SSung 2008-Frontier Washer
Transcript of SSung 2008-Frontier Washer
WF8120SXW/XEGWF8150NXV/XST
2008. Frontier2-Global Training Manual
Digital Appliances Division
SAMSUNG Clothes Washer
INDEX
ContentsContents
Reinforcement of the premium line-up (Large Capacity / Ag+ / VRT)
To secure our leadership in the industry by introducing a new USP.
Product Features -1. Development Background
To respond to competitor’s large capacity wash-only model
Prior occupation of the market by constructing a full line-up including a large capacity model
[ for Germany ] [ for Thailand ]
Theme Function
Well-Being Wash → Reinforced Silver-Nano
(Sub-divided Course)
Indoor Installation System→ Zeus (Ball Balance) Adopted
→ Vibration/Noise Minimized
Wool Mark-Certified Washing→ Optimal Delicate Wash
→ Clothing Damage Minimized
Sub-Function
Perfect Rinse by Controlling the Number of Rinse Cycles
Design Points
Center Jog for User Convenience
Theme Model Concept & Image
Product Features – 2. Product Overview
Design Concept
Product Features – 3. Product Overview
•Change of the Assy-Drawer Badge
: Hauzen SAMSUNG
•Assy-Door
: White + STS Deco applied.
White appearance for Germany and dark silver for Thailand.
The SAMSUNG badge is applied to the Assy-Drawer.
White+STS Deco has been adopted for Germany as the Assy-Door, and Grey+STS Deco for Thailand
Product Features – 4. Differentiation
Sales Points
Super Capacity
- The largest capacity on the market so that a large amount or oversized laundry can be washed
at the same time.
VRTTM with DD Motor
- A stable and quiet wash with Samsung’s proprietary vibration and noise reduction technology,
anywhere, anytime.
Ag+ Technology
- Removes even invisible germs with the sterilization and antibiosis functions.
Diamond Drum with Wool Mark
- Texture deformation-free washing with the embossed drum surface.
- Keeps clothes looking new for a long time with the international-certified wool mark.
Laundry can be added as required. Convenient storing of frequently used
courses.
The wash progress can be seen at one glance with the Circle display / Polished,
luxurious design
Product Features – 5. Specifications
Product Image
X○○Diamond Drum
○○○Stop/Add
X○○Ball Balance
X○○Drum Steam (Intensive)
XX○Silver Wash
ThemeFeatures
690*790*970686*787*975Dimensions (W*D*H) (mm)
ø400mmø376mmInput Hole Size
AAB-AABVDE Performance Target
-2000WHeater Capacity
120010001000 (Performance B)Spin Speed
DDKDDWashing Motor
81ℓ96ℓDrum Capacity
Specifications
12kg / 10kg15kg12kgDesired Displayed Capacity (for Washing)
220/50230/50Standard Power
For ThailandFor GermanyModel
Competitor’s Model (WP)F2MC-GLOBALItem
NA
Product Features – 5. Specifications (1)
NA
Product Features – 5. Specifications (1)
1WF8120SXW,XEG,ENG+DUT,GERMANY,W180,L255,DC68-02626CMANUAL-BOOK
1B1415J(NO-SPONGE),EPDM+PP,-,L1920DC97-02250FASSY HOSE
DRAIN
2PP,T1.5,-,-,WHT,MACH-PJT/BJ750 RESINDC61-10688B
2SWF-P12,PP(TB53),-,-,-,WHT,-,DC61-10688A
CAP-FIXER
1P1405J,PVC+NYLON,-,-,-,L1500,GRY,ACQUA-STOPDC62-00079AHOSE-WATER
P1405J,PVC+NYLON,-,-,-,L1500,GRY,ACQUA-STOP
CR,T2.5,OD36
SPEC
1DC62-10278AHOSE-HANGER
1DC60-40146ABOLT-SPANER
QTYCodeItem
Product Features – 6. Specifications
787Depth
686Width
975Height
mmDimension
94Kg(Main Body),101Kg(Package)Product Weight
686X787X975 (WidthXDepthXHeight)Dimensions(mm)
0.05~0.78Mpa(0.5~8Kgf/Cm2)Water Pressure
Centrifugal Dehydration TypeSpin Type
Drum TypeWashing Type
220V/50HzPower
Drum WasherType
Product Features – 7. Specifications (1)
�
�
�
� � � � �
�
�
� �
Pressing this button changes the wash type in the following order: Main →Main + Prewash → Main + Soak → Main + E-Save → Main (on the basis of the Cotton
Course).
Pressing this button changes the water temperature in the following order: 40°C→60°C→ Cold Water→40°C (on the basis of the Cotton Course).*Do not supply only hot water.
Press this button to make a reservation. You can set the delay time up to 24 hours in one hour units.
Product Features – 7. Specifications (2)
Press this button for additional rinse cycles or to perform rinse cycles only.
Press this button to select a spin level or to perform spin cycles only.* : Do Not Spin skips the spin cycle after draining.
Press this button to start or pause washing or to change the Wash Course.
To turn the washer off, make sure to stop the operation by pressing the Start/Pause button before
pressing the power button.
�
�
�
� � � � �
�
�
� �
Product Features – 7. Specifications (3)
Select this option to have more intensive washing for heavily soiled items.This option is to enhance washing performance by improving the temperature and soak effect
If this button is selected, silver ion water is supplied for the wash and last rinse operation to sterilize the
washing and add an anti-bacterial coating.
If this button is selected, washing machine saves a configured course or load saved course.
�
�
�
� � � � �
�
�
� �
Product Features – 7. Specifications (4)
Press this button to start or pause washing or to change the Wash Course.
Turn the course dial to select a course. Use it to remove odors.
This is activated or deactivated by pressing both the [Temp] and [Rinse] buttons at the same time and
holding them for 3 seconds.
Use this function to prevent children from accidently operating the washer.
�
�
�
� � � � �
�
�
� �
Circuits – Main PBA Major Part Layout and Terminal Functions
Adobe Acrobat 7.0 Document
Circuits – Main PBA Major Part Layout and Terminal Functions
Circuits – Detailed Descriptions for the Main PBA Connector and Terminal Part
Circuit - Circuit Diagram
Adobe Acrobat 7.0 Document
Circuits – Circuit Description – Entire System Diagram
Adobe Acrobat 7.0 Document
Circuits – Sub PBA Major Part Layout and Terminal Functions
Adobe Acrobat 7.0 Document
Circuits – Detailed Descriptions for the SUB PBA Connector and Terminal Part
Reference – 5. Test Procedure (1)
Entering Test Mode
� To enter the Test Mode [Power off mode only]
1. Press the [Temperatur] and [Proqrammende] keys at the same time.
2. Press the [Ein/Aus] button while holding down the 2 keys.
3. You will enter the Test mode.
Test mode
* Before checking:(It works only when there is water.)1. Switch on the machine and supply the water on the standard mode.2. Before entering the Test mode, switch off the machine.- CheckpointConnection with the motor (Blue, White, and Red colors in order.)The coil resistance between Blue-Red, Red-White, White-Blue (10~20Ω)�It works only when there is water.�
1. Enter the Test mode.2. Turn the Course Jog dial until the [Handtucher]
course is lit.3. “�ES�” is displayed in Segment.4. If you press the [Start/Pause] button, the motor
starts or stops.
Check if the Motor works properly.
1
Checkpoint for TroublesTest ProcedureCheckpoin
tNo
� �
Reference – 5. Test Procedure (2)
Test mode
Check the voltage of Water Supply Valve connector.(2�0V or 110V)�You should lock the door by pressing the Temp button before checking the valve.�
1. Enter the Test mode.2. Press the [Optionen] button.3. Whenever you press the button, check the operation
of Water Supply Valve for each function.- Extra valve(Cold) / Drying valve(30°C)
Cold water valve(40°C) / Hot water valve(60°C) Steam valve(95°C)
Check Water Supply Valve Operation
3
* Before checking:(It works only when there is water.)1. Switch on the machine and supply the water on the standard mode.2. Before entering the Test mode, switch off the machine.- CheckpointMotor side 3P connector:Voltage between Orange-Pink (5V)Voltage between Orange-White (5V↔0V)Voltage between Orange-Black (5V↔0V)
1. Enter the Test mode.2. Turn the Course Jog dial until the [Handtucher]
course is lit.3. “�ES�” is displayed in Segment.4. If you press the [Start/Pause] button, the motor
starts or stops.
Check RotationSensor
2
Checkpoint for TroublesTest ProcedureCheckpoin
tNo
Test mode
Voltage between terminals when the heater works (220V)Resistance between the heater terminals (27±10%Ω)
1. Enter the Test mode. 2. Whenever you press the [Proqrammende] button,
the heater operates in the following modes in order:Dry(Skip) → Water → Steam(Skip) → Off
� For each operation, the heater works for 5 seconds.
Check Heater
operation6
Voltage between terminals of the door open and close S/W drive part (Solenoid) (220V)Resistance between the door S/W terminals (143Ω±10%)
1. Enter the Test mode.
2. [Temperatur] � ���� ����3. [Proqrammende] � ���� ������
Check Door Open
Switch 5
Voltage of Drain Motor connector (220V or 110V)
1. Enter the Test mode.
2. [Spulen] � Drain motor is turned on or turned off.
Check Drain Motor
Operation
4
Checkpoint for TroublesTest ProcedureCheckpoin
tNo
Reference – 5. Test Procedure (3)
Reference – 5. Test Procedure (4)
Test mode
- Replace the Sub PCB.- If the voltage between the
Black and White of the Main PCB is not equal to 220V, replace the Noise Filter.
1. There is a switch or LED that does not work.2. Unable to turn the power on.
Check Main PCB
9
The resistance of the Thermistor is approximately 12kΩ. The voltage between the ends of the cable is 5V.
1. Enter the Test mode. 2. Turn the Course Dial until the.
[Stark verschmutzt]: Current Water Temperature
[Mischwasche]: Dry Duct Temperature
[Pflegeleicht]:Condensed Water Temperature
Check if the
Thermistor works
properly.
8
Water Level Sensor’s Pink-Orange (5V), Violet-Orange (Frequency: 22.7 ~ 25 kHz)
1. Enter the Test mode. 2. Turn the Course Dial until the�Baumwolle]lamp is lit.
3. Water Level Frequency isdisplayed in the display window.
Check if the Water
Level Sensor works
properly.
7
Checkpoint for TroublesTest ProcedureCheckpoin
tNo
Circuits – 5. Error Mode (1)
4E2
4E1
4E
Error3
3EMotor Hall Sensor Error
2
1EError1
NO
Circuits – 5. Error Mode (2)
5EError4
NO
- When the T is defective or is not installed properly.
55 in a particular cReset
55
(Reason: The hot drained water may burn human body.)-When the cold and hot water supply hoses are interchanged.CECooling Error7
- When a screw is fastened excessively during the Sub-Assembly process.
- When the injected material inside is deformed.
- When a button other than the Switch is pressed (for equal to or longer than 30 seconds).
bE2Switch
(Main Relay )6
- Separate the Sub PBA from the Control Panel and find any soldering defects.
- Check the terminals of the connector connecting the Sub PBA and the Main PBA Check if there is a missing part or an incomplete installation.
- When the signal between the Sub PBA and the Main PBAerror.
AE5
Circuits – 5. Error Mode (3)
If the monitoring is unstable, replace the HE2
HE1
S is defective. (Incomplete Connection or Defective T ) - When the Washing Heater Overheating Protection Temperature Sensor, which is installed at the bottom is frozen, and the Water Level Sensor operates when there is no water and it detects 100 ~ 150 , the power is turned off.
HE
Heater Error10
In this case, replace the drive condenser unconditionally because it cannot be measured with a tester.
- When the fan does not work because the cooling fan is bound or the bearing is rusted.
- When no power is supplied to the Fan Motor .- When the belt is out of place.
- When the drive condenser terminal is disconnected when the Top Cover is inserted.
FEFan 9
Switch turns on and off repeatedly.(If the error has occurred due to this reason, reproducing the error is
difficult.)dE2
- When the Main PCB is defective.
- This may occur intermittently due to an electrical leakage of the wire.
- The Door Lock switch is not connected or the
dE1
- When the door is pushed against due to the high pressure inside the washer when the
- When the door is pulled by force.
- When the switch contact is broken due to a deformation of the Door Hook.
dE
Door Error8
NO
Circuit – 5. Error Mode (4)
- When the is degraded.
- When water is continuously supplied when there is an in the W or it is frozen.
-When the w and is blocked (the part becomes narrower.)
- When water is supplied continuously because the w
OE, OFOverflow 12
- When the screws fixing the Rear and the Front Tub are not fastened.
- When the Nozzle-diaphragm is assembled in the wrong direction or the rubber packing is not installed.
- When the Duct Condensing Fixing Screw is worn.
- When water leaks from the .
- When the filter cover is not assembled.
- When the D connection is not connected.
- When water leaks from the front because of bubbles caused by anexcessive amount of
- When the Bolt Fixing Part of the Rear Tub is damaged.
- When the washer spins when the Air is out of position.
- When the (out of position).
LEError11
NO
Circuit – 5. Error Mode (5)
- Find the reason for the unbalance and explain the usage precautions to the customer.
UEUnbalance Error14
- When the c is not or incompletely connected.
- When the Duct Condensing Temperature is open-circuited or short-circuited.
T S
(Models earlier than )
- When the Duct Condensing T is open-circuited.
tE3
- When the c is not or incompletely connected.
A Duct Condensing T S Defect (Models earlier than
)
- When the Duct Ass‘y Fan Housing T S(a defect such as an internal short-circuit and wire breakage)
tE2
- When the Washing Heater Overheating Protection Temperature Sensor, which is installed at the bottom is frozen, and the Water Level Sensor operates when there is no water and it detects 100 ~ 150 , the power is turned off.
- When the c is not or incompletely connected.S Defect:
because a wire breakage, disconnection, or short circuit occurs.
- S is defective. (Incomplete Connection or Defective T )
tE1
Error13
NO
Troubleshooting (1)
Troubleshooting (2)
Troubleshooting (3)
Troubleshooting (4)
Troubleshooting (5)
Troubleshooting (6)
Troubleshooting (7)
Troubleshooting (8)
Disassembly and Reassembly – Accessories
Disassembly and Reassembly – 1. Motor
Disassembly and Reassembly – 2. Heater
Disassembly and Reassembly – 3. Main PCB
’
Disassembly and Reassembly–4. Top-Cover/Con-Panel
Disassembly and Reassembly – 5. Door
Disassembly and Reassembly – 6. Door Lock-S/W
•
Disassembly and Reassembly – 7. Water-Valve, Level-Sensor
•
Disassembly and Reassembly – 8. Duct-Part
•
Disassembly and Reassembly – 8. Duct-Part
Disassembly and Reassembly – 9. Detergent-Drawer
Disassembly and Reassembly – 10. Pump-Motor
Disassembly and Reassembly – 11. Tub
Disassembly and Reassembly – 11. Tub
Reference – 1. Silver Nano Kit
1. Turn the product off.
2. Press the [Silver Wash] and the [Power] buttons simultaneously.
3. The number of performed Silver Nano courses is displayed in the display window as
follows.
• Users can use the Silver Nano course 1550 times. If the Silver Nano course is
performed three times a week, the Silver Nano kit can be used for 10 years.
• Even if the lifetime of the Silver Nano kit nears its end, the washing machine will
continue to work properly except for the Silver Nano function. (This is not a product
defect and the Silver Nano kit can be replaced for a fee on request.)
Checking the Silver
Nano kit replacement
time.
• This function enables users to identify when to replace the Silver Nano kit by
remembering and saving the number of Silver Nano courses that have been
performed.
What is the Silver Nano
kit replacement time
check function?
DescriptionItem
Reference – 1. Silver Nano Kit
► Replacing the Silver Nano kit.
• For the disassembly and reassembly procedures for the Silver Nano kit, refer to
the descriptions in the “3. Disassemble and Assembly” chapter.
► Initializing the product after replacing the Silver Nano kit.
1. Press the [Silver Wash] and the [Power] buttons simultaneously.
2. Press the [Delay End] button.
3. If the initialization is successful, the number of performed Silver Nano courses is
reset to “0”.
What is the Silver Nano
kit replacement time
check function?
DescriptionItem
[ Ball Balancer ]Automatically counterbalances unbalanced laundry that occurs while spinning.
Vibrations while spinning are caused by unbalanced laundry. The balls in the balancer
automatically move to the other side to counterbalance the unbalanced weight to offset the
cause of the vibration.
Ultra Low Vibration (Ball Balance) Technology
Auto Balancing
Counterbalance
Ball Balance Previous Balance
Reference – 2. VRT