Software Updating Chassis Lc7 115

Philips chassis LC7 Software updating page 1

<< software updating chassis LC7.xE >><< software updating chassis LC7.xE >>S

ER

VIC

E T

RA

ININ

G

CONSUMER LIFESTYLE

www.ayslearningcentre.philips.comAtYourService Learning Centre

Consumer Care

Hans MunstersMarch 2008

Software updating chassis LC7.xE

Philips Consumer Lifestyle, Consumer Care March 2008 <LC7.x software updating>, slide2

SDM mode:

To Enter: 062596 menu

To Exit: standby

SAM mode:To Enter: 0 6 2 5 9 6 follow by i+

To Exit: standby

CSM mode:To Enter: Using RC to key in 1 2 3 6 5 4

To Exit: Press Menu on RC

Display code 062598 menu xxx

Service modes



ER

VIC

E T

RA

ININ

G


Customer Service Mode page 1

Part of SW

12nc display


Customer Service Mode page 2

HDMI audio

Detected format

1080p board

Ambilight



ER

VIC

E T

RA

ININ

G


SSB top side

7H00 IBO software


SSB bottom side

7310 main software

IBO nvm

HDMI nvm (EDID)

I2C UART



ER

VIC

E T

RA

ININ

G


1080p board for full HD display

1080p software

There is no nvm on 1080p board

Nvm is integrated into main nvm on SSB

compair


Software Clustering:

Analogue LCD - LC71EL1_v1.24

Analogue PDP - LC71EP1_v1.24

Digital LCD - LC72EL1_v1.24

Digital PDP - LC72EP1_v1.24

Digital LCD - LC72ELH_v1.15 1080p display



ER

VIC

E T

RA

ININ

G


Software download via excel file


How to Program LC7 software ?

Behind the tuner there is I2C connection for Compair

Compair I2C

UART



ER

VIC

E T

RA

ININ

G


ComPair & UART Connector

ComPair Interface

ComPair UART Cable3122 785 90630

I²C Adaptor Cable with small connector

3139 131 03791

ComPair I²C cable 3122 785 90004

ComPair II interface 3122 785 91020


check possibility, if compairinterface is connected. This is software version of interface



ER

VIC

E T

RA

ININ

G


Compair installation program available as download, with driver

Driver is with installation program and is installed on your computer

This is the ComPair version 3 installer.Engine version 3.1.29.

System requirements:• Windows XP operating system.• USB connection for use with the ComPair II interface (preferably USB2.0).• Min. 256Mb RAM to make Windows XP run smoothly, 512Mb for Windows Vista.• Use ComPair with at least 1024x768 screen resolution on your PC.• Switch off screen savers and power management tools when using any set software upgrade feature in ComPair.

Known issues:• The Winamp MP3 player program interferes with the LC04 NVM read/write tool.• Starting up ComPair with something connected to the RS232/UART connector of the interface might cause a hang-up of ComPair.

Install ComPair II interface firmware 0.0.2.6.You can find the latest ComPair II interface firmware also on this website.The setup includes the USB driver for the new ComPair II interface. Please refer to the booklet packed with the USB interface to install the USB driver.ComPair version 3 is compatible with the old and the new interface, according to the ComPair settings applied. See the ComPair Feature and order code list (also available on this website) for details per chassis.Solved/added in this version:• Support for the LC08 platform added.• Support for the LC07 platform improved.• Support for TPM1.1U and TPM1.2U software upgrade feature.




ER

VIC

E T

RA

ININ

G



Select upgrade of the software or upgrade in case of empty flash * (then there is no feedback that the set is in Compairmode)

If software upgrade is completed (inclusive nvm), then type number, serial number, SSB, options have to be checked or programmed

Check in CSM•Empty flash (932221272668) does not work

•Preprogrammed IC:•313912709911 LC7.2E LB•313912709083 LC7.2E LA•313912701412 LC7.5E



ER

VIC

E T

RA

ININ

G


If the tv is in upgrade mode then also the red LED is on

Shorten I2C connector, in case something went wrong. TV-set is now also in upgrade mode

Follow the procedure for empty flash


1. Software upgrade,

2. Nvm

3. Displaycode

4. Typenumber

5. Serialnumber

6. SSB

7. Options

During upgrade black screen and red LED is blinking



ER

VIC

E T

RA

ININ

G


Upgrade nvm

In CSM version is indicated


Upgrade nvm

• Set is in factory mode à V-/P- local keyboard

• Check displaycode

• Disconnect all cables after upgrade!!Little load to I2C bus gives strange problems



ER

VIC

E T

RA

ININ

G


Model number programming

Add spaces to get 15 characters


Read production code, to check what is programmed



ER

VIC

E T

RA

ININ

G


Also 12nc SSB has to be programmed.

Read SSB 12 nc to check what is programmed


Via tools nvm edit

In case specific address has to be editted



ER

VIC

E T

RA

ININ

G


EDID nvm programming

For writing:

make sure the EEPROM in the set is NOT write protected (for the 24Cxx, pin 7 must be at 0V).


SSB board swop for home repair

DRAFT



ER

VIC

E T

RA

ININ

G


From the video processor various test pictures can be generated

Also from 1080p board


Service Alignment Mode



ER

VIC

E T

RA

ININ

G


Addresses in nvm where some data is stored:

407Option 7 (Smart Sound profile)

4

400Panel Option Code3

i.e. SV10003 30003215 - 228Serial No2

i.e. 32PFL5522D/12200 - 212Product Model1

RemarkTV NVMLocation (Dec)

DescriptionsNo.


GSC_66211 display option code list

Address 400 in nvm there can be checked which display is programmed



ER

VIC

E T

RA

ININ

G


Option codes are in service manual

displaycode

options


Alignments

White drive

– For analogue only try 15 (for DVB-T there is no AGC alignment)– Perfect alignment: insert IF and check voltage at pin 1 of the

tuner (analogue only)

Tuner AGC



ER

VIC

E T

RA

ININ

G


ComPair II• 2nd generation ComPair interface• Connects to PC via USB• Powered via USB• Supports UART (0V…+3V3/+5V

and -15V…+15V)• Supports I2C• Supports Infrared (RC5, RC6),

transmit and receive• HDMI connector for direct I2C

access to HDMI EDID EEPROM• Firmware can be upgraded• Will replace ComPair I from

beginning 2007

ComPair interfaces

ComPair I• Original ComPair interface• Connects to PC via UART• Needs separate power supply• Supports UART (0V…+5V)• Supports I2C• Supports Infrared (RC5, RC6), but

transmit only• Simulates Dealer Service Tool


ComPair order codes

• ComPairII interface: 3122 785 91020

• ComPair CD (release 2006-1): 3122 785 60160*– Installation CD with repair manuals upto January 2007.

• ComPair I2C cable: 3122 785 90004• ComPair I2C adapter cable: 3139 131 03791• ComPair UART cable: 3122 785 90630

• ComPair UART cable for TV520: 3104 311 12742– DB9 to 3.5mm headphone connectors

• ComPair I2C cable for LC7.5 9965 100 07325• ComPair UART cable for LC7.5 3138 188 75051

• ComPair cable for TPS1.0E 9965 100 09269

* installation program also available as downloadThis is the last Compair CD (all info is available via internet)



ER

VIC

E T

RA

ININ

G


How to access

• When you entered a model number, select the Model-Chassis relation link and select the appropriate type number.

• Via the ComPair link you can find all files


ComPair files for 32PFL5522D

installation

Software for the interface

Cpz - file

Nvm config



ER

VIC

E T

RA

ININ

G


Cpz-file for 32PFL5522D

Compair chassis fault finding file has to be downloaded as cpz-file




ER

VIC

E T

RA

ININ

G


Compatible with old interface

COMM port is auto detect

Restart ComPair browser

Then ComPair I is connected


www.AYSLearningCentre.philips.comwww.AYSLearningCentre.philips.com

Software Updating Chassis Lc7 115

Documents

Transcript of Software Updating Chassis Lc7 115