TECHNICAL CATALOGUE OF BKS SLIDING SYSTEM …access-novello.com/userfiles/product_files_shared/BKS...

TECHNICAL CATALOGUE OF BKS SLIDING SYSTEM WITHOUT/WITH THRESHOLD (8 and 10 mm)

1

CONTENTS1. BKS SLIDING SYSTEM OVERVIEW....................................................................................................................2. BKS SLIDING SYSTEM MANAGEMENT OF TAKING MEASURE.................................................................... 3. BKS SLIDING SYSTEM WITHOUT THRESHOLD CALCULATION................................................................... 3.1. GLASS CALCULATION GUIDE...........................................................................................................................3.2. BASE PROFILE CALCULATION METHOD........................................................................................................ 3.2.1 UPPER BASE PROFILE CALCULATION ...........................................................................................................3.2.2 LOWER BASE PROFILE CALCULATION .......................................................................................................... 3.3. GLASS SEAL CALCULATION GUIDE.................................................................................................................3.3.1 LENGTH CALCULATION OF INITIAL GLASS SEAL ........................................................................................ 3.3.2 LENGTH CALCULATION OF GLASS SEAL........................................................................................................ 3.4. SIDE COLUMN PROFILE CALCULATION METHOD....................................................................................... 3.5. LENGTH CALCULATION OF H TRANPARENT SEAL.......................................................................................3.6. FRAME PROFILE CALCULATION GUIDE........................................................................................................3.7. EXAMPLE OF CALCULATION............................................................................................................................4. PRODUCTION STEPS OF BKS SLIDING SYSTEM WITHOUT THRESHOLD.................................................4.1. NEEDED PARTS FOR INITIAL PANEL...............................................................................................................4.2. NEEDED PARTS FOR INTERMEDIATE PANEL................................................................................................5. PRODUCTION STEPS OF BKS SLIDING SYSTEMS WITHOUT THRESHOLD................................................5.1. INSTALLATED BKS SLIDING SYSTEM WITHOUT THRESHOLD....................................................................6. BKS SLIDING SYSTEM WITH THRESHOLD CALCULATION...........................................................................6.1. GLASS CALCULATION GUIDE...........................................................................................................................6.2. BASE PROFILE CALCULATION METHOD........................................................................................................ 6.2.1 UPPER BASE PROFILE CALCULATION ........................................................................................................... 6.2.2 LOWER BASE PROFILE CALCULATION ..........................................................................................................6.3. GLASS SEAL CALCULATION GUIDE.................................................................................................................6.3.1 LENGTH CALCULATION OF INITIAL GLASS SEAL ........................................................................................6.3.2 LENGTH CALCULATION OF GLASS SEAL........................................................................................................ 6.4. SIDE COLUMN PROFILE CALCULATION METHOD....................................................................................... 6.5. LENGTH CALCULATION OF H TRANPARENT SEAL....................................................................................... 6.6. FRAME PROFILE CALCULATION GUIDE........................................................................................................ 7. PRODUCTION AND ASSEMBLY STEPS OF BKS SLIDING SYSTEM WITH THRESHOLD............................8. SPECIFIC STAFF OF BKS SLIDING SYSTEM WITH THRESHOLD...............................................................8.1. NEEDED PARTS FOR INITIAL PANEL...............................................................................................................8.2. NEEDED PARTS FOR INTERMEDIATE PANEL................................................................................................ 9. INSTALLATED BKS SLIDING SYSTEM WITH THRESHOLD............................................................................

256677788899910111415161920202121212222222323232424252627

Bu izimin Verisine V018 Veri Dosyasndan Ulaabilirsiniz.

PUBLICATION DATE : 27.11.2015 REVISION NUMBER : 000DOCUMENT NUMBER : TP004-02 REVISION DATE : -

GLA

SS P

AN

ELS

HEIG

HT

GLASS PANELS WIDTH

2

1.BKS SLIDING SYSTEM OVERVIEW

GENERAL INFORMATION:

SLIDING SYSTEM WITH THRESHOLD SLIDING SYSTEM WITHOUT THRESHOLD

THE SLIDING SYSTEM DOESNT HAVE LIMIT OF GLASS PANELS. FOR SYSTEMS LONGER THEN 6 METER NUMBER OF PANELS CAN BE INCREASED BY THE ADDITION OF THE LOWER AND UPPER FRAME PROFILE.

MAXIMUM GLASS PANELS WIDTH : 1300 MMRECOMMENDED GLASS PANELS WIDTH : 1000 MMPANELS HEIGHT FOR 10 MM GLASS : 3000 MM PANELS HEIGHT FOR 8 MM GLASS : 3000 MM




AA

KESIT A-ALEK 1 : 10

INITIAL PANEL INITIAL

PANEL INTERMEDIATE

PANELMIDDLE PANEL

INTERMEDIATE PANEL

3

BKS SLIDING SYSTEM WITH THRESHOLD VIEW




INITIAL PANEL INITIAL

PANEL INTERMEDIATE

PANELMIDDLE PANEL

INTERMEDIATE PANEL

4

BKS SLIDING SYSTEM WITHOUT THRESHOLD VIEW




100

0

101

0

101

0

101

5

4000

5

2. BKS SLIDING SYSTEM MANAGEMENT OF TAKING MEASURE

TOP PARAPET

LASER

FLOOR

1. UPPER AND LOWER PARAPET ARE DEFINED USING CONSTRUCTION LASERS.2. MEASUREMENT SHOULD BE TAKEN WITH SAME LEVEL OF THE UPPER PARAPET OUTER EDGE.3. BOTTOM FRAME SHOULD BE MEASURED USING LASER REFER TO THE TOP OF THE PARAPET.

OPERATIONAL DEDUCTIBLE GAP IS 10 mm.

THE SYSTEM HEIGHT MUST BE TAKEN FROM THE TOP OF THE LOWEST POINT

NECESSARY DATA FOR THE BKS SLIDING SYSTEM :

LENGHT1.HEIGHT2.NUMBER OF PANELS3.PROFILE COLOR4.GLASS COLOR5.

TOP PARAPET

SIDE WALL

SIDE WALL

UP FRAME PROFILE

FLOOR

BOTTOM BASE

PROFILE

TOP PARAPET

FLOOR



100

0

101

0

101

0

101

5


875

508

AA

15,5 15,5 17 17 17 7 17 17 17

SYSTEM LENGHT = 4000

GLASS WIDTH=508

KESIT A-ALEK 1 : 10

2 PANELS PASS MIDDLE OF SYSTEM2 PANELS PASS2 PANELS PASS 2 PANELS PASS 2 PANELS PASS 2 PANELS PASS

RIGHT BEGINNING OF SYSTEM

LEFT BEGINNING OF SYSTEM

/

D

DE

KESIT D-D

SYS

TEM

HEI

GHT

= 1

000

GLA

SS H

EIG

HT =

875

DETAY ELEK 1 : 8

6

68,

5

9

DETAY FLEK 1 : 4

7,5

3

4

DETAY GLEK 1 : 4

3. BKS SLIDING SYSTEM WITHOUT THRESHOLD CALCULATION3.1. GLASS CALCULATION GUIDE:

EXAMPLE OF CALCULATION:FORMULA: GLASS WIDTH CALCULATION

SYSTEM LENGHT

4000 MM


15.5 MM


15.5 MM

CENTER OF SYSTEM

7 MM- - - +INTERSECTING

PANEL * 17 COUNT

6 x 17102 MM

FORMULA: GLASS HEIGHT CALCULATION

SYSTEM HEIGHT

1000 MM

LOWER FRAME

PROFILE HEIGHT

9 MM

DISTANCE BETWEEN LOWER FRAME

PROF. AND LOWER

BASE PROF.

6 MM

DISTANCE BETWEEN GLASS AND

68.5 MM

DISTANCE BETWEEN BEGINNING OF UPPER BASE PROFILE AND

BEGINNING OF UPPER FRAME

PROFILE

34 MM

GLASS HEIGHT

875 MM

ALT BAZA YK.

86.5 MM

ALT BAZA CAM YUVA

YK.

18 MM

AST BAZAYK.

13.5 MM

ST BAZA CAM YUVA

YK.

6 MM


BEGINNING OF UPPER BASE

PROFILE

7.5 MM- - - - =

SYSTEM HEIGHT

1000 MM - 125 MM GLASS HEIGHT875 MM-

=

6

PANEL NUMBER

8

ONE GLASSDIMENSION

508 MM=

GLASS DIMENSION



GLASS WIDTH CALCULATION TABLE

FOR THE RIGHT AND LEFT BEGINNING OF SYSTEM 15.5 MM

FOR THE CENTER OF SYSTEM 7 MM

FOR THE PANELS PASS 17 MM

875

508

KATLANIR CAM SSTEMLER


D

D

F

KESIT D-D

GLA

SS W

IDTH

=508

UPP

ER B

ASE

PRO

FILE

LEN

GTH

=491

8,5

DETAY FLEK 1 : 5

BAR CONJOINING

CAP

BAR CONJOINING

CAP

UPPER BASE

PROFILE

GLASS

8,5

DETAY GLEK 1 : 1

8,5

J

J

K

KESIT J-J

DETAY KLEK 1 : 5

LL

MKESIT L-L

GLASS WIDTH=508 BASE PROFILE LENGHT=497

DETAY MLEK 1 : 5

8,5

DETAY OLEK 2 : 5

2,5

DETAY PLEK 2 : 3

WW

XKESIT W-W


DETAY XLEK 1 : 5

8,5

DETAY YLEK 1 : 2

8,5

DETAY ZLEK 1 : 2

3.2.BASE PROFILE CALCULATION METHOD

7

FORMULA: UPPER BASE PROFILE LENGTH CALCULATION

GLASS WIDTH

508 MM

INNER SPACE OF THE BAR

CONJOINING CAP

8,5 MM

ITA BRLETRME

KAPAK INNER SPACE OF

THE BAR CONJOINING

CAP

8,5 MM

UPPER BASE PROFILE LENGTH

491 MM- - =

FORMULA: LOWER BASE PROFILE LENGTH CALCULATION

1.FOR THE INITIAL AND MIDDLE PANELS;

2.FOR THE INTERMEDIATE PANELS;

3.2.1.UPPER BASE PROFILE CALCULATION

3.2.2.LOWER BASE PROFILE CALCULATION


GLASS WIDTH

508 MM

INNER SPACE OF THE MIDDLE AND

SIDE COLUMN CAPS

8,5 MM

INNER SPACE OF THE

INTERMEDIATE BASE CAPS

2,5 MM

LOWER BASE PROFILE LENGHT

497 MM=- -

GLASS WIDTH

508 MM

INNER SPACE OF THE


8,5 MM

INNER SPACE OF THE


8,5 MM


491 MM=--

ST BAZA


TECHNICAL CATALOGUE OF BKS SLIDING SYSTEM WITHOUT/WITH THRESHOLD (8 and 10 mm)KATLANIR CAM SSTEMLER


L

L

K

K

M

KESIT K-K

GLA

SS H

EIG

HT =

875

ALU

M. S

EAL

LEN

GTH

=835

KESIT L-LLEK 1 : 9

GLA

SS H

EIG

HT =

875

INITI

AL

ALU

M. S

EAL

LEN

GTH

=832

.5

DETAY MLEK 1 : 9

24,

5

DETAY NLEK 1 : 3

18

DETAY OLEK 2 : 9

24,

5

DETAY PLEK 2 : 7

15,

5

DETAY QLEK 2 : 7

8

3.3.GLASS SEAL CALCULATION GUIDE3.3.1. LENGTH CALCULATION OF INITIAL GLASS SEAL

3.3.2. LENGTH CALCULATION OF GLASS SEAL

INITIAL ALUMINUM GLASS SEAL

GLASS HEIGHT

875 MM

GLASS GAP DIMENTION INTO BASE

PROFILE

18 MM

GLASS HEIGHT

875 MM

BASE INTERMEDIATE CAPS GAP

DIMENTION

15.5 MM

GLASS GAP DIMENTION INTO BAR

CONJOINING CAP

24.5 MM


CONJOINING CAP

24.5 MM

INITIAL ALUM.SEAL LENGTH

832.5 MM

ALUM.SEAL LENGTH

835 MM

- - =

ALUMINUM GLASS SEAL - - =

FORMULA: INITIAL ALUM. SEAL LENGTH CALCULATION

FORMULA: ALUM. SEAL LENGTH CALCULATION




SID

E C

OLU

MN

PRO

FILE

LEN

GHT

=940

SYS

TEM

HEI

GHT

= 10

00

51

9

3.4. SIDE COLUMN PROFILE CALCULATION METHOD

9

SYSTEM HEIGHT

1000 MM

LOWER BASE PROFILE HEIGHT

9 MM

UPPER BASE PROFILE HEIGHT

51 MM

SIDE COLUMN PROFILE LENGHT

940 MM- - =

3.6. FRAME PROFILE CALCULATION GUIDE LOWER FRAME PROFILE

UPPER FRAME PROFILE

AS MENTIONED IN PART TAKING MEASURES, FRAME PROFILE MUST BE CUT AS SYSTEM LENGTH.

3.5. LENGTH CALCULATION OF H TRANPARENT SEAL

H SEAL IS UTLZED AT EDGES OF 2 MIDDLE PANELS. H SEAL LENGTH IS THE SAME AS FOR AN INITIAL ALUMINUM SEAL.

H-SEAL

FORMULA: SIDE COLUMN CALCULATION




AA SYSTEM LENGHT = 4000

GLASS = 508

GLASS = 508

GLASS = 508

GLASS = 508 GLASS = 508

GLASS = 508

GLASS = 508

GLASS = 508

124

KESIT A-ALEK 1 : 10

PANELS COLLECTION WAY PANELS COLLECTION WAY

PANELS COLLECTION WAY

PANELS COLLECTION WAY

SYS

TEM

HEI

GHT

= 1

000

SID

E C

OLU

MN

PRO

FILE

LEN

GHT

= 9

40

ALU

M. S

EAL

LEN

GTH

= 8

35

IN

ITIA

L A

LUM

. SEA

L LE

NG

TH=8

32.5

LOWER BASE = 491 LOWER BASE = 497 LOWER BASE = 497

MIDDLE PANEL

MIDDLE PANEL

BB

KESIT B-BLEK 1 : 15

10

3.7.EXAMPLE OF CALCULATION

INTERMEDIATE PANEL

INTERMEDIATE PANEL

INTERMEDIATE PANEL

INTERMEDIATE PANEL

INITIAL PANEL

INITIAL PANEL

PANELS COLLECTION




8

8

8

11

4. PRODUCTION STEPS OF BKS SLIDING SYSTEM WITHOUT THRESHOLD

1.STEP

UPPER BASE PROFILE CUTTINGUPPER BASE

PROFILE

UPPER BASE PROFILE MEASURES WAS OBTAINED BY DESCRIBED FORMULA IN CHAPTER UPPER BASE PROF. CALCULATION. THEN, FOR EACH PANEL ONLY 1 PIECE CAN BE CUT.

LOWER BASE PROFILE CUTTING2.

STEP LOWER BASE PROFILE OF INITIAL AND MIDDLE PANELS ARE DIFFERENT AS DESCRIBED IN CHAPTER LOWER BASE PROF. CALCULATION. ACCORDING TO THE VALUES, FOR EACH PANEL IS CUT ONLY ONE PIECE.

LOWER BASE PROFILE

3.STEP

INITIAL ALUM. SEAL AND H-SEAL CUTTING

INTERMEDIATE SEAL CUTTING4.

STEP


SEAL CAN BE CUT REFER TO DESCRIBED FORMULA. INITIAL SEAL WILL BE INSTALLED ON INITIAL AND MIDDLE PANELS FROM THE OUTER EDGE

INTERMEDIATE SEAL CAN BE CUT REFER TO DESCRIBED FORMULA. THE SEAL WILL BE INSTALLED ON THE INTERMEDIATE PANELS FROM THE INNER EDGE.

ALUMINUM GLASS SEAL

H-SEAL

H SEAL LENGTH IS THE SAME AS FOR AN INITIAL ALUMINUM SEAL.



8

8

8


AB

DETAY ALEK 1 : 5

UPPER BASE

PROFILDETAY B

LEK 1 : 2

DETAY CLEK 1 : 2

D

DETAY DLEK 1 : 5

E

DETAY E

ST BAZA

ALT BAZA

CAM CAM

F

DETAY F

ST BAZA

ALT BAZA

G

DETAY GLEK 1 : 5

UPPER BASE PROFIL

BAR CONJOINING

CAP

DETAY HLEK 2 : 5

BAR CONJOINING

CAP

J

L

DETAY JLEK 1 : 5

LOWER BASE

PROFILE

INTERMEDIATE COVER

DETAY KLEK 1 : 3

INITIAL AND MIDDLE COVERS

M

DETAY MLEK 1 : 3

12

5.STEP

HOW TO INSTALL UPPER WHEEL TO UPPER BASE PROFIL

AT EACH UPPER BASE PROFILE AT THE EDGES UPPER WHEELS ARE MOUNTING. ONLY AFTER BAR CONJOINING CAP INSTALLATION, IT CAN BE TIGHTENED.

6.STEP

ST BAZA VE ALT BAZANIN CAMA TAKILMASI

ST BAZA VE ALT BAZA CAM YAPITIRICI YARDIMI LE CAMA MONTE EDLR.

UPPER WHEEL

UPPER WHEEL

HOW TO INSTALL BAR CONJOINING CAP TO BASE PROFIL

BAR CONJOINING CAPS TAKE PLACE ON THE UPPER BASE PROFILE END. CAPS ARE TIGHTENED WITH ALLEN WRENCH. AFTER INSTALL THE BAR CONJOINING CAP UPPER WHEELS CAN BE SCREWED TOO.

7.STEP

INITIAL AND MIDDLE CAPS INSTALLATION

INITIAL AND MIDDLE CAPS ARE MOUNTING TO THE INITIAL AND MIDDLE PANELS FROM ITS OUTSIDE BOTTOM CORNERS. NOW THIS CAPS CAN BE SCREWED TO BOTTOM BASE PROFILE

HOW TO INSTALL INTERMEDIATE CAPS TO BASE PROFIL

INTERMEDIATE CAPS ARE MOUNTING TO THE FOLLOWING PANELS FROM ITS BOTTOM CORNERS. NOW THIS CAPS CAN BE SCREWED TO BOTTOM BASE PROFILE


UPPER WHEEL

UPPER WHEEL



A

DETAY A

CAM

E

H

J

OO

R

KESIT O-O

T

DETAY TLEK 1 : 7

INTERMEDIATE COVER

LOWER BASE PROFILE

BOTTOM WHEEL

V

DETAY VLEK 1 : 5

BOTTOM WHEEL

W

DETAY WLEK 1 : 8

ALUMINUM GLASS SEAL

ALUMINUM GLASS SEAL

UPPER BASE PROFILE

LOWER BASE PROFILE

X

DETAY XLEK 1 : 2

BRUSH SEAL

INTERMEDIATE ALUMINUM SEAL

13

8.STEP

10.STEP

BOTTOM WHEELS SLIDE ON LOWER BASE PROFILE UNTIL INTERMEDIATE CAPS, AS SHOWN ON DRAWING. THEN ITS SCREWED.

CAM FTL

BALANGICAM FTL

BOTTOM WHEEL INSTALLATION

UPPER LOWER BASE PROFILE AND ALUMINUM SEAL INSTALLATION TO GLASS

LOWER BASE PROFILE IS GLUED TO GLASS.

PREPARED ALUMINUM SEAL WITH BRUSH SEAL ARE MOUNTED TO THE GLASS PANEL .IT MUST REACH TO CONJOINING BAR.

INSTEAD OF ALUMINUM SEAL, H-SEAL IS MOUNTED ON THE MIDDLE PANELS OPPOSITE EDGES.

BRUSH SEAL IS CUT TO LENGTH OF THE UPPER BASE PROFILE, AND INSERTS INTO IT.

BRUSH SEAL IS CUT TO LENGTH OF THE ALUMINUM SEA UNTIL CONJOINING BAR, AND INSERTS INTO IT.

9.STEP

BRUSH SEAL INSTALLATION TO UPPER BASE PROFILE OR ALUMINUM SEAL

GLASS


1

2 2

3

UPPER BASE PROFILE IS GLUED TO GLASS.



W.6811

W.6826W.6826

W.6810

A

B

DETAY ALEK 1 : 2

DETAY BLEK 1 : 2

CC

KESIT C-C

14

4.1. NEEDED PARTS FOR INITIAL PANEL

GLASS

W.6811UPPER BASE PROFILE

ONLY ONE PIECE IS USED AT EACH GLASS PANEL

FROM SYSTEM TOP.

W.6813INITIAL ALUMINUM

SEAL

ITS USED ON THE OUTER EDGES OF INITIAL PANELS

AS INSULATION.

W.6812INTERMEDIATE ALUMINUM SEAL

ITS USED BETWEEN GLASS PANLES AS

INSULATION

W.6821UPPER WHEEL

ITS MOUNTED ON THE EACH EDGE OF THE

UPPER GLASS PROFILE, ENSURING BALANCE OF

THE SYSTEM.

W.6826BAR CONJOINING CAP

ITS MOUNTED ON THE EACH TOP EDGE OF THE GLASS PANEL.

W.6820BOTTOM WHEEL

ITS MOUNTED ON THE EACH EDGE OF THE LOWER GLASS PROFILE, PROVIDING

MOTION OF THE PANELS.

W.6824MIDDLE AND INITIAL

CAPS

ITS INSTALLED ON THE LOWER BASE PROFILE

AT THE END OR MIDDLE POINTS.

W.6823INTERMEDIATE BASE

CAPS

ITS MOUNTED ON THE LOWER BASE PROFIL IN ORDER TO DRAG

THE PANELS.

W.6810BOTTOM BASE PROFILE

ONLY ONE PIECE IS USED AT EACH GLASS PANEL FROM SYSTEM BOTTOM.

NEEDED PARTS OF MIDDLE AND INITIAL PANELS ARE SAME, EXCEPT AN INITIAL SEAL. INSTEAD OF INITIAL SEAL AT THE MIDDLE PANEL H-SEAL IS USED.

W.6813W.6812

W.6823W.6824

W.6820 Bu izimin Verisine V018 Veri Dosyasndan Ulaabilirsiniz.

W.6821W.6821

W.6820



W.6823W.6823

W.6812

W.6812

W.6826

W.6826

W.6811

W.6810

GLASS

B

C

DETAY BLEK 1 : 3

DETAY CLEK 1 : 3

15

4.2. NEEDED PARTS FOR INTERMEDIATE PANEL

W.6821W.6821

W.6820W.6820





FROM SYSTEM TOP.

W.6810BOTTOM BASE PROFILE

ONLY ONE PIECE IS USED AT EACH GLASS PANEL FROM SYSTEM BOTTOM.



INSULATION

W.6821UPPER WHEEL



THE SYSTEM.



W.6820BOTTOM WHEEL




CAPS


THE PANELS.


A

DETAY ALEK 1 : 20

SIDE COLUMNPROFILE

LOWER FRAME PROFILE

SIDE COLUMNPROFILE

UPPER FRAME PROFILE

BC

DETAY BLEK 1 : 6

LOWER FRAME PROFILEBOTTOM SIDE

COLUMN EQUIPMENT

DETAY CLEK 1 : 6

LOWER FRAME PROFILE

BOTTOM SIDE COLUMN

EQUIPMENT

DE

DETAY DLEK 1 : 8

UPPER SIDE COLUMN

EQUIPMENT

DETAY ELEK 1 : 8

SIDE COLUMNPROFILE

UPPER SIDE COLUMN

EQUIPMENT

F

DETAY FLEK 1 : 6

I

DETAY ILEK 1 : 5

J

DETAY JLEK 1 : 8

SIDE COLUMNPROFILE

16

5. PRODUCTION STEPS OF BKS SLIDING SYSTEMS WITHOUT THRESHOLD

1.STEP

2.STEP

THE SIDE COLUMN PROFILES ARE MOUNTED TO THE LOWER FRAME PROFILE BY BOTTOM SIDE COLUMN EQUIPMENT.

TOP FRAME PROFILE IS MOUNTED TO SIDE COLUMN PROFLE BY TOP SIDE COLUMN EQUIPMENT.

1

2

2

3

3

INSTALLATON CAN BE MADE EASIER IF ONE OF THE BASE INTERMEDIATE FLAT COVER AND LOWER WHEEL IS REMOVED. NOW THIS WHEEL CAN BE FIXATE TO THE BOTTOM FRAME RPOFILE.

ALT TEKER

ALT BAZA

BAZA ARA KAPAI

ALT TEKER

LOWER FRAME PROFILE


2

1

3AFTER SYSTEM NSTALLATION, TOP FRAME PROFILE

IS FIXED TO TOP PARAPATE AND BOTTOM FRAME PROFILE IS FIXED TO NETHER FLOOR WITH GLUE.4

FOR THE SYSTEM INSTALLATION LOWER FRAME PROFILE MUST BE PLACED ON A FLAT FLOOR.

ALTERNATVE 1

ALTERNATVE 2

TOP SIDE COLUMN APARATUS S FIXATED TO TOP FRAME PROFILE. TOP FRAME IS FICATED TO TOP PERAPETE WITH SCREW. TOP FRAME AND SIDE COLUMN APARATUS ARE MOUNTED WITH TOP SDE COLUMN APARATUS. AT THE SAME TIME SIDE COLUMNS AND LOWER FRAME INSTALLATION IS DONE WITH LOWER SIDE COLUMN APARATUS

BOTTOM WHEEL



A

DETAY ALEK 1 : 15

E

E

15-

20 M

M

KESIT E-ELEK 1 : 11

GII

JKESIT I-I

DETAY JLEK 1 : 11

L

DETAY LLEK 1 : 11

INTERMEDIATE COVER

2.PANEL

1.PANEL

DETAY MLEK 2 : 15

INTERMEDIATE COVER

N

DETAY NLEK 1 : 3

SCREW DIRECTION

RETURN WAY OF PANEL

O

DETAY OLEK 1 : 3

17

3.STEP

YOU SHOULD START INSTALLATION FROM ONE SIDE OF SYSTEM. THE TOP WHEEL OF THE PANELS IS PASSED TO TOP FRAME POFILE. ROM CAPS SIDE IN ORDER TO PROVIDE THE CONVENIENCE INSTALLATION, BOTTOM WHEEL PASSES THROUGH BOTTOM BASE PROFILE. BASE INTERMEDIATE COVER IS SCREWED TO THE BASE.

AFTER PANELS CONNECTED TO THE SYSTEM, BETWEEN THE TOP CASE AND TOP WHEEL TOLERANCE WLL BE 15-20 MM.

4.STEP

BOTTOM WHEEL

BOTTOM WHEEL

BAZA ARA KAPAI VE ALT TEKERLER ALT BAZADAN SKLR.


YOU CAN ADJUST GAPS BETWEEN THE GLASS PANELS BY USING WHEELS AS SHOWN AT THE PICTURE BELOW.

WHILE SECOND PANEL INSTALLATION IT MUST BE IN THE MIDDLE OF FIRST PANEL AS SHOWN N DRAWING. THEN INTERMEDIATE CAPS AND WHEELS CAN BE MOUNTED TO BOTTOM BASE PROFILE. FOR THE FUTHER PANELS PROCESS OF CAPS AND WHEELS MONTAGE IS SHOWN AT STEPS 5 AND 6.



B

DETAY BLEK 1 : 5

SRME KIL FTL

CAM FTL PROFL

CAM FTL PROFL

MIDDLE PANEL

INITIAL PANEL

INITIAL PANEL

E

F

DETAY ELEK 1 : 11

BALANGI KANADI

DETAY FLEK 1 : 8

LOCK FASTENERS

LOCK

DETAY GLEK 1 : 6

LOCK FASTENERS

LOCK

I

DETAY ILEK 1 : 4

J

10

DETAY JLEK 1 : 2

K

R

DETAY KLEK 1 : 3

L

14

DETAY LLEK 1 : 2

M

DETAY MLEK 1 : 2

NN

O

KESIT N-N

DETAY OLEK 1 : 3

IT CAN BE INSTALLED AT INITIAL PANELS INTO SIDE COLUMN

IT CAN BE INSTALLED AT MIDDLE PANELS

IT CAN BE INSTALLED AT INITIAL PANELS OUTSIDE OF SIDE COLUMN

SEMIFINISHED CODE:Y.6822.01



P

DETAY PLEK 1 : 5

Q

DETAY QLEK 1 : 5

DETAY RLEK 1 : 8

LOCK

LOCK FASTENERS

S

T

DETAY SLEK 1 : 9

DETAY TLEK 1 : 8

18

7.ADIM6.ADIM

SRME KIL FTL TAKILAN CAM FTL PROFLLER KANATLARA TAKILIR. CAM FTLLER NCE ITA BRLETRME KAPAINA TAKILIR DAHA SONRA BAZA ARA KAPAINA VEYA ORTA VE YANDKME KAPAINA TAKILIR.

ORTADAK KANATLARIN BRBRNE BAKAN KISIMLARINA CAM FTL PROFLLER YERNE EFFAF H FTL TAKILIR.

SRME KIL FTL, CAM FTL PROFL LSNDEN ITA BRLETRME KAPAINA GEECEK KADAR UZUN KESLR. CAM FTL PROFLLERNE SRME KIL FTLLER TAKILIR. SRME KIL FTL TAKILDIKTAN SONRA UZUN OLAN PARASI KESLR.

5.STEP

BKS SLIDING SYST. LOCK IS MOUNTED ON THE MIDDLE AND INITIAL PANELS. LOCK FASTENERS IS DIFFERENT FOR TWO TYPE OF PANEL. BELOW YOU CAN FIND CODE OF FASTENERS.

ON ONE SIDE OF MIDDLE PANEL THE LOCK IS MOUNTED, ON OPPOSITE SIDE FASTENERS IS SCREWED.LOCK AND FASTENERS ARE MOUNTED TO THE SIDE COLUMN PANEL DEPENDING ON THE SYSTEM FORM.

INITIAL PANEL MAY CONCDE BETWEEN SDE COLUMNS OR IT MAY CAINCIDE EDGE OF SIDE COLUM. THIS TWO EXPLANATIONS ARE GVEN IN THE PICTURE.

CAM FTL PROFL


1-DOOR LOCK IS USED AS AN ALTERNATIVE LOCK AT MIDDLE PANELS.

2-DOOR LOCK IS USED AS AN ALTERNATIVE LOCK AT MIDDLE PANELS. IT CAN BE LOCKED FROM

INSIDE AND OUTSIDE

OR



UPPER FRAME PROFILE

INITIAL PANEL

INITIAL PANEL

MIDDLE PANEL MIDDLE

PANEL

INTERMEDIATE PANEL INTERMEDIATE PANEL

INTERMEDIATE PANEL INTERMEDIATE

PANEL

SIDE COLUMN PROFILE

SIDE COLUMN PROFILE

BOTTOM BASE

PROFILE

BB

KESIT B-BLEK 1 : 10

5.1 INSTALLATED BKS SLIDING SYSTEM WITHOUT THRESHOLD

19

LOCKLOCK

LOCK

H-SEALALUMINUM GLASS SEAL




508

848

AA

15,5 15,5 17 17 17 7 17 17 17

SYSTEM LENGHT = 4000 GLASS WIDTH=508

KESIT A-ALEK 1 : 10

2 PANELS PASS MIDDLE OF SYSTEM2 PANELS PASS2 PANELS PASS 2 PANELS PASS 2 PANELS PASS 2 PANELS PASS

RIGHT BEGINNING OF SYSTEMLEFT BEGINNING OF SYSTEM

/I

I

J

KESIT I-I

SYS

TEM

HEI

GHT

=100

0 G

LASS

HEI

GHT

=848

DETAY JLEK 1 : 8

7,5

34

DETAY LLEK 1 : 4

42

68,

5

DETAY MLEK 1 : 4

6. BKS SLIDING SYSTEM WITH THRESHOLD CALCULATION6.1.GLASS CALCULATION GUIDE :

EXAMPLE OF CALCULATION:FORMULA: GLASS WIDTH CALCULATION

SYSTEM LENGHT

4000 MM


15.5 MM


15.5 MM

CENTER OF SYSTEM

7 MM- - - +

(PANEL SAYISI - 2) x 176 x 17

102 MM

=ONE GLASSDIMENSION

508 MM

FORMULA: GLASS HEIGHT CALCULATION

SYSTEM HEIGHT

1000 MM

LOWER FRAME PROFILE HEIGHT

42 MM

DISTANCE BETWEEN BOTTOM FRAME

PROFILE AND LOWER GLASS SURFACE

68.5 MM

DISTANCE BETWEEN BEGINNING OF UPPER BASE PROFILE AND

BEGINNING OF UPPER FRAME

PROFILE

34 MM

GLASS HEIGHT

848 MM

ALT BAZA YK.

86.5 MM

ALT BAZA CAM YUVA

YK.

18 MMAST BAZA

YK.

13.5 MM

ST BAZA CAM YUVA

YK.

6 MM


BEGINNING OF UPPER BASE

PROFILE

7.5 MM

- - - =SYSTEM HEIGHT

1000 MM - 152 MM GLASS HEIGHT848 MM

-=

20

INTERSECTING PANEL * 17 COUNT

6 x 17102 MM

PANEL NUMBER

8

GLASS DIMENSION



GLASS WIDTH CALCULATION TABLE

FOR THE RIGHT AND LEFT BEGINNING OF SYSTEM 15.5 MM

FOR THE CENTER OF SYSTEM 7 MM

FOR THE PANELS PASS 17 MM



D

D

F

KESIT D-D

GLA

SS W

IDTH

=508

UPP

ER B

ASE

PRO

FILE

LEN

GTH

=491

8,5

DETAY FLEK 1 : 5

BAR CONJOINING

CAP

BAR CONJOINING

CAP

UPPER BASE

PROFILE

GLASS

8,5

DETAY GLEK 1 : 1

8,5

J

J

K

KESIT J-J

DETAY KLEK 1 : 5

LL

MKESIT L-L


DETAY MLEK 1 : 5

8,5

DETAY OLEK 2 : 5

2,5

DETAY PLEK 2 : 3

WW

XKESIT W-W


DETAY XLEK 1 : 5

8,5

DETAY YLEK 1 : 2

8,5

DETAY ZLEK 1 : 2

6.2.BASE PROFILE CALCULATION METHOD

21

GLASS WIDTH

508 MM

INNER SPACE OF THE BAR

CONJOINING CAP

8,5 MM

ITA BRLETRME

KAPAK INNER SPACE OF

THE BAR CONJOINING

CAP

8,5 MM

UPPER BASE PROFILE LENGTH

491 MM

- - =


1.FOR THE INITIAL AND MIDDLE PANELS;

2.FOR THE INTERMEDIATE PANELS;

6.2.1. UPPER BASE PROFILE CALCULATIONI

6.2.2.LOWER BASE PROFILE CALCULATION


GLASS WIDTH

508 MM

INNER SPACE OF THE MIDDLE AND

SIDE COLUMN CAPS

8,5 MM

INNER SPACE OF THE


2,5 MM


497 MM=- -

GLASS WIDTH

508 MM

INNER SPACE OF THE


8,5 MM

INNER SPACE OF THE


8,5 MM


491 MM=--

ST BAZA



FORMULA: UPPER BASE PROFILE LENGTH CALCULATION



L

L

K

K

M

KESIT K-K

GLA

SS H

EIG

HT =

848

MID

DLE

ALU

M. S

EAL

LEN

GTH

=808

KESIT L-LLEK 1 : 9

GLA

SS H

EIG

HT =

848

INITI

AL

ALU

M. S

EAL

LEN

GTH

=805

.5

DETAY MLEK 1 : 9

24,

5

DETAY NLEK 1 : 3

18

DETAY OLEK 2 : 9

24,

5

DETAY PLEK 2 : 7

15,

5

DETAY QLEK 2 : 7

22

6.3. GLASS SEAL CALCULATION GUIDE6.3.1. LENGTH CALCULATION OF INITIAL GLASS SEAL

6.3.2. LENGTH CALCULATION OF GLASS SEAL


GLASS HEIGHT

848 MM

GLASS GAP DIMENTION INTO BASE

PROFILE

18 MM

GLASS HEIGHT

848 MM

BASEINTERMEDIATE

CAPS GAP DIMENTION

15.5 MM


CONJOINING CAP

24.5 MM


CONJOINING CAP

24.5 MM

INITIAL ALUM. SEAL LENGTH

805.5 MM

MIDDLE ALUM. SEAL LENGTH

808 MM

- - =

ALUMINUM GLASS SEAL - - =

FORMULA: ALUM. SEAL LENGTH CALCULATION

FORMULA: INITIAL ALUM. SEAL LENGTH CALCULATION




SYSTEM LENGHT=4000

BOTTOM BASE LENGTH=3980

UPPER FRAME LENGTH=4000

BC

10

DETAY BLEK 1 : 15

LOWER FRAME PROFILE

SIDE COLUMN PROFILE

BOTTOM SIDE COLUMN EQUIPMENT

10

DETAY CLEK 1 : 9

LOWER FRAME PROFILE

SIDE COLUMN PROFILE

BOTTOM SIDE COLUMN

EQUIPMENT

D

DETAY DLEK 1 : 10

E

928

100

0

22

51

DETAY ELEK 1 : 10

23

LOWER FRAME PROFILE

SYSTEM LENGHT

4000 MM

BOTTOM SIDE COLUMN

EQUIPMENT WIDTH

10 MM

BOTTOM SIDE COLUMN

EQUIPMENT WIDTH

10 MM

LOWER FRAME PROFILE HEIGHT

3980 MM=--

6.4. SIDE COLUMN PROFILE CALCULATION METHOD

6.5. LENGTH CALCULATION OF H TRANPARENT SEAL

H SEAL IS UTLZED AT EDGES OF 2 MIDDLE PANELS. H SEAL LENGTH IS THE SAME AS FOR AN INITIAL ALUMINUM SEAL.

6.6. FRAME PROFILE CALCULATION GUIDEAS MENTIONED IN PART TAKING MEASURES, FRAME

PROFILE MUST BE CUT AS SYSTEM LENGTH.

H-SEAL

SYSTEM HEIGHT

1000 MM

BOTTOM SIDE COLUMN

EQUIPMENT HEIGHT

22 MM

UPPER BASE PROFILE HEIGHT

51 MM

SIDE COLUMN PROFILE LENGHT

928 MM=--

FORMULA: SIDE COLUMN CALCULATION




24

7. PRODUCTION AND ASSEMBLY STEPS OF BKS SLIDING SYSTEM WITH THRESHOLD

PRODUCTION STEPS FOR SLIDING SYSTEMS WITH/WITHOUT THRESHOLD ARE SAME. FOR SYSTEM WITH THREHOLD ONLY FOLLOWING ITEMS ARE DIFFERENT: INITIAL AND SIDE COLUMN CAPS, INTERMEDIATE CAPS, LOWER BASE PROFILE AND BOTTOM WHEELS. THEIR APPLICATION IS THE SAME AS IN A SYSTEM WITHOUT THRESHOLD.

INSTALLATON STEPS ARE SAME FOR SLDNG SYSTEMS WTH THRESHOLD AND WTHOUT THRESHOLD.

8. SPECIFIC STAFF OF BKS SLIDING SYSTEM WITH THRESHOLD

W.6920BKS BOTTOM WHEELS OF SLIDE

SYS. WITH THRESHOLD

W.6903BKS BOTTOM BASE PROFILE OF

SLIDE SYS. WITH THRESHOLD

W.6900BKS BOTTOM FRAME PROFILE

OF SLIDE SYS. WITH THRESHOLD

W.6923BKS INTERMEDIATE CAP OF

SLIDE SYS. WITH THRESHOLD

W.6924BKS INITIAL AND SIDE COLUMN CAP


W.6925BKS BOTTOM SIDE COLUMN EQUIPMENT





GLASS

W.6826

W.6811

W.6812W.6813

W.6826

W.6903

W.6924

W.6923

B

DETAY BLEK 1 : 5

C

DETAY CLEK 1 : 5

25

8.1. NEEDED PARTS FOR INITIAL PANEL NEEDED PARTS OF MIDDLE AND INITIAL PANELS ARE SAME, EXCEPT AN INITIAL SEAL. INSTEAD

OF INITIAL SEAL AT THE MIDDLE PANEL H-SEAL IS USED.

W.6920BOTTOM WHEELS WITH THRESHOLD



W.6821W.6821

W.6920W.6920





FROM SYSTEM TOP.

W.6813INITIAL ALUMINUM

SEAL

ITS USED ON THE OUTER EDGES OF INITIAL PANELS

AS INSULATION.



INSULATION

W.6821UPPER WHEEL



THE SYSTEM.



W.6824MIDDLE AND INITIAL

CAPS

ITS INSTALLED ON THE LOWER BASE PROFILE

AT THE END OR MIDDLE POINTS.


CAPS


THE PANELS.

W.6903BOTTOM BASE

WITH THRESHOLD

ONLY ONE PIECE IS USED AT EACH GLASS PANEL FROM SYSTEM BOTTOM


GLASS

W.6826 W.6826

W.6811

W.6812 W.6812

W.6923

W.6903

W.6923

B

A

DETAY ALEK 1 : 4

DETAY BLEK 1 : 4

26

8.2. NEEDED PARTS FOR INTERMEDIATE PANEL

W.6903BOTTOM BASE

WITH THRESHOLD

ONLY ONE PIECE IS USED AT EACH GLASS PANEL FROM SYSTEM BOTTOM

W.6821 W.6821

W.6920W.6920





FROM SYSTEM TOP.



INSULATION

W.6821UPPER WHEEL



THE SYSTEM.




CAPS


THE PANELS.

W.6920BOTTOM WHEELS WITH THRESHOLD




INITIAL PANEL INTERMEDIATE

PANEL INTERMEDIATE PANEL

INTERMEDIATE PANEL INTERMEDIATE

PANEL

MIDDLE PANEL MIDDLE

PANELINITIAL PANEL

UPPER FRAME PROFILE

SIDE COLUMN PROFILE

SIDE COLUMN PROFILE

BOTTOM BASE PROFILE WITH

TRESHOLDH-SEAL

ALUMINUM GLASS SEAL

27

9. INSTALLATED BKS SLIDING SYSTEM WITH THRESHOLD

LOCK

LOCK

LOCK




TECHNICAL CATALOGUE OF BKS SLIDING SYSTEM …access-novello.com/userfiles/product_files_shared/BKS...

Documents

Transcript of TECHNICAL CATALOGUE OF BKS SLIDING SYSTEM …access-novello.com/userfiles/product_files_shared/BKS...