Specification sheetProject:

Area:Generic Underwater System (GLOBIC AF) for STEEL and FIBREGLASS

Underwater Area for STEEL and FIBERGLASS

Hempel (Australia) Pty. Ltd.

Surface preparation:FIBERGLASSOil and grease etc. to be removed by emulsion cleaning. Entire area to be (high pressure)fresh water cleaned in order to remove salts and other contaminants. When the surface isdry: Careful abrasive blasting, or sand with 60-80 grit paper.Dust off residues.

STEELOil and grease etc. to be removed by emulsion cleaning. Entire area to be (high pressure)fresh water cleaned in order to remove salts and other contaminants. When the surface isdry: Abrasive blasting to minimum Sa 2½ according to ISO 8501-1:2007 with a surfaceprofile corresponding to Rugotest No. 3 BN 11.For minor areas, grind with 36-60 grit resin discs.Dust off residues.

Product name (including quality number)Treated area

% ColourShade no.

Film thickness(micron)

Wet Dry (sqm/ltr) BrushRoller

SprayNozzleorifice

RecommendedNozzle

pressure

Application methodsTheoretical spreadingrate

HEMPADUR QUATTRO 17634 100 Red 50630 175 125 .021"-.025" 250 bar5.8 (X) (X) Xf/cHEMPADUR QUATTRO 17634 100 Beige 22090 175 125 .021"-.025" 250 bar5.8 (X) (X) Xf/cHEMPADUR 45182 100 Yellowish grey 25150 175 75 .023" 200 bar6.1 (X) Xf/cHEMPEL'S ANTIFOULING GLOBIC 81900 100 Black 19990 200 100 .027"-.031" 270 bar5.4 (X) (X) Xf/cHEMPEL'S ANTIFOULING GLOBIC 81900 100 Black 19990 200 100 .027"-.031" 270 bar5.4 (X) (X) Xf/c

t/u: touch up f/c: full coat s/c: stripe coat Total d.f.t. 525 X: Recommended (X): Possible

Recoating intervals. Ample ventilation Hrs=Hour(s) Mth=Month(s) N/R=Not Recommended

Quality no

D.F.T.

(micron)Recoated with

quality no40°C 30°C 20°C 10°C 0°C -10°C

Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max.2 Hrs 15 Day 3 Hrs 22½ Day 4 Hrs 30 Day 8 Hrs 60 Day 18 Hrs 90 Day 36 Hrs 90 Day1763417634 1252 Hrs 15 Day 3 Hrs 22½ Day 4 Hrs 30 Day 8 Hrs 60 Day 18 Hrs 90 Day 36 Hrs 90 Day4518217634 1252 Hrs 60 Hrs 3 Hrs 3½ Day 4 Hrs 5 Day 8 Hrs 10 Day 19 Hrs 22½ Day 38 Hrs 45 Day8190045182 754 Hrs None 6 Hrs None 8 Hrs None 15 Hrs None 30 Hrs None 60 Hrs None8190081900 1005 Hrs None 7 Hrs None 10 Hrs None 19 Hrs None 39 Hrs None 3 Day NoneDrying time before taking into use, before

un-docking

Hempel's PreSale System 2.6.17 (Build 890)Printed at: Environment :

1Page:19.01.2015 14:14

User name:Department name:

Created/Last modified: 19.01.2015 14:09

Quality Code:David NeumannBrisbane office Immersion

AUDNE1335L

Remarks and Product information see next page.

Specification sheetProject:

Area:Generic Underwater System (GLOBIC AF) for STEEL and FIBREGLASS

Underwater Area for STEEL and FIBERGLASS

Hempel (Australia) Pty. Ltd.

Product information:Shade no.

Volumesolids %

Curingagent

Mixing ratiovolume

Pot life Dry to touch Application restrictionsThinner

Flashpoint Min. Temp. Max. RH%

20°C 20°C °C °CHEMPADUR QUATTRO 17634 50630 72 97334 4 : 1 2 h 4 h 27 08450 -10 HEMPADUR QUATTRO 17634 22090 72 97334 4 : 1 2 h 4 h 27 08450 -10 HEMPADUR 45182 25150 46 98180 4 : 1 3 h 6 h 23 08450 -10 HEMPEL'S ANTIFOULING GLOBIC 81900 19990 54 4 h 23 08080HEMPEL'S ANTIFOULING GLOBIC 81900 19990 54 4 h 23 08080

Remarks:Normal good painting practice must be followed throughout the entire painting procedure.The specified high film thickness can best be obtained by airless spray application. If another application method is used more applications may be necessary to achieve the specifieddry film thickness.HEMPADUR QUATTRO 17634A two pack high performance epoxy priming and undercoating system.This product has outstanding corrosion, impact, and water resistance qualities both above and below the waterline.Quick to recoat.HEMPADUR 45182A two pack underwater primer with excellent waterproofing properties.45182 opens up the recoat schedule to a more user friendly timing; unlike the tight timelines of traditional single pack to two pack systems.Used as a tiecoat before antifouling.GLOBIC 81900A self-polishing antifoul using HEMPEL'S patented Inorganic Fibre Reinforcement Technology to enhance the self-polishing characteristics,and therfore better control of the release of the biocide package.Two different polishing levels are available: 86901 for Low Activity vessels, and 86951 for High Activity vessels.Available in Red 51110, Brown 60700 (turns grey when immersed), Black 19990 and Dark Blue 30170.

Hempel's PreSale System 2.6.17 (Build 890)Printed at: Environment :

2Page:19.01.2015 14:14

User name:Department name:

Created/Last modified: 19.01.2015 14:09

Quality Code:David NeumannBrisbane office Immersion

AUDNE1335L

The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to thebest of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do notguarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions regarding Hempel’s liability in its applicable conditions for sale, delivery and service shall apply to any andall claims arising out of or in connection with the use of the products recommended above, overleaf or otherwise.

Product Data

Description:

Recommended use:

Service temperature:

Certificates/Approvals:

Availability:

HEMPADUR QUATTRO 17634 is a two-component universal epoxy paint, which cures to a hard and tough coating with good resistance to abrasion, seawater and various oils.

As a universal epoxy and self-primed high performance coating system for atmospheric or in-water service, including water ballast tanks and cargo oil tanks to be coated according to IMO-PSPCrequirements (Resolutions MSC.215(82) and MSC.288(87)). HEMPADUR QUATTRO 17634 is intended for all year application down to -10°C/15°F and for in-shop applications where fast recoatingand handling is required.

Maximum, dry exposure only: 120°C/248°FBallast water service. Resists normal ambient temperatures at sea (Avoid long-term exposure to negative temperature gradients).Other liquids: Contact HEMPEL

Part of Group Assortment. Local availability subject to confirmation.

HEMPADUR QUATTRO 1763417634: BASE 17636: CURING AGENT 97334

PSPC type approved. (Consult HEMPEL for specific Type Approval Certificates)Complies with Section 175.300 of the Code of Federal Regulations Title 21 – Dry Foodstuff. Consult Hempel for details.Tested for non-contamination of grain cargo at the Newcastle Occupational Health & Hygiene, Great Britain.Approved as a low flame spread material when used as part of a predefined paint system. Please refer to “Declaration of Conformity” on www.Hempel.com for further details.

Excellent anticorrosive and very good mechanical properties.Short drying time.Curing down to -10°C/14°F.

Features:

Product Data

PHYSICAL CONSTANTS:

The physical constants stated are nominal data according to the HEMPEL Group's approved formulas.

Shade nos/Colours:Finish:Volume solids, %:Theoretical spreading rate:

VOC content:

Fully cured:

Dry to touch:Specific gravity:Flash point:

-

50630*/ RedSemi-flat72 ± 15.8 m2/l [232.6 sq.ft./US gallon] to 125 micron/5 mils

4 approx. hour(s) 20°C/68°F 9 (approx.) hour(s) 5°C/41°F7 day(s) 20°C/68°F20 day(s) 5°C/41°F

- *other shades according to assortment list.

27 °C [80.6 °F]1.4 kg/litre [11.6 lbs/US gallon]

277 g/l [2.3 lbs/US gallon]

APPLICATION DETAILS:

Version, mixed product:Mixing ratio:

Application method:Thinner (max.vol.):

17634

4:1 by volumeAirless spray / Brush / Roller08450 (5%) / 08450 (5%) / 08450 (5%)

Nozzle orifice: 0.021 to 0.025 "Nozzle pressure: 250 bar [3625 psi]

(Airless spray data are indicative and subject to adjustment)

Indicated film thickness, dry: 125 micron [5 mils]Indicated film thickness, wet: 175 micron [7 mils]Overcoat interval, min: see REMARKS overleafOvercoat interval, max: see REMARKS overleaf

BASE 17636: CURING AGENT 97334

2 hour(s) 20°C/68°FPot life (Airless spray):2 hour(s) 20°C/68°FPot life (Brush):

Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers,consult HEMPEL Safety Data Sheets and follow all local or national safety regulations.

HEMPEL'S TOOL CLEANER 99610Cleaning of tools:

- see REMARKS overleafInduction time:

Not available.

Page: 1/3

-Product Data SheetDate of issue: September 2014

HEMPADUR QUATTRO 17634

SURFACE PREPARATION: New steel: Remove oil and grease etc. thoroughly with suitable detergent. Remove salts and other contaminants by high pressure fresh water cleaning. Abrasive blasting to minimum Sa 2½ (ISO 8501-1:2007) with a surface profile corresponding to Rugotest No. 3, N9a to N10, preferably BN9a to BN10,Keane-Tator Comparator, 2.0 G/S or ISO Comparator, Medium (G). Apply immediately after cleaning.All damage of shopprimer and contamination from storage and fabrication should be thoroughly cleaned prior to overcoating. For repair and touch-up use: HEMPADUR QUATTRO 17634.Ballast tanks and cargo oil tanks: See separate APPLICATION INSTRUCTIONSSteel, maintenance: Remove oil and grease, etc. with suitable detergent. Remove salt and other contaminants by (high pressure) fresh water cleaning. Clean damaged areas thoroughly by power tool cleaning to St 3 (minor areas) or by abrasive blasting to min. Sa 2, preferably to Sa 2½. Improved surface preparation will improve the performance of the paint. As an alternative to dry cleaning, water jetting to sound, well adhering coat and/or to steel. Intact coat must appear with roughened surface after the water jetting. By water jetting to steel, cleanliness shall be Wa 2 - WA 2½ (atmospheric exposure) / minimum Wa 2½ (immersion) (ISO 8501-4:2006). A flash-rust degree of maximum M (atmospheric exposure) / M, preferably L (immersion) (ISO 8501-4:2006) is acceptable before application. Feather edges to sound and intact paint. Dust off residues. Touch up to full film thickness.On pit-corroded surfaces, excessive amounts of salt residues may call for water jetting or wet abrasive blasting, alternatively dry abrasive blasting followed by high pressure fresh water hosing, drying, and finally, dry abrasive blasting again.Other substrates: contact Hempel.

APPLICATION CONDITIONS: Use only where application and curing can proceed at temperatures above: -10°C/14°F. The temperature of the paint itself should be above: 15°C/59°F. Apply only on a dry and clean surface with a temperature above the dew point to avoid condensation. In confined spaces provide adequate ventilation during application and drying.

PRECEDING COAT:

SUBSEQUENT COAT:

None, or as per specification. When diluted to 25-30%, the product can be used as blast primer preceding a full coat application of the product.

According to specification.

REMARKS:

Weathering/service temperatures: The natural tendency of epoxy coatings to chalk in outdoor exposure and to become more sensitive to mechanical damage and chemical exposure at elevated temperatures is also reflected in this product.Has a tendency to yellow after application. This has no influence on the performance nor does the yellowing affect any topcoat applied.

Film thicknesses/thinning:

Shades:

In case two-component spray-equipment is used consult separate APPLICATION INSTRUCTIONS.May be specified in another film thickness than indicated depending on purpose and area of use. This will alter spreading rate and may influence drying time and overcoating interval. Normal range dry is:100-200 micron/4-8 mils. For ballast tanks and cargo oil tanks at newbuilding stage minimum specified dft is: 2 x 160 micron. (Consult the separate APPLICATION INSTRUCTIONS)Among the standard shades in the assortment, there are shades available containing aluminium; such as shade nos. 23420, 15740 and 57530.

HEMPADUR QUATTRO 17634 For professional use only.Note:

Overcoating: Overcoating intervals related to later conditions of exposure: If the maximum overcoating interval is exceeded, roughening of the surface is necessary to ensure intercoat adhesion.Before overcoating after exposure in contaminated environment, clean the surface thoroughly with high pressure fresh water hosing and allow drying.

A specification supersedes any guideline overcoat intervals indicated in the table.

Induction time: To facilitate proper application properties it is recommended to allow the thoroughly mixed BASE and CURING AGENT to prereact before application at temperatures below: 15°C/59°F.Pot life of mixed paint:3 hours - 15°C/59°F, 2 hours - 20°C/68°F, 1.5 hour - 25°C/77°F, 1 hour - 30°C/86°FThe viscosity can be too high for airless spray application below: 15°C/59°F. Temperatures above 30°C/86°F should preferably be avoided.

Environment Immersion

HEMPATEX 18 h 72 h 9 h 36 h 2 h 8 h

HEMPADUR 36 h 90 d 90 d18 h 30 d4 h

Environment

Min Max Min Max Min Max

HEMPATHANE 18 h 90 d 9 h 90 d 2 h 20 d

Atmospheric, medium

HEMPADUR 18 h 90 d 90 d9 h 30 d2 h

-10°C (14°F) 0°C (32°F) 20°C (68°F)

NR = Not Recommended, Ext. = Extended, m = minute(s), h = hour(s), d = day(s)

Surface temperature:

Page: 2/3

-Product Data SheetDate of issue: September 2014

HEMPADUR QUATTRO 17634

This Product Data Sheet supersedes those previously issued.For explanations, definitions and scope, see “Explanatory Notes” available on www.hempel.com. Data, specifications, directions and recommendations given in this data sheet represent only test results or experience obtained under controlled or specially defined circumstances. Their accuracy,completeness or appropriateness under the actual conditions of any intended use of the Products herein must be determined exclusively by the Buyer and/or User.The Products are supplied and all technical assistance is given subject to HEMPEL's GENERAL CONDITIONS OF SALES, DELIVERY AND SERVICE, unless otherwise expressly agreed in writing. The Manufacturer and Seller disclaim, and Buyer and/or User waive all claims involving, any liability, including but not limited to negligence, except as expressed in said GENERAL CONDITIONS for all results, injury or direct or consequential losses or damages arising from the use of the Products as recommended above, on the overleaf or otherwise. Product data are subject to change without notice and become void five years from the date of issue.

X Move PDS Disclaimer to Second page

ISSUED BY: HEMPEL A/S1763450630

Page: 3/3

-Product Data SheetDate of issue: September 2014

Product Data

Description:

Recommended use:

Service temperature:

Availability:

HEMPADUR 45182 is a two-component, low-temperature curing, modified polyamide adduct cured epoxy.

For marine and protective use as a "tiecoat" (“tackcoat”) between epoxy and physically drying coatings.For marine use also as a “sealer” of old antifouling.

Maximum, dry exposure only: 80°C/176°F

Part of Group Assortment. Local availability subject to confirmation.

HEMPADUR 4518245182: BASE 45187 : CURING AGENT 98180

Product Data

PHYSICAL CONSTANTS:

The physical constants stated are nominal data according to the HEMPEL Group's approved formulas.

Shade nos/Colours:Finish:Volume solids, %:Theoretical spreading rate:

VOC content:Fully cured:Dry to touch:Specific gravity:Flash point:

-

25150 / Yellowish greyFlat46 ± 14.6 m2/l [184.5 sq.ft./US gallon] - 100 micron/4 mils

6 approx. hour(s) 20°C/68°F7 day(s) 20°C/68°F

23 °C [73.4 °F]1.3 kg/litre [11.1 lbs/US gallon]

483 g/l [4 lbs/US gallon]

APPLICATION DETAILS:

Version, mixed product:Mixing ratio:

Application method:Thinner (max.vol.):

45182

4 : 1 by volumeAirless spray / Brush08450 (5%) / 08450 (5%)

Pot life:Nozzle orifice:

3 hour(s) 20°C/68°F0.023 "

Nozzle pressure: 200 bar [2900 psi](Airless spray data are indicative and subject to adjustment)

Indicated film thickness, dry: 100 micron [4 mils]Indicated film thickness, wet: 225 micron [9 mils]Overcoat interval, min: see REMARKS overleafOvercoat interval, max: see REMARKS overleaf

BASE 45187 : CURING AGENT 98180

Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers,consult HEMPEL Safety Data Sheets and follow all local or national safety regulations.

HEMPEL'S TOOL CLEANER 99610Cleaning of tools:

-----------

Page: 1/2

-Product Data SheetDate of issue: October 2013

HEMPADUR 45182

SURFACE PREPARATION: New steel: Remove oil and grease etc. thoroughly with suitable detergent. Remove salts and other contaminants by high pressure fresh water cleaning. Abrasive blasting to minimum Sa 2½ (ISO 8501-1:2007) with a surface profile corresponding to Rugotest No. 3, N9a to N10, preferably BN9a to BN10,Keane-Tator Comparator, 2.0 G/S or ISO Comparator, Medium (G). For temporary protection, if required, use a suitable shopprimer. All damage of shopprimer and contamination from storage and fabrication should be thoroughly cleaned prior to final painting.Repair and maintenance: Remove oil and grease etc. thoroughly with suitable detergent. Remove salts and other contaminants by high pressure fresh water cleaning. When used as "tiecoat": Remove all rust and loose material by abrasive blasting or power tool cleaning. Dust off residues. Touch up bare spots to full film thickness.When used as “sealer” on old antifouling: a very careful high pressure freshwater cleaning -or jetting, if needed - to remove possible leached layer of antifouling and make sure that old layers of weak intercoat adhesion (“sandwich structure”) really are removed.

APPLICATION CONDITIONS: Apply only on a dry and clean surface with a temperature above the dew point to avoid condensation.Use only where application and curing can proceed at temperatures above: -10°C/14°F. The temperature of the surface and that of the paint itself must also be above this limit.In confined spaces provide adequate ventilation during application and drying.

PRECEDING COAT:

SUBSEQUENT COAT:

According to specification. In case of an old antifouling system this must be well cleaned and in good condition.

According to specification.

REMARKS:

Film thicknesses/thinning: The product is designed for overcoating with antifoulings in any normal specified total film thicknesses.The product is not designed for overcoating with heavy duty epoxy systems. Later maintenance of paint systems with the product as a part of the system is accordingly most conveniently carried out by touch-up with a “mastic” type epoxy and with a proper overlap of intact surrounding paint system. May be specified in another film thickness than indicated depending on purpose and area of use. This will alter spreading rate and may influence drying time and recoating interval. Normal range dry is: 75-125 micron/3-5 mils. As "sealer" typically to be specified in: 50-75 micron/2-3 mils dry film thickness.Thinning may be required to facilitate proper film formation.

HEMPADUR 45182 For professional use only.Note:

Overcoating: Overcoating intervals related to later conditions of exposure: If the maximum overcoating interval is exceeded, roughening of the surface is necessary to ensure intercoat adhesion.Before overcoating after exposure in contaminated environment, clean the surface thoroughly with high pressure fresh water hosing and allow drying.

A specification supersedes any guideline overcoat intervals indicated in the table.

This Product Data Sheet supersedes those previously issued.For explanations, definitions and scope, see “Explanatory Notes” available on www.hempel.com. Data, specifications, directions and recommendations given in this data sheet represent only test results or experience obtained under controlled or specially defined circumstances. Their accuracy,completeness or appropriateness under the actual conditions of any intended use of the Products herein must be determined exclusively by the Buyer and/or User.The Products are supplied and all technical assistance is given subject to HEMPEL's GENERAL CONDITIONS OF SALES, DELIVERY AND SERVICE, unless otherwise expressly agreed in writing. The Manufacturer and Seller disclaim, and Buyer and/or User waive all claims involving, any liability, including but not limited to negligence, except as expressed in said GENERAL CONDITIONS for all results, injury or direct or consequential losses or damages arising from the use of the Products as recommended above, on the overleaf or otherwise. Product data are subject to change without notice and become void five years from the date of issue.

X Move PDS Disclaimer to Second page

Overcoating note: A completely clean surface is mandatory to ensure intercoat adhesion, especially at long overcoating intervals. Any dirt, oil, grease, and other foreign matter must be removed with suitable detergent followed by (high pressure) fresh water cleaning. Salts to be removed by fresh water hosing. Any degraded surface layer, as a result of a long exposure period, must be removed as well. Water jetting may be relevant to remove any degraded surface layer and may also replace the above mentioned cleaning methods when properly executed. To check whether the quality of the surface cleaning is adequate, a test patch may be relevant. A thin extra coat of the product may advantageously be applied if there is any doubt about suitability of cleaning process.

ISSUED BY: HEMPEL A/S4518225150

Environment

Min Max Min Max Min Max

Immersion

Conventional A/F 54 h 45 d 22½ d27 h 5 d6 h

-10°C (14°F) 0°C (32°F) 20°C (68°F)

NR = Not Recomended, Ext. = Extended, m = minute(s), h = hour(s), d = day(s)

Surface temperature:

Page: 2/2

-Product Data SheetDate of issue: October 2013

Product Data

Description:

Recommended use:

Certificates/Approvals:

Availability:

HEMPEL’S ANTIFOULING GLOBIC 81900 is a high solid, tin-free, self-smoothening and self-polishing antifouling. Polishing takes place based on an ion exchange resulting in a hydrolysable activated layer.An inorganic fibre reinforcement of the resin matrix ensures effective polishing control and mechanical strength. A powerful bioactive mixture and its self-renewing effect makes it suitable for protection in the severe fouling conditions of coastal waters. The system provides a certain control of roughness.This product does not contain organotin compounds acting as biocides and complies with the International Convention on the Control of Harmful Antifouling Systems on Ships as adopted by IMO October 2001 (IMO document AFS/CONF/26).

As a selfpolishing antifouling for newbuildings and maintenance of bottom and boottop on vessels operating at low to medium speed and activity with short to medium idle periods. For drydocking intervals of up to 60 months.Aluminium hulls: see REMARKS overleaf.

Not included in Group Assortment. Availability subject to special agreement.

HEMPEL'S ANTIFOULING GLOBIC 81900

TIN-FREEFeatures:

Product Data

PHYSICAL CONSTANTS:

The physical constants stated are nominal data according to the HEMPEL Group's approved formulas.

Shade nos/Colours:Finish: FlatVolume solids, %: 58 ± 1Theoretical spreading rate: 5.8 m2/l [232.6 sq.ft./US gallon] - 100 micron/4 mils

VOC content:Dry to touch: 4 to 5 hour(s) 20°C/68°FSpecific gravity:Flash point:

-

51110* / Red

- *other shades according to assortment list.

23 °C [73.4 °F]2 kg/litre [16.5 lbs/US gallon]

376 g/l [3.1 lbs/US gallon]

APPLICATION DETAILS:

Application method: Airless spray see REMARKS overleafThinner (max.vol.): 08080 (5%)Nozzle orifice: 0.027 to 0.031 "Nozzle pressure: 270 bar [3915 psi]

(Airless spray data are indicative and subject to adjustment)

Indicated film thickness, dry: 100 micron [4 mils] see REMARKS overleafIndicated film thickness, wet: 175 micron [7 mils]Overcoat interval, min: According to specification.Overcoat interval, max: According to specification.

Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers,consult HEMPEL Safety Data Sheets and follow all local or national safety regulations.

HEMPEL'S THINNER 08080Cleaning of tools:

Page: 1/2

-Product Data SheetDate of issue: September 2014

SURFACE PREPARATION: According to specification.Existing old self-polishing or ablative antifouling: Remove possible oil and grease etc. with suitable detergent, followed by high pressure fresh water cleaning for a thorough removal of any possible weak structure of leached antifouling.Sealer: Whether to use a sealer coat/tiecoat or not depends on the type and condition of the existing antifouling.

APPLICATION CONDITIONS: Apply only on a dry and clean surface with a temperature above the dew point to avoid condensation.In confined spaces provide adequate ventilation during application and drying.

PRECEDING COAT:

SUBSEQUENT COAT:

According to specification. Recommended systems are: HEMPATEX HI-BUILD 46330, HEMPADUR 45182

None, or as per specification.

REMARKS: This product contains heavy particles. Stir well before use. By providing a constantly active surface during its lifetime, this antifouling is gradually sacrificed in the process.

Colours/Colour stability: The ANTIFOULINGs are never tinted and as the high load of cuprous oxide influences the shade a certain variation from batch to batch is allowable. Exposure to humid weather shortly after application is likely to cause discolouration. This is a surface phenomenon only and has no influence on performance nor recoatability.

Film thicknesses/thinning: May be specified in another film thickness than indicated depending on purpose and area of use. This will alter spreading rate and may influence drying time and overcoating interval. Normal range dry is:80-150 micron/3.2-6 mils

HEMPEL'S ANTIFOULING GLOBIC 81900 For professional use only.Note:

Minimum undocking time depends on number of coats applied, film thickness, the prevailing temperature and the subsequent exposure/service conditions. For further information, please consult the corresponding painting specification. Maximum undocking time depends on the atmospheric conditions (UV radiation, temperature, degree of atmospheric pollution, etc.).Exposure to the atmosphere in up to 6 months normally presents no problems but extraordinary contamination may call for a freshwater high pressure hosing - contact Hempel.

Undocking:

Overcoating note: As per specification depending on existing hull condition, trading pattern, and intended service life.No maximum recoat interval, but after prolonged exposure to polluted atmosphere, remove accumulated contamination by high pressure fresh water cleaning and allow to dry before applying next coat. As for other physically drying paints the final hardness will be obtained a few days after application of the last coat. Precautions must be made taking this into account during e.g. out docking.

Redocking: At redocking, HEMPEL'S ANTIFOULING PAINT can be overcoated after thorough cleaning and removal of any poorly adhering surface layer or leached layer on the antifouling.Reference is made to SURFACE PREPARATION above. If overcoated with other types of antifouling,other surface preparation methods may be required - contact HEMPEL.

Aluminium hulls: May be specified on aluminium hulls provided an efficient anticorrosive system in minimum 2 coats of 150 micron/6 mils each has been applied. The anticorrosive system must stay intact during service in order to avoid corrosion of the aluminium caused by the cuprous oxide content of the Paint.Standard airless heavy-duty spray equipment:Pump ratio: min 45:1 (see Note below)Pump output: min 12 litres/minute (theoretical)Spray hoses: max 15 metres/50 feet, 3/8" internal diameter; max 3 metres/10 feet, 1/4" internal diameterNote: If longer spray hoses are necessary, up to 50 metres/150 feet hose (½" internal diameter) can be added. The pump ratio must be raised to 60:1 or more, however, the high output capacity of the pump must be maintained.A reversible nozzle is recommended.Filter: Surge tank filter and tip filter should be removed.

Application equipment:

HEMPEL'S ANTIFOULING GLOBIC 81900

This Product Data Sheet supersedes those previously issued.For explanations, definitions and scope, see “Explanatory Notes” available on www.hempel.com. Data, specifications, directions and recommendations given in this data sheet represent only test results or experience obtained under controlled or specially defined circumstances. Their accuracy, completeness or appropriateness under the actual conditions of any intended use of the Products herein must be determined exclusively by the Buyer and/or User.The Products are supplied and all technical assistance is given subject to HEMPEL's GENERAL CONDITIONS OF SALES, DELIVERY AND SERVICE, unless otherwise expressly agreed in writing.The Manufacturer and Seller disclaim, and Buyer and/or User waive all claims involving, any liability, including but not limited to negligence, except as expressed in said GENERAL CONDITIONS for all results, injury or direct or consequential losses or damages arising from the use of the Products as recommended above, on the overleaf or otherwise. Product data are subject to change without notice and become void five years from the date of issue.

ISSUED BY: HEMPEL A/S 8190051110

Page: 2/2

-Product Data SheetDate of issue: September 2014

For product description refer to product data sheet

HEMPADUR QUATTRO 17634

Issued: December 2014 Page 1 of 5

IMO Resolutions MSC.215(82) & MSC.288(87)

HEMPADUR QUATTRO 17634 17634: BASE 17636 with CURING AGENT 97334

Scope: These Application Instructions cover surface preparation, application equipment and

application details for HEMPADUR 17634 when applied in ballast tanks and cargo oil tanks according to the requirements in IMO Resolutions MSC.215(82) and MSC.288(87), respectively. Applications Instructions are also applicable for vessels not covered by PSPC.

Steel work (PSPC): The steel shall preferably be Rust Grade A or B according to ISO 8501-1. The use of steel

with Rust Grade C requires tighter inspection of surface profile after blasting as well as of possible salt contamination.

The steel surface shall be thoroughly prepared so that the coating achieves an even

distribution at the specified nominal dry film thickness of 320 micron and has an adequate adhesion. The final steel condition including welds and edges shall conform to preparation grade P2, ISO 8501-3: “Preparation of steel substrates before application of paints and related products - Visual assessment of surface cleanliness”.

Abrasive blasting/ abrasive sweep blasting: The coating system shall only be applied to steel primed with a pre-qualified, inhibitor-free

zinc silicate shopprimer. Steel shopprimed with a non-pre-qualified shopprimer must be abrasive blast cleaned to Sa 2 removing at least 70% of intact shopprimer. Steel which has not been shopprimed must be blasted to Sa 2½.

Before blasting, any deposits of grease or oil must be removed from the steel surface using a suitable detergent followed by fresh water hosing. Minor spots of oil/grease may be

cleaned with thinner and clean rags - avoid smearing out the contamination. Possible alkali weld deposits, chemicals used for testing of welds and soap residues from the pressure testing must be removed by fresh water hosing.

The shopprimer must have been checked randomly for excessive film thickness. Areas

detected to have film thicknesses above approx 40 micron/1.6 mils (as measured directly on the shopprimed surface with equipment calibrated on smooth steel) are to be blasted to Sa 2 removing at least 70% of the shopprimer.

Welds as well as shopprimed areas with damage, burn marks and rust must be blasted to Sa 2½.

When holding primer used, additional instructions on surface preparation shall be

considered. Prior to application of the holding primer the surface must be completely free of dust, contamination and any foreign matters.

The holding primer must be applied homogeneously and as close to the specification as

possible. Care must be taken to cover edges, openings, rear side of stiffeners, etc. Thus on these areas a stripe coat will need to be applied.

The surface must be completely clean and free of any contaminants before overcoating in

order to ensure proper inter-coat adhesion, and the coating must show no sign of degradation. Overcoating of the holding primer shall be in accordance with the overcoating intervals stated in the Product Data Sheet and Application Instructions of the holding primer.

Exposure of the holding primer to sun light should be avoided. Degradation from such

exposure or caused by other sources must be removed by mechanical cleaning methods like water jetting, abrading or preferably sweep abrasive blasting.

Mechanical and corrosion damages must be cleaned by abrasive blasting to Sa 2½, minor

areas may be mechanically cleaned to St 3, according to ISO 8501:1-2007. Prior to the application of the first full coat of HEMPADUR QUATTRO 17634, the entire

surface must be cleaned by appropriate means (which could include suitable detergent followed by high pressure fresh water cleaning depending on type and extent of contamination).

HEMPADUR QUATTRO 17634

Issued: December 2014 Page 2 of 5

If the maximum recoating interval as stated above is exceeded, roughening of the entire surface is required to ensure satisfactory inter-coat adhesion.

Surfaces with zinc salts, deposits of black iron oxides from plasma cutting, markings and

similar foreign matters shall be cleaned by light abrasive sweep blasting. Welds coated with a temporary shopprimer after welding must be cleaned by dry abrasive

blasting to a cleanliness degree of Sa2½ according to ISO 8501-1. Spot-checks for possible salt contamination of the surface must be executed after

secondary surface preparation. The upper water soluble salts limit is 50 mg/m² sodium chloride equivalents when measured according to ISO 8502-6:2006 and ISO 8502-9:1998. To limit salt contamination from abrasives it is recommended to use abrasives showing a water-soluble contaminant level equivalent to less than 25 mS/m according to ISO 11127-6:1993.

When blasting, the importance of working systematically must be stressed. Poorly blasted

areas covered with dust are very difficult to locate during the blast inspection made after the rough cleaning.

In the case of full or partial abrasive blast cleaning, the surface profile must conform to

Rugotest No. 3, BN9-10 or to ISO 8503-1, grade Medium (G).

Dust must be removed just before application of the paint to a dust quantity rating “1” for dust size classes “3”, “4” or “5” according to ISO 8502-3:1992. Lower dust size classes shall be removed from the surface if visible without magnification.

Note: If any doubt exists about the quality of the primary surface preparation (before

shoppriming), the substrate must be re-blasted in situ as defined above. Block assembly zones: Overlap zones must be treated with great care. Damage caused by

possible over-blasting must be avoided, paint edges feathered and consecutive layers of paint coatings given larger and larger overlaps. Roughening must be carried out when the maximum overcoating interval is exceeded (when sand papering, use free-cut paper, grain size 80).

Furthermore, these areas may also be masked off with tape to keep them as narrow as

possible. Application of a thin zinc epoxy primer coat on these areas after secondary surface preparation at block stage is acceptable if removed before the application of HEMPADUR 17634.

Secondary surface preparation of block assembly zones is preferably abrasive spot-blasting

to Sa 2½, when practicable, or mechanical cleaning to minimum St 3. The procedure of masking off with tape or using the zinc epoxy primer as described above may advantageously be used in case of mechanical cleaning.

Stainless steel: (E.g. Ballast tanks of chemical carriers) To be abrasive blast cleaned to a

uniform, sharp, dense, profile (equivalent to surface roughness comparator Rugotest No. 3, BN9-10 or ISO Comparator Medium (G), corresponding to Rz minimum 60 micron). Any salts, grease, oil etc. shall be removed before abrasive blasting is commenced. Surface preparation and paint application to be carried out concurrently with treatment of surrounding carbon steel. Paint application to take place as soon as possible after surface preparation of stainless steel is finalised.

Application equipment: HEMPADUR 17634, being a high viscosity material, may require special measures to be

taken at application. Recommended airless spray equipment: Pump ratio: min 45:1 Pump output: 12 litres/minute (theoretical) Input pressure: min. 6 bar/90 psi Spray hoses: max. 100 metres/300 feet, 1/2" internal diameter max. 30 metres/100 feet, 3/8" internal diameter max. 6 metres/20 feet, 1/4" internal diameter Filter: 60 mesh

HEMPADUR QUATTRO 17634

Issued: December 2014 Page 3 of 5

Nozzle size: 0.021" - 0.025" Fan angle: 60-80° To spray complicated surfaces a smaller nozzle size should be used. After finishing the application, clean the equipment immediately with HEMPEL’S TOOL

CLEANER 99610. Note: Increasing hose diameter may ease paint flow thereby improving the spray fan. If

longer hoses are used it may be necessary to increase the pump ratio to 60:1, maintaining the high output capacity of the pump.

Alternatively, up to approximately 5% THINNER 08450 may be added, but thinning must be

done with care as the maximum obtainable film thickness is reduced significantly by exaggerated thinning.

Airless spray data are indicative and subject to adjustment. Application: PSPC requires the application of minimum two spray applied coatings and minimum two

stripe coats. The relative humidity shall be maximum 85% and the steel temperature shall

be 3°C/5°F above the dew point.

Spray application: A continuous, pinhole-free paint film must be obtained at application of each spray applied coat. An application technique which will ensure good film formation on all surfaces must be adopted. It is very important to use nozzles of the correct size, not too large, and to have a proper, uniform distance of the spray gun to the surface, 30-50 cm should be aimed at. Furthermore, great care must be taken to cover edges, openings, rear sides of stiffeners etc. even though these areas also must be stripe coated. To obtain good and steady atomising, the viscosity of the paint must be suitable and the spray equipment must be sufficient in output pressure and capacity. At high working temperatures, use of extra thinner may be necessary to avoid dust spray.

The paint layer must be applied homogeneously and as close to the specification as

possible. Care shall be taken to avoid exaggerated film thicknesses. Wet film thickness shall be regularly checked during the application.

The finished coating must appear as a homogeneous film with a smooth surface. Any

defective areas, e.g. pin-holes, bubbles, voids, visible abrasive residues, shall be marked up and appropriate repair effected.

Stripe coating: The required two stripe coats must each be applied as a coherent film

showing good film formation and no visible defects such as pores or un-wetted areas. The application method must ensure that all areas which require stripe coating are properly stripe coated by alternative application methods which include brush or roller. Application by airless spray requires the use of relatively small, narrow-angled nozzles. PSPC accepts that the second stripe coat, by way of welded seams only, may be reduced in scope where it is proven that the nominal dry film thickness (NDFT) can be met by the coats applied. The first stripe coating should preferably be applied after first full coat to avoid contamination of the steel substrate.

Pot life/mixing/ induction time: When measured under standard conditions, the pot life for spraying is 3 hours at 15°C/59°F and 2 hours at 20°C/68°F. However, for a 20-litre/5-US gallon mix, the heat

developed by the chemical reaction between BASE and CURING AGENT may make the corresponding practical pot life shorter.

a. Mix the entire content of corresponding base and curing agent packing. If it is

necessary to mix smaller portions, this must be done properly by either weighing base and curing agent in the prescribed weight ratio: 86 parts by weight of base and 14 parts by weight of curing agent; or by volume: 4.0 parts by volume base and 1.0 part by volume curing agent.

b. Stir the mixed paint thoroughly by means of a clean mechanical mixer until a

homogeneous mixture is obtained. c. Use all mixed paint before the pot life is exceeded. The pot life depends on the

temperature of the paint as shown in table below (valid for a 20-litre can):

HEMPADUR QUATTRO 17634

Issued: December 2014 Page 4 of 5

Temperature of mixed paint 15°C/59°F1) 20°C/68°F 25°C/77°F 30°C/86°F2)

Pot life (spray application) 3 hours 2 hours 1½ hours 1 hour

1) Temperatures below 15°C/59°F should preferably be avoided. 2) Temperatures above 30°C/86°F should preferably be avoided.

Induction time: At steel temperatures below 5°C/41°F, the mixed paint may

advantageously be pre-reacted for 10-20 minutes before spray application (longer pre-reaction times at lower steel temperatures). Remix the paint again before application.

Two-component spray equipment: Heating may be required to obtain a proper spray fan and

a uniform and smooth paint film. This can either be done by preheating the two-component paint or by using a flow-heater on the pressure side. As an indication, a paint temperature of approximately 40°C/104°F will be relevant, but has to be adjusted according to the actual conditions.

Dry film thickness: PSPC requires that the nominal dry film thickness (NDFT) shall be 320 micron and shall be

achieved by minimum two spray coats and two stripe coats. The dry film thickness distribution shall be evaluated according to the 90/10 rule.

Dry film

thickness (DFT) DFT micron/mils Remarks

Minimum DFT

per coat 90/3.5

Value for undiluted paint at approximately 20°C/68°F. Lower DFT may be

achieved by thinning.

Maximum DFT

(complete coating

system) 2,000/80

The maximum DFT is valid for isolated spots less than 1% of the total

surface area per tank. No more than 5% of the area must be above 1,300

micron/52 mils. The stated maximum DFT is for guidance and should be

kept as close to the specified nominal DFT as possible. Frequent control of

wet film thickness during application is recommended.

Physical data versus temperature: (HEMPADUR 17634 in a dry film thickness of 160 micron/6.4 mils):

Surface temperature -10°C/14°F 0°C/32°F 10°C/50°F 20°C/68°F 30°C/86°F

Drying time

Walk-on time

Curing time

35 hours

42 hours

56 days

14 hours

21 hours

28 days

7 hours

9 hours

14 days

4 hours

4½ hours

7 days

3 hours

3½ hours

3½ days

Initial curing* 40 days 20 days 10 days 5 days 2½ days * When the state "initial curing" has been reached, the coating may exceptionally be exposed to ballast water provided it has been applied within the specified limits of film thicknesses and that all painted areas have been subject to thorough ventilation.

Overcoating: Overcoating intervals (provided proper ventilation) (HEMPADUR 17634 in a dry film thickness of 160 micron/6.4): Minimum overcoating interval

Steel temperature -10°C/14°F 0°C/32°F 10°C/50°F 20°C/68°F 30°C/86°F 40°C/104°F

Overcoating time* 49 hours 25 hours 11 hours 5 hours 4 hours 3 hours

Maximum overcoating interval

Steel temperature -10°C/14°F 0°C/32°F 10°C/50°F 20°C/68°F 30°C/86°F 40°C/104°F

Overcoating time** 90 days 90 days 60 days 30 days 22½ days 15 days

* Stripe coat can be applied when it is possible to walk on the surface without damage to the coating. ** Depending on actual local conditions, extended maximum overcoating intervals may apply. Please contact HEMPEL for further advice.

Long overcoating intervals

Roughening of the surface is necessary to ensure optimum intercoat adhesion if the

maximum overcoating interval is exceeded. A completely clean surface is mandatory to ensure intercoat adhesion, especially in the

case of long overcoating intervals. Any dirt, oil and grease have to be removed with e.g.

HEMPADUR QUATTRO 17634

Issued: December 2014 Page 5 of 5

suitable detergent followed by high pressure fresh water cleaning. Salts shall be removed by fresh water hosing.

Any degraded surface layer, as a result of a long exposure period, must be removed as well. Water jetting may be relevant to remove any degraded surface layer and may also replace the above-mentioned cleaning methods when properly executed. Consult HEMPEL for specific advice if in doubt.

To check whether the quality of the surface cleaning is adequate, a test patch may be relevant

Repair process: During construction Before mechanical surface preparation is started the areas to be repaired shall be cleaned

for any salts and other contamination. Overlap zones shall be suitably prepared and coated. Small areas: Small areas in this context are areas up to approximately A4 size (20x30 cm)

or scratches of up to a few millimetres across. Cracks, in corners or at single runners, may preferably be repaired according to this method, even if they fall outside the area definition.

The surface preparation can be executed by sanding or grinding to a clean rough metal

surface, feathering edges of intact coating and slightly roughening the adjacent surface and remove all dust. Touch-up with the coating material specified using stippling for the first brush coat.

Contiguous areas: Ballast tanks: Contiguous areas over 25 m²/270 sq.ft. or over 2% of the total area of the

ballast tank are to be repaired basically according to the original specification. Sa 2½ shall be applied.

Cargo oil tanks, inner bottom: Contiguous areas over 25 m²/270 sq.ft. or over 2% of the

total area of the cargo oil tank are to be repaired basically according to the original specification. Sa 2½ shall be applied.

Cargo oil tanks, underdeck: Contiguous areas over 25 m²/270 sq.ft. or over 3% of the total

area of the cargo oil tank are to be repaired basically according to the original specification. Sa 2½ shall be applied.

In all cases, damage due to over-blasting must be avoided. During service Maintenance and repair during service is subject to the actual condition of the area under

consideration. Reference is made to IMO Guidelines for maintenance and repair of protective coatings, MSC.1/Circ.1330 for ballast tanks and MSC.1/Circ.1399 for cargo oil tanks.

Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint

containers, consult HEMPEL Material Safety Data Sheets and follow all local or national safety regulations. Avoid inhalation, avoid contact with skin and eyes, and do not swallow. Take precautions against possible risks of fire or explosions as well as protection of the environment. Apply only in well ventilated areas.

ISSUED BY: HEMPEL A/S – 1763450630 These Application Instructions supersede those previously issued. For explanations, definitions and scope see “Explanatory Notes” available on www.hempel.com. Data, specifications, directions and recommendations given in this data sheet represent only test results or experience obtained under controlled or specially defined circumstances. Their accuracy, completeness or appropriateness under the actual conditions of any intended use of the Products herein must be determined exclusively by the Buyer and/or User. The Products are supplied and all technical assistance is given subject to HEMPEL's GENERAL CONDITIONS OF SALES, DELIVERY AND SERVICE, unless otherwise expressly agreed in writing. The Manufacturer and Seller disclaim, and Buyer and/or User waive all claims involving, any liability, including but not limited to negligence, except as expressed in said GENERAL CONDITIONS for all results, injury or direct or consequential losses or damages arising from the use of the Products as recommended above, on the overleaf or otherwise. Product data are subject to change without notice and become void five years from the date of issue.