SOUTHWEST OILFIELD PRODUCTS, INC.
10
® PUMP MAX MAX STROKE LINER SIZE IN INCHES MODEL I.H.P. S.P.M. LENGTH 5 5 ½ 6 6 ½ 7 7 ½ 8 8 ½ 9 14-P-220 2200 105 14” MAX-P.S.I. 7500 7475 6285 5360 4615 4025 3535 3130 2795 G.P.R. 3.57 4.32 5.14 6.03 7.00 8.03 9.14 10.31 11.57 G.P.M. @ 105 R.P.M 374.9 453.6 539.7 633.15 735 843.2 959.7 1082.6 1214.9 NOTE: I.H.P.= INPUT HORSE POWER S.P.M.= STROKE PER MINUTE P.S.I.= POUNDS PER SQUARE INCH G.P.R.= GALLONS PER REVOLUTION *MAX – P.S.I. CALCULATIONS DO NOT EXCEED MAXIMUM FLUID END PRESSURE RATINGS BASED ON 100% VOLUMETRIC EFFICIENCY AND 90% MECHANICAL EFFICIENCY SOUTHWEST OILFIELD PRODUCTS, INC. MUD PUMP EXPENDABLE PARTS LIST SOUTHWEST 8482-A FLUID END FOR NATIONAL 14-P-220 MUD PUMP PERFORMANCE CHART REV. B Page 1 of 10 10/15/15
Transcript of SOUTHWEST OILFIELD PRODUCTS, INC.
®
PUMP MAX MAX STROKE LINER SIZE IN INCHES
MODEL I.H.P. S.P.M. LENGTH 5 5 ½ 6 6 ½ 7 7 ½ 8 8 ½ 9
14-P-220 2200 105 14”
MAX-P.S.I. 7500 7475 6285 5360 4615 4025 3535 3130 2795
G.P.R. 3.57 4.32 5.14 6.03 7.00 8.03 9.14 10.31 11.57
G.P.M. @ 105 R.P.M 374.9 453.6 539.7 633.15 735 843.2 959.7 1082.6 1214.9
NOTE: I.H.P.= INPUT HORSE POWER S.P.M.= STROKE PER MINUTE P.S.I.= POUNDS PER SQUARE INCH G.P.R.= GALLONS PER REVOLUTION
*MAX – P.S.I. CALCULATIONS DO NOT EXCEED MAXIMUM FLUID END PRESSURE RATINGS
BASED ON 100% VOLUMETRIC EFFICIENCY AND 90% MECHANICAL EFFICIENCY
SOUTHWEST
OILFIELD PRODUCTS, INC. MUD PUMP EXPENDABLE PARTS LIST
SOUTHWEST 8482-A FLUID END
FOR NATIONAL 14-P-220
MUD PUMP PERFORMANCE CHART
REV. B Page 1 of 10 10/15/15
REV. B Page 2 of 10 10/15/15
1014"
44
89"
1
4 39 "
3
2"
792364"
10000# 5-1/8" BLIND FLANGEBX-169 RING JOINT GASKETS
SHEET 1 OF 1
SOUTHWEST OILFIELD PRODUCTS10340 WALLISVILLE ROAD, HOUSTON,TX 77013
MATERIAL
8482A-APL
09/13/2013
DATE
SOUTHWEST OILFIELD PRODUCTS. ANY
REPRODUCTION IN PART OR AS A WHOLE
SURFACE FINISH 125 RMS MAX
DISCHARGE CONNECTORS
BH
09/13/2013JM
N/A
D
C
B
AA
B
C
D
12
DWG. NO.
7
78
CHECKED
DRAWNUNLESS OTHERWISE SPECIFIED:
45
CONCENTRICITY NOT TO EXCEED.005 T.I.R.
REV
DATE
SOUTHWEST OILFIELD PRODUCTS IS
SIZE
3
HEAT TREAT
BREAK SHARP CORNERS 1/32 X 45° MAX
WITHOUT THE WRITTEN PERMISSION OF
PROHIBITED.
DRAWING IS THE SOLE PROPERTY OF
TITLE:
B
6 5 4 3 2 1
THE INFORMATION CONTAINED IN THIS
8
6
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL 1/64
ANGULAR: 0.5°
DECIMAL +.005 / -.000
ALL FILLETS & RADII - 1/16 MAX
CHAMFERS 1/16 X 45° MAX
PIPING LAYOUT FOR NATIONAL 14-P-220 SWFE W/ EXTERNAL
N/A
10"-150# ANSI FLANGES
1734" "
21
10
3634"
REV. B Page 3 of 10 10/15/15
ITEM
NO.
PART
NO.
DESCRIPTION
QTY.
REQ’D
8482-A FLUID END ASSEMBLY: (CONSISTS OF ITEMS 3, 4, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 32, 33, 34)
1 6382G-XX LINER (REFER TO GUIDE FOR ORDERING CHART FOR TYPE (G); (Y); AND FOR BORE SIZE (XX)) 3
2 2930-XX LINER SEAL 3
3 8482-4 WEARPLATE 3
4 2930-09 WEARPLATE & MODULE SEAL 6
5 XX-BYY PISTON (REFER TO GUIDE FOR ORDERING CHART FOR SIZE (XX) AND FOR TYPE (YY)) 3
6 568-225 PISTON O-RING 3
7 6282W32 PISTON ROD (W/ ELASTIC STOP NUT) 3
8 API-4ESN PISTON ROD ELASTIC STOP NUT 3
9 6282-1 SUB ROD 3
10 6282CWY ROD CLAMP (CONSIST OF 10A, 10B, 10C) (FOR CLAMP ONLY USE 6282C) 6
10A 1200H30 HOSE (1/2” X 30” WITH ½” MALE X 3/8” MALE CONNECTIONS) 6
10B 1200160 PIPE (3/8” X 16” GALVANIZED AND THREADED ON ONE END) 6
10C 4020-29 ROD CLAMP BOLT (3/4-10 GRADE 8 BOLT WITH LOCK NUT AND WASHER) 12
11 6200G82 PONY ROD 3
12 SEE PAGE VALVE 6
13 SEE PAGE VALVE INSERT (IF REQUIRED) 6
14 SEE PAGE VALVE SPRING 6
15 SEE PAGE VALVE SEAT 6
SWTM1700 HYDRAULIC SEAT PULLER KIT COMPLETE (REFER TO TOOLS SECTION IN CATALOG) 1
4482A VALVE COVER ASSEMBLY (CONSIST OF ITEMS NO. 16-23) 6
16 4482 THREADED FLANGE 6
17 4582 SCREW GLAND 6
18 4682A PLUG (COMPLETE WITH VALVE GUIDE, BUSHING, AND SCREWS, AND BUSHING) 6
19 P113 HP VALVE COVER PLUG NITRILE SEAL 6
20 4782R VALVE GUIDE (COMPLETE W/ BUSHING #4700I) 6
21 4700I VALVE GUIDE INSERT (ALSO AVAILABLE IN URETHANE PART# 4700IU) 6
22 4019-75 VALVE GUIDE SCREW 24
23 4015-54 VALVE COVER STUD (WITH SW PART# HHN1500-6 1 ½-6 HEAVY HEX NUT) 84
FLUID END TYPE MODEL OF PUMP SIZE OF PUMP
SOUTHWEST 7500 P.S.I. NATIONAL 14-P-220 9” X 14”
REV. B Page 4 of 10 10/15/15
FLUID END TYPE MODEL OF PUMP SIZE OF PUMP
SOUTHWEST 7500 P.S.I. NATIONAL 14-P-220 9” X 14”
ITEM
NO.
PART NO.
DESCRIPTION
QTY.
REQ’D
24 4019-24 POWER END STUD (WITH SW PART# HHN1500-6 1 1/2-6 HEAVY HEX NUT) 30
25 6482 LINER RETAINER FLANGE 3
26 4015-52 LINER RETAINER STUD (WITH SW PART# HHN1250-7 1 ¼-7 HEAVY HEX NUT) 18
27 6582 LINER RETAINER NUT 3
28 4019-74 SUCTION MODULE STUD (WITH SW PART# HHN2000-8 2-8 HEAVY HEX NUT) 18
29 4018-19 SUCTION MANIFOLD CAP SCREW 24
30 8582 SUCTION MANIFOLD 1
31 AJO326 SUCTION MANIFOLD SEAL 3
32 8482-2S SUCTION MODULE 3
33 8482-1D DISCHARGE MODULE 3
34 8488-5 DOWEL PIN 6
35 2982-3 DISCHARGE END ADAPTER SEAL 2
36 4017-4 DISCHARGE END ADAPTER CAP SCREW 24
37 BX169 RING JOINT 2
38 4020-21 BLIND FLANGE STUDS (WITH SW PART# HHN1125-7 1-1/8”-7 HEAVY HEX NUTS) 24
39 2982-2 DISCHARGE CONNECTOR SEAL 4
40 8382-1 DISCHARGE CONNECTOR 2
41 8382-3 DISCHARGE CONNECTOR BACK-UP RING 2
42 4018-18 DISCHARGE CONNECTOR CAPSCREW 16
43 2982-1 DISCHARGE CONNECTOR END SEAL 2
44 8382-2 DISCHARGE CONNECTOR ADAPTER 2
45 8382-4 DISCHARGE END FLANGE ADAPTER 2
** POLYURETHANE SEALS AVAILABLE**
REV. B Page 5 of 10 10/15/15
REV. B Page 6 of 10 10/15/15
SIZE FAIL-SAFE DUAL-DURO®
BLACK CAT GRAYLOY®
ZIRCONIA RUBBER URETHANE
5" 81BFS 81BDD 81BBC 6382G1 6382ZIR1 2930-1 2930-1U
5 1/2" 83BFS 83BDD 83BBC 6382G3 6382ZIR3 2930-3 2930-3U
6" 85BFS 85BDD 85BBC 6382G5 6382ZIR5 2930-5 2930-5U
6 1/2" 87BFS 87BDD 87BBC 6382G7 6382ZIR7 2930-7 2930-7U
7" 89BFS 89BDD 89BBC 6382G9 6382ZIR9 2930-9 2930-9U
7 1/2" 92BFS 92BDD 92BBC 6382G11 NA 2930-11 2930-11U
8" 94BFS 94BDD 94BBC 6382G13 NA 2930-13 2930-13U
SOUTHWEST 7500 PSI NATIONAL 14-P-220 GUIDE TO ORDERING
NOTE: DUAL-DURO® AND GRAYLOY® ARE REGISTERED TRADEMARKS OF SOUTHWEST® OILFIELD PRODUCTS.
LINER GASKETSLINERSPISTONS
REV. B Page 7 of 10 10/15/15
VALVE INSERT SPRINGSTAINLESS
SPRINGSEAT PULLER HEAD
PULLER HEAD
STYLE
SPLIT JAW
SWND-8V2 N/A SW5710-115L N/A SWND-8S7SWND-8PH
SWTM48-SN
PANCAKE
SPLIT JAW
SWND-8V2HC N/A SW5710-115L N/A SWND-8S7SWND-8PH
SWTM48-SN
PANCAKE
SPLIT JAW
N/A N/A N/A N/A N/A N/A
SWR0500120 SWR0515831 SWR0520503 SWR0520504 SWR0504845 SWTM3-8
SWR050012022 SWR051583101 N/A N/A N/A N/A
SWR0505109 SWR0504897 N/A SWR0514423 SWR0504845 SWTM3-8
SWU5B-23 SWUDD-8B SW5710-32 N/A SW8DD-B7 SWTM4-8
N/A N/A N/A N/A N/A N/A
SPLIT JAWPANCAKE
FULL OPEN-ROUGHNECK
(Cast N Place Insert Valve)
3 WEB DOUBLE ANGLE O-RING
TYPE
SOUTHWEST (Full Open)
3 WEB (High Temp)
4 WEB (High Temp)
4 J HOOK3 J HOOK
VALVES & SEATS (8482-A) 14-P-220
3 WEB STANDARD PLATE
4 WEB
FULL OPEN-ROUGHNECK
(High Temp)
FULL OPEN-ROUGHNECK
(w/Replaceable Urethane Insert)
3 J HOOK
4 J HOOK
REV. B Page 8 of 10 10/15/15
PART NUMBER DESCRIPTION COPPERCOTE MOLY GREASE DRY (NOT RECOMMENDED)
API-4 ESN PISTON NUT4019-77 ROD CLAMP BOLT4019-75 VALVE GUIDE SCREW 106 159 2124015-54 VALVE COVER STUD 1208 1752 24174019-24 POWER END STUD 1150 1668 23014015-52 LINER RETAINER STUD 669 940 13384019-74 SUCTION MODULE STUD 3463 5021 69254018-19 SUCTION MANIFOLD CAP SCREW 215 322 4304018-18 DISCHARGE CONNECTOR CAP SCREW 53 80 107
TORQUE SPECIFICATIONS FOR 8482-A SOUTHWEST FLUID END ASSEMBLY NATIONAL 14-P-220 7500 P.S.I.
TORQUE TYPE (EXPRESSED IN FOOT-POUNDS)
150 MAXIMUMNO MORE FORCE THAN ONE MAN ON 3' WRENCH/CHEATER COMBINATION
REV. B Page 9 of 10 10/15/15
Southwest Oilfield Products 10340 Wallisville Road, Houston, TX 77013 Office 713-675-7541
8482-A National 14-P-220 7500 PSI FLUID END REVISION SUMMARY
REVISION DATE REASON OF CHANGE
REV A 1/20/15 Changed Item No. 10C Part No. 4019-77 to 4020-29 what shows in MASS.
REV B 10/14/15 ADDED PART NO. 4482A VALVE COVER ASSEMBLY
REV. B Page 10 of 10 10/15/15
