximum working load.

Model 13-D– Money-saving design that uses two factory-joined

Model 13 clamps

– Holds up to 26,000 pounds working load

Model 13-T– Economical choice like the Model 13-D, except

with three clamps

– Up to 40,000 pounds working load

��


HARBISON-FISCHER™

��

HARBISON-FISCHER™dep

endAbLe

Collet Fittings for Valve Rods or Pull Tubes

��

Polished Rod Liners



Polished-Rod LinersAdd a new face to your old

polished rod

– Slips over the existing polished rod while on the well, avoiding replacement of the polished rod

– Sprayed-metal surface gives longer life in corrosion or abrasion

The Harbison-Fischer Polished Rod Liner and integral pack-off assembly is a one-piece unit that is economical and efficient. It installs over the polished rod and provides a hard, smooth, sprayed-metal wearing surface.

Collet Fittings for Valve Rods or Pull Tubes

extend valve-rod or pull-tube life with a simple device

– Reduces stress by supporting the rod or tube along a longer length with a tight-fitting collet reducer

– High-strength steel or stainless steel available

Tough pumping conditions, such as downstroke friction or fast pumping speeds, can cause valve-rod or pull-tube breakage.

The Harbison-Fischer collet fittings provide a longer length of support for the valve rod or pull tube, which lessens the bending stress applied to the critical thread area of the rod or tube.

��


RUg

ged


HARBISON-FISCHER™

��

HARBISON-FISCHER™ReL

IAbLe

��

Tubing-Test Valve

Sucker-rod Hang-off Tool



Tubing-Test Valvedrop this assembly into your

seating-nipple-equipped tubing string for reliable pressure

testing

– Adaptable to your standard hold-down assembly

– Holds the pressure during testing and automatically releases the pressure when the fishing neck latch is pulled upward by wire line or sucker rods

The Harbison-Fischer Tubing-Test Valve is designed to be dropped into the tubing or lowered on a wire line to seat in a seating nipple for tubing-testing operations. It provides a positive check-valve seal that can release the pressure before unseating by pulling upward on the fishing neck latch at the top of the tool. It can be attached to any standard hold-down seal assembly.

Sucker-Rod Hang-off ToolAn elegant solution for the

need to temporarily hang off the sucker-rod string and seal

tubing pressure

– Facilitates hanging the sucker-rod string in the tubing with greater safety than homemade devices

– Threads onto the top sucker rod and the tubing threads in the flow tee to hold rods and seal pressure in the tubing

– Rugged design of solid steel and conforms to NACE specs for unhardened steel service

For certain operations where the sucker-rod pump is unseated and the rod string is hung in the tubing, the Harbison-Fischer Hang-off Tool (HOT) improves the safety of this procedure and provides a simple, effective method of sealing the tubing. The solid steel HOT tool has a built-in lifting sub for lifting the rod string. It is available in all popular tubing and sucker-rod sizes.

��


HARBISON-FISCHER™

�0

HARBISON-FISCHER™

Lift Sub

dep

endAbLe

Sinker Bars

�0



Sinker BarsWeight for your sucker-rod

string where it needs it most

– Overcomes problems with compressive loads at the bottom of rod strings

– Each end has heavy-duty sucker-rod pins

– Sinker bars are 25’ long and have an elevator relief

Harbison-Fischer Sinker Bars are manufactured from 1045 piston steel and provided with sucker-rod pins for a dependable makeup connection.

Lift SubAdd a lifting device

wherever it’s needed

– Gives a handling shoulder in a one-foot-long, heavy-duty sub

– Sucker-rod pins on each end for use on top of the sucker rod pump or polished rod

The Harbison-Fischer Lift Sub is a 1’ long handling sub with sucker-rod pins for use on top of the sucker-rod pump or polished rod. It is made from 1045 piston steel.

��


RUg

ged


HARBISON-FISCHER™

��

HARBISON-FISCHER™VeR

SATI

Le

Mechanical Seating Nipple

Sucker-Rod Pump Anchor

��



Mechanical Seating Nipplesgive your pump its best chance to seal off well fluids downhole

– Harbison-Fischer quality sets our seating nipples above any others

– Standard sizes for interchangeability

– Cup and mechanical types cover all well conditions

Harbison-Fischer Seating Nipples are made to API and industry inside-diameter and thread-size combinations. Configurations include cup and mechanical types in top and bottom hold-down styles.

Sucker-Rod Pump Anchorpark your pump anywhere

– Anchor an insert pump in tubing without a seating nipple

– Respond to variable fluid levels

– Can be set repeatedly without refurbishment

– Simple release by lifting upward on rod string

The Harbison-Fischer Sucker -Rod Pump Anchor is used to anchor an insert pump in a well that does not have a seating nipple or has variable fluid levels that require different seating depths. The tool can be run and set repeatedly without damage to the rubber-packing element. It is released by lifting upward on the sucker-rod string.

��



Strainer Nipples and Gas Anchors

Sucker-Rod Guides

��

RUg

ged



Strainer Nipples and Gas AnchorsKeep out big particles and/or

separate gas

– Strains large particles from the well stream

– Produce more fluid with a gas anchor/mud anchor setup to separate gas

Harbison-Fischer Strainer Nipples and Gas Anchors are made in steel and brass for use with insert and tubing pumps and are available in a variety of sizes.

Sucker-Rod Guides Reduce sucker-rod and

tubing wear with a choice of straightforward solutions

– Spiral Sucker-Rod Guide offers the longestwear-ing characteristics of any guide

– Renowned Harbison-Fischer Flexite® Sucker-rod Guide offers a 12” long, replaceable, long-lasting insert made of a special hard plastic composition material that is self-lubricating. Available in most sucker-rod and tubing sizes

– Guide can be installed in any location along the sucker rod string

Harbison-Fischer manufactures the Spiral Sucker-Rod Guide from alloy steel with a hard, smooth sprayed- metal coating on the outside for wear resistance.

The Flexite® Guide Insert can be replaced when worn. Both the Flexite® and Spiral Sucker-Rod Guides install between the sucker rods in place of a sucker-rod coupling.

��


RUg

ged


HARBISON-FISCHER™

��

HARBISON-FISCHER™Un

Co

MpRo

MIS

ed

��



��

ServiceHarbison-Fischer boasts a corporate philosophy that delivers uncompromised customer service at all times. From our 130-person field staff to our highly knowledgeable engineering staff, we

– support and problem-solve on a daily basis

– offer a level of expertise unmatched in the industry

– continually provide sales support

– teach technical schools in the field; and

– conduct regularly scheduled pump schools at our facility in Crowley, Texas

Quality ControlOur manufacturing equipment, already the most advanced in the industry, allows us to produce the highest-quality parts for our customers. Each product is backed by a quality system that has received both the ISO 9001:2000 and API Q1 certifications and the expertise of precision machine operators who have an average tenure of over 15 years with Harbison-Fischer.

Finally, to ensure that our customers receive the “Best PumPs in the Oil Patch”®, Harbison-Fischer has a fully-equipped metallurgical lab staffed by a degreed metallurgist. This department evaluates our products as raw material and work-in-process and, when needed, performs an analysis on any products sent back from the field. Additionally, the Research and Development department stays on the cutting edge of rod-pump technology by developing products in simulated downhole-operating environments.



HARBISON-FISCHER™HARBISON-FISCHER™Q

UALI

TY S

eRVIC

e

��



Harbison-Fischer is proud to be the industry leader in service,

quality and technology for more than seven decades.

��

The ever-recognizable orange color of Harbison-Fischer products is a registered trademark of the company.


901 North Crowley roadCrowley, texas 76036-3798

P.o. Box 2477 Fort worth, texas

76113-2477

PhoNe: 817-297-2211 Fax: 817-297-4248

www.hfpumps.com

HARBISON-FISCHER™

hF-2-08-5


Sub-Surface Pump Accessories - RED. a design...

Documents

Transcript of Sub-Surface Pump Accessories - RED. a design...