Standard Technical Data for the Horizontal Sliding ... · Slide Direction; Gate system can be set...
2
E N O H P S S E R D D A E M A N L I A M E P I Z , T S , Y T I C Y N A P M O C CUT-SHEET: HORIZONTAL MEZZANINE GATE; MODEL MGH Rev. Date: 111918 Page 1 of 2 Standard Technical Data for the Horizontal Sliding Mezzanine Gate 1. Mezzanine Gate Operation to be one of the following: a. Manual b. Electric; Electric drive system, 115 VAC, (24 VDC Secondary), 60 HZ, 1/3 HP. Operator control panel includes timer-to-close capability, obstruction sensing and one (1) three- button (Open-Stop-Close) control panel mounted push button station, and one (1) remotely located wall mount secondary 3-button push button. Includes Amber color WARNING strobe light, activates when gate is in operation. 2. Mounting Location on mezzanine to be one of the following: a. Deck Mount b. Face Mount 3. Gate Section; to be factory welded frame work with horizontal top rail. Includes mid-rail, 4” high toe board, 42” overall height, and vertical members not to exceed 8’ on center. Gate shall meet or exceed Federal OSHA standard for standard railings at the time of manufacture relative to dimensions and loading. To be fabricated from one of the following: a. Mild Steel b. 304-2b Stainless Steel c. 316L Stainless Steel 4. Rollers to be minimum 2-5/8” diameter, concealed within toe board. Rollers to be non-corrosive. 5. Slide Direction; Gate system can be set up for left or right slide direction during installation. See O&M Manual for Details. 6. Track, guides, brackets and mounts to be furnished in accordance with dimensional requirement of gate in lengths and sizes appropriate for handling and shipping. 5. Finish to be: a. Mild steel mezzanine gates; exposed surfaces to be Powder Coat Safety Yellow. Hardware/fasteners to be zinc plated. b. Stainless steel mezzanine gates (304-2b or 316L); mill finish, acid washed. Interfering welds ground smooth, not polished. Hardware/fasteners to be stainless steel. 6. Warranty to be One (1) Year from date of shipment, finish excluded. 7. Available Options: a. Remote controls; gate systems with electric controls only. b. Photoeyes; gate systems with electrical controls only c. Pull cord switch; gate systems with electric or pneumatic controls only. : s n o i s u l c x E 1. All electrical wiring or airline piping to and between all components by others. 2. Structural Review of mezzanine to accept loading and anchor design by others. 1150 S. 48TH STREET, GRAND FORKS, ND 58201 PHONE: 701.746.4519 | TOLL FREE: 877.446.1519 FAX: 701.746.8340 | WWW.PSINDUSTRIES.COM
Transcript of Standard Technical Data for the Horizontal Sliding ... · Slide Direction; Gate system can be set...
ENOHP SSERDDA EMAN
LIAME PIZ ,TS ,YTIC YNAPMOC
CUT-SHEET: HORIZONTAL MEZZANINE GATE; MODEL MGH
Rev. Date: 111918 Page 1 of 2
Standard Technical Data for the Horizontal Sliding Mezzanine Gate
1. Mezzanine Gate Operation to be one of the following:a. Manualb. Electric; Electric drive system, 115 VAC, (24 VDC Secondary), 60 HZ, 1/3 HP. Operator control panel includes timer-to-close capability, obstruction sensing and one (1) three-
button (Open-Stop-Close) control panel mounted push button station, and one (1) remotely located wall mount secondary 3-button push button. Includes Amber colorWARNING strobe light, activates when gate is in operation.
2. Mounting Location on mezzanine to be one of the following:a. Deck Mountb. Face Mount
3. Gate Section; to be factory welded frame work with horizontal top rail. Includes mid-rail, 4” high toe board, 42” overall height, and vertical members not to exceed 8’ on center. Gateshall meet or exceed Federal OSHA standard for standard railings at the time of manufacture relative to dimensions and loading. To be fabricated from one of the following:a. Mild Steelb. 304-2b Stainless Steelc. 316L Stainless Steel
4. Rollers to be minimum 2-5/8” diameter, concealed within toe board. Rollers to be non-corrosive.
5. Slide Direction; Gate system can be set up for left or right slide direction during installation. See O&M Manual for Details.
6. Track, guides, brackets and mounts to be furnished in accordance with dimensional requirement of gate in lengths and sizes appropriate for handling and shipping.
5. Finish to be:a. Mild steel mezzanine gates; exposed surfaces to be Powder Coat Safety Yellow. Hardware/fasteners to be zinc plated.b. Stainless steel mezzanine gates (304-2b or 316L); mill finish, acid washed. Interfering welds ground smooth, not polished. Hardware/fasteners to be stainless steel.
6. Warranty to be One (1) Year from date of shipment, finish excluded.
7. Available Options:a. Remote controls; gate systems with electric controls only.b. Photoeyes; gate systems with electrical controls onlyc. Pull cord switch; gate systems with electric or pneumatic controls only.
:snoisulcxE1. All electrical wiring or airline piping to and between all components by others.2. Structural Review of mezzanine to accept loading and anchor design by others.
1150 S. 48TH STREET, GRAND FORKS, ND 58201PHONE: 701.746.4519 | TOLL FREE: 877.446.1519FAX: 701.746.8340 | WWW.PSINDUSTRIES.COM
AS VIEWED FROM FLOOR BELOW (Deck mount shown, slide right operation)
ENOHP SSERDDA EMAN
LIAME PIZ ,TS ,YTIC YNAPMOC
CUT-SHEET: HORIZONTAL MEZZANINE GATE; MODEL MGH
Page 2 of 2
Quantity:
ID Operation1
M Manual
E Electric
ID Mounting Location (See Detail C)D Deck MountF Face Mount
ID Material/Finish M Mild Steel (Powder Coat Safety Yellow)S 304 Stainless Steel (Unfinished/Mill)L 316L Stainless Steel (Unfinished/Mill)
ID Nominal Opening Width 048 4' (48") 072 6' (72") - STOCK SIZE2
096 8' (96") - STOCK SIZE2
120 10' (120") 144 12' (144")
ID OPTIONS1 (Electric Controls Only)511322 Radio Control Kit; Keypad 502918 Add’l Transmitter; Keypad Qty: 501715 Switch; Ceiling Pull Cord 511756 Photoeye Kit (Electric)
DECK MOUNT
INTERMEDIATE ON GATES GREATER THAN
96” WIDE ONLY
PLAN VIEW
ELECTRIC OPERATOR (If Req’d)
FACE MOUNT
DETAIL C “Mounting Location”
Options
ELECTRIC OPERATOR (If Req’d)
MOUNTING DETAIL
STOP JAMB DETAIL
ELECTRIC OPERATOR (If Req’d)
(X") EXISTING OPENING SHROUD CLEARANCE
(EXHISTING OPENING PLUS 21”)
GUIDE BLOCK: GATE MOUNTED
FIELD FASTEN TO EXISTING RAILING (TYP). (FASTENERS BY OTHERS) BLOCK-OUT AS REQ’D.
FIELD FASTEN STOP JAMB TO EXISTING RAILING. (ANCHORS PROVIDED BY OTHERS). BLOCK-OUT AS REQ’D.
STOP JAMB
(If Req’d) GATE PULL HANDLE
FACE MOUNT TRACK: (EXISTING OPENING PLUS 6-3/8”)
SIDE VIEW (face mount shown)
3-3/4"
EXISTING RAILING
MANUAL RELEASE
LEVER (If Req’d)
5-15/16"
4-13/16”
42-5
/8”
2-3/
4” 3-13
/16”
4-1/16”
Slide Direction (As viewed from floor below)
Rev. Date: 111918
1150 S. 48TH STREET, GRAND FORKS, ND 58201PHONE: 701.746.4519 | TOLL FREE: 877.446.1519FAX: 701.746.8340 | WWW.PSINDUSTRIES.COM
SEE NOTE #3 BELOW
NOTES:1. See product Technical Data for details.2. Stock Gates are Mild Steel with Powder Coat YellowFinish.3. Gate components are shipped without directionbeing set. Set desired slide direction during installationusing instructions in O&M Manual.
### Custom _________ (inches)
