STI 34109 Installation Manual

Installation and Operation Manual

STI REPEATER

Thank you for purchasing this fine product. Your satisfaction is very important to us. Please read this manual carefully to get the most from your new product.

HOW THE PRODUCT WORKSSTI offers wireless products designed to alert you of several different conditions. The STI REPEATER is a 433 MHz radio signal receiver and transmitter that effectively doubles the transmission range of STI sensors to STI receivers. The REPEATER will filter out all radio signals that are not using 433 MHz STI protocol. When any STI protocol signal packet (except STI 8-Channel Receiver) is received, it transmits the same signal packet. There is no limit to the number of STI sensors that may be used with the STI REPEATER. It should be understood that multiple REPEATERS should NOT be used within reception range of each other because a REPEATER will simply retransmit any STI protocol signal packet (except 8-Channel Receiver). Two REPEATERS within reception range of each other can retransmit signal packets back and forth a few times when sensor packet is received. If a dual REPEATER system or further extended range applications are needed, please purchase STI 8-Channel Receivers (STI-34108). The receivers will retransmit alert and trouble notifications of the sensor signals, but not the actual signals themselves. Therefore, REPEATER feedback will not occur. The receivers work with up to 8 different STI wireless sensors.

BEFORE YOU STARTRefer to this drawing to become familiar with all the parts.

Model: STI-34109

2

ON BLINKING

GREEN LED AC/DC power on Signal Received

RED LED Low Battery Alert Signal Transmitted (only with AC/DC power on)

SPECIFICATIONS ExternalSupply:9-18VACorDC,15mAnominal(recommended30+mArating). Three(3)1.5VAAAAlkalinebatteries:externalpowerbackup(upto72hours). HousingDimensions:4x63/8x1in. Antennalengthwheninsertedinhousing:7in.

OPERATIONThe REPEATER receives distant STI protocol sensor signals and repeats the information to the receiver. Generally, STI sensors send 8 identical signal packets of information. The REPEATER rejects any signal that is not an STI protocol packet and retransmits the complete 8 packet set to the receiver.

STI REPEATERS wireless signals TamperSignaltamperswitchreleasedwhencoverisopenedordamaged TamperRestoreSignaltamperconditioncorrected LowBatterySignalbatterychargelow LowBatteryRestoreSignallowbatteryconditioncorrected SupervisorySignalsenteveryhourtomonitorthatREPEATERiswithinrange

REPEATER and sensor enrolling ThereceivercanmonitortheREPEATERSsupervisionandtroublesignalswhentheyareenrolled(ifdesired). TomanuallysendaREPEATERsignal,pressandreleasethetamperswitch.EnsuretheredLEDblinks. Toenrollsensors,followthereceiversprogramminginstructions.

LEDS

FEATURES Extendssystemrange. ReceivesandretransmitsdistantSTIprotocolwirelessdevicesignals(exceptforSTI8-ChannelReceivers

signals) to receivers. Sensorreprogrammingnotrequired. AllSTIprotocolalarm,supervisoryandtroublesignalsarerepeatedtoreceivers. REPEATERShavetheirownuniqueIDforsupervisory,tamperalertandlowbatterysignalsthatcanbe

monitored with receivers. Antennasincreaserangeforbothreceptionandtransmissionofsignals. Backupbatteryprotectsduringlossofexternalpower(upto72hours).

3

IMPORTANT NOTICEInformation and specifications are subject to change without notice.This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15oftheFCCRules.These limits are designed to provide reasonable protection against harmful interference in a residential installation.Thisequipmentgenerates,usesandcanradiateradiofrequencyenergyand,ifnotinstalledandused according to the instructions, may cause harmful interference to radio communications. However, there isnoguaranteethatinterferencewillnotoccurinaparticularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradioortelevisionreception,whichisfoundbyturningtheequipmentoffandon,theuserisencouragedtotrytocorrecttheinterferencebyoneormoreofthefollowingmeasures:- Reorient or relocate the receiving antenna -Increasetheseparationbetweentheequipmentordevices-Connecttheequipmenttoanoutletotherthanthereceivers-Consultadealeroranexperiencedradio/TVtechnicianforassistanceOperationissubjecttothefollowingtwoconditions:(1)thisdevicemaynotcauseinterference,and(2)this device must accept any interference, including interference that may cause undesired operation of the device. Changes or modifications not expressly approved by Safety Technology International, Inc. could void yourauthoritytooperatethisequipment.Toreducepotentialradiointerferencetootherusers,theantennatypeanditsgainshouldbesochosenthattheequivalentisotopicallyradiatedpower(e.i.r.p.)isnotmorethanthat permitted for successful communication. This product meets the applicable Industry Canada technical specifications.LeprsentmaterielestconformeauxspecificationstechniquesapplicablesdIndustrieCanada.FCCID:U5X-RE324IC:8310A-RE324

INSTALLATION GUIDEThe REPEATER is intended to be mounted indoors or in a waterproof environment. Review the APPLICATIONS GUIDE for suggested setups.1. Press the cover latch to remove top cover (do not lose tamper switch spring).2. RemovethePCBfrombottomcover. Usingthekeyholesonthebottomcoverasatemplate,markthetopandbottommountingholes.Locatethe

hole at least 1 foot away from the closest obstruction above.3. Drill3/16holes.4. Insert wall anchors, screws and washers (provided) and tighten to 1/8 gap.5. TURNOFFPOWERSUPPLY.Routepowersupplywiresfromtheside(recommended)orholefromtheback. a.Sideinstallationroutewiresthroughrightwireguideandthenleftwireguide.Removeknockoutonthe

top cover. b.Rearinstallationrunwiresthroughbackwireguideandthenleftwireguide.6. Placebottomcoverkeyholesontoscrewsandorientdevicevertical.7. Tightenscrews.8. On the PCB, insert the antennas into the outer antenna terminals marked ANTENNA. Tighten the antenna

terminal screws.9. SnapPCBintobottomcoversotheantennasareontheplasticstands.10. Remove the battery tab. The red LED blinks when the batteries are installed. If LED does not blink, press

and release the tamper switch. If LED still does not blink, replace batteries.11 .Insert12VoltACorDCpowersupplyleadsintotheterminalsmarkedAC/DC12V.Thepositiveand

negativeterminalshaveinterchangeablepolarity.Theymaybeorientedeither+/-or-/+.12.Turnonthepowersupply.ThegreenLEDturnson.IftheredLEDison,replacethe3AAAAlkaline

batteries.13. (If desired) Program the REPEATER and/or the sensors into the receiver (follow the receiver programming

instructions).ThereceivercanmonitortheREPEATERSsupervisionandtroublesignalswhenenrolled.To manually send a REPEATER signal, press and release the tamper switch. The red LED blinks when transmitting.

14. If the REPEATER or the sensors do not program properly, move the REPEATER mounting location closer to the receiver.

15.Latchthetopcoverinplace.Ensurethepowersupplywiresareroutedproperly.

4

Multiple Sensor/Receiver System (Figure 2)The REPEATER will receive and transmit any STI protocol signal packets received (except 8-Channel Receiver). Multiple sensors can be arranged to pass packets through the REPEATER to multiple receivers.

Up to1000 ft.

Up to1000 ft.

1 - MIRROR MASTER OFF/ON2 - NORMAL/ENROLL3 - AUTO RESTORE/LATCH4 - SIREN TIME/MIRROR#5 - SIREN TIME/MIRROR#6 - CHIME OFF/ON7 - NORMAL/DELETE8 - MIRROR SLAVE OFF/ON

SIREN SW4 SW5 TIME MIRROR # OFF OFF DISABLED 1ON OFF 30 SEC 2OFF ON 180 SEC 3ON ON ON CONT 4



Single Repeater System - General Use

Keep Repeater out of rangefrom non-repeater sensor

Multiple Sensor/Receiver System





Up to 1000 ft.to farthest sensor

Up to1000 ft.

Up to8 sensorsRepeater

Receiver #1

Receiver #2

Up to8 sensors

Extended Range System





Up to1000 ft.

Up to1000 ft.

Up to1000 ft.

Repeater

Receiver(Master)

Receiver(Mirrored)

System Range(Up to 6000 ft. span - with a full mirrored system

System with Distance between 2 Locations

Up to1000 ft.

Up to1000 ft. to

farthest sensor

Up to1000 ft. to

farthest sensorUp to

1000 ft.1 - MIRROR MASTER OFF/ON2 - NORMAL/ENROLL3 - AUTO RESTORE/LATCH4 - SIREN TIME/MIRROR#5 - SIREN TIME/MIRROR#6 - CHIME OFF/ON7 - NORMAL/DELETE8 - MIRROR SLAVE OFF/ON


Repeater RepeaterReceiver

Keep Repeater out of rangefrom each other





Receiver Receiver

System with Multiple Locations Monitored Centrally

Repeater Repeater

Repeater Repeater

Keep out of range

Keep out of range

Up to1000 ft. to

farthest sensor

Up to1000 ft. to

farthest sensor

Up to1000 ft.

Up to1000 ft.

Up to1000 ft.

Up to1000 ft.

Keep out of rangeKeep out of range

If 2 repeaters receive asignal from the samesensor, the signal will besent to the receiver 2 times.

Up to1000 ft. to

farthest sensor

Up to1000 ft. to

farthest sensor

Sensor

Out of rangesensor

In rangesensor

Repeater

Receiver

Figure 2

WARNINGSFORINDOORUSEONLY.Keepawayfromwaterordampareas.

WARRANTY INFORMATIONSafety Technology International, Inc. warrants to the original consumer/purchaser that this product shall be free of defects in material and workmanship under normal use and circumstances for a period of one (1) year from the original date of purchase.

Electronic warranty form at www.sti-usa.com/wc14.

APPLICATIONS GUIDECircle = sensor

General Use (Figure 1) sensors out of range Foroutofrangesensor(s),positionREPEATERbetweensensorandreceiver. Ifsomesensorsareinrangeofthereceiver,mounttheREPEATERclosertotheoutofrangesensor.The

REPEATER should not receive the in range sensor packets. IfitisnotpossiblefortheREPEATERtoreceiveoutofrangesensorswithoutalsopickingupinrangesensor

packets: Movethereceiverlocationforcinginrangesensorsoutofrange. PurchaseanSTI8-ChannelReceivertomirrortheoutofrangepacketstotheoriginal8-ChannelReceiver. Continuetousethereceiverasitis,allowingduplicatesensorpacketstobereceived.Thisshouldnot

change the receiver operation. Reconfiguresystem.

Up to1000 ft.

Up to1000 ft.













Up to1000 ft.


Receiver #1

Receiver #2

Up to8 sensors






Up to1000 ft.

Up to1000 ft.

Up to1000 ft.

Repeater

Receiver(Master)

Receiver(Mirrored)



Up to1000 ft.

Up to1000 ft. to

farthest sensor

Up to1000 ft. to










Receiver Receiver


Repeater Repeater

Repeater Repeater

Keep out of range

Keep out of range

Up to1000 ft. to

farthest sensor

Up to1000 ft. to

farthest sensor

Up to1000 ft.

Up to1000 ft.

Up to1000 ft.

Up to1000 ft.



Up to1000 ft. to

farthest sensor

Up to1000 ft. to

farthest sensor

Sensor

Out of rangesensor

In rangesensor

Repeater

Receiver

Figure 1

Central Monitoring of Multiple Locations (Figures 4 and 5)A receiver, or group of receivers, may be monitored in a central location between multiple REPEATERS as long as the REPEATERS are out of range from each other.

REPEATERFeedbackBecauseREPEATERSwillretransmitanySTIprotocolpacketsreceived(except8-Channel Receiver), if two REPEATERS are within reception range of each other they will send packets back and forth to each other. When using more than one REPEATER, keep them out of range from each other. An STI 8-Channel Receiver can be substituted for a REPEATER to eliminate this problem.

DualREPEATERReceptionIfmorethanoneREPEATERreceivesasignalpacketfromthesamesensor,bothREPEATERS will retransmit the packet. This should not be an issue, but the programmed receiver will then respond to both transmissions.

5

Up to1000 ft.

Up to1000 ft.













Up to1000 ft.


Receiver #1

Receiver #2

Up to8 sensors






Up to1000 ft.

Up to1000 ft.

Up to1000 ft.

Repeater

Receiver(Master)

Receiver(Mirrored)



Up to1000 ft.

Up to1000 ft. to

farthest sensor

Up to1000 ft. to










Receiver Receiver


Repeater Repeater

Repeater Repeater

Keep out of range

Keep out of range

Up to1000 ft. to

farthest sensor

Up to1000 ft. to

farthest sensor

Up to1000 ft.

Up to1000 ft.

Up to1000 ft.

Up to1000 ft.



Up to1000 ft. to

farthest sensor

Up to1000 ft. to

farthest sensor

Sensor

Out of rangesensor

In rangesensor

Repeater

Receiver

Up to1000 ft.

Up to1000 ft.













Up to1000 ft.


Receiver #1

Receiver #2

Up to8 sensors






Up to1000 ft.

Up to1000 ft.

Up to1000 ft.

Repeater

Receiver(Master)

Receiver(Mirrored)



Up to1000 ft.

Up to1000 ft. to

farthest sensor

Up to1000 ft. to










Receiver Receiver


Repeater Repeater

Repeater Repeater

Keep out of range

Keep out of range

Up to1000 ft. to

farthest sensor

Up to1000 ft. to

farthest sensor

Up to1000 ft.

Up to1000 ft.

Up to1000 ft.

Up to1000 ft.



Up to1000 ft. to

farthest sensor

Up to1000 ft. to

farthest sensor

Sensor

Out of rangesensor

In rangesensor

Repeater

Receiver

Figure 4

Figure 5

Extended Range System (Figure 3)The REPEATER may be used to extend the range of sensors to a multiple STI 8-Channel Receiver mirroring system.

Up to1000 ft.

Up to1000 ft.













Up to1000 ft.


Receiver #1

Receiver #2

Up to8 sensors






Up to1000 ft.

Up to1000 ft.

Up to1000 ft.

Repeater

Receiver(Master)

Receiver(Mirrored)



Up to1000 ft.

Up to1000 ft. to

farthest sensor

Up to1000 ft. to










Receiver Receiver


Repeater Repeater

Repeater Repeater

Keep out of range

Keep out of range

Up to1000 ft. to

farthest sensor

Up to1000 ft. to

farthest sensor

Up to1000 ft.

Up to1000 ft.

Up to1000 ft.

Up to1000 ft.



Up to1000 ft. to

farthest sensor

Up to1000 ft. to

farthest sensor

Sensor

Out of rangesensor

In rangesensor

Repeater

Receiver

Figure 3

Inst. Sht. STI-34109 DEC2012

ADDITIONAL WIRELESS ALERT SERIES PRODUCTSSTI-34098 SingleChannelSlaveReceiverSTI-34104 4-Channel ReceiverSTI-V34104 4-ChannelVoiceReceiverSTI-34108 8-Channel ReceiverSTI-34188 8-Zone Relay BoardSTI-34101 Solar Powered Driveway Monitor SensorSTI-34151 BatteryPoweredDrivewayMonitorSensorSTI-34201 WirelessMailboxAlertSensorSTI-34301 Wireless Garage Sentry SensorSTI-34401 WirelessUniversalAlertSensorSTI-34501 WirelessEntryAlertSensorSTI-34601 WirelessDoorbellButtonSTI-34701 IndoorWirelessPIRSTI-34752 OutdoorWirelessPIR

STI-6200WIR WirelessFireExtinguisherTheftStopperSTI-6200WIR4 WirelessFireExtinguisherTheftStopperw/ReceiverSTI-6400WIR WirelessExitStopperDoorAlarmSTI-6400WIR4 WirelessExitStopperDoorAlarmwithReceiverSTI-6517A WirelessStopperStationShieldwithSoundSTI-6517B WirelessStopperStationShieldwithSoundand TransmitterSTI-6517C StopperStationShieldwithWirelessTransmitterSTI-6517D WirelessStopperStationShieldwithButtonSound and TransmitterSTI-30104 Lamp ControllerSTI-30105 ExtendedAntennaSTI-34105 Voltamax12VDC(500mA)PowerSupplySTI-34106 KeyfobSTI-34109 Repeater

2306 Airport Rd Waterford, MI 48327Phone: 248-673-9898 Fax: 248-673-1246

[email protected] www.sti-usa.com

Safety Technology International (Europe) Ltd.Unit 49G Pipers Road Park Farm Industrial Estate Redditch

Worcestershire B98 0HU EnglandTel: 44 (0) 1527 520 999 Fax: 44 (0) 1527 501 999

E-mail: [email protected] Web: www.sti-europe.com

We protect the things that protect you.

STI 34109 Installation Manual

Documents

Transcript of STI 34109 Installation Manual